Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Effect of Lithium on the Discharge and Corrosion Behavior of Mg-3 wt.% Al Alloy as the Anode for Seawater Activated Battery

The discharge and corrosion behavior of Mg-3 wt.% Al alloys added with different contents of lithium in 3.5 wt.% NaCl aqueous solution is studied by electrochemical methods and microstructure characterization. The results indicate that adding 4 wt.% lithium severely promotes the self-corrosion and the addition of 12 wt.% lithium is not valuable to the spalling of discharge products. In contrast, doping Mg-3 wt.% Al with 8 wt.% lithium negatively shifts the discharge potentials and inhibits the self-discharge, attributed to the dual-phase structure of α-Mg plus β-Li that removes the discharge products and favors the uniform dissolution in the course of discharge. Moreover, the multi-pass rolling with 40% reduction could tailor the microstructure of Mg-3 wt.% Al-8 wt.% Li alloy and further enhance its discharge activity, even though the corrosion resistance is slightly reduced. This means that the rolled Mg-3 wt.% Al-8 wt.% Li sheet is suitable to serve as the anode for seawater activated battery.

36 MATERIALS SCIENCE↗

Development of a Novel Cr21 Lean Duplex Stainless Steel and Its Hot Deformation Behavior

In this study, a novel Cr21 lean duplex stainless steel has been developed. In order to investigate the difference in hot workability between the novel steel and the conventional LDX2101, the hot deformation tests were carried out in the temperature ranges from 950 to 1150 °C and strain rate ranges from 0.01 to 10 s{sup −1} by using a thermo-mechanical simulator. The peak stress increased with an increase in strain rate and a decrease in deformation temperature. However, the peak stress of the novel Cr21 lean DSS was always higher than that of the conventional LDX2101 under the same deformation conditions. The novel steel with lower deformation activation energy can be more easily deformed than the LDX2101. Meanwhile, the processing maps based on the specific plastic work approach indicated that the novel steel possessed a narrower flow instability region than the LDX2101. The lower difference in softening rate between ferrite and austenite can lead to the better deformation coordination in the novel steel compared to the LDX2101. The excellent hot workability of the novel steel can be obtained due to the low strength difference between the dual phases and the inhibition of the thin lamellar structures along the rolling direction on the transverse propagation of small cracks originating from the edge of the hot-rolled plates.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Pipeline Steel with Different Microstructures Under AC Interference in Acid Soil Simulation Solution

Corrosion behavior of X65 pipeline steels with different microstructures under alternating current (AC) interference was investigated in acid soil simulation solution by potentiodynamic polarization curve, potentiostatic polarization curve and immersion test. The results show that superimposed AC causes a sharp increase in corrosion current density of X65 steel. With the increase in i{sub AC}, the corrosion current densities of steels with various microstructures increase, especially at high i{sub AC}. Hot-rolled steel mainly experiences uniform corrosion, with very slight pit corrosion. Serious corrosion degrees with intensive corrosion pits can be observed on the surfaces of normalized and quenched microstructure steels. The annealed steel exhibits the feature of non-uniform corrosion with some pitting. The steels with various microstructures applied with AC have different corrosion resistance. The normalized steel shows the worst corrosion resistance, then the quenched microstructure, and the hot-rolled steel displays the optimum corrosion resistance. The difference in the microstructure can result in difference in corrosion degree and occurrence position of pitting corrosion of X65 steel. The normalized microstructure composed of polygonal ferrite and a large amount of pearlite and bainite is the most susceptible to AC corrosion.

36 MATERIALS SCIENCE↗

On Mechanical Properties of New Railway Wheel Steels for Desert Environments and Sand Caused Wheel Damage Mechanisms

Worn railway wheels after service in the desert were investigated by means of failure analysis, hardness measurements, tensile tests, fracture toughness tests and low-cycle fatigue (LCF) tests. The results complete both previous small-scale laboratory experiments and FEM simulations performed by the authors on widely used steels and new steel grades allowing to better understand the main damage mechanisms due to the sand. These new steel grades were developed for forged-rolled solid wheels in alternative to AAR Class B/C/D steel grades and were designed to ensure high resistance to wear and rolling contact fatigue in the presence of sand, debris or gravel on the rails. This paper covers the in-depth mechanical characterization of wheels made of the new steels. Hardness measurements, tensile tests, fracture toughness tests and LCF tests were carried out. The results are compared with AAR Class B/C/D steels showing an excellent combination of fracture toughness, cyclic yield strength and ductility.

