Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Power consistency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Spacelab - A new tool for cooperative research

For work in earth orbit, the European Space Agency, ESA, in cooperation with NASA, has developed a flexible laboratory system called Spacelab, which will fit into the Space Shuttle. Spacelab will offer new possibilities for conducting research related to the behavior and properties of the neutral and ionized atmosphere. Up to 400 km altitude, the total payload weight will be in excess of 25,000 kg. The main advantages of Spacelab consist of high payload weight, power, the return of the instrumentation, and the availability of man for real-time operation of the equipment. Limitations are related to the local contamination, the restriction of mission duration to periods from one to four weeks, and limited altitudes and inclinations (for early missions). Spacelab is, therefore, not suited for many types of in-situ sensing, or for long-term monitoring. Attention is given to the proposed science program, passive observations, and chemical releases and active experiments.

Schmerling, E. R.↗

The 51.8 micron (0 3) line emission observed in four galactic H 2 regions

The (0 III) 51.8 microns line from four H II regions, M42, M17, W51 and NGC 6375A was detected. Respective line strengths are 7 x 10 to the minus 15 power, 1.0 x 10 to the minus 14 power, 2.1 x 10 to the minus 15 power and 2.6 x 10 to the minus 15 power watt cm/2. Observations are consistent with previously reported line position and place the line at 51.80 + or 0.05 micron. When combined with the 88.35 microns (0 III) reported earlier, clumping seems to be an important factor in NGC 6375A and M42 and to a lesser extent in W51 and M17. The combined data also suggest an (0 III) abundance of approximately 3 x 0.0001 sub n e' a factor of 2 greater than previously assumed.

Melnick, G.↗

Gravitational spectra from the tracking of planetary spacecraft in eccentric orbits

Two dimensional gravitational spectra are derived from simple harmonic analysis of range rate tracking data on planetary orbiters. The eccentricity of the orbit is arbitrary and results are shown to vary substantially with the aspect angle of the tracking line of sight with the orbit plane. The development for arbitrary start with stop times (with respect to periapsis) uses modified eccentricity functions evaluated by quadrature. Simulations with a point-masses model of Venus using tracking data on the Pioneer Venus Orbiter show excellent predictions of the average orbiter spectrum over one Venus day. The Venus gravitational signal should be above the tracking noise level for arc lengths longer than 40 deg (in true anomaly) about periapsis and for terms as high as 55th degree. analysis has been made of tracking residuals from a short arc fit to Mariner Mars 9 data over the Hellas Basin (using a complete 6th degree field). Results are most consistent with higher residual gravitational power than predicted from Kaula's rule for Mars.

Wagner, C. A.↗

The application of solar thermoelectric generators in near-sun missions

Future planetary near-sun missions, such as those studied for low-altitude Mercury Orbiters, introduce challenges in the selection of appropriate power sources. Study results have shown that conventional silicon solar array technology is not adequate to produce power because of expected temperatures which range from -90 C to +285 C in about 40 to 50 minutes for 16 sun eclipses/day. The solar thermoelectric generator (STG), which requires relatively high temperatures, is being considered as a replacement power source. The complete STG consists of a solar concentrator and multiple thermopiles, each containing numerous thermocouples and thermal insulation material. Articulation of the STG design configurations is required at 0.45 AU to acquire maximum incident radiation and at 0.3 AU to reduce the higher incident radiation. STG thermal input to the spacecraft as it orbits Mercury (including sun eclipses) is insignificant.

Raag, V.↗

Identification of cost effective energy conservation measures

In addition to a successful program of readily implemented conservation actions for reducing building energy consumption at Kennedy Space Center, recent detailed analyses have identified further substantial savings for buildings representative of technical facilities designed when energy costs were low. The techniques employed for determination of these energy savings consisted of facility configuration analysis, power and lighting measurements, detailed computer simulations and simulation verifications. Use of these methods resulted in identification of projected energy savings as large as $330,000 a year (approximately two year break-even period) in a single building. Application of these techniques to other commercial buildings is discussed

Bierenbaum, H. S.↗

Turbulent density fluctuations in a subsonic and transonic free jet using crossed-beam schlieren techniques

Scalar density fluctuations were measured nonintrusively in the shear layer of a 5.08-cm (2-in.) cold air jet using a crossed-beam schlieren method. Two statistics, covariance and three-dimensional spectrum function, were estimated for an exit Mach number range of 0.3 to 0.97. The density fluctuation intensity, integral scale, and eddy convection speed were calculated and compared to available data where possible. Spectra were found to change significantly in shape becoming less peaked between 3 and 9 jet diameters downstream from the orifice, but they consistently exhibited a -5/3 power law decay at 3, 6, and 9 diameters for frequencies above the peak.

