Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Plutonium loading capacity of reillex™ hpq anion exchange column - AFS-2 plutonium flowsheet for mox

Radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the dependence of column loading performance on the feed composition in the H-Canyon dissolution process for plutonium oxide (PuO 2 ) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). These loading experiments show that a representative feed solution containing ~5 g Pu/L can be loaded onto Reillex™ HPQ resin from solutions containing 8 M total nitrate and 0.1 M KF provided that the F is complexed with Al to an [Al]/[F] molar ratio range of 1.5-2.0. Lower concentrations of total nitrate and [Al]/[F] molar ratios may still have acceptable performance but were not tested in this study. Loading and washing Pu losses should be relatively low (<1%) for resin loading of up to 60 g Pu/L. Loading above 60 g Pu/L resin is possible, but Pu wash losses will increase such that 10-20% of the additional Pu fed may not be retained by the resin as the resin loading approaches 80 g Pu/L resin.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Rapid determination of radiostrontium in seawater samples

A new method for the determination of radiostrontium in seawater samples has been developed at the Savannah River National Laboratory (SRNL) that allows rapid preconcentration and separation of strontium and yttrium isotopes in seawater samples for measurement. The new SRNL method employs a novel and effective pre-concentration step that utilizes a blend of calcium phosphate with iron hydroxide to collect both strontium and yttrium rapidly from the seawater matrix with enhanced chemical yields. The pre-concentration steps, in combination with rapid Sr Resin and DGA Resin cartridge separation options using vacuum box technology, allow seawater samples up to 10 liters to be analyzed. The total 89 Sr + 90 Sr activity may be determined by gas flow proportional counting and recounted after ingrowth of 90 Y to differentiate 89 Sr from 90 Sr. Gas flow proportional counting provides a lower method detection limit than liquid scintillation or Cerenkov counting and allows simultaneous counting of samples. Simultaneous counting allows for longer count times and lower method detection limits without handling very large aliquots of seawater. Seawater samples up to 6 liters may be analyzed using Sr Resin for 89 Sr and 90 Sr with a Minimum Detectable Activity (MDA) of 1-10 mBq/L, depending on count times. Seawater samples up to 10 liters may be analyzed for 90 Sr using a DGA Resin method via collection and purification of 90 Y only. If 89 Sr and other fission products are present, then 91 Y (beta energy 1.55 MeV, 58.5 day half-life) is also likely to be present. 91 Y interferes with attempts to collect 90 Y directly from the seawater sample without initial purification of Sr isotopes first and 90 Y ingrowth. The DGA Resin option can be used to determine 90 Sr, and if 91 Y is also present, an ingrowth option with using DGA Resin again to collect 90 Y can be performed. An MDA for 90 Sr of <1 mBq/L for an 8 hour count may be obtained using 10 liter seawater sample aliquots.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Applications of a dual-column technique in actinide separations

Selective separation of an individual actinide of interest from other actinides and accompanying lanthanides is a challenging task in radiochemistry and radioanalytical chemistry. This paper illustrates a dual column technique (i.e., stacked columns of two appropriate resins) to separate an individual actinide of interest, where the selection of two resins and a common effluent running through the stacked columns are key parameters in design of an appropriate dual column. This paper describes the dual column design and practice with two examples, one for a heavy actinide 249Bk and the other for a light actinide 230U. In the former case, stacked columns of anion exchange (AX) resin and LN resin replaced the traditional CX-AHIB method used at Oak Ridge National Laboratory for 60 years. In the latter case, an elution process with an AX column followed with a stacked column of AX resin and a DGA resin was applied, instead of traditional methods, e.g., PUREX or U-TEVA methods. Application results of the dual column method to the two example actinides are displayed, while the considerations in method design and the required conditions are discussed.