36 MATERIALS SCIENCE↗

Interfacial Strength Evaluation of Oxide Films on Carbon Steel by Using the Laser Shock Adhesion Test

We investigate the adhesion strength (interfacial strength) of the oxide film formed on a carbon steel substrate by using a laser shock adhesion test (LaSAT). A rolled carbon steel (SS400) plate is first heated at high temperature (700 °C) under the atmosphere (heat treatment) to cause the formation of oxide films about 20-50 μm thick on the steel surface. The film consisted of multiple layers, including wustite (FeO), magnetite (Fe{sub 3}O{sub 4}), and hematite (Fe{sub 2}O{sub 3}). Next, the x-ray diffraction method was used to measure the residual stress in the film. We find that compression stress develops in the film because of a mismatch of thermal strain in between the film and substrate after the heat treatment. With LaSAT, strong elastic wave generates by a pulsed laser ablation of the substrate backside, and results in interfacial fractures in the oxide films. To monitor the normal (out-of-plane) displacement of the top surface film, a laser ultrasonic interferometer is simultaneously utilized, such that we detect film delamination and determine the critical laser energy for interfacial fracture to obtain the critical stress (interfacial strength). Furthermore, additional pulsed laser irradiation is conducted against a pre-delaminated specimen in order to examine the growth of delamination area and evaluate the interfacial fracture toughness. Finally, elastic wave propagation in the sample is computed using the finite element method (FEM) in order to evaluate the interfacial stress field, accurately. For the FEM, multiple layers in the oxide film are modeled, and the residual stress due to thermal strain mismatch is introduced. The FEM computations reveal the stress distribution around the interface and evaluate the critical stress and critical stress intensity factor for delamination. We thus quantitatively evaluate the interfacial strength and interfacial fracture toughness of the oxide film formed on carbon steel. The mechanism of interfacial fracture is also discussed on the basis of microstructures in a film with multiple layers. This result may be useful for understanding the adhesion quality of oxide film during the hot-rolling process.

36 MATERIALS SCIENCE↗

Effect of Stress States on Twinning Behavior in Twinning-Induced Plasticity Steel

The effects of stress state on the twin structures and kinetics in twinning-induced plasticity (TWIP) steel have been investigated to understand the twinning behaviors in more detail. Twinning behaviors of tension, compression, wire drawing, and caliber rolling were evaluated and compared using the EBSD technique, TEM measurement, and Schmid factor analysis. Twin structures, such as twin thickness, twin variant, twin shape, and twin kinetics were different with stress states. The specimen under compressive stress had wavy-shaped twins, less twin variant, lower twin thickness, and more twin volume fraction in comparison with the specimen under tensile stress. The different structures and kinetics of deformation twin with stress state were highly related to the grain rotation during plastic deformation. Under tensile stress, the grain rotation to <111> orientation, twinning-favored regions by Schmid factor analysis, encouraged the lateral growth of twins, more twin variants, and straight-type twins, while the grain rotation to <110> orientation under compressive stress suppressed the twin growth and twin variant and developed wavy-shaped twins. Drawn wire and caliber-rolled wire had both twin features under tensile and compressive stress states and higher twin volume fraction since complex stress state that combined tension and compression was applied in these processes. The hardness values were strongly related to the twin volume fraction with strain and stress state.

36 MATERIALS SCIENCE↗

Effect of Boron Micro-alloying on Microstructure and Corrosion Behavior of Dual-Phase Steel

The present work aims to understand the effect of boron (B) as a micro-alloying element on the mechanical properties and corrosion behavior of a dual-phase steel that was prepared from boron-added steel via hot rolling. The ‘B’ micro-alloying increased the volume fraction of martensite from ~ 25 to 50% and improved the hardenability as compared to unalloyed DP steel subjected to similar rolling and heat treatment conditions. The yield strength, tensile strength and corrosion resistance of boron-added DP steel significantly improved from 405 to 690 MPa, 632 to 890 MPa and 0.125 to 0.110 mm/year, respectively, as compared to the unalloyed DP steel.

