Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNESIUM COMPOUND”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Polarity inversion of N-face GaN by plasma-assisted molecular beam epitaxy

The polarity of GaN grown by plasma-assisted molecular beam epitaxy was inverted from N-face to Ga-face by simultaneously exposing the surface to Mg and activated N fluxes during a growth interruption at a reduced substrate temperature. Growth studies suggested that a Mg{sub x}N{sub y} compound was responsible for inverting the crystal. The change in polarity was verified in situ by reflection high energy electron diffraction via GaN surface reconstructions, and ex situ by convergent beam electron diffraction and KOH etch studies. The surface of the inverted material showed smooth step flow features. Ga-face high electron mobility transistors with good dc and small signal performance were fabricated on the inverted epilayers. A drain-source current of 0.84 A/mm was measured at a gate-source voltage of +1 V. Current-gain cutoff and maximum oscillation frequencies of 22 and 53 GHz, respectively, were measured in these devices. The device performance is similar to that of Ga-face transistors with comparable dimensions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electronic and crystalline structures of zero band-gap LuPdBi thin films grown epitaxially on MgO(100)

Thin films of the proposed topological insulator LuPdBi-a Heusler compound with the C1{sub b} structure-were prepared on Ta-Mo-buffered MgO(100) substrates by co-sputtering from PdBi{sub 2} and Lu targets. Epitaxial growth of LuPdBi films was confirmed by X-ray diffraction and reflection high-energy electron diffraction. The root-mean-square roughness of the films was as low as 1.45 nm, even though the films were deposited at high temperature. The film composition is close to the ideal stoichiometric ratio. The valence band spectra of the LuPdBi films, observed by hard X-ray photoelectron spectroscopy, correspond very well with the ab initio-calculated density of states.

36 MATERIALS SCIENCE↗

Sputter-Deposited Oxides for Interface Passivation of CdTe Photovoltaics

Commercial CdTe PV modules have polycrystalline thin films deposited on glass, and devices made in this format have exceeded 22% efficiency. Devices made by the authors with a magnesium zinc oxide window layer and tellurium back contact have achieved efficiency over 18%, but these cells still suffer from an open-circuit voltage far below ideal values. Oxide passivation layers made by sputter deposition have the potential to increase voltage by reducing interface recombination. CdTe devices with these passivation layers were studied with photoluminescence (PL) emission spectroscopy and time-resolved photoluminescence (TRPL) to detect an increase in minority carrier lifetime. Because these oxide materials exhibit barriers to carrier collection, micropatterning was used to expose small point contacts while still allowing interface passivation. TRPL decay lifetimes have been greatly enhanced for thin polycrystalline absorber films with interface passivation. Device performance was measured and current collection was mapped spatially by light-beam-induced current.

14 SOLAR ENERGY↗

In situ evidence for an ancient aqueous environment at Meridiani Planum, Mars

Sedimentary rocks at Eagle crater in Meridiani Planum are composed of fine-grained siliciclastic materials derived from weathering of basaltic rocks, sulfate minerals (including magnesium sulfate and jarosite) that constitute several tens of percent of the rock by weight, and hematite. Cross-stratification observed in rock outcrops indicates eolian and aqueous transport. Diagenetic features include hematite-rich concretions and crystal-mold vugs. We interpret the rocks to be a mixture of chemical and siliciclastic sediments with a complex diagenetic history. The environmental conditions that they record include episodic inundation by shallow surface water, evaporation, and desiccation. The geologic record at Meridiani Planum suggests that conditions were suitable for biological activity for a period of time in martian history.

Water↗

Molecular-beam epitaxy of heterostructures of wide-gap II–VI compounds for low-threshold lasers with optical and electron pumping

The paper presents basic approaches in designing and growing by molecular beam epitaxy of (Zn,Mg)(S,Se)-based laser heterostructures with multiple CdSe quantum dot (QD) sheets or ZnCdSe quantum wells (QW). The method of calculation of compensating short-period ZnSSe/ZnSe superlattices (SLs) in both active and waveguide regions of laser heterostructures possessing the different waveguide thickness and different number of active regions is presented. The method allowing reduction of the density of nonequilibrium point defects in the active region of the II–VI laser structures has been proposed. It utilizes the migration enhanced epitaxy mode in growing the ZnSe QW confining the CdSe QD sheet. The threshold power density as low as P{sub thr} ∼ 0.8 kW/cm{sup 2} at T = 300 K has been demonstrated for laser heterostructure with single CdSe QD sheet and asymmetric graded-index waveguide with strain-compensating SLs.

