Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical constants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Millimeter-wave passive ultra-compact imaging technology for synthetic vision & mobile platforms

Substantial technical progress was made on all of the three high-risk subsystems of this program. The subsystems include dielectric antenna, G-band receiver, and electro-optic image processor. Progress is approximately on-schedule for both the receiver and the electro-optic processor development, while greater than anticipated challenges have been discovered in the dielectric antenna development. Much of the information in this report was covered in greater detail in the One-Year Review Meeting held at TTC on 22 February 1996. The performance goals of the dielectric antenna project are: Scan Angle -- 20 deg. desired; Loss -- 6 dB end to end (3 dB average); Frequency -- 206-218 GHz (6% bandwidth); Beam width -- 0.25 deg.; and Length -- 12 inches. The scan angle requirement was chosen to satisfy the needs of aircraft pilots. This requirement, coupled with the presently limited bandwidth processors (1 GHz state-of-the-art and 12 GHz in development in this program) forces the antenna to be dielectric (high scan angle air-filled waveguide-based antennas would be too lossy and their performance would vary too much as a function of frequency). A high dielectric constant (e.g., 10) was initially chosen for the dielectric material. This choice lead to the following fabrication challenges: total thickness variation (TTV) tolerance is 1 micrometer; coupler spacing tolerance is 1 micrometer; width tolerance is larger, but unknown, and the surfaces must have mirror finish. Also of importance is the difficulty in obtaining raw materials that satisfy the overall length requirement of 12 inches while simultaneously satisfying the above specifications.

Olsen, Randall↗
NASA NTRS1994

A revised analysis of micron-sized particles detected near Saturn by the Voyager 2 plasma wave instrument

The impulsive noise that the plasma wave and radio astronomy instruments detected during the Voyager 2 swing by Saturn was attributed to dust grains striking the spacecraft. This report presents a reanalysis of the dust impacts recorded by the plasma wave instrument using an improved model for the response of the electric antenna to dust impacts. The fundamental assumption used in this analysis is that the voltage induced on the antenna is proportional to the mass of the impacting grain. Using the above assumption and the antenna response constants used at Uranus and Neptune, the following conclusions can be reached. The primary dust distribution consists of a 'disk' of particles that coincides with the equator plane and has a north-south thickness of 2-Delta zeta = 962 km. A less dense 'halo' with a north-south thickness of 2-Delta zeta = 3376 km surrounds the primary distribution. The dust particle sizes are of the order of 10 microns, assuming a mass density of 1 g/cu cm. The corresponding particle masses are of the order of 10(exp -9) g, and maximum number densities are of the order of 10(exp -2)/cu m. Most likely, the G ring is the dominate source since the particles were observed very close to that ring, namely at 2.86 R(sub S). Other sources, like nearby moons, are not ruled out especially when perturbations due to electromagnetic forces are included. The calculated optical depth differs by about a factor of 2 from photometric studies. The current particle masses, radii, and the effective north-south thickness of the particle distribution are larger than what Gurnett et al. (1983) reported by about 2, 1, and 1 orders of magnitude, respectively. This is attributed to the fact that the collection coefficient used in this study is smaller than what was used in Gurnett et al.'s earlier publication.

Tsintikidis, D.↗
NASA NTRS2001

Projected Impact of Climate Change on the Energy Budget of the Arctic Ocean by a Global Climate Model

