Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

In-line measurements of below-the-surface food deformation during drying with an interference-based optical fiber strain sensor

Real-time measurements of food deformation are important for quality control in drying, yet they pose significant challenges. In this study, we developed an interference-based optical fiber strain sensor to enable in-line, continuous, below-the-surface strain measurements in drying of soft food samples. Compared to a strain resolution of 8 × 10 -4 at zero strain and 7.2 × 10 -3 at 0.20 strain reported in our previously published work, the present study achieves markedly improved resolutions of 1.3 × 10 -4 at zero strain and 7.8 × 10 -4 at 0.25 strain, which strains are the lower and higher boundaries of the dynamic range, respectively. This nearly order-of-magnitude improvement is attributed to the unique interference-based sensing mechanism, no need for calibration to convert optical signals to strain, and the system-design-enabled immunity to fiber-disk misalignments and light source intensity fluctuations. To demonstrate the in-line process monitoring, deformation measurements of fresh banana slices and sugar cookie doughs were carried out in a benchtop oven and an industrial-scale hot-air pilot dryer, respectively. In both dryers, strain measurements were continuously measured during the whole drying process at various depths and radii below the sample surfaces, with the strains up to 25%. Computer vision was used only in the benchtop drying to confirm the faithfulness of the fiber sensor measurements and cannot provide below-the-surface measurements. The measured spatiotemporal deformation allowed us to confirm the shell-hardening effect and to determine the speed and location of large deformation changes in the whole drying process, the latter of which is related to the sample cracking. To the best of the authors’ knowledge, this study is the first to report on an interferometry-based fiber sensor to measure food deformation. This sensor and the sensing mechanism have high potential for real-time process monitoring and control to prevent over-drying or cracking during drying processes.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Data-Driven Approaches for Bead Geometry Prediction Via Melt Pool Monitoring

In the realm of additive manufacturing, the selection of process parameters to avoid over and under deposition entails a time-consuming and resource-intensive trial-and-error approach. Given the distinct characteristics of each part geometry, there is a pressing need for advancing real-time process monitoring and control to ensure consistent and reliable part dimensional accuracy. Here, this research shows that support vector regression (SVR) and convolutional neural network (CNN) models offer a promising solution for real-time process control due to the models’ abilities to recognize complex, non-linear patterns with high accuracy. A novel experiment was designed to compare the performance of SVR and CNN models to indirectly detect bead height from a coaxial image of a melt pool from a single-layer, single bead build. The study showed that both SVR and CNN models trained on melt pool data collected from a coaxial optical camera can accurately predict the bead height with a mean absolute percentage error of 3.67% and 3.68%, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Kirigami Engineering—Nanoscale Structures Exhibiting a Range of Controllable 3D Configurations

Abstract Kirigami structures provide a promising approach to transform flat films into 3D complex structures that are difficult to achieve by conventional fabrication approaches. By designing the cutting geometry, it is shown that distinct buckling‐induced out‐of‐plane configurations can be obtained, separated by a sharp transition characterized by a critical geometric dimension of the structures. In situ electron microscopy experiments reveal the effect of the ratio between the in‐plane cut size and film thickness on out‐of‐plane configurations. Moreover, geometrically nonlinear finite element analyses (FEA) accurately predict the out‐of‐plane modes measured experimentally, their transition as a function of cut geometry, and provide the stress–strain response of the kirigami structures. The combined computational–experimental approach and results reported here represent a step forward in the characterization of thin films experiencing buckling‐induced out‐of‐plane shape transformations and provide a path to control 3D configurations of micro‐ and nanoscale buckling‐induced kirigami structures. The out‐of‐plane configurations promise great utility in the creation of micro‐ and nanoscale systems that can harness such structural behavior, such as optical scanning micromirrors, novel actuators, and nanorobotics. This work is of particular significance as the kirigami dimensions approach the sub‐micrometer scale which is challenging to achieve with conventional micro‐electromechanical system technologies.