Martin, R. A.↗

Military markets for solar thermal electric power systems

The Department of Defense maintains an inventory of over 1,800 MW of engine-generators 15 KW and larger, with an estimated procurement rate of over 140 MW/year. Nearly the entire requirement could be met by advanced heat engines of the types being developed as point-focussing, distributed receiver power plants. A conceptual system consisting of a heat engine which efficiently burns liquid fossil or synthetic fuels, with a 'solarization kit' for conversion to hybrid solar operation could meet existing DOD requirements for new systems which are quieter, lighter, and multi-fueled. An estimated 24 percent (33 MW/year) or more could operationally benefit from the solar option. Baseline cost projections indicate levelized energy cost goals of 210 to 120 mills/KWh (15 to 1000 KW systems). Fuel cost escalation is the major factor affecting the value of the solar option. A baseline calculation for fuel at $0.59/gal in spring, 1979, escalating at 8 percent above general inflation indicates a value of $2700/KWe for a solarization kit.

Hauger, J. S.↗

Advanced oxygen-hydrocarbon rocket engine study

The advantages and disadvantages, system performance and operating limits, engine parametric data, and technology requirements for candidate high pressure LO2/Hydrocarbon engine systems are summarized. These summaries of parametric analysis and design provide a consistent engine system data base. Power balance data were generated for the eleven engine cycles. Engine cycle rating parameters were established and the desired condition and the effect of the parameter on the engine and/or vehicle are described.

Obrien, C. J.↗

Laser-excitation technique for the measurement of absolute transition probabilities of weak atomic lines

A new technique is presented for the measurement of transition probabilities for weak allowed, intersystem, and forbidden lines. The method exploits the fact that oscillator strength is proportional to the number of stimulated absorptions and emissions produced by a narrow-band laser pulse of known energy which is in resonance with an atomic transition. The method is tested for a particular transition of Mg I with a known oscillator strength value and of appropriate magnitude. The number densities are measured using a Mach-Zehnder interferometer and the hook method for the lower level population and by measuring an absorption-equivalent width for the other. The apparatus consisted of a high-power tunable laser and a magnesium oven to produce excited Mg vapor, and a laser-plasma background continuum. The results are in good agreement with theoretical and other experimental data.

Kwong, H. S.↗

X-ray and gamma-ray upper limits for pulsed emission from radio pulsars

Results are given for an HEAO 1 search for pulsed emissions from 11 radio pulsars, in the 15 keV-11 MeV energy range. The upper limits of the Vela pulsar are found to fall below the low-energy extrapolation of the more than 50 MeV pulsed spectrum observed by the COS B satellite, and while consistent with predictions of a polar cap acceleration model, seem barely consistent with a single power-law interpolation between optical intensity and the 50 MeV intensity. High energy X-ray upper limits for seven of the ten other pulsars, which were chosen on the basis of proximity to earth, high rotational energy loss rates and short periods, are found to be only a few percent of their rotational energy losses, assuming a moment of inertia, an emission solid angle, and a pulse duty cycle, that are all similar to the high energy X-ray duty cycle of the Crab pulsar. These upper limits are below the corresponding fraction for the Crab pulsar in the cases of the Vela pulsar, PSR 1929+10 and PSR 1642-03.

Knight, F. K.↗

Particle size distributions in Saturn's rings from Voyager 1 radio occultation

Information on Saturn ring particle sizes obtained with the Voyager 1 ring occultation experiment is discussed. The theory underlying the determination of the particle size distribution is presented, including differential extinction and inversion of the scattered signal. Experimental observations and results for the observed spectra, differential cross sections, suprameter and sub- to suprameter size distributions are presented. The size and mass distributions both cut off sharply at about 4-5 m; the mass distribution peaks over the 3-4 m size range for four ring system features at 1.35, 1.51, 2.01, and 2.12 Saturn radii. A power-law type model is consistent with the data over a limited size range of 0.01 to 1 m. The fractional contribution of the suprameter particles to the microwave opacity for the four features appears to be about 1/3, 1/3, 2/3, and 1, respectively, and their cumulative surface mass per unit area are about 11, 16, 41, and 132 g/sq cm if the particles are solid water ice.

Marouf, E. A.↗

HEAO 3 observations of the Crab pulsar

The Crab pulsar (PSR 0531+21) is the only pulsar which has been observed throughout almost the entire electromagnetic spectrum from 0.5 keV to over 2000 GeV. In general, the emission from the Crab nebula and its pulsar has been remarkably constant in time (except for the pulsations). However, several recent observations, especially of gamma-ray line emission, indicate possible time variations. The present investigation is concerned with the data obtained with the HEAO C-1 experiment. The data have been studied with the hope of finding information regarding a number of questions, taking into account the existence of line emission from the pulsar, the variation of the shape of the light curve with time, and the spectral variations as a function of pulsar phase. The spectrum of the total phase-averaged pulsed emission is found to be consistent with a single power-law spectrum from 50 keV to 10 MeV.