The annual energy budget of the Arctic Ocean is characterized by a net heat loss at the air-sea interface that is balanced by oceanic heat transport into the Arctic. The energy loss at the air-sea interface is due to the combined effects of radiative, sensible, and latent heat fluxes. The inflow of heat by the ocean can be divided into two components: the transport of water masses of different temperatures between the Arctic and the Atlantic and Pacific Oceans and the export of sea ice, primarily through Fram Strait. Two 150-year simulations (1950-2099) of a global climate model are used to examine how this balance might change if atmospheric greenhouse gases (GHGs) increase. One is a control simulation for the present climate with constant 1950 atmospheric composition, and the other is a transient experiment with observed GHGs from 1950 to 1990 and 0.5% annual compounded increases of CO2 after 1990. For the present climate the model agrees well with observations of radiative fluxes at the top of the atmosphere, atmospheric advective energy transport into the Arctic, and surface air temperature. It also simulates the seasonal cycle and summer increase of cloud cover and the seasonal cycle of sea-ice cover. In addition, the changes in high-latitude surface air temperature and sea-ice cover in the GHG experiment are consistent with observed changes during the last 40 and 20 years, respectively. Relative to the control, the last 50-year period of the GHG experiment indicates that even though the net annual incident solar radiation at the surface decreases by 4.6 W(per square meters) (because of greater cloud cover and increased cloud optical depth), the absorbed solar radiation increases by 2.8 W(per square meters) (because of less sea ice). Increased cloud cover and warmer air also cause increased downward thermal radiation at the surface so that the net radiation into the ocean increases by 5.0 Wm-2. The annual increase in radiation into the ocean, however, is compensated by larger increases in sensible and latent heat fluxes out of the ocean. Although the net energy loss from the ocean surface increases by 0.8 W (per square meters), this is less than the interannual variability, and the increase may not indicate a long-term trend. The seasonal cycle of heat fluxes is significantly enhanced. The downward surface heat flux increases in summer (maximum 2 of 19 W per square meters or 23% in June) while the upward heat flux increases in winter (maximum of 16 W per square meters or 28% in November). The increased downward flux in summer is due to a combination of increases in absorbed solar and thermal radiation and smaller losses of sensible and latent heat. The increased heat loss in winter is due to increased sensible and latent heat fluxes, which in turn are due to reduced sea-ice cover. On the other hand, the seasonal cycle of surface air temperature is damped, as there is a large increase in winter temperature but little change in summer.

Miller, James R.↗
NASA NTRS2002

Earth Observing-1 Advanced Land Imager: Imaging Performance On-Orbit

This report analyzes the on-orbit imaging performance of the Advanced Land Imager (ALI) on the Earth Observing-1 satellite. The pre-flight calibrations are first summarized. The methods used to reconstruct and geometrically correct the image data from this push-broom sensor are described. The method used here does not refer to the position and attitude telemetry from the spacecraft. Rather, it is assumed that the image of the scene moves across the focal plane with a constant velocity, which can be ascertained from the image data itself. Next, an assortment of the images so reconstructed is presented. Color images sharpened with the 10-m panchromatic band data are shown, and the algorithm for producing them from the 30-m multispectral data is described. The approach taken for assessing spatial resolution is to compare the sharpness of features in the on-orbit image data with profiles predicted on the basis of the pre-flight calibrations. A large assortment of bridge profiles is analyzed, and very good fits to the predicted shapes are obtained. Lunar calibration scans are analyzed to examine the sharpness of the edge-spread function at the limb of the moon. The darkness of the space beyond the limb is better for this purpose than anything that could be simulated on the ground. From these scans, we find clear evidence of scattering in the optical system, as well as some weak ghost images. Scans of planets and stars are also analyzed. Stars are useful point sources of light at all wavelengths, and delineate the point-spread functions of the system. From a quarter-speed scan over the Pleiades, we find that the ALI can detect 6th magnitude stars. The quality of the reconstructed images verifies the capability of the ALI to produce Landsat-type multi spectral data. The signal-to-noise and panchromatic spatial resolution are considerably superior to those of the existing Landsat sensors. The spatial resolution is confirmed to be as good as it was designed to be.

