Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Plasma materials processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Simulation of Liquid Lithium Divertor Geometry Using SOLPS-ITER

Here, plasma-facing component (PFC) geometries are evaluated for a Fusion Nuclear Science Facility (FNSF) design to find solutions that are compatible with flowing liquid lithium components while satisfying requirements from the perspective of plasma and neutral particle transport. Flowing liquid metal (LM) divertor systems offer important advantages due to continual regeneration of the surface material, but may require modifications from standard optimized tokamak divertor designs. Scrape Off Layer Plasma Simulator for the International Thermonuclear Experimental Reactor (SOLPS-ITER) simulations are used to compare standard vertical target, open, and balanced baffled geometries. It is found that the open geometry offers little control of neutral particles and has narrow operating windows where the divertor fluxes can be lowered to acceptable levels, while maintaining the required upstream density. The addition of neutral baffles allows greater control over the divertor conditions with less impact on the upstream density. The divertor neutral pressure in the baffled geometry is slightly higher than the open divertor, but not as large with a vertical target. A first-pass coupling of the SOLPS solution with sheath and implantation/erosion models to compute the lithium emission shows that the lithium is largely confined to the near-surface region due to the small ionization mean free path and large main ion flow toward the surface. The lithium source was varied by three orders of magnitude. At the highest rate, when the sourced lithium approaches the level of the main ion recycling flux, a high core lithium concentration (~10%) is observed with only moderate power dissipation to affect the divertor plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Formate-Induced Dissolution and Reprecipitation of a Copper Electrocatalyst during Electrochemical CO 2 Reduction Reaction

Catalyst size, morphology, and crystal structure play crucial roles in determining the activity and selectivity of electrochemical CO 2 reduction reactions, which are known to change during the reaction process. A comprehensive understanding of how, when, and why these parameters evolve under operational conditions is essential for developing stable, efficient, and selective catalysts. In this study, we reveal that formate, one of the reaction products, contributes to the degradation of copper catalysts through a ligand-assisted dissolution mechanism. Utilizing in situ electrochemical atomic force microscopy and ex-situ scanning and transmission electron microscopies, we observed a significant reduction in the size of copper nanoparticles, which decreased from over 30 nm to less than 10 nm in diameter within 60 min of CO 2 RR. The temporal production of formate correlated with the particle size changes. Furthermore, analysis of the electrolyte using inductively coupled plasma optical emission spectroscopy confirmed the dissolution of copper nanoparticles. Control experiments involving various reaction products (H 2 , CO, and HCOO – ) demonstrated that formate significantly promotes copper dissolution, thereby highlighting its role in the ligand-assisted dissolution mechanism of copper electrocatalysts. In conclusion, our findings provide critical insights into copper catalyst behavior during electrochemical CO 2 reduction, facilitating the design of more resilient and effective electrocatalysts.

Catalysts↗
DOE OSTI2026

Vapor phase deposition of alumina on interior surfaces of tritium storage containers

Efficient tritium management and containment are critical challenges for nuclear fusion. To mitigate issues related to permeation into structural materials and isotopic exchange with protium, permeation barriers must be applied to the nonplanar internal surfaces of tritium handling components. In this study, we developed an atomic layer deposition (ALD) system to deposit films on canisters used to store and transport tritium. Growth conditions for deposition of Al 2 O 3 were mapped spatially along the length of a canister using silicon witness samples characterized by ellipsometry, atomic force microscopy, and x-ray reflectivity (XRR). We identified ALD process windows for growth at temperatures between 100 and 140 °C. Furthermore, we compared films grown on our Si witness samples to those grown on polished stainless steel 316 (SS316). X-ray photoelectron spectroscopy indicates two distinct chemical states for the alumina, while XRR confirms that the overall growth rate is similar to the 1.1 Å/cycle that we observed on the Si witness samples.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Potential Applications of Quantum Computing at Los Alamos National Laboratory, v0.3.0

Since the scientific revolution in the 16th and 17th centuries, the process of scientific discovery has followed an iterative feedback process of observation, hypothesis development and testing with physical experiments, which is widely referred to as the scientific method. This process remained largely unchanged until the middle of the 20th century, when the emergence of digital computers empowered scientist to build and inspect detailed simulations of physical phenomena. Over the last century, computational tools have transformed modern approaches to scientific discovery by enabling fast and affordable hypothesis testing before physical experiments are conducted, shown in Figure 1-1. Some notable examples include: global climate forecasts to understand how the environment may change over decades [130]; modeling the behavior of plasma to design fusion reactors [59]; and understanding the behavior of molecules in biological processes [161, 223].

