Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle phenomena”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Hypervelocity impact effects on solar cells

One of the space hazards of concern is the problem of natural matter and space debris impacting spacecraft. This phenomena has been studied since the early sixties and a methodology has been established to determine the relative abundance of meteoroids as a function of mass. As the mass decreases, the probability of suffering collisions increases, resulting in a constant bombardment from particles in the sub-micron range. The composition of this 'cosmic dust' is primarily Fe, Ni, Al, Mg, Na, Ca, Cr, H, O, and Mn. In addition to mechanical damage, impact velocities greater than 5 k m/sec can produce shock induced ionization effects with resultant surface charging and complex chemical interactions. The upper limit of the velocity distribution for these particles is on the order of 70 km/sec. The purpose of this work was to subject samples from solar power arrays to debris flux typical of what would be encountered in space, and measure the degradation of the panels after impact.

Rose, M. Frank↗
NASA NTRS2008

NASA Marshall Impact Testing Facility Capabilities Applicable to Lunar Dust Work

The Impact Testing Facility at Marshall Space Flight Center has several guns that would be of use in studying impact phenomena with respect to lunar dust. These include both ballistic guns, using compressed gas and powder charges, and hypervelocity guns, either light gas guns or an exploding wire gun. In addition, a plasma drag accelerator expected to reach 20 km/s for small particles is under development. Velocity determination and impact event recording are done using ultra-high-speed cameras. Simulation analysis is also available using the SPHC hydrocode.

Evans, Steven W.↗
DOE OSTI2022

Optimization of quasi-symmetric stellarators with self-consistent bootstrap current and energetic particle confinement

Quasi-symmetry can greatly improve the confinement of energetic particles and thermal plasma in a stellarator. The magnetic field of a quasi-symmetric stellarator at high plasma pressure is significantly affected by the bootstrap current, but the computational cost of accurate stellarator bootstrap calculations has precluded use inside optimization. Here, a new efficient method is demonstrated for optimization of quasi-symmetric stellarator configurations such that the bootstrap current profile is consistent with the geometry. The approach is based on the fact that all neoclassical phenomena in quasi-symmetry are isomorphic to those in axisymmetry. Therefore, accurate formulas for the bootstrap current in tokamaks, which can be evaluated rapidly, can be applied also in stellarators. The deviation between this predicted parallel current and the actual parallel current in the magnetohydrodynamic equilibrium is penalized in the objective function, and the current profile of the equilibrium is included in the parameter space. Quasi-symmetric configurations with significant pressure are thereby obtained with self-consistent bootstrap current and excellent confinement. In a comparison of fusion-produced alpha particle confinement across many stellarators, the new configurations have significantly lower alpha energy losses than many previous designs.

Landreman, M. (ORCID:000000027233577X)↗
DOE OSTI2025

Review: Recent advances of ToF-SIMS for environmental analysis and imaging

Background: Time-of-flight secondary ion mass spectrometry (ToF-SIMS) is a powerful surface analysis technique, initially developed and applied in inorganic materials and semiconductors. In past decades, ToF-SIMS has attracted more attention in its analysis capabilities of organic materials, with increased applications in biology, medical, and health development. It has also become a versatile and effective tool in environmental analysis due to its high mass resolution, mass accuracy, and depth profiling. Results: In this review, we first give an overview of the principle of ToF-SIMS and follow with recent ToF-SIMS applications in exemplary environmental study cases, including atmospheric aerosol, soil, water, plant, and organic solvent analysis. Moreover, sample preparation techniques are summarized in relation to corresponding environmental applications. Specifically, we call attention to ToF-SIMS investigations showcasing studies in surface chemical compositions, images, and depth profile analysis. These findings emphasize the important role of interfacial chemistry in environmental processes and provide valuable insights into dynamic processes, such as chemical transformation, particle formation, plant biology, and microbial inspired biotechnology development. The mass spectral imaging results acquired by ToF-SIMS offer a deeper understanding of intermediate stages and transient phases for environmental specimens. Significance: In situ and operando imaging offer new possibilities in studying phenomena in real time with high spatial resolution. Furthermore, it is anticipated that more research groups will use ToF-SIMS in environmental research given recent advances in measurement capabilities and surging needs in chemical mapping of complex analytes and systems.

Aerosol↗
NASA NTRS1972

Review of magnetic field observations.

