Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Empirical Investigation of Electricity Self-Generation in a Lubricated Sliding–Rolling Contact

The paper reports the empirical observations of voltage generation in a lubricated tribocontact with different oils altering load, sliding and temperature. The investigation is done in the context of research of the root cause of white etching cracks (WEC) failure in bearings. Tested oils of different additive packages found completely different electrical behavior. The oil, which is known to produce WECs in laboratory tests, demonstrated non-zero voltage generation

Electricity↗
DOE OSTI2020

High performance Nb/TiNi nanocomposites produced by packaged accumulative roll bonding

Taking full advantage of intrinsic high strength of nano-reinforcements has been proven difficult in a composite until the concept of strain matching was experimental verified in a nanowire Nb/TiNi in-situ composite, which was obtained via solidifying eutectic Nb/TiNi and subsequent severe wire drawing. However, the volume fraction of the nano-reinforcement was dictated by eutectic reaction, which severely limited the development of high-performance composites. Here, the martensitic transformation nanocomposites were successfully acquired with increased volume fraction and changeable morphology of the nano-reinforcement through hot packaged ARB (PARB) and subsequent wire drawing. The nano-reinforcement with lamellar configuration in the composite could exhibit a large lattice strain of similar to 3.8%, which demonstrated the applicability and effectiveness of the strain matching principle in nano-lamellar composite. The obtained composites show a yield strength over 2.0 GPa and a quasi-linear elastic strain as larger as similar to 6.5% with adjustable apparent elastic modulus from 30 to 50 GPa.

42 ENGINEERING↗
DOE OSTI2020

Impact of the adhesion-force lever-arm “a” on the Rock ‘n’ Roll resuspension model and how to compute it from contact mechanics

The paper proposes a methodology to fill a gap in the context of mechanistic particle resuspension models related to the adhesion and lift force lever arms ( a ): to date, only one experimental observation exists from a centrifuge experiment with a specific particle/surface pair which found r P / a = 100 and assumed that the contact points were symmetric with respect to the particle center. However, the Reeks and Hall’s (2001) model is highly sensitive to this parameter, which therefore cannot be used as-is for different particle diameters or materials. This paper proposes a methodology to compute the adhesion and lift force lever arms ( a A and a L , respectively) based on Atomic Force Microcopy (AFM) surface roughness measurements and contact mechanics arguments. In practice, a spherical, perfectly smooth particle is brought in contact (computationally) with the measured surface roughness and is then rotated by the point of contact to determine the two or more asperities over which the particle would sit on the surface. A method to compute the asperity radius of curvature is devised to compute the asperity deformation and the correct partitioning of the total deformation between the particle and the asperity is presented. For the glass surface under consideration, the asperity deformation was negligible, i.e., it was below the van der Waals radius, which is the limit of applicability of contact mechanics. The Reeks and Hall’s (2001) model is then extended to account for the joint probability of a A and a L . Significant differences in particle resuspended after a day in common atmospheric conditions are found between the approach that uses the lever-arm distributions or their mean values. Also, important differences are found when comparing the lever-arm distribution and r P / a = 100. Hence, one should be cautious of using r P / a = 100 for surface/particle pairs differing from those in the original study. Finally, limits of applicability of the theories used are presented together with considerations regarding how to extend the method to non-spherical particles and different materials.

42 ENGINEERING↗
DOE OSTI2021

Oxygen enrichment combustion to reduce fossil energy consumption and emissions in hot rolling steel production

The reheating furnace operation in the hot mill is natural gas- and electricity-intensive. Oxygen enrichment combustion for reheating furnaces has been proposed to curb and replace natural gas use. In this study, heat transfer in steel slabs in the combustion environment of a push-type reheating furnace was simulated using a computational fluid dynamics (CFD) model. Two oxygen enrichment methods that optimized for performance were selected— a medium oxygen enrichment (MOE) case and an oxy-fuel (OF) case. A life cycle analysis (LCA) characterized the energy and emission profiles of an integrated iron and steel manufacturing process using the two oxygen enrichment cases for the hot mill. These conditions were evaluated for energy use and carbon intensity and compared with a baseline case. Results show that with oxygen enrichment, natural gas consumption can decrease by 19.6%–26.8%, total energy consumption (natural gas and electricity) can decrease by 15.1%–20.7% in the hot mill. Emissions of greenhouse gases can decrease by 11.1%–15.2% in the two optimized cases with 14%–27% reductions in regulated criteria pollutants (nitrogen oxides, carbon monoxide, particulate matter, volatile organic compounds, black carbon, organic carbon, and volatile organic carbons). There is a tradeoff between reducing natural gas consumption and increasing electricity demand from a life cycle perspective. Although the OF case resulted in higher energy- and emissions-related benefits, the MOE case showed the more desirable heat flux uniformity, which is key to maintaining product quality. The analysis suggests that oxygen enrichment in the reheating furnace process can have a significant impact on hot mill environmental performance and become a contributing factor in transitioning to low-carbon steel manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Migration of grain boundaries and triple junctions in high-purity aluminum during annealing after slight cold rolling