36 MATERIALS SCIENCE↗
DOE OSTI2021

Durability of plasma sprayed Thermal Barrier Coatings with controlled properties part Ⅱ: Effects of geometrical curvature

The present investigation elucidates the effects of substrate curvature on the durability of Air Plasma Sprayed (APS) Thermal Barrier Coatings (TBCs). Traditionally, planar disk specimens are utilized in Furnace Cycle Testing (FCT). In most cases, delamination is initiated at the disk's free edge and then propagates along the TBC-bond coat interface. However, in turbine components (e.g., blades/vanes), they lack significant free edges and the coatings are deposited on non-flat surfaces of varying radii of curvature. These geometrical discrepancies imply significant differences in the stress states as compared to planar disk specimens. Therefore, the part geometry inevitably affects the TBC failure mechanisms in the turbine system, and consequently influences TBC durability. Nevertheless, these effects have not been fully explored in the past, despite the anecdotal knowledge which suggests the leading edge of turbine blades to be one of the most common failure/spallation locations. Here in this study, representative TBC systems were deposited onto superalloy disks with flat substrate and rods with curved substrate. The experimental results from FCT suggest TBC durability on rods is significantly lower than when sprayed on disks. Furthermore, the durability of TBCs on rods appears to increase with higher porosity, which is contradictory to reported trends for TBCs on disks. In addition, the effects of various bond coats are not consistent with those observed in disks. To clarify the underlying effects of curved geometries, detailed stress analyses were performed. They revealed a state of thermal stresses which is unique to curved geometries. It was found that TBC on rods experience tensile radial stresses as well as tensile hoop stresses during the cooling. These stresses result in a complex interplay in failure processes in rods, which explains the different observed trends in the durability from those obtained with disks.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Accelerating Embedding Potential Optimization by Reconstructing the Pseudo-Valence Electron Density

Density functional embedding theory (DFET) enables use of electronic structure methods with higher accuracy than density functional theory in a local region, with applications thus far ranging from (photo/electro)catalysis to reactions in solution. DFET partitions a large collection of atoms into smaller groups that interact via a shared embedding (interaction) potential V emb , determined via functional optimization. The optimized effective potential (OEP) process used to optimize V emb is time-consuming and becomes a computational bottleneck due to sharp, oscillating features of V emb near nuclei. Here, similar to pseudopotential theory, by reconstructing electron densities used in the OEP process from smoother pseudo-valence-only (PVO) electron densities as proxies for total densities of the full system and subsystems, we can retain accuracy in the embedded electronic structure calculations while potentially reducing the overhead of V emb construction, within the projector augmented-wave (PAW) formalism. We explore three different chemical reactions as exemplars to test PVO–DFET, namely, H 2 dissociative adsorption on a Cu(111) surface, H 2 O adsorption on a Pt(111) surface, and aqueous [Ca 2+ –SO 4 2– ] ion-pair formation. The PVO approximation works well for all three systems with minimal loss of accuracy (∼10–70 meV error relative to the original exact-derivative (ED) approach) while accelerating V emb generation for the Cu and Pt systems respectively by 20× and 5×. Given proper numerical convergence parameters, the spatial distributions of differences between PVO- and ED-based V emb outside the core regions are small, explaining the exceptional agreement between the two approaches. Finally, we anticipate that this more efficient PVO–DFET approximation will be useful whenever computation of V emb is much more expensive than subsequent embedded high-level electron correlation calculations.

approximation↗
DOE OSTI2020

U 3 Si 2 and UO 2 composites densified by spark plasma sintering for accident-tolerant fuels

