Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Land Use Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Mapping of sea ice and measurement of its drift using aircraft synthetic aperture radar images

Side-looking radar images of Arctic sea ice were obtained as part of the Arctic Ice Dynamics Joint Experiment. Repetitive coverages of a test site in the Arctic were used to measure sea ice drift, employing single images and blocks of overlapping radar image strips; the images were used in conjunction with data from the aircraft inertial navigation and altimeter. Also, independently measured, accurate positions of a number of ground control points were available. Initial tests of the method were carried out with repeated coverages of a land area on the Alaska coast (Prudhoe). Absolute accuracies achieved were essentially limited by the accuracy of the inertial navigation data. Errors of drift measurements were found to be about + or - 2.5 km. Relative accuracy is higher; its limits are set by the radar image geometry and the definition of identical features in sequential images. The drift of adjacent ice features with respect to one another could be determined with errors of less than + or - 0.2 km.

Leberl, F.↗

Accelerated development and flight evaluation of active controls concepts for subsonic transport aircraft. Volume 2: AFT C.G. simulation and analysis

Relaxed static stability and stability augmentation with active controls were investigated for subsonic transport aircraft. Analytical and simulator evaluations were done using a contemporary wide body transport as a baseline. Criteria for augmentation system performance and unaugmented flying qualities were evaluated. Augmentation control laws were defined based on selected frequency response and time history criteria. Flying qualities evaluations were conducted by pilots using a moving base simulator with a transport cab. Static margin and air turbulence intensity were varied in test with and without augmentation. Suitability of a simple pitch control law was verified at neutral static margin in cruise and landing flight tasks. Neutral stability was found to be marginally acceptable in heavy turbulence in both cruise and landing conditions.

Urie, D. M.↗

Development of land based radar polarimeter processor system

The processing subsystem of a land based radar polarimeter was designed and constructed. This subsystem is labeled the remote data acquisition and distribution system (RDADS). The radar polarimeter, an experimental remote sensor, incorporates the RDADS to control all operations of the sensor. The RDADS uses industrial standard components including an 8-bit microprocessor based single board computer, analog input/output boards, a dynamic random access memory board, and power supplis. A high-speed digital electronics board was specially designed and constructed to control range-gating for the radar. A complete system of software programs was developed to operate the RDADS. The software uses a powerful real time, multi-tasking, executive package as an operating system. The hardware and software used in the RDADS are detailed. Future system improvements are recommended.

Kronke, C. W.↗

Lightweight Boom For Rescue Helicopter

Telescoping boom and associated mechanisms attached to helicopter aid rescue operations by extending lifeline beyond sweep of main rotor. Pilot observes rescuee and control position of helicopter more effectively than if rescuee directly below and hidden from pilot's view. Rescuee outside downdraft of rotor, which is often powerful enough to blow away or submerge someone in water. Used for marine or land operations. Boom thin and lightweight because it need not support weight of rescuee. Lifeline pulls away from boom after secured around rescuee, who is lifted directly into cabin by winch. Potential application for in situ erection of telescopic space structures.

Haslim, Leonard A.↗

Manual Manipulation of Engine Throttles for Emergency Flight Control

If normal aircraft flight controls are lost, emergency flight control may be attempted using only engines thrust. Collective thrust is used to control flightpath, and differential thrust is used to control bank angle. Flight test and simulation results on many airplanes have shown that pilot manipulation of throttles is usually adequate to maintain up-and-away flight, but is most often not capable of providing safe landings. There are techniques that will improve control and increase the chances of a survivable landing. This paper reviews the principles of throttles-only control (TOC), a history of accidents or incidents in which some or all flight controls were lost, manual TOC results for a wide range of airplanes from simulation and flight, and suggested techniques for flying with throttles only and making a survivable landing.