Du, Miting↗

Extraction Chromatographic Methods in the Sample Preparation Sequence for Thermal Ionization Mass Spectrometric Analysis of Plutonium Isotopes

A sample preparation sequence for actinide isotopic analysis by TIMS is described that includes column-based extraction chromatography as the first separation step, followed by anion exchange column separations. The sequence is designed to include a wet ashing step after the extraction chromatography to prevent any leached extractant or oxalic acid eluent reagents from interfering with subsequent separations, source preparation, or TIMS ionization. TEVA-resin and DGA-resin materials, containing extractants that consist only of C, N, O, and H atoms, were investigated for isolation of plutonium. Radiotracer level studies confirmed expected high yields from column-based separation procedures. Femtogram-level studies were carried out with TIMS detection, using multiple isotopic spikes through the separation sequence. Pu recoveries were 87% and 86% for TEVA- and DGA-resins separations respectively. The Pu recoveries from 400 {mu}L anion-exchange column separations were 89% and 93% for trial sequences incorporating TEVA and DGA-resin. Thus, a prior extraction chromatography step in the sequence did not interfere with the subsequent anion exchange separation when a simple wet ash step was carried out in between these column separations. The average measurement efficiency, for Pu, encompassing the chemical separation recoveries and the TIMS ionization efficiency, was 2.73 {+-} 0.77% (2-sigma) for the DGA-resin trials and 2.67 {+-} 0.54% for the TEVA-resin trials, compared to 3.41% and 2.37% (average 2.89%) for two spikes in the experimental set. These compare with an average measurement efficiency of 2.78 {+-} 1.70%, n = 33 from process benchmark analyses using Pu spikes processed through a sequence of oxalate precipitation, wet ash, iron hydroxide precipitation, and anion exchange column separations. We conclude that extraction chromatography can be a viable separation procedure as part of a multistep sequence for TIMS sample preparation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electron Tomography of Cryo-Immobilized Plant Tissue: A Novel Approach to Studying 3D Macromolecular Architecture of Mature Plant Cell Walls In Situ

Cost-effective production of lignocellulosic biofuel requires efficient breakdown of cell walls present in plant biomass to retrieve the wall polysaccharides for fermentation. In-depth knowledge of plant cell wall composition is therefore essential for improving the fuel production process. The precise spatial three-dimensional (3D) organization of cellulose, hemicellulose, pectin and lignin within plant cell walls remains unclear to date since the microscopy techniques used so far have been limited to two-dimensional, topographic or low-resolution imaging, or required isolation or chemical extraction of the cell walls. In this paper we demonstrate that by cryo-immobilizing fresh tissue, then either cryo-sectioning or freeze-substituting and resin embedding, followed by cryo- or room temperature (RT) electron tomography, respectively, we can visualize previously unseen details of plant cell wall architecture in 3D, at macromolecular resolution (~2 nm), and in near-native state. Qualitative and quantitative analyses showed that wall organization of cryo-immobilized samples were preserved remarkably better than conventionally prepared samples that suffer substantial extraction. Lignin-less primary cell walls were well preserved in both self-pressurized rapidly frozen (SPRF), cryo-sectioned samples as well as high-pressure frozen, freeze-substituted and resin embedded (HPF-FS-resin) samples. Lignin-rich secondary cell walls appeared featureless in HPF-FS-resin sections presumably due to poor stain penetration, but their macromolecular features could be visualized in unprecedented details in our cryo-sections. While cryo-tomography of vitreous tissue sections is currently proving to be instrumental in developing 3D models of lignin-rich secondary cell walls, here we confirm that the technically easier method of RT-tomography of HPF-FS-resin sections could be used immediately for routine study of low-lignin cell walls. As a proof of principle, we characterized the primary cell walls of a mutant (cob-6) and wild type Arabidopsis hypocotyl parenchyma cells by RT-tomography of HPF-FS-resin sections, and detected a small but significant difference in spatial organization of cellulose microfibrils in the mutant walls.