ALI (ADVANCED LAND IMAGER)↗
NASA NTRSDate not supplied

Trade-Offs of Simplified Versus Comprehensive Representation of Mineralogy When Studying Dust Impacts on Earth’s Climate Systems

The intensity and direction of dust impacts on Earth’s climate systems depend on mineral composition. For example, the presence or absence of a few percent of iron oxides in dust will determine if dust is warming or cooling the atmosphere. Similarly, feldspar will enhance ice cloud formation, while acid gases in the atmosphere will react on the surface of dust calcite limiting acid rain. Still, most climate models use a simplified representation of dust mineralogy. They assume a fixed composition at emission which stays invariant during transport and removal. Such simplification assumes spatially and temporally constant physical and chemical properties of dust, and appears to provide satisfactory results when comparing some properties with observations. The trade-off is their lack of spatial gradients, which will fail to induce circulation, cloud and precipitation changes. The two reasons to omit mineral variations are the uncertainty of current atlases of soil mineral composition in arid regions, and, more practically, an improved runtime efficiency. The former reason is losing ground with the recent launch (July 2022) of a dedicated mission (NASA/JPL EMIT) to retrieve global soil mineralogy of dust sources at high spatial resolution. While the EMIT science team is finalizing a satisfactory global map of mineral composition of dust sources, we analyzed the interaction of dust mineralogy on radiation and its impact on the fast temperature response using different representations of mineral composition from detailed and spatially varying to simplified and globally uniform, assuming different hematite contents and methods to calculate optical properties. Our results show that resolving dust mineralogy reduces dust absorption, and results in improved agreement with observation-based single scattering albedo (SSA), radiative fluxes from CERES (the Clouds and the Earth’s Radiant Energy System), and land surface temperature from CRU (Climatic Research Unit), compared to the baseline bulk dust model version. It also results in distinct radiative impacts on Earth’s climate over North Africa. From our 19-year simulation, we will show that it leads to a reduction of over 50% in net downward radiation at top of atmosphere (TOA) across the Sahara and an approximately 20% reduction over the Sahel. We will explain how the surface temperature response affects the monsoon flow from the Gulf of Guinea. Interestingly, we find similar results by simply fixing the hematite content of dust to a globally uniform value of 0.9% by volume. We will discuss the underlying reasons for such results and show that they may be unrelated to the distribution of soil mineralogy. Still, an accurate representation of soil mineralogy is necessary to better understand dust impacts on the Earth’s climate systems.

dust impacts↗
NASA NTRS1990

Numerical simulations of the rebound shock model for solar spicules

Using time-dependent numerical simulations, the proposed rebound shock mechanism for spicules has been examined. At temperatures above a critical value, T(c), the radiation is characteristic of the conditions in the optically thin corona and near optically thin transition region. When T less than T(c), the atmosphere has a radiative cooling time, tau(rad) characteristic of chromosphere. The spicule is initiated with a quasi-impulsive force in the low chromosphere, which drives a train of upward propagating rebound shocks along the rigid magnetic flux tube. These shocks then move the transition region upward. The material below the displaced transition region has temperatures and densities similar to those of spicules when T(c) = 20,000 K or more and tau(rad) = 500 s or more, but not when T(c) = 10,000 K, and probably not when tau(rad) = 100 s. For all the cases where the cross sectional area diverges rapidly with height, the upward velocity of the transition region is less than that of spicules. Moreover, the maximum height is less than that of average spicules. Taller, higher velocity spicules result when the magnetic field cross sectional area is constant. In all cases, the rebound shock mechanism produces substantial motions and temperature and density variations in chromospheric and transition region material. It is suggested that this may be a partial explanation for the continuous dynamic state of the lower solar atmosphere.

Sterling, Alphonse C.↗
NASA NTRS2001

Measurements of Aerosol Vertical Profiles and Optical Properties during INDOEX 1999 Using Micro-Pulse Lidars