Zhang, Xu↗
DOE OSTI2022

Ligand Coverage and Exciton Delocalization Control Chiral Imprinting in Perovskite Nanoplatelets

Chiral perovskites have generated significant recent interest, yet little is known about how their chiro-optical properties arise. In this study, chiral methylammonium lead halide perovskite nanoplatelets (NPLs) with varied halide and ligand compositions are prepared using direct synthetic methods. Circular dichroism (CD) and 1 H NMR studies find a non-linear relationship between the chiroptical properties and the ratio of chiral phenylethylammonium (PEA) to achiral octylamine (OA) ligands on the NPL surface. We use density functional theory (DFT) computations and a chiral imprinted particle-in-a-box model to rationalize the experimentally observed CD spectra and find that the saturation point of the induced chirality depends on the size of the perovskite exciton relative to the size of the ligands. Temperature-dependent CD and 1 H NMR studies, combined with DFT analysis, show that both the CD intensity and sign depend strongly on the structure and orientation of the ligands. Furthermore, this work reveals the complex nature of chiral imprinting in perovskite nanostructures and establishes a simple physical model for ligand-induced chiral imprinting to guide the further development of chiral materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Searching for high-frequency gravitational waves with phonons

The gravitational wave (GW) spectrum at frequencies above a kHz is a largely unexplored frontier. We show that detectors with sensitivity to single-phonon excitations in crystal targets can search for GWs with frequencies, 1 THz ≲ f ≲ 100 THz , corresponding to the range of optical phonon energies, 1 meV ≲ ω ≲ 100 meV . Such detectors are already being built to search for light dark matter (DM), and therefore sensitivity to high-frequency GWs will be achieved as a byproduct. We begin by deriving the absorption rate of a general GW signal into single phonons. We then focus on carefully defining the detector sensitivity to monochromatic and chirp signals, and compute the detector sensitivity for many proposed light DM detection targets. The detector sensitivity is then compared to the signal strength of candidate high-frequency GW sources, e.g., superradiant annihilation and black hole inspiral, as well as other recent detector proposals in the 1 MHz ≲ f ≲ 100 THz frequency range. With a judicious choice of target materials, a collection of detectors could optimistically achieve sensitivities to monochromatic signals with h 0 ∼ 10 − 23 − 10 − 25 over 1 THz ≲ f ≲ 100 THz . Published by the American Physical Society 2024

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

High-Fidelity Energy Deposition Ignition Model Coupled with Flame Propagation Models at Engine-like Flow Conditions

With the heightened pressure on car manufacturers to increase the efficiency and reduce the carbon emissions of their fleets, more challenging engine operation has become a viable option. Highly dilute, boosted, and stratified charge, among others, promise engine efficiency gains and emissions reductions. At such demanding engine conditions, the spark-ignition process is a key factor for the flame initiation propagation and the combustion event. From a computational standpoint, there exist multiple spark-ignition models that perform well under conventional conditions but are not truly predictive under strenuous engine operation modes, where the underlying physics needs to be expanded. In this paper, a hybrid Lagrangian-Eulerian spark-ignition (LESI) model is coupled with different turbulence models, grid sizes, and combustion models. The ignition model, previously developed, relies on coupling Eulerian energy deposition with a Lagrangian particle evolution of the spark channel, at every time-step. The spark channel is attached to the electrodes and allowed to elongate at a speed derived from the flow velocity. The LESI model is used to simulate spark ignition in a nonquiescent crossflow environment at engine-like conditions, using converge commercial computational fluid dynamics (CFD) solver. The results highlight the consistency, robustness, and versatility of the model in a range of engine-like setups, from typical with Reynolds-averaged Navier-Stokes (RANS) and a larger grid size to high fidelity with large-eddy simulation (LES) and a finer grid size. The flame kernel growth is then evaluated against Schlieren images from an optical constant volume ignition chamber with a focus on the performance of flame propagation models, such as G-equation and thickened flame model, versus the baseline well-stirred reactor model. Finally, future development details are discussed.