59 BASIC BIOLOGICAL SCIENCES↗

Conformable Hydrogen Storage Pressure Vessel

Existing commercially available hydrogen storage technologies are largely based on bulky and costly pressure vessels. These pressure vessels come in various forms, ranging from Type I steel cylinders to Type III and Type IV composite wrapped cylinders with metallic or polymer liners. In efforts to increase the pressure vessel storage density and meet DOE hydrogen storage targets, manufacturers are making incremental improvements. This approach alone is unlikely to meet DOE hydrogen storage targets and increase adoption of hydrogen fuel cell vehicles. The project team, led by the Center for Transportation and the Environment (CTE) and consisting of High Energy Coil Reservoirs, LLC (HECR) and The University of Texas at Austin's Center for Electromechanics (UT-CEM), has investigated a transformational hydrogen storage technology using high pressure modulus polymeric pressure vessels. These vessels are constructed by overwrapping an extruded thermoplastic elastomeric resin liner with high performance tensile fiber. This technology is used in commercially available compressed air storage for firefighters. The result is a lightweight, flexible, non-explosive, and non-fragmenting pressure vessel that can be shaped (prior to pressurization) to conform to specific applications. Although this project was funded to investigate the potential for this technology for vehicle applications, a potential significant cost reduction allowed with this approach may make it effective for high pressure ground storage as well. As part of Phase I of this project, the research team demonstrated a Kevlar™ over-braid that achieves a burst pressure in excess of 3.1X the operating pressure of 700 bar. The conformable vessel is able to achieve this pressure rating with reduced weight and cost when compared to Type IV vessels. The researchers also identified two potential resins to serve as the liner of the vessel. These resins have excellent hydrogen barrier properties that could enable a liner thickness of 0.06 inches or less; however, difficulties in manufacturing the core due to the extrusion manufacturing processes required testing with prototype resins as commercially available resins were not found that had the required properties. The team was able to build and test a vessel with one such blend, which outperformed the baseline Hytrel resin materials but did not meet the project hydrogen permeability rate goals.

08 HYDROGEN↗

Using low cost, bio-derived and recycled materials in advanced scalable small- and medium- wind turbine manufacturing

In partnership with Bergey Windpower, this project explored the use of recyclable and recycled materials in small- to medium-wind turbine blades (WTBs). A recyclable epoxy resin and infusible thermoplastic resin were investigated using identical fiber reinforcements and manufacturing practices used as Bergey, and the substitution of continuous virgin glass fiber (GF) layers with recycled nonwoven GF (rGF, NW) mats was trialed. The alternative resins both showed very promising performance in terms of static tensile and flexural behavior as well as thermal properties and fatigue behavior in comparison with that of the incumbent materials used at Bergey. The NW rGF materials, however, were found to be a poor substitute for the continuous GF materials for two primary reasons. Firstly, the NW mats took up significantly more resin than their continuous counterparts, which would increase both the weight and the cost of the WTBs. Additionally, an unexpected reaction occurred between the rGF and epoxy materials that resulted in a highly porous, foamed structure. The foaming phenomenon was not observed with the rGF NW and infusible thermoplastic material, but the resin uptake was still prohibitively high. Based on the results of this study, recyclable infusible resins could be viable candidate materials for Bergey in the future. The foaming reaction with the rGF NW mats could prove highly useful in other applications requiring structural foams and has been used to produce demonstrative sandwich panels.

17 WIND ENERGY↗

Resin/fiber thermo-oxidative interactions in PMR polymide/graphite composites

The amounts of resin weight loss and fiber weight loss in four PMR-polyimide graphite fiber composites were calculated from the composite weight losses and the fiber/resin ratios of the composites after long term thermo-oxidative aging in 600 F air. The accelerating effect of graphite fiber on resin weight loss, compared to neat resin weight loss, indicated the presence of a deleterious resin/fiber thermo-oxidative interaction, presumably due to fiber impurities. Similarly, the decelerating effect of the protective matrix resin on fiber weight loss, compared to bare fiber weight loss, was also demonstrated. The amount of hydrazine-indigestible resin and the amount of loose surface graphite fiber that formed during 600 deg F exposure of the composites were quantitatively determined. The indigestible residual resin was also qualitatively studied by scanning electron microscopy.