This work reports the synthesis and characterization of the U 3 Si 2 and UO 2 composites sintered by spark plasma sintering (SPS) with controlled microstructures for accident-tolerant fuel application. The U 3 Si 2 and UO 2 composites with different silicide and oxide ratios were synthesized by SPS at temperatures from 1000 to 1300 °C for 5 minutes. The microstructure and phase composition of the SPS densified composite fuels were characterized with scanning electron microscopy, X-ray diffraction (XRD), and energy dispersed spectroscopy (EDS). A systematic study of the thermal and mechanical properties was conducted using microhardness testing and laser flash apparatus, along with oxidation resistance measurements using thermogravimetric analysis (TGA). The results show that the synthesis of composite fuels can be achieved with a 90% theoretical density (TD) at 1000 °C and over 95% TD when sintered at 1300 °C. XRD and EDS results confirmed that the dominant phases in the composites are U 3 Si 2 and UO 2 . Improved physical density generally leads to improved hardness, fracture toughness, thermal diffusivity, and onset temperature during the oxidation process. U 3 Si 2 was found to play a dominant role in determining the mechanical and oxidation properties of the composite fuels, whereas UO 2 had a more important impact on controlling the thermal diffusivity of the composites. The composite with 50 wt% UO 2 sintered at 1300 °C displayed the onset oxidation temperature of 500 °C by dynamic oxidation testing using TGA at a ramp degree of 10 °C/min. The composite also achieved a high fracture toughness of ~3.5 MPa m ½ . Finally, these results highlight the potential of composite fuel forms densified by SPS with simultaneously enhanced fissile element density, fracture toughness, thermal transport properties, and oxidation resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Opacity Table Generation

Radiation opacity is a key property of material systems which describes the absorption and scattering of photons. Such processes are an important part of energy transport, diagnostics, and astrophysical phenomena. Recent experiments in iron opacity and continuum lowering have sparked renewed interest in and careful vetting of opacity models. Even within the local thermodynamic equilibrium approximation, opacity varies over a large parameter space: material, temperature, density, and energy. Opacity tables that span wide regimes of this parameter space are of prime importance to radiation-hydrodynamics codes. Accurate opacity calculations cannot be achieved inline during a radiation hydrodynamics simulation since they involve accounting for all possible electron transitions of all important atomic states of a thermal ensemble. Livermore’s current framework utilizes precalculated tables at many densities, temperatures, and energies. Last year, the opacity theory team completed an L2 milestone concerning the development of a new code, Opus, which served the dual purpose of creating a modern code infrastructure and version control as well as the basis for training new members of that team, a critical need as key members near or are passed retirement. For the current L2 milestone, we exercised and validated Opus on three elements: boron, carbon, and nitrogen, which have few enough electrons to allow a careful convergence study over many input parameters. Here, we report on the production of new tables, show their convergence with respect to important parameters, state some of their limitations, and document a mostly automated production process. In this section, we address the milestone completion criteria, found on the title page and the subsection headings. In section 2, we validate Opus against Tycho and compare with TabOp and Atomic. Section 3 details some of the physics implemented in Opus and relevant to this report. We then cover details of the density-temperature grid in section 4 and do a spectral comparison between different parameter settings and different codes in section 5. After summarizing these results in section 6, we give instructions how to run the opacity table scripts in appendix A and document the scripts and input/output files in appendix B.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Deep potential molecular dynamics simulations of ion-enhanced etching of silicon by atomic chlorine

The continued development of plasma-assisted processing techniques requires a fundamental understanding of plasma-surface interactions. Molecular dynamics (MD) simulations have been employed to complement experimental studies and better understand the properties of such systems. Recently, machine learning (ML) methods have enabled the development of ab initio-based interatomic potentials, which can be generalized to complex combinations of multiple atom types. In this work, we use ML potentials developed using the Deep Potential Molecular Dynamics (DeepMD) framework to provide a model of ion-enhanced etching of Si by Cl atoms. We demonstrate the importance of proper selection of the training data set to the accuracy of the DeepMD model and compare our results to MD results using empirical potentials, as well as to experimental measurements. Exposure of undoped Si at 300 K to thermal Cl atoms yields a steady-state Cl coverage of 1.25 monolayers, which is slightly lower than the value obtained in previous experimental studies. Predictions of Si etch yields by simultaneous Cl atom and Ar + ion impacts as a function of ion energy, neutral to ion flux ratio, and angle of incidence of the ions are in reasonably good agreement with classical MD results and experimental measurements. Finally, etch yields and SiCl x mixed layer thicknesses during simultaneous bombardment of the Si(100) surface by Cl atoms and Cl + ions are in good agreement with experimental data. In conclusion, the present work is a necessary condition for the extension of the DeepMD procedure to more complex systems of interest in plasma-surface interactions.