Recent observations in previously unexplored regions of the magnetosphere, particularly in the polar-cusp region, compliment and reinforce emphasis on particle access to the plasma sheet via the polar neutral points. Significant distortions of the geomagnetic field in the polar-cusp region suggest field-aligned currents at large geocentric distances which can be related to low-altitude polar-cap phenomena. Studies of the microstructure of the field reversal region of the plasma sheet embedded in the geomagnetic tail suggest a periodic structure of more complexity than earlier assumed simplified single neutral-line models.

Ness, N. F.↗
NASA NTRS1989

Plasma waves in the magnetotail of Uranus

Plasma wave phenomena observed during the Voyager 2 passing through the magnetotail of Uranus after its encounter with the planet on January 24, 1986 are described. The location of the wave events, their probable mode of propagation, and their association with various plasma and charged particle observations are presented. It was found that the most remarkable magnetotail plasma waves were inside the distance of about 23 Uranus radii, with an additional event occurring between about 48 and 56 Uranus radii. The frequency of these magnetotail plasma waves was found to be below about 100 Hz, extending down to the 10-Hz lower frequency limit of the receiver. The shape of the spectrum and the location of the wave activity near the boundary layer suggest that these waves may be similar to broadband electrostatic waves observed in similar regions of the earth's magnetotail.

Kurth, W. S.↗
NASA NTRS2001

An Investigation of Surge in a High-Speed Centrifugal Compressor Using Digital PIV

Compressor stall is a catastrophic breakdown of the flow in a compressor, which con lead to a loss of engine power, large pressure transients in the inlet/nacelle, and engine flameout. The implementation of active or passive strategies for controlling rotating stall and surge can significantly extend the stable operating range of a compressor without substantially sacrificing performance. It is crucial to identify the dynamic changes occurring in the flow field prior to rotating stall and surge in order to control these events successfully. Generally, pressure transducer measurements are made to capture the transient response of a compressor prior to rotating stall. In this investigation, Digital Particle Imaging Velocimetry (DPIV) is used in conjunction with dynamic pressure transducers to capture transient velocity and pressure measurements simultaneously in the nonstationary flow field during compressor surge. DPIV is an instantaneous, planar measurement technique that is ideally suited for studying transient flow phenomena in highspeed turbomachinery and has been used previously to map the stable operating point flow field in the diffuser of a high-speed centrifugal compressor. Through the acquisition of both DPIV images and transient pressure data, the time evolution of the unsteady flow during surge is revealed.

Wernet, Mark P.↗
DOE OSTI2022

Summary of Working Group 3: Laser and High-Gradient Structure-Based Acceleration

Accelerating particles at high gradients with high efficiencies is essential for reduction of size and cost of future accelerators for science and industry. This includes a future multi-TeV e+e- collider for particle, free-electron lasers for basic energy sciences and national security, industrial accelerators for energy and environmental applications, and accelerators for other applications. One way to achieve this is to use advanced externally-powered structures, both laser and RF driven. Working Group 3 (WG3) discussed novel accelerating structures with new geometries, new materials, frequencies from microwave to THz and optical spectrum, and operating conditions from room temperature to cryogenic. Presentations included recent advances in understanding RF breakdown and multipactor phenomena at different frequencies and materials, and other physics limitations to the accelerating gradient. Other relevant topics, such as developing high-gradient photoinjectors, high-efficiency RF power sources, and RF structures for a potential muon collider were discussed also. More details on each of the WG3 topics can be found in the articles published in these proceedings.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Aging of Self-Assembled Lead Halide Perovskite Nanocrystal Superlattices: Effects on Photoluminescence and Energy Transfer

Excitonic coupling, electronic coupling, and cooperative interactions in self-assembled lead halide perovskite nanocrystals were reported to give rise to a red-shifted collective emission peak with accelerated dynamics. Here we report that similar spectroscopic features could appear as a result of the nanocrystal reactivity within the self-assembled superlattices. This is demonstrated by studying CsPbBr 3 nanocrystal superlattices over time with room-temperature and cryogenic micro-photoluminescence spectroscopy, X-ray diffraction, and electron microscopy. It is shown that a gradual contraction of the superlattices and subsequent coalescence of the nanocrystals occurs over several days of keeping such structures under vacuum. As a result, a narrow, low-energy emission peak is observed at 4 K with a concomitant shortening of the photoluminescence lifetime due to the energy transfer between nanocrystals. When exposed to air, self-assembled CsPbBr 3 nanocrystals develop bulk-like CsPbBr 3 particles on top of the superlattices. At 4 K, these particles produce a distribution of narrow, low-energy emission peaks with short lifetimes and excitation fluence-dependent, oscillatory decays. Overall, the aging of CsPbBr 3 nanocrystal assemblies dramatically alters their emission properties and that should not be overlooked when studying collective optoelectronic phenomena nor confused with superfluorescence effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Ultrahigh-precision Compton polarimetry at 2 GeV