36 MATERIALS SCIENCE↗

Concentration of simple aldehydes by sulfite-containing double-layer hydroxide minerals: implications for biopoesis

Environmental conditions play an important role in conceptual studies of prebiotically relevant chemical reactions that could have led to functional biomolecules. The necessary source compounds are likely to have been present in dilute solution, raising the question of how to achieve selective concentration and to reach activation. With the assumption of an initial 'RNA World', the questions of production, concentration, and interaction of aldehydes and aldehyde phosphates, potential precursors of sugar phosphates, come into the foreground. As a possible concentration process for simple, uncharged aldehydes, we investigated their adduct formation with sulfite ion bound in the interlayer of positively charged expanding-sheet-structure double-layer hydroxide minerals. Minerals of this type, initially with chloride as interlayer counter anion, have previously been shown to induce concentration and subsequent aldolization of aldehyde phosphates to form tetrose, pentose, and hexose phosphates. The reversible uptake of the simple aldehydes formaldehyde, glycolaldehyde, and glyceraldehyde by adduct formation with the immobilized sulfite ions is characterized by equilibrium constants of K=1.5, 9, and 11, respectively. This translates into an observable uptake at concentrations exceeding 50 mM.

NASA Discipline Exobiology↗

Magneto-optical spectroscopy of Co{sub 2}FeSi Heusler compound

Magneto-optical and electronic properties of the Co{sub 2}FeSi Heusler compound were studied by polar Kerr magneto-optical spectroscopy and ab-initio calculations. The thin-film samples were grown by dc/rf magnetron co-sputtering on MgO(100) substrates. A Cr seed layer was deposited prior to the Co{sub 2}FeSi layer to achieve its epitaxial growth. The magneto-optical spectroscopy was carried out using generalized magneto-optical ellipsometry with rotating analyzer in the photon energy range from 1.4 to 5.5 eV with an applied magnetic field of up to 1.2 T. The polar Kerr spectra showed a smooth spectral behavior up to 5.5 eV indicating nearly free charge carriers. Experimental data were compared with ab-initio calculations based on density functional theory employing the full-potential linearized augmented plane wave method.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low temperature phase transition and crystal structure of CsMgPO{sub 4}

CsMgPO{sub 4} doped with radioisotopes is a promising compound for usage as a radioactive medical source. However, a low temperature phase transition at temperatures close to ambient conditions (∼−40 °C) was observed. Information about such kind of structural changes is important in order to understand whether it can cause any problem for medical use of this compound. The phase transition has been investigated in detail using synchrotron powder diffraction, Raman spectroscopy and DFT calculations. The structure undergoes a transformation from an orthorhombic modification, space group Pnma (RT phase) to a monoclinic polymorph, space group P2{sub 1}/n (LT phase). New LT modification adopts similar to RT but slightly distorted unit cell: a=9.58199(2) Å, b=8.95501(1) Å, c=5.50344(2) Å, β=90.68583(1)°, V=472.198(3) Å{sup 3}. CsMgPO{sub 4} belongs to the group of framework compounds and is made up of strictly alternating MgO{sub 4}- and PO{sub 4}-tetrahedra sharing vertices. The cesium counter cations are located in the resulting channel-like cavities. Upon the transformation a combined tilting of the tetrahedra is observed. A comparison with other phase transitions in ABW-type framework compounds is given. - Graphical abstract: Structural behavior of β-tridymite-type phosphate CsMgPO{sub 4}, considered as potential chemical form for radioactive Cs-source has been studied at near ambient temperatures. A phase transition at (∼−40 °C) has been found and investigated. It has been established that the known orthorhombic RT modification, space group Pnma, adopts a monoclinic cell with space group P2{sub 1}/n at low temperatures. In this paper, we present results of structural analysis of changes accompanying this phase transition and discuss its possible impact on the application properties. - Highlights: • β-Tridymite type phosphate CsMgPO{sub 4} undergoes so called translationengleiche phase transition of index 2 at −40 °C. • The structure transforms from an orthorhombic (space group Pnma) to a monoclinic (space group P2{sub 1}/n) phase. • In comparison with the RT form, the LT modification adopts a similar but slightly distorted unit cell.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