Micro-pulse lidar systems (MPL) were used to measure aerosol properties during the Indian Ocean Experiment (INDOEX) 1999 field phase. Measurements were made from two platforms: the NOAA ship RN Ronald H. Brown, and the Kaashidhoo Climate Observatory (KCO) in the Maldives. Sunphotometers were used to provide aerosol optical depths (AOD) needed to calibrate the MPL. This study focuses on the height distribution and optical properties (at 523 nm) of aerosols observed during the campaign. The height of the highest aerosols (top height) was calculated and found to be below 4 km for most of the cruise. The marine boundary layer (MBL) top was calculated and found to be less than 1 km. MPL results were combined with air mass trajectories, radiosonde profiles of temperature and humidity, and aerosol concentration and optical measurements. Humidity varied from approximately 80% near the surface to 50% near the top height during the entire cruise. The average value and standard deviation of aerosol optical parameters were determined for characteristic air mass regimes. Marine aerosols in the absence of any continental influence were found to have an AOD of 0.05 +/- 0.03, an extinction-to-backscatter ratio (S-ratio) of 33 +/- 6 sr, and peak extinction values around 0.05/km (near the MBL top). The marine results are shown to be in agreement with previously measured and expected values. Polluted marine areas over the Indian Ocean, influenced by continental aerosols, had AOD values in excess of 0.2, S-ratios well above 40 sr, and peak extinction values approximately 0.20/km (near the MBL top). The polluted marine results are shown to be similar to previously published values for continental aerosols. Comparisons between MPL derived extinction near the ship (75 m) and extinction calculated at ship-level using scattering measured by a nephelometer and absorption using a PSAP were conducted. The comparisons indicated that the MPL algorithm (using a constant S-ratio throughout the lower troposphere) calculates extinction near the surface in agreement with the ship-level measurements only when the MBL aerosols are well mixed with aerosols above. Finally, a review of the MPL extinction profiles showed that the model of aerosol vertical extinction developed during an earlier INDOEX field campaign (at the Maldives) did not correctly describe the true vertical distribution over the greater Indian Ocean region. Using the average extinction profile and AOD obtained during marine conditions, a new model of aerosol vertical extinction was determined for marine atmospheres over the Indian Ocean. A new model of aerosol vertical extinction for polluted marine atmospheres was also developed using the average extinction profile and AOD obtained during marine conditions influenced by continental aerosols.

Welton, Ellsworth J.↗
NASA NTRS2019

Quantifying the Evolution of Molecular Production Rates of Comet 21P/Giacobini–Zinner with iSHELL/NASA-IRTF

This paper presents results from our molecular characterization of comet 21P/Giacobini–Zinner during its 2018 apparition. We followed the comet during four observing runs, for a total of eight nights. The high-resolution spectra of 21P were acquired using iSHELL—the near-infrared high-resolution immersion echelle spectrograph on NASA/IRTF (Maunakea, Hawaii). We detected many cometary emission lines across four customized iSHELL settings in the (2.9–5.2) μm range. CO abundances relative to water displayed a relatively constant behavior during the observing campaign, suggesting a possible correlation between the outgassing of water and CO. While CO mixing ratios in 21P are consistent with the reference median value for Jupiter family comets (JFCs), ethane was depleted relative to the reference median value for JFCs, except for one observing run (August 8 and 9) in which ethane appeared overabundant. We consider several possible causes: an ethane outburst, decreasing outgassing of water, or a seasonal effect owing to nucleus rotation. In the pre-perihelion runs, methanol was overabundant compared with the reference median value for JFCs, however it decreased steadily to a depleted value during 21P’s post-perihelion phase, suggesting a possible seasonal effect. We report 3σ upper limits for acetylene, formaldehyde, ammonia, and methane. The ratios of our measured 3σ upper limits for acetylene and detections of hydrogen cyanide are consistent with the depletion of C2 relative to CN in 21P observed at optical wavelengths. This result confirms that 21P is depleted in the carbon-chain primary volatile responsible for C2.