Artificial neural networks↗
DOE OSTI2020

Physics and technology considerations for the deuterium–tritium fuel cycle and conditions for tritium fuel self sufficiency

The tritium aspects of the DT fuel cycle embody some of the most challenging feasibility and attractiveness issues in the development of fusion systems. The review and analyses in this paper provide important information to understand and quantify these challenges and to define the phase space of plasma physics and fusion technology parameters and features that must guide a serious R&D in the world fusion program. We focus in particular on components, issues and R&D necessary to satisfy three 'principal requirements': (1) achieving tritium self-sufficiency within the fusion system, (2) providing a tritium inventory for the initial start-up of a fusion facility, and (3) managing the safety and biological hazards of tritium. A primary conclusion is that the physics and technology state-of-the-art will not enable DEMO and future power plants to satisfy these principal requirements. We quantify goals and define specific areas and ideas for physics and technology R&D to meet these requirements. A powerful fuel cycle dynamics model was developed to calculate time-dependent tritium inventories and flow rates in all parts and components of the fuel cycle for different ranges of parameters and physics and technology conditions. Dynamics modeling analyses show that the key parameters affecting tritium inventories, tritium start-up inventory, and tritium self-sufficiency are the tritium burn fraction in the plasma (f b ), fueling efficiency (η f ), processing time of plasma exhaust in the inner fuel cycle (t p ), reactor availability factor (AF), reserve time (tr) which determines the reserve tritium inventory needed in the storage system in order to keep the plant operational for time t r in case of any malfunction of any part of the tritium processing system, and the doubling time (t d ). Results show that η f f b > 2% and processing time of 1–4 h are required to achieve tritium self-sufficiency with reasonable confidence. For η f f b = 2% and processing time of 4 h, the tritium start-up inventory required for a 3 GW fusion reactor is ~11 kg, while it is <5 kg if η f f b = 5% and the processing time is 1 h. To achieve these stringent requirements, a serious R&D program in physics and technology is necessary. The EU-DEMO direct internal recycling concept that carries fuel directly from the plasma exhaust gas to the fueling systems without going through the isotope separation system reduces the overall processing time and tritium inventories and has positive effects on the required tritium breeding ratio (TBR R ). A significant finding is the strong dependence of tritium self-sufficiency on the reactor availability factor. Simulations show that tritium self-sufficiency is: impossible if AF < 10% for any η f f b , possible if AF > 30% and 1% ≤ η f f b ≤ 2%, and achievable with reasonable confidence if AF > 50% and η f f b > 2%. These results are of particular concern in light of the low availability factor predicted for the near-term plasma-based experimental facilities (e.g. FNSF, VNS, CTF), and can have repercussions on tritium economy in DEMO reactors as well, unless significant advancements in RAMI are made. There is a linear dependency between the tritium start-up inventory and the fusion power. The required tritium start-up inventory for a fusion facility of 100 MW fusion power is as small as 1 kg. Since fusion power plants will have large powers for better economics, it is important to maintain a 'reserve' tritium inventory in the tritium storage system to continue to fuel the plasma and avoid plant shutdown in case of malfunctions of some parts of the tritium processing lines. But our results show that a reserve time as short as 24 h leads to unacceptable reserve and start-up inventory requirements. Therefore, high reliability and fast maintainability of all components in the fuel cycle are necessary in order to avoid the need for storing reserve tritium inventory sufficient for continued fusion facility operation for more than a few hours. The physics aspects of plasma fueling, tritium burn fraction, and particle and power exhaust are highly interrelated and complex, and predictions for DEMO and power reactors are highly uncertain because of lack of experiments with burning plasma. Fueling by pellet injection on the high field side of tokamak has evolved to be the preferred method to fuel a burning plasma. Extrapolation from the DIII-D penetration scaling shows fueling efficiency expected in DEMO to be <25%, but such extrapolations are highly uncertain. The fueling efficiency of gas in a reactor relevant regime is expected to be extremely poor and not very useful for getting tritium into the core plasma efficiently. Gas fueling will nonetheless be useful for feedback control of the divertor operating parameters. Extensive modeling has been carried out to predict burn fraction, fueling requirements, and fueling efficiency for ITER, DEMO, and beyond. The fueling rate required to operate Q = 10 ITER plasmas in order to provide the required core fueling, helium exhaust and radiative divertor plasma conditions for acceptable divertor power loads was calculated. If this fueling is performed with a 50–50 DT mix, the tritium burn fraction in ITER would be ~0.36%, which is too low to satisfy the self-sufficiency conditions derived from the dynamics modeling for fusion reactors. Extrapolation to DEMO using this approach would also yield similarly low burn fraction. Extensive analysis presented shows that specific features of edge neutral dynamics in ITER and fusion reactors, which are different from present experiments, open possibilities for optimization of tritium fueling and thus to improve the burn fraction. Using only tritium in pellet fueling of the plasma core, and only deuterium for edge density, divertor power load and ELM control results in significant increase of the burn fraction to 1.8–3.6%. These estimates are performed with physics models whose results cannot be fully validated for ITER and DEMO plasma conditions since these cannot be achieved in present tokamak experiments. Thus, several uncertainties remain regarding particle transport and scenario requirements in ITER and DEMO. The safety standard requirements for protection of the public and release guidelines for tritium have been reviewed. General safety approaches including minimizing tritium inventories, reducing tritium permeation through materials, and decontaminating material for waste disposal have been suggested.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Multi-modal dynamic radiography using short-pulse laser-generated probe beams