Burcham, Frank W., Jr.↗

Approach for Autonomous Control of Unmanned Aerial Vehicle Using Intelligent Agents for Knowledge Creation

This paper describes the development of a planned approach for Autonomous operation of an Unmanned Aerial Vehicle (UAV). A Hybrid approach will seek to provide Knowledge Generation thru the application of Artificial Intelligence (AI) and Intelligent Agents (IA) for UAV control. The application of many different types of AI techniques for flight will be explored during this research effort. The research concentration will be directed to the application of different AI methods within the UAV arena. By evaluating AI approaches, which will include Expert Systems, Neural Networks, Intelligent Agents, Fuzzy Logic, and Complex Adaptive Systems, a new insight may be gained into the benefits of AI techniques applied to achieving true autonomous operation of these systems thus providing new intellectual merit to this research field. The major area of discussion will be limited to the UAV. The systems of interest include small aircraft, insects, and miniature aircraft. Although flight systems will be explored, the benefits should apply to many Unmanned Vehicles such as: Rovers, Ocean Explorers, Robots, and autonomous operation systems. The flight system will be broken down into control agents that will represent the intelligent agent approach used in AI. After the completion of a successful approach, a framework of applying a Security Overseer will be added in an attempt to address errors, emergencies, failures, damage, or over dynamic environment. The chosen control problem was the landing phase of UAV operation. The initial results from simulation in FlightGear are presented.

Dufrene, Warren R., Jr.↗

Geopositional Accuracy Assessment of EarthSat Geocover Landsat Orthorectified Imagery

NASA purchased EarthSat GeoCover orthorectified Landsat imagery of global land areas covering three historical frames: (1) mid-1970's imagery from the Landsat Multispectral Scanner (MSS); (2) late 1980's-early 1990's imagery from the Landsat Thematic Mapper (TM); and (3) year 2000 imagery from the Landsat Enhanced Thematic Mapper Plus (ETM+). Because of the distinct time frames covered by these datasets, this imagery is valuable to land cover change research. Because geopositional accuracy plays a critical role in this area of scientific research. NASA performed an independent assessment of the geopositional accuracy of each EarthSat dataset using an independent set of government-provided ground control points (GCPs). These points were instrumental in the geopositional accuracy assessment of the TM imagery. Because of the orthorectification processes of the MSS imagery and the MSS pixel size, the aforementioned GCPs could not be used, and an alternate relative assessment procedure using the previously validated TM imagery as a "truth" dataset was used for the MSS data. Finally, the ETM data specification was defined in both an absolute sense with respect to ground coordinated and relative to the previously validated TM dataset. Therefore, two separate methods were used in validating the ETM-data. Results of the NASA independent assessments showed that the accuracies of the EarthSat GeoCover datasets met the defined specifications or were within the error and limitations of the verification methods employed.

Smith, Charles M.↗

Functional Task Test: 3. Skeletal Muscle Performance Adaptations to Space Flight

The functional task test is a multi-disciplinary study investigating how space-flight induced changes to physiological systems impacts functional task performance. Impairment of neuromuscular function would be expected to negatively affect functional performance of crewmembers following exposure to microgravity. This presentation reports the results for muscle performance testing in crewmembers. Functional task performance will be presented in the abstract "Functional Task Test 1: sensory motor adaptations associated with postflight alternations in astronaut functional task performance." METHODS: Muscle performance measures were obtained in crewmembers before and after short-duration space flight aboard the Space Shuttle and long-duration International Space Station (ISS) missions. The battery of muscle performance tests included leg press and bench press measures of isometric force, isotonic power and total work. Knee extension was used for the measurement of central activation and maximal isometric force. Upper and lower body force steadiness control were measured on the bench press and knee extension machine, respectively. Tests were implemented 60 and 30 days before launch, on landing day (Shuttle crew only), and 6, 10 and 30 days after landing. Seven Space Shuttle crew and four ISS crew have completed the muscle performance testing to date. RESULTS: Preliminary results for Space Shuttle crew reveal significant reductions in the leg press performance metrics of maximal isometric force, power and total work on R+0 (p<0.05). Bench press total work was also significantly impaired, although maximal isometric force and power were not significantly affected. No changes were noted for measurements of central activation or force steadiness. Results for ISS crew were not analyzed due to the current small sample size. DISCUSSION: Significant reductions in lower body muscle performance metrics were observed in returning Shuttle crew and these adaptations are likely contributors to impaired functional tasks that are ambulatory in nature (See abstract Functional Task Test: 1). Interestingly, no significant changes in central activation capacity were detected. Therefore, impairments in muscle function in response to short-duration space flight are likely myocellular rather than neuromotor in nature.