36 MATERIALS SCIENCE↗

Significance of Finish Cooling Temperature to Microstructure and Property Relationship of Low-Carbon V-N-Cr Microalloyed High-Strength Steel

Herein, three final cooling temperatures were employed to achieve high strength and toughness communication in the V-N-Cr microalloyed steels. This study shows that V-N-Cr microalloyed steel primarily consisted of ferrite, granular bainite, acicular ferrite, and a small quantity of M/A phase at the final cooling temperature of 600 °C, while the polygonal ferrite, lamellar bainite, granular bainite, and a small fraction of acicular ferrite were obtained at 450 °C. The width of lamellar bainite was ~ 200-400 nm, and acicular ferrite was composed of fine non-parallel ferrite platelet structures with high dislocations densities. As the final cooling temperature decreased further, the microstructure included granular bainite and lath bainite at 350 °C. The nanoscale precipitates of V-N-Cr microalloyed steel were divided into two types, large-scale precipitates near the grain boundary that precipitated at high temperatures and small precipitates of diameter 5-10 nm at low temperatures, which significantly contributed toward strength. The hot rolled low-carbon V-N-Cr microalloy steel exhibited optimal mechanical properties at the final rolling temperature of 830 °C, as well the final cooling temperature was 450 °C. The highest yield strength and tensile strength of V-N-Cr microalloyed steel were 835 MPa and 989 MPa, respectively. The outstanding impact toughness of 161 J tested at − 60 °C was received. The transformation strengthening and precipitation hardening played a crucial role in affecting the thermo-mechanical properties.

36 MATERIALS SCIENCE↗

Microstructural and Textural Evolutions during β → α/ω Transformation in Biomedical Ti-15Mo Alloy and Its Effects on Mechanical Performance

This study investigated the precipitation behaviors and mechanical performance of Ti-15Mo alloy subjected to different treatment conditions. The microstructures were analyzed via scanning electron microscopy and transmission electron microscopy. The tensile properties and resultant fracture surfaces were investigated to determine the relationship between the phase transformation and mechanical performance. The Ti-15Mo alloy had a notable elongation due to no observable precipitation during solution treatment plus quenching (STQ). A high ultimate tensile strength (UTS) was obtained with a considerable amount of ω precipitates transformed during air cooling after solution treatment (ST). The coarse precipitates and additional precipitation free zones in the Ti-15Mo alloy treated with furnace cooling (FC) after ST induced a decrease in UTS. Furthermore, the absence of a continuous grain boundary α phase resulted in a lower strength in the specimen annealed at 600 °C after hot rolling. The alloy iso-aged after STQ exhibited good tensile properties with a UTS of 920 MPa and an elongation of 15%. The texture and variant relationship of the precipitates was analyzed with x-ray diffraction and electron backscatter diffraction. The common variants of the β matrix influenced the nucleation of precipitates in the Ti-15Mo alloy annealed after hot rolling, and the precipitates showed an obvious {01-10}α main texture. The variant selection of α precipitates at the grain boundary was caused by the two adjacent β grains in the alloy treated by FC after ST.

36 MATERIALS SCIENCE↗

Post-forming Room Temperature Brittle Fracture in a High-Strength Low-Alloy Steel Sheet After Various Forming Modes

The effects of various sheet forming modes on the post-forming room temperature fracture behavior of a 550-MPa yield strength high-strength low-alloy (HSLA) steel are investigated. In-plane biaxial stretching, plane strain (cold rolling), uniaxial tension, cylindrical cup drawing, and in-plane compression (IPC) are examined up to a von Mises effective prestrain ε{sub eff} = 0.7. Most of the results pertain to sub-size Charpy-type impact specimens prepared from the prestrained material. After sufficiently large prestrains, the fracture behavior is highly anisotropic. Low-energy fracture modes, namely cleavage and intergranular fracture, occur after all modes of prestraining along plane directions that are perpendicular to the principal compressive prestrain. These planes are parallel to the sheet surface after biaxial stretching and cold rolling and correspond to brittle splits extending into the primary, ductile fracture surface. After cup drawing, the brittle planes are oriented perpendicular to the circumferential compressive prestrain. This results in very low energy fractures propagating in the length direction of a fully drawn cup. After in-plane compression, brittle fracture occurs along planes that are perpendicular to the compression direction. The fracture toughness for a crack propagating along such a plane after IPC to ε{sub eff} = 0.38 was very low (12.7 MPa √m), much lower than in the undeformed condition (247 MPa√m). Changes in grain shape and in crystallographic texture caused by the various prestraining modes, as well as the microstructural damage at non-metallic inclusions and carbides, are examined to try to understand the fracture behavior.