Radiography is an important tool for the interrogation of dynamic experiments in the fields of dynamic properties of materials, and in condensed matter, high explosive, and high-energy-density physics. Multi-modal radiography advances the hypothesis that combining the information delivered by multiple radiographic modalities can lead to more constrained (improved) “reconstruction” of the scene than can be obtained from a single probe. We identify four modalities: multi-probe, time sequence, multi-view, and multi-messenger. Multi-probe radiography is a promising candidate for a next-generation dynamic radiographic facility. High-energy X-rays are the most frequently used probe for dynamic radiography, although recent developments show the utility of proton (pRad), electron (eRad), and neutron probe beams. Because each probing species interacts with material in the radiographic scene through quantitatively different mechanisms, each returns independent information about the scene, which can add extra constraints to the reconstruction process. How to conduct detailed, quantitative “co-analysis” of multiple data streams remains an area of active research. Multi-beam, short-pulse, laser-generated probes offer sufficient dose, an appropriate spectrum, and appropriate spatio-temporal resolution to produce high-quality dynamic radiographs. This paper reports on technology development to advance the state of the art of multi-modal/multi-probe radiography and the pursuit of both deterministic and inferential (AI/ML assisted) co-analysis methodologies to produce more constrained reconstructions from multi-modal data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Tritium Transport Modeling at the Pore Scale in Ceramic Breeder Materials Using TMAP8

Fusion reactors depend on the blanket material to breed and release tritium at the same rate or faster than it is consumed by the fusion reaction. Cellular ceramic breeders (CCBs) are dense materials that can maintain a high tritium breeding ratio while promoting tritium release because of highly connected pores. Assessing the tritium breeding capabilities of these materials requires a combination of extensive experimental and modeling efforts. In this work, we develop and calibrate a multiphysics model of tritium transport. This novel model accounts for ceramic and pore diffusion, trapping and detrapping, and several surface reactions at the pore surface. We perform a sensitivity analysis and calibrate the model by comparing its predictions against experimental measurements of deuterium absorption. The calibrated model is then used to model tritium absorption in samples with different pore microstructures to investigate the effect of pore interconnectivity on tritium absorption. The model is part of the development of the multiscale, multiphysics framework for tritium transport [i.e., the Tritium Migration Analysis Program (TMAP8)], which is itself built on top of the finite-element multiphysics framework multiphysics object-oriented simulation environment (MOOSE). This study demonstrates some of TMAP8’s capabilities and is the first step toward assessing the tritium breeding capabilities of ceramic breeder material designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Design and Testing of a Prototype Eddy Current Actuated Valve for the ITER Shattered Pellet Injection System