AB Initio Characterization of MgCCH, MgCCH(+), and MgC2, and Pathways to their Formation in the Interstellar Medium

A study of Mg-bearing compounds has been performed in order to determine molecular properties which are critical for planning new astronomical searches and laboratory studies. The primary focus of the work is on MgCCH, MgCCH(+), and the isomers of MgC2. Only MgCCH has been identified in laboratory studies. Additional calculations have been carried out on MgH, MgNC, MgCN, and their cations in an effort to evaluate pathways to the formation of MgCCH and MgCCH(+) in the InterStellar Medium (ISM) or in circumstellar envelopes. Correlated ab initio methods and correlation-consistent basis sets have been employed. Properties including structures, rotational constants, dipole moments, and harmonic frequencies are reported. A transition state between linear MgCC and cyclic MgC2 has been characterized and was found to yield a minimal barrier (approx. 0.5 kcal/mole), indicating easy interconversion to the cyclic form. Direct reactions in the ISM between Mg or Mg(+) and HCCH are precluded by energetic considerations, but a number of ion- molecule or neutral-neutral exchange reactions between CCH and various Mg-containing species offer plausible pathways to MgCCH or MgCCH(+). Weakly bound MgH may react with CCH to form MgCCH, but MgH has not been detected. Both MgNC and MgCN have been observed, but reactions with CCH are slightly endothermic by 1-3 kcal/mole. Although MgH(+), MgNC(+), and MgCN(+) have not been detected, their reactions with CCH to form MgCCH(+) are all exothermic. With only a small barrier separating linear MgCC and cyclic MgC2, the dissociative recombination of MgCCH(+) with an electron is expected to yield cyclic MgC2, and regenerate Mg and CCH. New astronomical searches for MgCCH, MgCCH(+), cyclic MgC2, MgNC(+), and MgCN(+) will provide further insight into organo-magnesium astrochemistry.

Woon, David E.↗

Nanostructured multilayered thin film barriers for Mg{sub 2}Si thermoelectric materials

The Mg{sub 2}Si-based alloys are promising candidates for thermoelectric energy conversion in the middle-high temperature range in order to replace lead compounds. The main advantages of silicide-based thermoelectrics are the nontoxicity and the abundance of their constituent elements in the earth crust. The drawback of such kind of materials is their oxygen sensitivity at high temperature that entails their use under vacuum or inert atmosphere. In order to limit the corrosion phenomena, nanostructured multilayered molybdenum silicide-based materials were deposited via RF magnetron sputtering onto stainless steel, alumina and silicon (100) to set up the deposition process and then onto Mg{sub 2}Si pellets. XRD, EDS, FE-SEM and electrical measurements at high temperature were carried out in order to obtain, respectively, the structural, compositional, morphological and electrical characterization of the deposited coatings. At the end, the mechanical behavior of the system thin film/Mg{sub 2}Si-substrate as a function of temperature and the barrier properties for oxygen protection after thermal treatment in air at high temperature were qualitatively evaluated by FE-SEM.

36 MATERIALS SCIENCE↗

Express and low-cost microwave synthesis of the ternary Chevrel phase Cu{sub 2}Mo{sub 6}S{sub 8} for application in rechargeable magnesium batteries

The ternary Chevrel phase Cu{sub 2}Mo{sub 6}S{sub 8} was successfully synthetized using a simple and cost-effective solid-state microwave-assisted reaction. While solid-state routes require days of high-temperature treatment under inert atmosphere, highly pure and crystalline Cu{sub 2}Mo{sub 6}S{sub 8} could be obtained in only 400 s from this precursor, the Chevrel binary phase Mo{sub 6}S{sub 8} was then obtained by copper removal through acidic leaching, and was evaluated as a positive electrode material for Mg-battery. The electrochemical performance in half-cell configuration shows reversible capacity exceeding 80 mAh/g, which is comparable to previous works carried out with materials synthesized by conventional high-temperature solid-state routes. - Graphical abstract: Ultrafast micro-wave synthesis of Chevrel phase Cu{sub 2}Mo{sub 6}S{sub 8} towards Mo{sub 6}S{sub 8} as positive electrode of Mg-battery. - Highlights: • Chevrel phase Cu{sub 2}Mo{sub 6}S{sub 8} is synthesized by fast microwave-assisted solid-state reaction. • Highly-pure and well-crystalline Cu{sub 2}Mo{sub 6}S{sub 8} is obtained. • Mo{sub 6}S{sub 8} obtained from leaching is tested as a positive electrode for Mg batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Co{sub 2}FeAl based magnetic tunnel junctions with BaO and MgO/BaO barriers