Alston, W. B.↗

Development of critical molecular weight-property specifications for high performance polymers used as adhesives and composites

The polyimide resin, LARC-160, was prepared from diethyl-3, 3', 4,4'-benzophenone tetracarboxylate, ethyl-5-norbornene-2,3-dicarboxylate and Jeffamine AP-22. The imidization reactions of NE and BTDE were studied by HPLC, C-13-NMR and IR. NE imidizes slowly at 12 C; BTDE imidizes when the resin is heated above 100 C. Both imidization reactions proceed directly to the imide. Neither amic acid is present in significant quantities at any stage of the imidization reactions. The monomer mixture was stored at 12 C for periods up to 14 months. The effects of resin aging at this temperature on the chemical composition of the resin monomer mixture and the imidized polymer formed on curing were investigated. Aging the resin monomer mixture has the effect of partially advancing the imidization reaction. The average size of the cured polymer increases slightly with resin age.

Kranbuehl, D. E.↗

The properties of novel bisimide amine cured epoxy/Celion 6000 graphite fiber composites

The study is concerned with the further development of bisimide amine cured epoxy resins first reported by Serafini et al. (1979). Attention is given to properties of the neat resins and composites made with these novel epoxy resins and Celion 6000 graphite fibers. The use of bisimide amine hardeners to cure epoxy resins causes a significant improvement in the char-forming characteristics of the cured resin. Compared to epoxy resins cured with a conventional amine, such as 4,4'-diaminodiphenylsulfone, the bisimide cured epoxies exhibit about a twofold improvement in the aerobic char yield at 800 C. The levels of moisture absorption exhibited by the bisimide amine cured epoxies were found to be considerably lower than those exhibited by state-of-the-art epoxies (0.5 wt.% versus 2.0%).

Scola, D. A.↗

Fundamental Studies of Composite Toughness

Evaluation of drop weight impact testing of neat resin and crossplied graphite fiber reinforced composites resulted in three conclusions: (1) during impact of cross-ply laminates, resin properties appear to influence the extent and mechanism of damage propagation; (2) by itself, neat resin strain to fracture is not a controlling influence on resin or composite fracture toughness; and (3) impact failure energy of neat resin plates can give a misleading indication of the resin contribution to composite impact behavior because of differences in the magnitude of diaphragm action in the two systems. Both geometric and composite constituent materials properties influence the drop weight impact resistance of crossplied composite plates. The matrix influence appears to be reflected in the incipient damage mechanism and the propagation of damage.

Bowles, K. J.↗

New acousto-ultrasonic techniques applied to aerospace materials

The use of an NdYAG pulsed laser for generating ultrasonic waves for NDE in resin matrix composites was investigated. A study was conducted of the use of the 1.064 micron wavelength NdYAG pulsed laser with the neat, unreinforced resin as well as graphite fiber/polymer composite specimens. In the case of the neat resins it was found that, at normal incidence, about 25 percent of the laser pulse energy was reflected at the incident surface. An attenuation coefficient for the polyimide resin, PMR-15 was determined to be approximately 5.8 np/cm. It was found in energy balance studies that graphite fiber/polymer specimens attenuate the laser beam more than do neat resins. The increase absorption is in the graphite fibers. The occurrence of laser induced surface damage was also studied. For the polymer neat resin, damage appears as pit formation over a small fraction of the pulse impact area and discoloration over a larger part of the area. A damage threshold was inferred from observed damage as a function of pulse energy. The 600 F cured PMR-15 and PMR-11 exhibit about the same amount of damage for a given laser pulse energy. The damage threshold is between 0.06 and 0.07 J/sq cm.