Ryder, Jeffrey W.↗

Identifying Common Coordination Procedures across Extensible Traffic Management (xTM) to Integrate xTM Operations into the National Airspace System

New categories of missions and vehicle types, such as drone delivery services, on-demand air taxi, and high-altitude long-endurance (HALE) vehicles are being proposed to operate using a novel, highly automated information exchange infrastructure and a community-based, cooperative traffic management concept. Collectively, these new operations are called Extensible Traffic Management (xTM). As these xTM vehicles become more prevalent, their operations will increasingly overlap with existing conventional aircraft and with each other. In order to seamlessly co-exist with current conventional aircraft operations, new coordination procedures, tools and services will be needed to integrate xTM into the future National Airspace System (NAS). In our prior work, we have identified a set of use cases for xTM interactions with air traffic control (ATC), categorized across different xTM operations based on trigger events. Events consisted of ones such as nominal xTM vehicle transition into the ATC environment or an off-nominal emergency landing situation. In this paper, we have extended the prior work to identify commonalities in the coordination procedures across xTM, as well as differences that are specific to the individual xTM operations. The overall results showed that two types of xTM-ATC interactions were prevalent: 1) xTM vehicles transitioning between xTM and ATC operational environments; 2) xTM vehicles being allowed to continue xTM operations in areas that are normally controlled by ATC. The results also suggested that emergency and rare off-nominal events may need specialized procedures for each vehicle type. The overall results suggest that there is a pathway to define a common method of handling and integrating diverse xTM operations in the future NAS, but there need to be procedures for individualized handling of xTM vehicles in infrequent, safety-critical events.

Extensible Traffic Management (xTM)↗

GIS-Based Modeling of Contaminated Soil Volumes at Multiple Sites in the Formerly Utilized Sites Remedial Action Program - 20149

The remediation of hazardous, toxic, and radioactive waste (HTRW) sites produces cost-related risks associated with the estimation of contaminated soil or debris volumes. Historical risk-management techniques include cost contingencies to cover volume uncertainties that affect project budgeting and decision-making. The Buffalo District teamed with project partners to lessen volume uncertainty and reduce project risks at multiple HTRW sites managed under the Formerly Utilized Sites Remedial Action Program (FUSRAP). Historical remedial investigations under FUSRAP commonly identified the presence of radiological material in site media, the associated human health risk, and then areas of remediation. To manage remedial execution and reduce risk, pre-design or remediation-phase sampling essentially 'chased' contamination, which was not conducive to efficient predictive budgeting derived from Feasibility Study (FS) cost analyses. The Buffalo District first optimized their approach to better understand volume uncertainty by utilizing the Argonne National Laboratory's Bayesian Approaches for Adaptive Spatial Sampling (BAASS) software [1]. BAASS processed soft data (e.g., gamma walk-over data) and spatial sampling data to estimate the lateral extent of contaminated soil irrespective of depth (i.e., gross contamination extent) and define areas of contaminant uncertainty. The software performed a binary transformation of contaminant concentrations at all sampling points based upon remedial action goals or a sum of ratios approach (i.e., clean, impacted, or range of impacts in soil). The model produced two-dimensional (horizontal) contaminant probability contours and statistical uncertainty in the sampling coverage and resulting contaminant extents. This method was translated vertically by partitioning the sampling data into depth brackets that produced a stacked representation of contaminant extents and uncertainty in the subsurface (i.e., similar to construction lifts). The results commonly led to a better understanding of project uncertainty and the need for sampling strategies that produce high-confidence soil volumes, which control costs. The BAASS-based delineations were eventually replaced by Empirical Bayesian Kriging (EBK) methods available in ArcGIS Spatial or 3D Analysts [2]. The EBK method calculates contaminant probability zones derived from user-controlled semivariograms of the spatial datasets. The resulting probability zones (e.g., 50% or 80% of contaminant probability) represent the two-dimensional surface delineation of the overall horizontal remedial area, similarly to BAASS. However, unlike BAASS, the vertical sampling data within these probability zones became vertical control points to contour a subterranean surface that connects subsurface points to the land-surface delineations of contamination. The resulting representation of horizontal and vertical impacts within an enclosed envelop (volume) of soil included uncertainty distributions that are used to plan uncertainty-reduction sampling. These data-driven and math-based models of three-dimensional sampling results produced well-bounded remedial volumes for project planning and better uncertainty predictions during project budgeting. The EBK method was applied to several FUSRAP sites managed by the Buffalo District and compared to less rigorously modeled sites previously remediated by the District. The comparison of modeled to actual remediated volumes provide a basis for validating the volume-estimation method. This comparison is important to ensure modeled volumes match physical boundaries of site remediation. FUSRAP sites with denser investigative sampling and lesser volume uncertainty proved useful in remedial planning and contracting. The Buffalo District noted that historical sites with sparser sampling arrays had greater disparity between estimated volumes and final remedial volumes. The benefit achieved over the cost of detailed soil sampling appears positive for FUSRAP projects, especially where impacts vary widely and appear unbounded by investigation-phase sampling. The subsequent Empirical Bayesian Kriging of contamination coupled with vertical contouring for soil estimations reduces uncertainty in soil volumes or indicates where sampling is required to reduce uncertainty, which together optimize remedial planning and budgeting. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Momentum-Based Indicator for Predicting the Peak Opening Load of Supersonic Parachutes