36 MATERIALS SCIENCE↗

The Effect of Different Annealing Conditions on the Anisotropy of the Fracture Toughness of Ti-6Al-4V

The room-temperature tensile and fracture toughness properties of Ti-6Al-4V plate were tested to characterize the effect of rolling direction on the fracture toughness in two different heat treatment conditions. Optical and scanning electron microscopy was used to characterize the microstructure and fracture surfaces. It was found that beta annealing increased the fracture toughness compared to a mill annealed product in all three orientations relative to the rolling direction; however, it had minimal effects on strength and modulus. Ti-6Al-4V was found to be isotropic in fracture toughness, varying 0.48% in the beta annealed condition and 6.4% in the mill annealed condition.

36 MATERIALS SCIENCE↗

Significant Contribution to Strength Enhancement from Deformation Twins in Thermomechanically Processed Al{sub 0.1}CoCrFeNi Microstructures

Strengthening mechanisms from thermomechanical processing treatments were explored in single-phase FCC high-entropy alloy Al{sub 0.1}CoCrFeNi. Cold work offers substantial strengthening in this low stacking fault energy material owing to the resultant high work hardening rates. An enormous increase in yield strength of ~ 275% was obtained in 40% rolled material, but was accompanied by a steep drop in ductility. Recovery and recrystallization annealing treatments were investigated for improving elongation and obtaining better balance of strength–ductility combinations. Formation of novel microstructures from the different processing routes was examined. X-ray diffraction peak broadening and mechanical test results were coupled to estimate micro-strain in the different conditions and understand micro-strain’s correlation to strength. Retention of large-scale deformation twins formed during cold rolling is shown to play a key role in elevation of yield strength after heat treatments.

36 MATERIALS SCIENCE↗

Texture enhancement during grain growth of magnesium alloy AZ31B

In this paper, the microstructure and texture evolution during annealing of rolled Mg alloy AZ31B, at temperatures ranging from 260 to 450°C, is characterized, and a grain growth exponent of n=5, indicating inhibition of grain growth, is observed. Broadening of the normalized grain size distributions, which indicates abnormal grain growth, was observed at all temperatures investigated. It is shown, using a Zener-type analysis for pinning of grain boundaries by particles, that impurity-based particles are responsible for grain growth inhibition and abnormal grain growth. The strong basal texture which develops during rolling of the Mg alloy, resulting in an initial peak intensity in the (0002) pole figure of nine multiples of a random distribution (MRD), increases to ~15 MRD during annealing at 400 and 450°C. Furthermore, a specific texture component {0001}(1120) is observed in the orientation distribution, which increases from 10 to 23 MRD at 400°C. It is hypothesized that the anisotropic grain boundary properties (i.e. low angle boundaries have low energy and mobility) are responsible for the texture strengthening. Additionally, electron backscattered diffraction reveals the recrystallized microstructure to contain a significant number of boundaries with ~30° misorientation about the <0001> direction, and this boundary type persists throughout most annealing treatments explored.

36 MATERIALS SCIENCE↗

Effect of starting microstructure on helium plasma-materials interaction in tungsten

Here, in a magnetic fusion energy (MFE) device, the plasma-facing materials (PFMs) will be subjected to tremendous fluxes of ions, heat, and neutrons. The response of PFMs to the fusion environment is still not well defined. Tungsten metal is the present candidate of choice for PFM applications such as the divertor in ITER. However, tungsten's microstructure will evolve in service, possibly to include recrystallization. How tungsten's response to plasma exposure evolves with changes in microstructure is presently unknown. In this work, we have exposed hot-worked and recrystallized tungsten to an 80 eV helium ion beam at a temperature of 900 °C to fluences of 2 × 10 23 or 20 × 10 23 He/m 2 . This resulted in a faceted surface structure at the lower fluence or short but well-developed nanofuzz structure at the higher fluence. There was little difference in the hot-rolled or recrystallized material's near-surface (≤50 nm) bubbles at either fluence. At higher fluence and deeper depth, the bubble populations of the hot-rolled and recrystallized were different, the recrystallized being larger and deeper. This may explain previous high-fluence results showing pronounced differences in recrystallized material. The deeper penetration in recrystallized material also implies that grain boundaries are traps, rather than high-diffusivity paths.

36 MATERIALS SCIENCE↗

Role of microstructure on twin nucleation and growth in HCP titanium: A statistical study

In this study, a detailed statistical analysis is performed using Electron Back Scatter Diffraction (EBSD) to establish the effect of microstructure on twin nucleation and growth in deformed commercial purity hexagonal close packed (HCP) titanium. Rolled titanium samples are compressed along rolling, transverse and normal directions to establish statistical correlations for {10–12}, {11–21}, and {11–22} twins. A recently developed automated EBSD-twinning analysis software is employed for the statistical analysis. Finally, the analysis provides the following key findings: (I) grain size and strain dependence is different for twin nucleation and growth; (II) twinning statistics can be generalized for the HCP metals magnesium, zirconium and titanium; and (III) complex microstructure, where grain shape and size distribution is heterogeneous, requires multi-point statistical correlations.