Kautz, Harold E.↗

Frequency-dependent dielectric analysis - Monitoring the chemistry and rheology of thermosets during cure

Frequency-dependent dielectric measurements in a curing resin sample were performed using an impedance analyzer and a permittivity sensor, to separate and measure the ionic (sigma) and dipolar (tau) mobilities, used as molecular probes of the cure reaction in the resin. The resin samples were tetraglycidyl 4,4-prime-diaminodiphenylmethane epoxy resins which included catalyzed (Hercules 3501-6) and uncatalyzed l3502 resin samples. The values of sigma and tau were used to quantitatively determine the viscosity, the degree of cure, and the T(g) of the resin. It is shown that the values of the Arrhenius and WLF constants during the cure process reflect the buildup of the crosslink network.

Kranbuehl, D.↗

Rapid Prototyping of Composite Structures

This progress report for the project Rapid Production of Composite Structures covers the period from July 14, 1997 to June 30, 1998. It will present a short overview of the project, followed by the results to date and plans for the future. The goal of this research is to provide a minimum 100x reduction in the time required to produce arbitrary, laminated products without the need for a separate mold or an autoclave. It will accomplish this by developing the science underlying the rapid production of composite structures, specifically those of carbon fiber-epoxy materials. This scientific understanding will be reduced to practice in a demonstration device that will produce a part on the order of 12" by 12" by 6". Work in the past year has focussed on developing an understanding of the materials issues and of the machine design issues. Our initial goal was to use UV cureable resins to accomplish full cure on the machine. Therefore, we have centered our materials work around whether or not UV cureable resins will work. Currently, the answer seems to be that they will not work, because UV light cannot penetrate the carbon fibers, and because no "shadow" curing seems to occur. As a result, non-UV cureable resins are being investigated. This has resulted in a change in the machine design focus. We are now looking into a "dip and place" machine design, whereby a prepreg layer would have one side coated with a curing agent, and then would be placed onto the previous layer. This would lead to cure at the interface, but not to the top of the layer. The formulation of the resins to accomplish this task at room or slightly elevated temperatures is being investigated, as is the machine design needed to apply the curing agent and then cure or partially cure the part. A final, out-of-autoclave, post-cure may be needed with this strategy, as final cure on the machine may not be possible, as it was for the initial UV cure strategy. The remainder of this report details the progress in the materials and machine design areas. Materials Development The material system must be designed to fulfill the following requirements: to reduce the time and labor requirements of typical cure cycles; to reduce the thermal stresses developed during conventional heat curing; and to develop a structure that the build sequence requires. In order to accomplish these goals, there have been parallel tracks of investigation. One area has tested photopolymerizable (ultraviolet (UV) curable) materials and combinations of these materials with standard heat curing resins. The second area has investigated resins that cure rapidly at room or low heat temperatures. The main goal of these investigations has been to identify a system that will rapidly set or cure at room temperature during a tape lay-up process and hold its structure during a post-cure cycle.

Colton, Jonathan S.↗

Development of Textile Reinforced Composites for Aircraft Structures

NASA has been a leader in development of composite materials for aircraft applications during the past 25 years. In the early 1980's NASA and others conducted research to improve damage tolerance of composite structures through the use of toughened resins but these resins were not cost-effective. The aircraft industry wanted affordable, robust structures that could withstand the rigors of flight service with minimal damage. The cost and damage tolerance barriers of conventional laminated composites led NASA to focus on new concepts in composites which would incorporate the automated manufacturing methods of the textiles industry and which would incorporate through-the-thickness reinforcements. The NASA Advanced Composites Technology (ACT) Program provided the resources to extensively investigate the application of textile processes to next generation aircraft wing and fuselage structures. This paper discusses advanced textile material forms that have been developed, innovative machine concepts and key technology advancements required for future application of textile reinforced composites in commercial transport aircraft. Multiaxial warp knitting, triaxial braiding and through-the-thickness stitching are the three textile processes that have surfaced as the most promising for further development. Textile reinforced composite structural elements that have been developed in the NASA ACT Program are discussed. Included are braided fuselage frames and window-belt reinforcements, woven/stitched lower fuselage side panels, stitched multiaxial warp knit wing skins, and braided wing stiffeners. In addition, low-cost processing concepts such as resin transfer molding (RTM), resin film infusion (RFI), and vacuum-assisted resin transfer molding (VARTM) are discussed. Process modeling concepts to predict resin flow and cure in textile preforms are also discussed.