Mahoney, W. A.↗

Radio occultation by Saturn's rings - Observations of structure and particle size with Voyager 1

Voyager 1 radio occultation study of Saturn's rings gives detailed information regarding the rings' radial structure and particle sizes. Structure within the rings is mapped to a radial resolution of few hundred m in the tenuous parts of ring C and the Cassini Division, and few km over most of ring A. Fine resolution profiles reveal extremely sharp edges, very narrow gaps, and a host of wave phenomena. Particle size distributions obtained from occultation data within several ring regions are roughly consistent with an inverse cube power law with upper size cutoff in the 5 to 10 m radius range.

Marouf, E. A.↗

Static investigation of two STOL nozzle concepts with pitch thrust-vectoring capability

A static investigation of the internal performance of two short take-off and landing (STOL) nozzle concepts with pitch thrust-vectoring capability has been conducted. An axisymmetric nozzle concept and a nonaxisymmetric nozzle concept were tested at dry and afterburning power settings. The axisymmetric concept consisted of a circular approach duct with a convergent-divergent nozzle. Pitch thrust vectoring was accomplished by vectoring the approach duct without changing the nozzle geometry. The nonaxisymmetric concept consisted of a two dimensional convergent-divergent nozzle. Pitch thrust vectoring was implemented by blocking the nozzle exit and deflecting a door in the lower nozzle flap. The test nozzle pressure ratio was varied up to 10.0, depending on model geometry. Results indicate that both pitch vectoring concepts produced resultant pitch vector angles which were nearly equal to the geometric pitch deflection angles. The axisymmetric nozzle concept had only small thrust losses at the largest pitch deflection angle of 70 deg., but the two-dimensional convergent-divergent nozzle concept had large performance losses at both of the two pitch deflection angles tested, 60 deg. and 70 deg.

Mason, M. L.↗

Drag measurements of blunt stores tangentially mounted on a flat plate at supersonic speeds

An investigation has been conducted in the Langley Unitary Plan Wind Tunnel to measure the drag of blunt stores (hemispherical noses and afterbodies) tangentially mounted in various arrays on a flat plate at nominal Mach numbers of 1.60, 1.90, 2.16,and 2.86 and at a nominal Reynolds number of 2X10 to the 6th power per foot. The arrays consisted of two and three stores mounted in lateral, tandem, or staggered arrangements. The relative position of the stores in the arrays was varied while the drag of only one store was measured to determine the effect of spacing on the store drag. Store-on-store interference was determined by comparing the drag of a single store with the drag of the store in an array. The results indicate virtually all arrangements and spacings which were tested had favorable store-on-store interference (drag reduction) across the Mach number range. Tabulated data, schlieren photographs, and shadowgraphs are included.

Wilcox, Floyd J., Jr.↗

Design, development and evaluation of Stanford/Ames EVA prehensors

Space Station operations and maintenance are expected to make unprecedented demands on astronaut EVA. With Space Station expected to operate with an 8 to 10 psi atmosphere (4 psi for Shuttle operations), the effectivness of pressurized gloves is called into doubt at the same time that EVA activity levels are to be increased. To address the need for more frequent and complex EVA missions and also to extend the dexterity, duration, and safety of EVA astronauts, NASA Ames and Stanford University have an ongoing cooperative agreement to explore and compare alternatives. This is the final Stanford/Ames report on manually powered Prehensors, each of which consists of a shroud forming a pressure enclosure around the astronaut's hand, and a linkage system to transfer the motions and forces of the hand to mechanical digits attached to the shroud. All prehensors are intended for attachment to a standard wrist coupling, as found on the AX-5 hard suit prototype, so that realistic tests can be performed under normal and reduced gravity as simulated by water flotation.

Leifer, Larry J.↗

Experimental Vibration Damping Characteristics of the Third-stage Rotor of a Three-stage Transonic Axial-flow Compressor

Rotor blade aerodynamic damping is experimentally determined in a three-stage transonic axial flow compressor having design aerodynamic performance goals of 4.5:1 pressure ratio and 65.5 lbm/sec weight flow. The combined damping associated with each mode is determined by a least squares fit of a single degree of freedom system transfer function to the nonsynchronous portion of the rotor blade strain gage output power spectra. The combined damping consists of the aerodynamic damping and the structural and mechanical damping. The aerodynamic damping varies linearly with the inlet total pressure for a given corrected speed, weight flow, and pressure ratio while the structural and mechanical damping is assumed to remain constant. The combined damping is determined at three inlet total pressure levels to obtain the aerodynamic damping. The third-stage rotor blade aerodynamic damping is presented and discussed for the design equivalent speed with the stator blades reset for maximum efficiency. The compressor overall preformance and experimental Campbell diagrams for the third-stage rotor blade row are also presented.

Newman, Frederick A.↗