Reliably mitigating disruptions is essential for ITER to meet its long-term operational research plan without damage to the in-vessel components. Currently, the shattered pellet injection (SPI) technique is the most effective radiator of thermal energy and has been chosen for the baseline disruption mitigation system (DMS) for ITER. The SPI process uses cryogenic temperatures to desublimate material into the barrel of a pipe gun forming a solid cylindrical pellet. Pellets for ITER will initially be hydrogen and hydrogen-neon mixtures. Once formed, pellets are dislodged and accelerated using high-pressure gas (40-60 bar) delivered by a fast-opening valve. The solenoid valves currently used for SPI experiments will not operate in an ITER environment due to the large background magnetic field. An ITER prototype fast-opening valve, called a flyer plate valve (FPV), has been designed and has undergone a wide range of testing. The FPV operates by pulsing current through a pancake coil that is closely coupled with a ``flyer plate.'' The flyer plate is an aluminum plate in which eddy currents are generated creating a repulsive force from the pancake coil. The force generated in the flyer plate rapidly lifts the valve tip off the seat and delivers a pulse of gas to the rear of the pellet, breaking it free from the barrel and accelerating the pellet downstream to its intended target. The design of the valve has been iterated on over the lifetime of this project, as the DMS for ITER shifted from massive gas injection (MGI) to SPI. The most recent design has been tested, and operational ranges have been mapped. The valve must survive 3000+ cycles in an ITER-like magnetic field. The principal functional requirement of this valve is to reliably dislodge and accelerate hydrogen (or H-Ne mixture) pellets into ITER. The valve was mated with an ITER SPI test stand and has been shown to be capable of launching pellets reliably. The valve and power supply design will be discussed in this article, along with the various testing setups used to determine the feasibility of this valve for use on ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Characterization of a 1D-imaging high-energy x-ray backlighter driven by the National Ignition Facility Advanced Radiographic Capability laser

Plastic deformation of samples compressed to Mbar pressures at high strain rates at the National Ignition Facility (NIF) forms the basis of ongoing material strength experiments in conditions relevant to meteor impacts, geophysics, armor development, and inertial confinement fusion. Hard x-ray radiography is the primary means of measuring the evolution of these samples, typically employing a slit-collimated high-Z microdot driven by the NIF laser to generate >40 keV x rays [E. Gumbrell et al., Rev. Sci. Instrum. 89, 10G118 (2018) and C. M. Huntington et al., Rev. Sci. Instrum. 89, 10G121 (2018)]. Alternatively, a dysprosium “micro-flag” target driven by the Advanced Radiographic Capability laser (~2 kJ, 10 ps) can deliver significantly higher spatiotemporal resolution [M. P. Hill et al., Rev. Sci. Instrum. 92, 033535 (2021)], especially in high-opacity samples. Here, initial experiments revealed problematic brightness and spectral gradients from this source, but by radiographing a set of diamond-turned, 105 µm-thick Pb test objects and supported by simulations using the 3D Monte Carlo code GEANT4, these geometry-dependent gradients across the field of view are quantified and mitigation strategies are assessed. In addition to significantly enhancing the modulation transfer function compared to the existing system, image stacking from multiple layers of image plate is shown to almost double the signal to noise ratio that will reduce uncertainties in future dynamic strength experiments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Techniques for studying materials under extreme states of high energy density compression