Dexter, H. Benson↗

Integrated Thermal Structures and Materials Overview

The accomplishments of the project this viewgraph presentation summarizes (integrated thermal structures and materials) include the following: (1) Langley Research Center prepared five resins with Tgs as high as 625 F, less than 1% volatiles, moderate toughness, and low melt viscosity and sent to Boeing or Lockheed Martin; (2) Glenn Research Center prepared four resins with Tgs as high as 700 F, less than 10% volatiles, and low melt viscosity and sent to Boeing; (3) Boeing successfully fabricated 2'x2'x36 ply composites by resin infusion of stitched preforms from all NASA supplied resins; and (4) Lockheed Martin successfully fabricated 13"x14"x16 ply composites by resin transfer molding from all NASA supplied resins.

Jensen, Brian↗

Polyimide Composites Based on Asymmetric Dianhydrides (a-ODPA vs a-BPDA)

Two series of low-melt viscosity imide resins (2-15 poise at 260-280 C) were formulated from either asymmetric oxydiphthalic anhydride (a-ODPA) or asymmetric biphenyl dianhydride (a- BPDA) with 4-phenylethynyl endcap (PEPA), along with 3,4'-oxydianiline, 3,4 - methylenedianiline, 3,3 -methylenedianiline or 3,3 -diaminobenzophenone, using a solvent-free melt process. These low-melt viscosity imide resins were fabricated into polyimide/T650-35 carbon fabric composites by resin transfer molding (RTM). Composites from a-ODPA based resins display better open-hole compression strength and short beam shear strength from room temperature to 288 C than that of the corresponding a-BPDA based resins. However, due to the lower Tg s of a-ODPA based resins (265-330 C), their corresponding composites do not possess 315 C use capability while the a-BPDA based composites do. In essence, RTM 370 (T g = 370 C), derived from a-BPDA and 3,4 -ODA and PEPA, exhibits the best overall property performance at 315 C (600 F).

Chuang, Kathy C.↗

Hybrid Composite Cryogenic Tank Structure

A hybrid lightweight composite tank has been created using specially designed materials and manufacturing processes. The tank is produced by using a hybrid structure consisting of at least two reinforced composite material systems. The inner composite layer comprises a distinct fiber and resin matrix suitable for cryogenic use that is a braided-sleeve (and/or a filamentwound layer) aramid fiber preform that is placed on a removable mandrel (outfitted with metallic end fittings) and is infused (vacuum-assisted resin transfer molded) with a polyurethane resin matrix with a high ductility at low temperatures. This inner layer is allowed to cure and is encapsulated with a filamentwound outer composite layer of a distinct fiber resin system. Both inner and outer layer are in intimate contact, and can also be cured at the same time. The outer layer is a material that performs well for low temperature pressure vessels, and it can rely on the inner layer to act as a liner to contain the fluids. The outer layer can be a variety of materials, but the best embodiment may be the use of a continuous tow of carbon fiber (T-1000 carbon, or others), or other high-strength fibers combined with a high ductility epoxy resin matrix, or a polyurethane matrix, which performs well at low temperatures. After curing, the mandrel can be removed from the outer layer. While the hybrid structure is not limited to two particular materials, a preferred version of the tank has been demonstrated on an actual test tank article cycled at high pressures with liquid nitrogen and liquid hydrogen, and the best version is an inner layer of PBO (poly-pphenylenebenzobisoxazole) fibers with a polyurethane matrix and an outer layer of T-1000 carbon with a high elongation epoxy matrix suitable for cryogenic temperatures. A polyurethane matrix has also been used for the outer layer. The construction method is ideal because the fiber and resin of the inner layer has a high strain to failure at cryogenic temperatures, and will not crack or produce leaks. The outer layer serves as more of a high-performance structural unit for the inner layer, and can handle external environments.

DeLay, Thomas↗