We succeed to integrate BaO as a tunneling barrier into Co{sub 2}FeAl based magnetic tunnel junctions (MTJs). By means of Auger electron spectroscopy it could be proven that the applied annealing temperatures during BaO deposition and afterwards do not cause any diffusion of Ba neither into the lower Heusler compound lead nor into the upper Fe counter electrode. Nevertheless, a negative tunnel magnetoresistance (TMR) ratio of -10% is found for Co{sub 2}FeAl (24 nm) / BaO (5 nm) / Fe (7 nm) MTJs, which can be attributed to the preparation procedure and can be explained by the formation of Co- and Fe-oxides at the interfaces between the Heusler and the crystalline BaO barrier by comparing with theory. Although an amorphous structure of the BaO barrier seems to be confirmed by high-resolution transmission electron microscopy (TEM), it cannot entirely be ruled out that this is an artifact of TEM sample preparation due to the sensitivity of BaO to moisture. By replacing the BaO tunneling barrier with an MgO/BaO double layer barrier, the electric stability could effectively be increased by a factor of five. The resulting TMR effect is found to be about +20% at room temperature, although a fully antiparallel state has not been realized.

36 MATERIALS SCIENCE↗

Ultrafast intramolecular relaxation dynamics of Mg- and Zn-bacteriochlorophyll a

Ultrafast excited-state dynamics of the photosynthetic pigment (Mg-)bacteriochlorophyll a and its Zn-substituted form were investigated by steady-state absorption/fluorescence and femtosecond pump-probe spectroscopic measurements. The obtained steady-state absorption and fluorescence spectra of bacteriochlorophyll a in solution showed that the central metal compound significantly affects the energy of the Q{sub x} state, but has almost no effect on the Q{sub y} state. Photo-induced absorption spectra were recorded upon excitation of Mg- and Zn-bacteriochlorophyll a into either their Q{sub x} or Q{sub y} state. By comparing the kinetic traces of transient absorption, ground-state beaching, and stimulated emission after excitation to the Q{sub x} or Q{sub y} state, we showed that the Q{sub x} state was substantially incorporated in the ultrafast excited-state dynamics of bacteriochlorophyll a. Based on these observations, the lifetime of the Q{sub x} state was determined to be 50 and 70 fs for Mg- and Zn-bacteriochlorophyll a, respectively, indicating that the lifetime was influenced by the central metal atom due to the change of the energy gap between the Q{sub x} and Q{sub y} states.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Study Of Geological Disposal Facility (GDF) Ageing Phenomena In Bentonite - 17605