Advanced ignition modeling↗
DOE OSTI2023

The application of parallel kinetic simulations to laser and electron transport through plasmas (Final technical report)

This is a final report for the grant entitled, “The application of parallel kinetic simulations to laser and electron transport through plasmas”. The objectives of this grant were to significantly advance the fundamental understanding of the nonlinear optics of plasmas and electron transport in high-energy-density laboratory plasmas (HEDLP), including conditions of relevance to Inertial Fusion Energy (IFE). The ultimate goal was to use the understanding to determine how to fully control laser plasma interactions. The primary research tools were our own kinetic particle-in-cell software, OSIRIS, that includes kinetic physics and can run effectively on leadership class computing facilities. Therefore, one objective was to ensure that OSIRIS in continually improved so that it was more accurate and could effectively utilize state-of-the-art computing facilities. Another objective was to attract and train young researchers into the field of high energy density plasma physics. To meet the research objectives, the funds from this proposal were used to conduct research on stimulated Raman scattering (SRS) and enhance our PIC software OSIRIS. It was found that small normalized magnetic fields can in some cases mitigate SRS and that speckles can mutually interact through SRS. It was also found that it is possible for instabilities drive near quarter critical (e.g., the high frequency hybrid instability-HFHI) can generate light waves that propagate back down a density gradient where they can rescatter into the HFHI at 1/16 of the original quarter critical density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

A hybrid Monte Carlo-deterministic second moment method with efficient variance reduction

In this work, we present a hybrid method that combines Monte Carlo with deterministic finite element methods to solve a linear Boltzmann transport equation. Our hybrid method runs orders of magnitude faster than Monte Carlo, without sacrificing accuracy, for a proxy problem from radiative transfer that contains both optically-thick and optically-thin material. We believe that this is the first demonstration of a hybrid Second Moment Method in more than one spatial dimension, the first to consider more than one material, and the first to use variance reduction. Our variance reduction approach arises from an asymptotic analysis in which we show that the magnitude of the scattering source grows without bound. We transform the problem to compute the deviation of the radiation intensity from isotropy. The magnitude of the source in the transformed problem is bounded, and the quality of the hybrid method solution is dramatically improved by a substantial reduction in the variance.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Cr plasma-material-interaction in PISCES-RF: D thermal release, retention, and erosion

Pure chromium (Cr) targets were exposed to high-flux deuterium (D) plasmas in the Pisces-RF linear plasma device, and measurements of D retention, release, and erosion were subsequently performed. Post-exposure D retention was quantified using temperature-programmed desorption on Cr targets irradiated by 50 eV ions over a broad range of exposure temperatures (423–873 K) and ion fluences (3 × 10 24 – 3 × 10 26 m −2 ). The retained D inventory was observed to decrease rapidly with increased exposure temperature, from approximately ∼7 × 10 20 m −2 at ∼ 420 K, to then saturate near ∼ 10 20 m −2 for exposure temperatures above ∼550 K. Separately, at fixed exposure temperature (∼450 K), D retention was found to have only a weak dependence on increasing ion fluence. Lastly, the erosion of Cr in D plasma was investigated for ion impact energies in the range 40 ≤ E i ≤ 250 eV. Erosion was inferred using optical emission spectroscopy (OES) from the ratio of emission lines (Cr I (425.4 nm)/D I (656.1 nm)) measured close to the target. Conversion of the OES yield data to net erosion yield was made with singular ion energy target mass-loss measurements. These net erosion yield data were then further corrected to obtain gross erosion yield by accounting for a re-deposition factor, computed using a simple model. The gross erosion yield is found to be 2–4 times lower than predicted by SDTrimSP, consistent with that typically observed for light-ion sputtering under high-flux plasma conditions.

Chromium↗
DOE OSTI2025

Broadband coherent XUV light from e − / e + microbunching in an intense laser pulse

Attosecond pulses of coherent extreme ultraviolet (XUV) light are instrumental for investigating subatomic dynamics and can be produced using a free-electron laser (FEL). It has been suggested that an optical FEL, which employs a laser pulse in place of a conventional undulator, could enable a dramatically more compact implementation of such a light source. Yet, the high electron density and subsequent high emittance implied by an optical FEL makes this concept challenging to realize with an electron beam. There has been impressive progress in recent years producing collimated dense and relativistic beams of electrons and positrons in the laboratory. As we demonstrate here, the inherent stability of a quasi-neutral electron-positron beam mitigates Coulomb expansion, and renders it a promising alternative source of coherent light. Specifically, we show via computer simulations that broadband coherent light in the XUV domain, which takes the form of 8-as pulses at 92-as intervals, can be generated by microbunching of relativistic electrons and positrons in a laser pulse. This process occurs over a sub-millimeter length scale, enabling the development of light sources which are orders-of-magnitude more compact than existing sources, with potential applications in physics, chemistry, biology, and industry.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Exact two-body expansion of the many-particle wave function