Here we report a high precision measurement of electron beam polarization using Compton polarimetry. The measurement was made in experimental Hall A at Jefferson Lab during the CREX experiment in 2020. A precision of dP/P = 0.36% was achieved detecting the back-scattered photons from the Compton scattering process. This is the highest precision in a measurement of electron beam polarization using Compton scattering ever reported, surpassing the ground-breaking measurement from the SLD Compton polarimeter. Such precision reaches the level required for the future flagship measurements to be made by the MOLLER and SoLID Experiments.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Implications of Non-Bingham Rheology

One of the key challenges now facing the US Department of Energy (DOE) is the fate of radioactive waste remaining from World War II and the Cold War which is stored underground in tanks some 75 feet in diameter and over 30 feet tall. Over time, the waste has segmented into multiple layers with sludges and slurries at the bottom with salt crust layers often at the top and liquid in between. DOE’s current official baseline plans call for remaining sludges and slurries to be removed from the tanks and converted into a more stable glass waste form. Minimizing worker exposure to radiation drives DOE to use slurry processing techniques to suspend, mobilize, transport, mix, and process the waste. Therefore, a clear and quantitative understanding of Hanford waste rheology is essential for the success of the DOE mission. Historically much of the waste has been characterized using Eugene Bingham’s model more than a century old that provides a straight line fit to higher shear rate data with the intercept suggesting a yield stress and the slope providing the consistency. Yet, Bingham fits overestimate the shear stress at a given shear rate for low to intermediate shear rates, exactly the range of shear rates typically encountered in pipe flow, where shear rates peak along the pipe wall and vanish in the center. This model produces a fictitious yield stress for some of the wastes that do not exhibit yield phenomena. While over estimating the yield stress may be prudent, safe, and conservative for some applications (e.g., pump sizing to ensure that pumps can handle yield stresses), over estimating the rheology may be inaccurate and non-conservative for other applications (e.g., eroding settled particle beds). Therefore, this paper evaluates the slurry rheology of Hanford and Savannah River wastes using a more modern rheological model that fits the full range of experimental data. Although a bias has been recognized and alternative models proposed, the magnitude of this bias and the implications for tank waste have only been qualitatively suggested. The purpose of this paper is to evaluate quantitatively implications of the poor quality of fit between a Bingham model for rheology and experimental data at modest shear rates. We first demonstrate the magnitude of the bias between the data and the Bingham extrapolation. We then evaluate quantitatively the velocity profile under laminar conditions. This analysis shows that the bias may be large (hundreds of percent or more) at modest shear rates and that modest shear rates dominate pipe velocity profiles.

Rheology, Radioactive waste↗
NASA NTRS1977

Active experiments in modifying spacecraft potential: Results from ATS-5 and ATS-6

Instruments on ATS-5 and ATS-6 were operated to study the phenomena of spacecraft charging. The ion engine neutralizers were operated in attempts to modify the spacecraft potentials. The neutralizer on ATS-5 is a hot filament emitting electrons, while the neutralizer on ATS-6 is a low energy plasma bridge. The diagnostics used were particle detectors, counting electrons and protons as a function of energy. Operations were conducted in daylight and eclipse. This report describes the processing data from these and other operations. Only preliminary analysis of some of this data has been carried out, with the following results: (1) electron emission does not perturb the status of a low potential satellite by more than 50 volts, (2) emission of a low energy plasma does not change low potentials by more than a few volts, (3) when ATS-6 enters eclipse in the presence of a high energy plasma, the neutralizer suppresses any rise in (within a few volts resolution), (4) when the electron emitter on ATS-5 is operated, it serves to discharge negative potentials from thousands to hundreds of volts.