Since the 1950's, the UK's nuclear activity in energy, defence and medicine has led to the accumulation of a large amount of higher activity radioactive waste (HAW). Most of nuclear waste arises in a wide variety of physical and chemical forms with different radioisotopes and loadings. Due to complexity in HAW, it is imperative that there be a rigorous management system that ensures population and environmental safety over extended periods. The concept of Deep Geological Disposal of waste in a stable geological formation is, nowadays, an internationally accepted solution as the surest and the most viable long term method for management. Any future Geological Disposal Facility (GDF) will comprise, among other artificial and natural engineered barriers, a barrier immediately around the waste containers compounded by a sealing material. The long-term stability of a GDF will be determined by the design and construction of the engineered barriers, and the mechanical, hydraulic and geochemical interactions that may happen between the different engineered components as a result of combined processes such as the heat produced by radioactive decay and the ion water composition of the surrounding host rock. Bentonite clay has been selected as the most promising buffer and backfill material in many disposal programmes because of its swelling capacity, low permeability, plasticity and cation exchange capacity. In the nuclear scope, bentonite testing at different scale-lengths (laboratory and field scale) has been performed and implemented in order to examine the thermo-hydro-mechanical (THM) and thermo-hydro-geochemical (THG) processes that may happen in the engineered barriers and geological settings associated with a GDF. Two major European field scale tests have been performed to better understand bentonite performance and behaviour immediately after HAW emplacements. The Full-Scale Engineered Barriers Experiment (FEBEX) at the Grimsel Test Sit (Switzerland) and the Alternative Buffer Material (ABM) Project at the Aespoe Hard Rock Laboratory (Sweden). The Febex Experiment was a pilot project designed for 'field research' of HAW repository hosted in crystalline rock where surrogate HAW canisters were placed horizontally in drifts, surrounded by compacted blocks of bentonite, sealed by a concrete plug and maintaining a constant canister surface temperature of 100 deg. C. After five years of operation, a partial dismantling was carried out in 2002. Heater processes occurring in the surrounding bentonite. The dismantling of the heater no. 2 (after 18 years of operation) started in late 2014 and is planned to be finished at the end of 2016 (termed FEBEX-DP). The FEBEX Project utilised bentonite from the Cortijo de Archidona deposit (Almeria, Spain). This 'Febex' bentonite is sourced from calcium-magnesium montmorillonite with good properties in relation to swelling capacity, permeability, adsorption capacity, and thermal conductivity. The ABM Project is a large-scale programme that has been running since 2006. The programme is designed to study a suite of possible buffer materials and correlate the physical and chemical properties of eleven different types of bentonites to their fundamental mineralogical properties. The ABM test consists in three 'packages' containing a central heater tube surrounded by different pre-compacted bentonite blocks and instrumentation. Each 'package' was installed in separate boreholes. The target temperature for the surface of the heated tubes in contact with the bentonite was 130 deg. C. Both FEBEX and ABM test the bentonite was saturated with water percolating from surrounding host rock (FEBEX and ABM) and also via artificial supply systems (ABM), being the water itself acting as a long term corrosion agent. For both experiments and emerging interest is in the interaction of bentonite with metallic components, under geological disposal conditions are not considered to be thermodynamically stable and hence arising corrosion products could interact with the buffer. These interactions depend on various factors such as the redox potential, temperature, pH, solute concentration and buffer material characteristics. During the operational phases of the FEBEX and ABM and after its 'closure' a significant volume of air was found to be retained in the bentonite. Under these conditions a period of initial aerobic corrosion by the air in the bentonite barrier would have occurred followed by establishment of anaerobic corrosion would be the dominant process ongoing. The anaerobic corrosion began when the bentonite became water saturated. Under these conditions, the water acted as the major oxidant. The present project focuses on the characterization of samples arising from the FEBEX and ABM Projects as well as performing additional independent experiments designed to complement these prior studies. Characterization will focus mainly on corrosion related alteration combined with thermal effects. Through detailed sample characterization, the intention is to achieve a greater knowledge regarding the changes to the bentonite under the experimental conditions to which it was exposed, and plausible alterations in its THM and THG properties occurring during the experiment due to blended effects of temperature,water content, engineering structural components and solutes are also to be measured. The fulfilment of a large-scale 'in-situ' test is intricate, time-consuming and with an abundance of external variables that are not always well controlled. For this reason, the University of Bristol is performing a series of well constrained time-resolved laboratory tests which bentonite is being subjected to different possible scenarios that may happen whilst in a HAW repository. In virtue of this experiment, the UoB aims to understand the illitisation and cementation process and their effects on bentonite safety properties. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A study of H+ production using metal hydride and other compounds by means of laser ion source

A laser ion source can provide wide variety of ion beams from solid target materials, however, it has been difficult to create proton beam efficiently. We examined capability of proton production using beeswax, polyethylene, and metal hydrides (MgH2 and ZrH2) as target materials. The results showed that beeswax and polyethylene could not be used to produce protons because these targets are transparent to the laser wavelength of 1064 nm. On the other hand, the metal hydrides could supply protons. Although the obtained particle numbers of protons were less than those of the metal ions, the metal hydrides could be used as a target for proton laser ion source.