Faggi, S.↗
NASA NTRS2019

Quantifying the Evolution of Molecular Production Rates of Comet 21P/Giacobini–Zinner with iSHELL/NASA-IRTF

This paper presents results from our molecular characterization of comet 21P/Giacobini-Zinner during its 2018 apparition. We followed the comet during four observing runs, for a total of 8 nights. The high-resolution spectra of 21P were acquired using iSHELL - the near-IR high resolution immersion echelle spectrograph on NASA/IRTF (Mauna Kea, Hawaii). We detected many cometary emission lines across four customized iSHELL settings in the (2.9 – 5.2) μm range. CO abundances relative to water displayed a relatively constant behavior during the observing campaign, suggesting a possible correlation between the outgassing of water and CO. While CO mixing ratios in 21P are consistent with the reference median value for Jupiter Family comets (JFCs), ethane was depleted relative to the reference median value for JFCs, excepting one observing run (8th and 9th Aug) in which ethane appeared overabundant. We consider several possible causes: an ethane outburst, decreasing outgassing of water, or a seasonal effect owing to nucleus rotation. In the pre-perihelion runs, methanol was overabundant compared with the reference median value for JFCs, however it decreased steadily to a depleted value during 21P’s post-perihelion phase, suggesting a possible seasonal effect. We report 3-s upper limits for acetylene, formaldehyde, ammonia and methane. The ratios of our measured 3-s upper limits for acetylene and detections of hydrogen cyanide are consistent with the depletion of C2 relative to CN in 21P observed at optical wavelengths. This result confirms that 21P is depleted in the carbon chain primary volatile responsible for C2 production.

Faggi S.↗
NASA NTRS1989

An investigation of a mathematical model of an optically pumped Ti(3+):Al2O3 laser system

During the last several years, solid state lasers were developed that have the potential for meeting rigorous performance requirements for space-based remote sensing of the atmosphere. In order to design a stable and efficient laser and to understand the effect on laser output of changes in the physical and design parameters, an understanding of the development of the dynamical processes of the laser is necessary. Typically, the dynamical processes in a laser system are investigated via rate equations describing the evolution of the occupancy in the electronic levels and of the photon density in the laser cavity. There are two approaches to this type of study. Most often, for the sake of simplicity, the spatial variations of the dynamic variables in the laser system are disregarded and the mathematical model consists of a system of first order nonlinear ordinary differential equations (ODE). The second approach is to take into account both spatial and temporal variations in the dynamic variables in the laser cavity. The resulting model consists of a first order semilinear system of partial differential equations (PDE). The model which was studied was studied was generic in the sense that it was a four-level laser system, but the parameters used in the numerical study were specific to Titanium-doped sapphire. For simplicity, a constant, spatially uniform pumping scheme was considered. In addition, a simplification of the model was made so that it treats a single lasing wavelength with a narrow bandwidth. The purpose was to investigate both versions of the mathematical model and to determine whether the numerical solutions are similar both qualitatively and quantitatively. The systems of ordinary differential equations were solved numerically using a Runge-Kutta-Fehlberg algorithm which was very efficient for typical values of the physical parameters. A numerical scheme, based on the Modified Euler method, for computing solutions to the system of partial differential equations was developed and implemented. The PDE model was solved numerically at the expense of greatly increased computer time.

Roberts, Lila F.↗
NASA NTRS1985

Continuous prediction of Spartan visibility from Orbiter over modeled free-flight mission

Orbital operations in the neighborhood of other satellites or free-flying objects need the ability to see and detect such objects optically. This ability depends primarily on the brightness of the object relative to other sources present. The present analysis and computational procedure provides a means for predicting the visual brightness of a satellite when viewed from a nearby satellite in the same orbit. It is designed specifically for estimating the brightness of Spartan free-flyers from the STS Orbiters which release and later retrieve them, but the basic methods are applicable to other satellite-to-satellite visibility prediction problems. The Spartan reflector model defined herein is illuminated both by direct solar radiation and by the earth (albedo), producing a model source of defined directional intensity. The intensity in the Orbiter direction (along orbit) yields the desired maximum range directly. The required geometric and photometric calculations involve a number of angles in space, which are readily computed from the basic directions defining their sides. The time-dependent directions are determined by straightforward calculation from fundamental relationships and constants.