In this paper, a new empirical indicator for predicting the peak opening loads of supersonic parachutes is presented. The proposed indicator is proportional to twice the free-stream dynamic pressure and the projected area of the parachute, which is equivalent to estimating the opening load as a percentage of the free-stream momentum flux through the projected area at the moment of peak inflation. The form of this expression is motivated by a classical control volume analysis of the aerodynamic forces acting on a parachute during inflation, under the simplifying assumptions of quasi-static and one-dimensional flow. For parachute geometries and flight conditions typical of Mars Entry, Descent, and Landing systems, the largest contribution to the total drag is shown to be a momentum flux term that is associated with the entrainment of atmosphere within the inflating parachute volume. Using this new method, empirical constants are calculated from existing flight reconstruction data and are shown to have a smaller standard deviation than similar constants determined using the customary indicator form, which is based on the steady-state subsonic drag and proportional to the parachute reference area. These empirical constants are also compared to an analytic estimate, derived from the control volume analysis, and shown to have excellent agreement across a wide range of Mach numbers and dynamic pressures for several parachute geometries. While opening loads estimated using both methods produce similar results at low supersonic Mach numbers typical of past inflations, the proposed method predicts notably larger loads at higher Mach numbers, those above Mach 2.0, due to the omission of any Mach Efficiency Factor. Several current Mars EDL projects have adopted this new indicator.

Way, David W.↗

Improving and testing machine learning methods for benchmarking soil carbon dynamics representation of land surface models

Representation of soil organic carbon (SOC) dynamics in Earth system models (ESMs) is a key source of uncertainty in predicting carbon climate feedbacks. The magnitude of this uncertainty can be reduced by accurate representation of environmental controllers of SOC stocks in ESMs. In this study, we used data of environmental factors, field SOC observations, ESM projections and machine learning approaches to identify dominant environmental controllers of SOC stocks and derive functional relationships between environmental factors and SOC stocks. Our derived functional relationships predicted SOC stocks with similar accuracy as the machine learning approach. We used the derived relationships to benchmark the coupled model intercomparison project phase six ESM representation of SOC stocks. We found divergent environmental control representation in ESMs in comparison to field observations. Representation of SOC in ESMs can be improved by including additional environmental factors and representing their functional relationships with SOC consistent with observations.

54 ENVIRONMENTAL SCIENCES↗

Future of Fuel Savings

Using automation to free up controllers for more strategic management of air traffic is one approach being studied by NASA as it seeks to boost airspace system capacity and efficiency, thereby saving fuel. Heinz Erzberger, a NASA Ames Research Center senior scientist, says the Advanced Airspace Concept (AAC) has been studied for several years. It could increase efficiency 15% by providing optimal routes that cut airlines direct operating costs. A 25% increase in landings on existing runways could follow an important benefit. AAC is one of the efforts to be reviewed by the Joint Planning and Development Organization, an FAA-led initiative by six federal agencies to redesign the U.S. air transportation system by 2025. The main goal is to triple air traffic capacity within 20 years to avert the sort of gridlock that would make fuel consumption only one of many travel nightmares. The automated system approach would allow aircraft to fly optimal trajectories. A trajectory would be defined in the standard three dimensions and eventually include the fourth, time. The management of air traffic by the data-linked exchange of trajectories would start at high altitude and eventually move down to lower altitudes. The automated concept is an outgrowth of the type of tools developed by NASA for use by FAA controllers in managing traffic flows over the years, including ones that optimize routings for the best fuel burn. But AAC would push automation further to reduce workload so controllers can focus on "solving strategic control problems, managing traffic flow during changing weather and ... other unusal events." One key component, the automated trajectory server (ATS), is a ground systems that would rely on software to manage flight path requests from aircrews and controllers. But, Erzberger acknowledges, "The FAA's current plan for upgrades to air traffic services does not include [allowing] the future ground system to issue separation-critical clearances of trajectory changes autonomously to aircraft via data link without explicit approval of a controller," as the AAC proposes. The AAC enables pilots or controllers to data link requests for a trajectory change to the ATS for approval after they are deconflicted with the paths of other aircraft. To divert around storms, for example, pilots could data link their trajectory preference to the ATS. Since several aircraft might request similar routes, the computer would then have to suggest alternatives. This could be accomplished without pilot-controller radio calls, a big bottleneck now. The ATS would have a built-in conflict monitor to call for a resolution (turn, climb or descend), when loss of separation is likely in 1-20 min. The AAC system would reduce controller errors by 90%, according to NASA Ames estimates. The AAC would have a back-up program to assure separation-Tactical Separation Assurance (TSAFE). It s designed to detect short-term traffic conflicts within 3-4 min. of loss of separation. The last line of defense would still be provided by traffic alert & collision avoidance systems (TCAS).