08 HYDROGEN↗

High-spin states in {sup 96,97}Nb

The high-spin level structures of the {sup 96,97}Nb isotopes have been studied. The isotopes were produced in the fission of the compound systems formed in two heavy-ion-induced reactions, {sup 24}Mg (134.5 MeV) + {sup 173}Yb and {sup 23}Na (129 MeV) + {sup 176}Yb. Gamma-ray spectroscopy was accomplished with the Gammasphere array. High-spin states are observed for the first time in both isotopes with excitation energies up to 5.2 and 6.6 MeV in {sup 96,97}Nb, respectively. The coupling of the odd proton occupying the g{sub 9/2} orbital to the yrast states in the subshell closure nucleus of {sup 96}Zr can account for the first excited states of {sup 97}Nb. A comparison with the first excited states in {sup 95}Zr is also attempted. The addition of a neutron hole in {sup 96}Nb results in a much more fragmented level scheme.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Butt Laser Welding–Brazing of AZ31 Mg to Nickel-Coated Ti-6Al-4V

Mg and Ti alloy are hard to be bonded due to their huge discrepancy in physical and metallurgical characteristics. As an intermediate element, Ni is feasible for joining of Mg and Ti. The interfacial microstructure and mechanical properties of laser-welded–brazed AZ31 Mg/Ti-6Al-4V joints in butt configuration were investigated with different thicknesses of electrodeposited Ni interlayer. The interfacial reaction products evolved from an ultra-thin Ti{sub 3}Al layer to Ti{sub 2}Ni layer mingled with Ti{sub 3}Al, and more Mg{sub 3}AlNi{sub 2} compounds were produced in the fusion zone (FZ) as Ni coating thickness increased. Slag inclusions and cracks were observed in interfacial layer when coating thickness exceeded 2.5 μm. The quantity of Mg{sub 3}AlNi{sub 2} and the thickness of interfacial layer decreased from the top to bottom of groove of the same joint owing to high thermal gradient during laser welding. The chemical potential of Al and Ni indicated that Al-Ti reaction product was produced more easily than Ni-Ti in 0.001Mg-(Ni-Al-Ti) system. The thermodynamic calculation results of Gibbs free energy suggested the preferential formation Ti-Al phase and Ti-Ni phase along the interface while the Mg-Al-Ni ternary phase in the FZ. Fracture loads of joints increased first followed by a decline with the increase in coating thickness. The joint fractured at the Mg base metal, reaching a maximum value of 3900 N with the Ni coating thickness of 1.5 μm. In the case of using thinner or thicker Ni coating, crack propagated along the interface due to the insufficient metallurgical bonding or defects existed in the interfacial layer. The characteristic of fracture surface changed from the tear ridges and terraces to river pattern when interfacial failure occurred.

36 MATERIALS SCIENCE↗

Hydrogen Storage Performance of Preferentially Oriented Mg/rGO Hybrids

Chemical interactions on the surface of a functional nanoparticle are closely related to its crystal facets, which can regulate the corresponding energy storage properties like hydrogen absorption. In this study, we reported a one-step growth of magnesium (Mg) particles with both close- and nonclose-packed facets, that is, {0001} and {$2\overline{116}$} planes, on atomically thin reduced graphene oxide (rGO). The detailed microstructures of Mg/rGO hybrids were revealed by X-ray diffraction, selected-area electron diffraction, high-resolution transmission electron microscopy, and fast Fourier transform analysis. Hydrogen storage performance of Mg/rGO hybrids with different orientations varies: Mg with preferential high-index {$2\overline{116}$} crystal surface shows remarkably increased hydrogen absorption up to 6.2 wt % compared with the system exposing no preferentially oriented crystal surfaces showing inferior performance of 5.1 wt % within the first 2 h. First-principles calculations revealed improved hydrogen sorption properties on the {$2\overline{116}$} surface with a lower hydrogen dissociation energy barrier and higher stability of hydrogen atoms than those on the {0001} basal plane, supporting the hydrogen uptake experiment. In addition, the hydrogen penetration energy barrier is found to be much lower than that of {0001} because of low surface atom packing density, which might be the most critical process to the hydrogenation kinetics. Here, the experimental and calculation results present a new handle for regulating the hydrogen storage of metal hydrides by controlled Mg facets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