Progress toward the solution of the strongly correlated electron problem has been stymied by the exponential complexity of the wave function. Previous work established an exact two-body exponential product expansion for the ground-state wave function. By developing a reduced density-matrix analog of Dalgarno-Lewis perturbation theory, we prove here that (i) the two-body exponential product expansion is rapidly and globally convergent with each operator representing an order of a renormalized perturbation theory, (ii) the energy of the expansion converges quadratically near the solution, and (iii) the expansion is exact for both ground and excited states. The two-body expansion offers a reduced parametrization of the many-particle wave function as well as the two-particle reduced density matrix with potential applications on both conventional and quantum computers for the study of strongly correlated quantum systems. In this work, we demonstrate the result with the exact solution of the contracted Schrödinger equation for the molecular chains H 4 and H 5 .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Modeling Nanosecond-Pulsed Spark Discharge and Flame Kernel Evolution

Dilute combustion, either using exhaust gas recirculation or with excess air, is considered a promising strategy to improve the thermal efficiency of internal combustion engines. However, the dilute air-fuel mixture, especially under intensified turbulence and high-pressure conditions, poses significant challenges for ignitability and combustion stability, which may limit the attainable efficiency benefits. In-depth knowledge of the flame kernel evolution to stabilize ignition and combustion in a challenging environment is crucial for effective engine development and optimization. To date, a comprehensive understanding of ignition processes that result in the development of fully predictive ignition models usable by the automotive industry does not yet exist. Spark-ignition consists of a wide range of physics that includes electrical discharge, plasma evolution, joule-heating of gas, and flame kernel initiation and growth into a self-sustainable flame. In this study, an advanced approach is proposed to model spark-ignition energy deposition and flame kernel growth. To decouple the flame kernel growth from the electrical discharge, a nanosecond-pulsed high-voltage discharge is used to trigger spark-ignition in an optically accessible small ignition test vessel with a quiescent mixture of air and methane. Initial conditions for the flame kernel, including its thermodynamic state and species composition, are derived from a plasma-chemical equilibrium calculation. The geometric shape and dimension of the kernel are characterized using a multi-dimensional thermal plasma solver. Here, the proposed modeling approach is evaluated using a high-fidelity computational fluid dynamics procedure to compare the simulated flame kernel evolution against flame boundaries from companion Schlieren images.

42 ENGINEERING↗
DOE OSTI2022

Carbon Nanotube Devices for Quantum Technology

Carbon nanotubes, quintessentially one-dimensional quantum objects, possess a variety of electrical, optical, and mechanical properties that are suited for developing devices that operate on quantum mechanical principles. The states of one-dimensional electrons, excitons, and phonons in carbon nanotubes with exceptionally large quantization energies are promising for high-operating-temperature quantum devices. Here, we discuss recent progress in the development of carbon-nanotube-based devices for quantum technology, i.e., quantum mechanical strategies for revolutionizing computation, sensing, and communication. We cover fundamental properties of carbon nanotubes, their growth and purification methods, and methodologies for assembling them into architectures of ordered nanotubes that manifest macroscopic quantum properties. Most importantly, recent developments and proposals for quantum information processing devices based on individual and assembled nanotubes are reviewed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

MIRC-X: A Highly Sensitive Six-telescope Interferometric Imager at the CHARA Array

Michigan InfraRed Combiner-eXeter (MIRC-X) is a new highly sensitive six-telescope interferometric imager installed at the CHARA Array that provides an angular resolution equivalent of up to a 330 m diameter baseline telescope in J- and H-band wavelengths ((λ/(2B))∼0.6 mas). We upgraded the original Michigan InfraRed Combiner (MIRC) instrument to improve sensitivity and wavelength coverage in two phases. First, a revolutionary sub-electron noise and fast-frame-rate C-RED ONE camera based on an SAPHIRA detector was installed. Second, a new-generation beam combiner was designed and commissioned to (i) maximize sensitivity, (ii) extend the wavelength coverage to J band, and (iii) enable polarization observations. A low-latency and fast-frame-rate control software enables high-efficiency observations and fringe tracking for the forthcoming instruments of the CHARA Array. Since mid-2017, MIRC-X has been offered to the community and has demonstrated best-case H-band sensitivity down to 8.2 correlated magnitude. MIRC-X uses single-mode fibers to coherently combine the light from six telescopes simultaneously with an image-plane combination scheme and delivers a visibility precision better than 1%, and closure phase precision better than 1°. MIRC-X aims at (i) imaging protoplanetary disks, (ii) detecting exoplanets with precise astrometry, and (iii) imaging stellar surfaces and starspots at an unprecedented angular resolution in the near-infrared. In this paper, we present the instrument design, installation, operation, and on-sky results, and demonstrate the imaging capability of MIRC-X on the binary system ι Peg. The purpose of this paper is to provide a solid reference for studies based on MIRC-X data and to inspire future instruments in optical interferometry.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Super-localisation of a point-like emitter in a resonant environment: Correction of the mirage effect