The properties of materials under extreme conditions of pressure and density are of key interest to a number of fields, including planetary geophysics, materials science, and inertial confinement fusion. In geophysics, the equations of state of planetary materials, such as hydrogen and iron, under ultrahigh pressure and density provide a better understanding of their formation and interior structure [Celliers et al., “Insulator-metal transition in dense fluid deuterium,” Science 361, 677–682 (2018) and Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)]. The processes of interest in these fields occur under conditions of high pressure (100 GPa–100 TPa), high temperature (>3000 K), and sometimes at high strain rates (>103 s−1) depending on the process. With the advent of high energy density (HED) facilities, such as the National Ignition Facility (NIF), Linear Coherent Light Source, Omega Laser Facility, and Z, these conditions are reachable and numerous experimental platforms have been developed. To measure compression under ultrahigh pressure, stepped targets are ramp-compressed and the sound velocity, measured by the velocity interferometer system for any reflector diagnostic technique, from which the stress-density of relevant materials is deduced at pulsed power [M. D. Knudson and M. P. Desjarlais, “High-precision shock wave measurements of deuterium: Evaluation of exchange-correlation functionals at the molecular-to-atomic transition,” Phys. Rev. Lett. 118, 035501 (2017)] and laser [Smith et al., “Equation of state of iron under core conditions of large rocky exoplanets,” Nat. Astron. 2, 591–682 (2018)] facilities. To measure strength under high pressure and strain rates, experimenters measure the growth of Rayleigh–Taylor instabilities using face-on radiography [Park et al., “Grain-size-independent plastic flow at ultrahigh pressures and strain rates,” Phys. Rev. Lett. 114, 065502 (2015)]. The crystal structure of materials under high compression is measured by dynamic x-ray diffraction [Rygg et al., “X-ray diffraction at the national ignition facility,” Rev. Sci. Instrum. 91, 043902 (2020) and McBride et al., “Phase transition lowering in dynamically compressed silicon,” Nat. Phys. 15, 89–94 (2019)]. Medium range material temperatures (a few thousand degrees) can be measured by extended x-ray absorption fine structure techniques, Yaakobi et al., “Extended x-ray absorption fine structure measurements of laser-shocked V and Ti and crystal phase transformation in Ti,” Phys. Rev. Lett. 92, 095504 (2004) and Ping et al., “Solid iron compressed up to 560 GPa,” Phys. Rev. Lett. 111, 065501 (2013), whereas more extreme temperatures are measured using x-ray Thomson scattering or pyrometry. This manuscript will review the scientific motivations, experimental techniques, and the regimes that can be probed for the study of materials under extreme HED conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2001

Fusion for Space Propulsion

There is little doubt that humans will attempt to explore and develop the solar system in this century. A large amount of energy will be required for accomplishing this. The need for fusion propulsion is discussed. For a propulsion system, there are three important thermodynamical attributes: (1) The absolute amount of energy available, (2) the propellant exhaust velocity, and (3) the jet power per unit mass of the propulsion system (specific power). For human exploration and development of the solar system, propellant exhaust velocity in excess of 100 km/s and specific power in excess of 10 kW/kg are required. Chemical combustion can produce exhaust velocity up to about 5 km/s. Nuclear fission processes typically result in producing energy in the form of heat that needs to be manipulated at temperatures limited by materials to about 2,800 K. Using the energy to heat a hydrogen propellant increases the exhaust velocity by only a factor of about two. Alternatively the energy can be converted into electricity which is then used to accelerate particles to high exhaust velocity. The necessary power conversion and conditioning equipment, however, increases the mass of the propulsion system for the same jet power by more than two orders of magnitude over chemical system, thus greatly limits the thrust-to-weight ratio attainable. The principal advantage of the fission process is that its development is relatively mature and is available right now. If fusion can be developed, fusion appears to have the best of all worlds in terms of propulsion - it can provide the absolute amount, the propellant exhaust velocity, and the high specific jet power. An intermediate step towards pure fusion propulsion is a bimodal system in which a fission reactor is used to provide some of the energy to drive a fusion propulsion unit. The technical issues related to fusion for space propulsion are discussed. The technical priorities for developing and applying fusion for propulsion are somewhat different from those for terrestrial electrical power generation. Thus fusion schemes that are initially attractive for electrical power generation might not necessarily be attractive also for propulsion and vice versa, though the underlying fusion science and engineering enjoy much overlap. Parallel efforts to develop these qualitatively differently fusion schemes for the two applications could benefit greatly from each other due to the synergy in the underlying physics and engineering. Pulsed approaches to fusion have not been explored to the same degree as steady-state or long-pulse approaches to fusion in the fusion power research program. The concerns early on were several. One was that the pulsed power components might not have the service lifetimes meeting the requirements of a practical power generating plant. Another was that, for many pulsed fusion schemes, it was not clear whether the destruction of hardware per pulse could be minimized or eliminated or recycled to such an extent as to make economical electrical power generation feasible, Significant development of the underlying pulsed power component technologies have occurred in the last two decades because of defense and other energy requirements. The state of development of the pulsed power technologies are sufficiently advanced now to make it compelling to visit or re-visit pulsed fusion approaches for application to propulsion where the cost of energy is not so demanding a factor as in the case of terrestrial power application. For propulsion application, the overall mass of the fusion system is the critical factor. Producing fusion reactions require extreme states of matter. Conceptually, these extreme states of matter are more readily realizable in the pulsed states, at least within appropriate bounds, than in the steady states. Significant saving in system mass may result in such systems. Magnetic fields are effective in confining plasma energy, whereas inertial compression is an effective way of heating and containing the plasma. Intensive research in developing magnetic energy containment and inertial plasma compression are being pursued in distinctively different fusion experiments in the terrestrial fusion power program. Fusion schemes that attempt to combine the favorable attributes of these two aspects into one single integrated fusion scheme appear to have benefits that are worth exploring for propulsion application.