36 MATERIALS SCIENCE↗

Modelling recrystallization textures driven by intragranular fluctuations implemented in the viscoplastic self-consistent formulation

This work presents a recrystallization model driven by intragranular orientation gradients and strain energy fields calculated by means of the viscoplastic self-consistent (VPSC) formulation. The VPSC model is extended for calculation of the coupling between intragranular stress fluctuations with corresponding second moments of lattice spin and misorientation fields in the grains. Access to these quantities allows modelling of transition bands and nucleation kinetics. In the proposed recrystallization model, grain growth is assumed to be proportional to the difference between the stored energy of each grain and that of the effective medium. Recrystallization textures for several cubic metals are simulated, showing good agreement with corresponding experiments. The model reveals the importance of considering appropriate, microstructurally-based and orientation-dependent recrystallization nucleation mechanisms. The recrystallization texture of heavily rolled copper with a strong cube texture component is found to be a consequence of nucleation at transition bands, which is also the cause of the recrystallization textures in compressed iron and drawn copper wire. Finally, in contrast, the recrystallization texture of rolled interstitial-free steel is found to be caused by grain boundary nucleation occurring in grains with the highest strain energy.

36 MATERIALS SCIENCE↗

Development of a variable tensioning system to reduce separation force in large scale stereolithography

Projection micro stereolithography (PµSL) is an additive manufacturing tool that offers multiple advantages, including unparalleled resolution and throughput, but the ability to print high viscosity resin for large-scale parts is limited. One of the key challenges in PµSL is to separate a newly polymerized layer from the vat floor without damaging the part. Since the separation force scales with the printing area, the risk of damaging the part increases significantly with larger-scale systems and must be addressed. In this paper, a novel roll-to-roll, variable tensioning system is proposed to reduce the separation force during printing. A mathematical model is proposed to predict the separation force for different 2D geometries, and a set of experiments is conducted on an experimental prototype to validate the model. Finally, the effects of different separation parameters including peel rate and peel angle are discussed in detail. The results show that the proposed tensioning system reduces the separation force significantly.

36 MATERIALS SCIENCE↗

Cartan gravity, matter fields, and the gauge principle

Gravity is commonly thought of as one of the four force fields in nature. However, in standard formulations its mathematical structure is rather different from the Yang–Mills fields of particle physics that govern the electromagnetic, weak, and strong interactions. This paper explores this dissonance with particular focus on how gravity couples to matter from the perspective of the Cartan-geometric formulation of gravity. There the gravitational field is represented by a pair of variables: (1) a ‘contact vector’ V{sup A} which is geometrically visualized as the contact point between the spacetime manifold and a model spacetime being ‘rolled’ on top of it, and (2) a gauge connection A{sub μ}{sup AB}, here taken to be valued in the Lie algebra of SO(2,3) or SO(1,4), which mathematically determines how much the model spacetime is rotated when rolled. By insisting on two principles, the gauge principle and polynomial simplicity, we shall show how one can reformulate matter field actions in a way that is harmonious with Cartan’s geometric construction. This yields a formulation of all matter fields in terms of first order partial differential equations. We show in detail how the standard second order formulation can be recovered. In particular, the Hodge dual, which characterizes the structure of bosonic field equations, pops up automatically. Furthermore, the energy–momentum and spin-density three-forms are naturally combined into a single object here denoted the spin-energy–momentum three-form. Finally, we highlight a peculiarity in the mathematical structure of our first-order formulation of Yang–Mills fields. This suggests a way to unify a U(1) gauge field with gravity into a SO(1,5)-valued gauge field using a natural generalization of Cartan geometry in which the larger symmetry group is spontaneously broken down to SO(1,3)×U(1). The coupling of this unified theory to matter fields and possible extensions to non-Abelian gauge fields are left as open questions. -- Highlights: •Develops Cartan gravity to include matter fields. •Coupling to gravity is done using the standard gauge prescription. •Matter actions are manifestly polynomial in all field variables. •Standard equations recovered on-shell for scalar, spinor and Yang–Mills fields. •Unification of a U(1) field with gravity based on the orthogonal group SO(1,5)

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