Olsen, R.↗
NASA NTRS1993

Modeling of microgravity combustion experiments

Modeling plays a vital role in providing physical insights into behavior revealed by experiment. The program at the University of Illinois is designed to improve our understanding of basic combustion phenomena through the analytical and numerical modeling of a variety of configurations undergoing experimental study in NASA's microgravity combustion program. Significant progress has been made in two areas: (1) flame-balls, studied experimentally by Ronney and his co-workers; (2) particle-cloud flames studied by Berlad and his collaborators. Additional work is mentioned below. NASA funding for the U. of Illinois program commenced in February 1991 but work was initiated prior to that date and the program can only be understood with this foundation exposed. Accordingly, we start with a brief description of some key results obtained in the pre - 2/91 work.

Buckmaster, John↗
NASA NTRS2010

Evolution of Interplanetary Shocks and their CME Drivers

Shock-driving coronal mass ejections (CMEs) constitute the most energetic phenomena in the heliosphere. The shocks can be identified in a number of ways based on remote-sensing and in situ observations. Type II radio bursts are the earliest indicators of shocks that accelerate electrons to energies up to -10 keV. Solar energetic particle (SEP) events are always accompanied by long wavelength type II bursts indicating that the same shock accelerates ions and electrons. A recent investigation involving a large number of interplanetary (IP) shocks revealed that about 35% of them do not produce type II bursts (radio quiet, RQ) or SEPs. Comparison of the RQ shocks with the radio loud (RL) ones revealed some interesting results such as: (1) the lack of evidence for blast waves,(2) energetic particle enhancement in the shock front in -20% of RQ shocks, and (3) determination of the difference between the RQ and RL shocks in terms of the different kinematic properties of the associated CMEs. On the other hand the shock properties measured at I AU are not too different for the RQ and RL cases. This can be attributed to the interaction with the IP medium, which seems to erase the difference. Implications of this evolution for the geoeffectiveness is also discussed.

Gopalswamy, Natchimuthuk↗
DOE OSTI2022

Quantum enhanced metrology in the search for fundamental physical phenomena

These notes summarize lectures given at the 2019 Les Houches summer school on Quantum Information Machines. They describe and review an application of quantum metrology concepts to searches for ultralight dark matter. In particular, for ultralight dark matter that couples as a weak classical force to a laboratory harmonic oscillator, quantum squeezing benefits experiments in which the mass of the dark matter particle is unknown. This benefit is present even if the oscillatory dark matter signal is much more coherent than the harmonic oscillator that it couples to, as is the case for microwave frequency searches for dark matter axion particles.

Lehnert, Konrad↗
NASA NTRS1995

Internal and surface phenomena in metal combustion

Combustion of metals has been widely studied in the past, primarily because of their high oxidation enthalpies. A general understanding of metal combustion has been developed based on the recognition of the existence of both vapor-phase and surface reactions and involvement of the reaction products in the ensuing heterogeneous combustion. However, distinct features often observed in metal particle combustion, such as brightness oscillations and jumps (spearpoints), disruptive burning, and non-symmetric flames are not currently understood. Recent metal combustion experiments using uniform high-temperature metal droplets produced by a novel micro-arc technique have indicated that oxygen dissolves in the interior of burning particles of certain metals and that the subsequent transformations of the metal-oxygen solutions into stoichiometric oxides are accompanied with sufficient heat release to cause observed brightness and temperature jumps. Similar oxygen dissolution has been observed in recent experiments on bulk iron combustion but has not been associated with such dramatic effects. This research addresses heterogeneous metal droplet combustion, specifically focusing on oxygen penetration into the burning metal droplets, and its influence on the metal combustion rate, temperature history, and disruptive burning. A unique feature of the experimental approach is the combination of the microgravity environment with a novel micro-arc Generator of Monodispersed Metal Droplets (GEMMED), ensuring repeatable formation and ignition of uniform metal droplets with controllable initial temperature and velocity. The droplet initial temperatures can be adjusted within a wide range from just above the metal melting point, which provides means to ignite droplets instantly upon entering an oxygen containing environment. Initial droplet velocity will be set equal to zero allowing one to organize metal combustion microgravity experiments in a fashion similar to usual microgravity liquid fuel droplet combustion studies. In addition, the internal compositions of rapidly quenched metal particles will be analyzed using SEM technique. Such compositions are similar to those existing during the combustion and provide new insight on metal combustion processes. The results of this experimental work will be used to model the fundamental mechanisms of metal combustion. Preliminary experimental results on Al and Zr particle combustion at normal gravity are discussed here.

Dreizin, Edward L.↗