King, J. C.↗
NASA NTRS1994

Chemical transitions for interstellar C2 and CN in cloud envelopes

Observations were made of absorption from CH, C2, and CN toward moderately reddened stars in Sco, OB2, Ceo OB3, and Taurus/Auriga. For these directions, most of the reddening is associated with a single cloud complex, for example, the rho Ophiuchus molecular cloud, and as a result, the observations probe moderately dense material. When combined with avaliable data for nearby directions, the survey provides the basis for a comprehensive analysis of the chemistry for these species. The chemical transitions affecting C2 and CN in cloud envelopes were analyzed. The depth into a cloud at which a transition takes place was characterized by tau(sub uv), the grain optical depth at 1000 A. One transition at tau(sub uv) approx. = 2, which arises from, the conversion of C(+) into CO, affects the chemistries for both molecules because of the key role this ion plays. A second one involving production terms in the CN chemistry occurs at tau(sub uv) of approx. = 3; neutral reactions which C2 and CH is more important at larger values for tau(sub uv). The transition from photodissociation to chemical destruction takes place at tau(sub uv) approx. = 4.5 for C2 and CN. The observational data for stars in Sco OB2, Cep OB3, and Taurus/Auriga were studied with chemical rate equations containing the most important production and destruction mechanisms. Because the sample of stars in Sco OB2 includes sight lines with A(sub v) ranging from 1-4 mag, sight lines dominated by photochemistry could be analyzed separately from those controlled by gas-phase destruction. The analysis yielded values for two poorly known rate constants for reactions involved in the production of CN; the reactions are C2 + N yields CN + C and C(+) + NH yields all products. The other directions were analyzed with the inferred values. The predicted column densities for C2 and CN agree with the observed values to better than 50%, and in most instances 20%. When combining the estimates for density and temperature derived from chemical modeling and molecular excitation for a specific cloud, such as the rho Ophiuchus molecular cloud, the portion of the cloud envelope probed by C2 and CN absorption was found to be in pressure equilibrium.

Federman, S. R.↗
NASA NTRS1990

The spiral-compact galaxy pair AM 2208-251: Computer simulations versus observations

The system AM2208-251 is a roughly edge-on spiral extending east-west with a smaller round compact E system about 60 arcsec east of the spiral nucleus along the major axis of the spiral. Bertola, Huchtmeier, and Zeilinger (1990) have presented optical spectroscopic as well as single dish 21 cm observations of this system. Their spectroscopic data show, via emission lines lambda lambda 3727-29A, a rising rotation curve near the nucleus. These spectroscopic observations may indicate a tidal interaction in the system. In order to learn more about such pairs, the authors simulated the interaction using the computer model developed by Miller (1976 a,b, 1978) and modified by the authors (Byrd 1986, 1987, 1988). To do the simulation they need an idea of the mutual orbits of the two galaxies. Their computer model is a two-dimensional polar N-body program. It consists of a self-gravitating disk of particles, within an inert axially symmetric stabilizing halo potential. The particles are distributed in a 24(radial) by 36(azimuthal) polar grid. Self consistent calculations can be done only within the grid area. The disk is modeled with a finite Mestel disk, where all the particles initially move in circular orbits with constant tangential velocities (Mestel 1963), resulting in a flat rotation curve. The gas particles in the spiral's disk, which make up 30 percent of its mass, collide in the following manner. The number of particles in each bin of the polar grid is counted every time step. If it is greater than a given critical density, all the particles in the bin collide, obtaining in the result the same velocities, equal to the average for the bin. This process produces clumps of gas particles-the star formation sites. The authors suppress the collision in the inner part of the disk (within the circle r = 6) to represent the hole seen in the gas in the nuclear bulge of spirals. They thus avoid spurious effects due to collisions in that region. They also varied the size of the collisional bins, which did not affect their conclusions.