Grain orientations and grain boundary migrations near triple junctions in a high purity aluminum were analyzed by electron back scattered diffraction. The results indicate that there are good correlations between the Schmid factors or Taylor factors and the misorientation values of point to original point in grains near the triple junctions in a slightly deformed sample. Grains with higher Schmid factors or lower Taylor factors typically correspond to higher misorientation values near the triple junctions. In a subsequent annealing at 400 °C, both grain boundaries and triple junctions migrate, but the former leave ghost lines. During such migration, a grain boundary grows from the grain with lower Schmid factor (higher Taylor factor) into the grain with higher Schmid factor (lower Taylor factor). Usually, the amount of migration of a grain boundary is considerably greater than that of a triple junction, and the grain boundary becomes more curved after migration. These observations indicate that the triple junctions have drag effects on grain boundary migration. - Highlights: • Polycrystalline aluminum with fine grains about 30 μm were used. • Off-line in situ EBSD was used to identify TJs before and after annealing. • Grains with higher SFs have higher misorientation values near TJs after deformation. • Grain boundaries grow from hard grains into soft grains during annealing. • Triple junctions have drag effects on grain boundaries migration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Self-rolling of an aluminosilicate sheet into a single walled imogolite nanotube: The role of the hydroxyl arrangement

Imogolite is an inorganic nanotube, that forms naturally in weathered volcanic ashes, and it can be synthesized in nearly monodisperse diameters. However, long after its successful synthesis, the details of the way it is achieved are not fully understood. Here we elaborate on a model of its synthesis, which starts with a planar aluminosilicate sheet that is allowed to evolve freely, by means of classical molecular dynamics, until it achieves its minimum energy configuration. The minimal structures that the system thus adopts are tubular, scrolled, and more complex conformations, depending mainly on temperature as a driving force. Here we focus on the effect that the arrangement of the hydroxyl groups in the inner wall of the nanotube have on the minimal nanotubular configurations that we obtain are monodispersed in diameter, and quite similar to both from the those of weathered natural volcanic ashes, and to the ones that are synthesized in the laboratory. In this contribution we expand on the atomic mechanisms behind those behaviors.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A Linear Programming Approach to Backtracking for Single-Axis Trackers on Rolling Terrain

In this article, we present a computationally efficient method for determining optimal backtracking rotations for single-axis solar trackers on nonuniform terrain. The method allows for ganged tracking, mechanical rotation constraints, uneven row spacing, and arbitrary maximum allowable shaded fractions (to enable “fractional backtracking”). As with previous 2-D approaches, the method is suitable for terrain that varies in the transverse direction with respect to the rotation axis of the trackers. The novelty of the method lies in formulating the problem of shade avoidance as a linear problem, which is achieved by using the row interception width as the optimization variable instead of rotation angles. Formulating backtracking as a linear problem enables the use of extremely efficient linear programming algorithms, making the method highly scalable, requiring less than 1 min to compute optimal rotation schedules for hundreds of trackers. It also produces more effective backtracking rotations, reducing the frequency of shading by 4× and improving system energy output by 1%–2%.

Optimization↗
DOE OSTI2024

Cast Alumina-Forming Austenitic Stainless Steels for High Temperature Heat Treatment Furnace Rolls

Alloy developers worldwide have struggled to create creep-resistant alumina-forming, iron-based austenitic stainless steels for use as high-temperature structural alloys, but with limited success in balancing alloy cost, oxidation, and creep resistance. Here, this article describes the research and development of a novel cast alumina-forming austenitic stainless steel. This work won the prestigious Engineering Materials Achievement Award presented at IMAT 2023 in Detroit.

36 MATERIALS SCIENCE↗