Thio, Y. C. Francis↗
DOE OSTI2026

Innovative laser-based methods for monitoring fuel retention in ITER

This paper addresses the challenge of tritium inventory management in ITER and future fusion reactors, highlighting the importance of accurate tritium measurement and its spatial distribution within the vacuum vessel. Given ITER’s operational constraints, especially the limit on tritium retention, precise measurement is essential for both safety and regulatory compliance. To tackle these questions, the paper presents the T-monitor diagnostic system developed by Forschungszentrum Jülich, which uses Laser-Induced Desorption (LID) in combination with Diagnostic Residual Gas Analysis (DRGA) to measure hydrogen isotope concentrations on the surface of divertor tiles. The system integrates a high-power laser, advanced optical components, and a Fast Scanning Mirror Unit (FSMU) for accurate laser spot positioning with rapid response. Designed to measure in situ tritium retention, the diagnostic provides high-resolution spatial mapping, vital for evaluating detritiation strategies. The laser heating process increases the divertor surface temperature to 1600 K within the laser spot, promoting hydrogen isotope desorption. Accurate measurements require the precise control of laser parameters, including pulse duration and spot size, with a target relative accuracy of 20%. The optical design includes both in-vessel and ex-vessel components, such as durable high-reflectivity mirrors made of gold and copper, selected not only for their infrared performance but also for their transmission of visible wavelengths for observation purposes. To protect optical components from contamination, a pneumatic shutter is used.

Hydrogen isotopes↗
DOE OSTI2025

An Evaluation of Actinide Reactivity with CO 2 , O 2 , and O 2 /He Gases using Inductively Coupled Plasma Tandem Mass Spectrometry: Application to Simultaneous Measurement of 241 Am/ 241 Pu Ratios in Unseparated Complex Matrices

Accurate actinide measurements are critical within the field of nuclear science. Traditional methods for actinide quantification require time-consuming sample processing prior to analysis. There is a need for rapid analytical techniques that still maintain a high degree of accuracy. In this work, actinide reactivity was assessed for multiple oxygen-containing reaction gases using quadrupole inductively coupled plasma tandem mass spectrometry (Q-ICP-MS/MS) to evaluate actinide analysis in complex sample matrices without analyte-matrix separation. A novel method was developed to measure 241 Am/ 241 Pu in complex sample matrices using O 2 /He reaction gas with no matrix removal or analyte pre-concentration. This inline method reduces matrix-derived polyatomic interferences that complicate traditional ICP-MS analyses by mass-shifting to 241 Am 16 O + and 241 Pu 16 O 2 + , allowing Am and Pu to be mass separated for simultaneous analysis. While mass shifting is efficient, a small portion of Am + (<1.3%) and Pu + (<1.4%) react to from AmO 2 + and PuO + , respectively. Therefore, a mass balance approach was used, in combination with reactivity determined from 242 Pu and 243 Am standard solutions, to correct for residual 241 PuO + and 241 AmO 2 + . The method was validated by measuring 241 Am/ 241 Pu in Pu isotope standards CRM-136 and CRM-137 (separated in March/April 1970 and February 2022, respectively) in both neat solutions and complex matrices containing diluted soil (NIST SRM 2711a, >1000 µg·g -1 ). Method detection limits of 15.9 and 9.6 fg·g -1 were determined for 241 Am and 241 Pu, respectively, and 241 Am/ 241 Pu ratios were measured with accuracies within <3.5%. In conclusion, this work presents the first direct analysis of 241 Am/ 241 Pu in unseparated complex matrices, advancing capabilities for rapid actinide measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