Klaric, Mario↗
NASA NTRS1980

Results of Pioneer 10 and 11 meteoroid experiments - Interplanetary and near-Saturn

The meteoroid penetration detectors on Pioneer 10 (channel 0) recorded 95 penetrations through the 25-micron stainless steel test material while the spacecraft was between 1 and 18 AU. The spatial density of 10 to the -9 g meteoroids is found to be essentially constant between 1 and 18 AU. The meteoroid penetration detectors on Pioneer 11 recorded 87 penetrations (55 on channel 0 and 32 on channel 1) through the 50-micron stainless steel test material while the spacecraft was between 1 and 9 AU. It is found that the meteoroids between 4 and 5 AU are not in direct circular or near-circular orbits near the ecliptic plane. The Pioneer 11 data obtained between 4 and 5 AU are best explained by the meteoroids being in randomly inclined orbits of high eccentricity. If meteoroids are in these cometlike orbits, the great increase in penetration flux previously measured near Jupiter with the Pioneer 10 experiment cannot be attributed to gravitational focusing unless the size distribution of meteoroids changes substantially between 1 and 5 AU. At Saturn encounter, the penetration flux increased by about three orders of magnitude, probably as the result of impacts from ring particles. Saturn's ring E is estimated to be 1800 km thick with an optical thickness greater than 10 to the -8.

Humes, D. H.↗
NASA NTRS2005

Airborne Sunphotometer and Solar Spectral Flux Radiometer Measurements During INTEX/ITCT 2004

During the period 12 July - 8 August 2004, the NASA Ames 14-channel Airborne Tracking Sunphotometer (MTS-14) and Solar Spectral Flux Radiometer (SSFR) were operated aboard a Jetstream 31 (J31) aircraft and acquired measurements during nineteen science flights (approx. 53 flight hours) over the Gulf of Maine in support of the INTEX-NA (INtercontinental chemical Transport Experiment-North America) and ITCT (Intercontinental Transport and Chemical Transformation of anthropogenic pollution) field studies. In this paper, we will present results from analyses of those data sets. AATS-14 measures the direct solar beam transmission at fourteen discrete wavelengths (354-2138 nm), and provides instantaneous measurements of aerosol optical depth (AOD) spectra and water vapor column content, in addition to vertical profiles of aerosol extinction and water vapor density during suitable aircraft ascents and descents. SSFR consists of separate nadir and zenith viewing hemispheric FOV sensors that yield measurements of up- and downwelling solar irradiance at a spectral resolution of approx. 8-12 nm over the wavelength range 300-1700 nm. The objectives of the J31-based measurements during INTEX/ITCT were to provide AOD data for the evaluation of MODIS (MODerate-resolution Imaging Spectroradiometer) and MISR (Multi-angle Imaging Spectro-Radiometer) AOD retrievals, quantify sea surface spectral albedo (which can contribute the largest uncertainty to satellite aerosol retrievals for low aerosol loading), test closure (consistency) among suborbital results, test chemical-transport models using AOD profiles, and assess regional radiative forcing by combining satellite and suborbital results. Specific J31 flight patterns were designed to achieve these objectives, and they included a mixture of vertical profiles (spiral and ramped ascents and descents) and constant altitude horizontal transects at a variety of altitudes. Additional information is included in the original extended abstract.

Russell, P. B.↗
NASA NTRS2016

Evaluating Model Parameterizations of Submicron Aerosol Scattering and Absorption with in situ Data from ARCTAS 2008