In this paper, we show that it is possible to overcome one of the fundamental limitations of super-resolution microscopy: the necessity to be in an optically homogeneous environment. Using recent modal approximation results from [ 10 , 7 ], we show, as a proof of concept, that it is possible to recover the position of a single point-like emitter in a known resonant environment from far-field measurements, with a precision two orders of magnitude below the classical Rayleigh limit. The procedure does not involve solving any partial differential equation, is computationally light (optimisation in \begin{document}$ \mathbb{R}^d $\end{document} with \begin{document}$ d $\end{document} of the order of \begin{document}$ 10 $\end{document} ) and is therefore suited for the recovery of a very large number of single emitters.

Mathematics↗
DOE OSTI2026

How Does Metal Spin State Affect Electronic Communication in Mixed-Valence Dimers? Insights from Ultrafast Near-Infrared and Soft X-ray Transient Absorption Spectroscopy

Recent advancements in photocatalysis, photovoltaics, and quantum information science take advantage of electron spin, and determining how spin multiplicity affects electron transfer is key to understanding these phenomena. Here, in this study, we examine how metal spin state affects electronic communication in an organometallic mixed-valence dimer, ferrocenyl cobaltocenium ([Fe II Cp 2 Co III Cp 2 ] + ). This complex can be photoexcited from its low-spin singlet Fe II ground state to form intermediate-spin triplet Fe II and high-spin quintet Fe II excited states. Using femtosecond optical transient absorption (OTA) spectroscopy with visible (vis), near-infrared (NIR), and short-wave IR (SWIR) probes, supported by time-dependent density functional theory (TD-DFT) calculations, we measure Fe II Co III →Fe III Co II intervalence charge transfer (IVCT) bands in each of the Fe II spin states. Mulliken–Hush analysis of the excited-state IVCT bands was used to compute the electronic coupling between the metal centers in all three spin states, which increased as quintet < triplet < singlet. Meanwhile, the peak energy of the bands, and thus the ΔG of the IVCT transition, increased as triplet < quintet < singlet. Then, to directly probe the electronic structure at each metal center, we employed picosecond soft X-ray transient absorption (XTA) spectroscopy at the Fe and Co L 3 edges. Our results show that the low-spin and high-spin states of [Fe II Cp 2 Co III Cp 2 ] + are valence-localized, while the intermediate-spin state is partially delocalized. The differences in charge delocalization are attributed to differences in orbital occupation and geometry that affect the free energy and superexchange coupling.

Burke, John H. [Univ. of Illinois at Urbana-Champa↗
DOE OSTI2024

Ligand-Induced Size-Dependent Circular Dichroism in Quantum Dots

Recent experiments have probed the chiral properties of semiconductor nanocrystal (NC) quantum dots (QDs), but understanding the circular dichroism line shape, excitonic features, and chirality induction mechanism remains a challenge. We propose an atomistic pseudopotential method to model chiral ligand passivated QDs, computing circular dichroism (CD) spectra for CdSe QDs (2.6-3.8 nm). We find strong agreement between calculated and measured line shapes, predicting consistent bisignate line shapes with decreasing CD magnitude as size increases. Further, our analysis reveals the origin of bisignate line shapes, arising from nondegenerate excitons with opposing angular momenta. We also explore the impact of chiral ligand orientation on QD surfaces, observing changes in the optical activity magnitude and sign. This orientation sensitivity offers the means to distinguish ordered from disordered ligand configurations, facilitating the study of order-disorder transitions at ligand-QD interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