Accurate modeling of the scattering and absorption of ultraviolet and visible radiation by aerosols is essential for accurate simulations of atmospheric chemistry and climate. Closure studies using in situ measurements of aerosol scattering and absorption can be used to evaluate and improve models of aerosol optical properties without interference from model errors in aerosol emissions, transport, chemistry, or deposition rates. Here we evaluate the ability of four externally mixed, fixed size distribution parameterizations used in global models to simulate submicron aerosol scattering and absorption at three wavelengths using in situ data gathered during the 2008 Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS) campaign. The four models are the NASA Global Modeling Initiative (GMI) Combo model, GEOS-Chem v9- 02, the baseline configuration of a version of GEOS-Chem with online radiative transfer calculations (called GC-RT), and the Optical Properties of Aerosol and Clouds (OPAC v3.1) package. We also use the ARCTAS data to perform the first evaluation of the ability of the Aerosol Simulation Program (ASP v2.1) to simulate submicron aerosol scattering and absorption when in situ data on the aerosol size distribution are used, and examine the impact of different mixing rules for black carbon (BC) on the results. We find that the GMI model tends to overestimate submicron scattering and absorption at shorter wavelengths by 10-23 percent, and that GMI has smaller absolute mean biases for submicron absorption than OPAC v3.1, GEOS-Chem v9-02, or GC-RT. However, the changes to the density and refractive index of BC in GCRT improve the simulation of submicron aerosol absorption at all wavelengths relative to GEOS-Chem v9-02. Adding a variable size distribution, as in ASP v2.1, improves model performance for scattering but not for absorption, likely due to the assumption in ASP v2.1 that BC is present at a constant mass fraction throughout the aerosol size distribution. Using a core-shell mixing rule in ASP overestimates aerosol absorption, especially for the fresh biomass burning aerosol measured in ARCTAS-B, suggesting the need for modeling the time-varying mixing states of aerosols in future versions of ASP.

Alvarado, Matthew J.↗
NASA NTRS1999

A LIS Validation Study at the KSC-ER using LDAR and Field Mill Data

The chance of having the TRMM satellite pass over east central Florida when there is lightning over the NASA Kennedy Space Center (KSC) and USAF Eastern Range (ER) is small; however, such a condition did occur on September 21, 1998 (Day 264). Starting at about 20:40 GMT, the Lightning Imaging Sensor (LIS) reported 5 flashes during a 90 second interval that the KSC-ER was within the sensor field of view. Ground-based instrumentation, the Lightning Detection and Ranging (LDAR) system and a network of electric field mills (FM), detected 6 flashes in the same interval. In this paper, we will compare the times and locations of the optical pulses that were detected by LIS with the times and locations of RF sources (LDAR) and the charges that were deposited by the flash (FM network). We will show that LIS responded to all flashes that the LDAR and FM network detected; however, two discharges that were separated by less than 1 second in time and by about 10 km in space were grouped as one flash by the LIS data processing algorithm. In spite of the fact that all flashes occurred near the edge of the LIS field of view, the locations of the LIS events were consistent with both the LDAR and FM locations (the latter are usually within 1-2 kilometers of each other and often are co-located). Two of the 5 flashes reported by LIS were shifted north by about 8 km from the corresponding LDAR and FM locations. The LIS flash times tended to be after the first LDAR pulse was detected and before the last, and the integrated light signal (per LIS event) was surprisingly constant over the 5 flashes that were detected by LIS. In the future, we plan to study more correlated events and will try to determine whether and how the LIS light signal is related to the charge transfer in the flash and/or the number and spatial extent of RF sources.

Koshak, William J.↗
NASA NTRS1998

Gas Sensors Based on Single-Arm Waveguide Interferometers

Various optical technologies can be implemented in chemical sensing. Sensitive, rugged, and compact systems will be more likely built using interferometric waveguide sensors. Currently existing sensors comprise dual-arm systems with external reference arm, dual-arm devices with internal reference arm such as integrated Mach-Zehnder interferometer, and single-arm systems which employ the interference between different waveguide modes. These latter ones are the most compact and rugged but still sensitive enough to monitor volatile pollutants such as NH3 coming out of industrial refrigerators and fertilizer plants and stocks, NO, NO2, SO2, emitted by industrial burning processes. Single-arm devices in planar waveguide configuration most frequently use two orthogonally polarized modes TE (sub i) and TM (sub i) of the same order i. Sensing effect is based on the difference in propagation conditions for the modes caused by the environment. However, dual-mode single-order interferometers still have relatively low sensitivity with respect to the environment related changes in the waveguide core because of small difference between propagation constants of TE (sub i) and TM (sub i) modes of the same order. Substantial sensitivity improvement without significant complication can be achieved for planar waveguide interferometers using modes of different orders with much greater difference between propagation constants.

Sarkisov, Sergey↗