Hughes, David↗

Soil management practices can contribute to net carbon neutrality in California

Stabilizing climate requires reducing greenhouse gas (GHG) emissions and storing atmospheric carbon dioxide (CO 2 ) in land or ocean systems. Soil management practices can reduce GHG emissions or sequester atmospheric CO 2 into inorganic and organic forms. However, whether soil carbon strategies represent a viable and impactful climate mitigation pathway is uncertain. A specific question concerns the role that land-management practices and soil amendments can play in realizing California's ambition for carbon neutrality by 2045. Here we examine the carbon flux impacts of soil conservation (i.e., compost, reduced tillage, cover crop) and enhanced silicate rock weathering (EW) practices at different areal extents of implementation in cropland, grassland, and savanna in California under two climate change cases. We show that with implementation areas of 15% or 50% of private cultivated land, grassland, and savanna in California, soil conservation practices alone can contribute $1.4^{2.1}_{0.7}$% ($-1.8^{-2.7}_{ -0.9}$ Mt CO 2 eq y -1 ) and $4.6^{6.9}_{2.3}$% ($-6.0^{-8.9}_{-3.0}$ Mt CO 2 eq y -1 ) of the additional emissions reduction needed (beyond previous targets) to meet the 2045 net neutrality goal (-129.3 Mt CO 2 eq y -1 ), respectively, on an average annual basis, including climate uncertainty. Including EW in these scenarios increases the total contributions of management practices to $4.1^{5.6}_{2.5}$% ($-5.2^{-7.3}_{-3.2}$ Mt CO 2 eq y -1 ) and $13.5^{18.6}_{8.2}$% ($-17.5^{-24.2}_{-10.7}$ Mt CO 2 eq y -1 ), respectively, of this reduction. This highlights that the extent of implementation area is a major factor in determining benefits and that EW has the potential to make a real contribution to net reduction targets. Results are similar across climate cases, indicating that contemporary field data can be used to make future projections. With EW there remains mechanistic uncertainties, however, such as rock dissolution rate and environmental controls on weathering products, which require additional field research to improve understanding of the technological efficacy of this approach for California's 2045 carbon neutrality goal.

54 ENVIRONMENTAL SCIENCES↗

Six-degree-of-freedom guidance and control-entry analysis of the HL-20

The ability of the HL-20 lifting body to fly has been evaluated for an automated entry from atmospheric interface to landing. This evaluation was required to demonstrate that not only successful touchdown conditions would be possible for this low lift-to-drag-ratio vehicle, but also the vehicle would not exceed its design dynamic pressure limit of 400 psf during entry. This dynamic pressure constraint limit, coupled with limited available pitch-control authority at low supersonic speeds, restricts the available maneuvering capability for the HL-20 to acquire the runway. One result of this analysis was that this restrictive maneuvering capability does not allow the use of a model-following atmospheric entry-guidance algorithm, such as that used by the Space Shuttle, but instead requires a more adaptable guidance algorithm. Therefore, for this analysis, a predictor-corrector guidance algorithm was developed that would provide successful touchdown conditions while not violating the dynamic pressure constraint. A flight-control system was designed and incorporated, along with the predictor-corrector guidance algorithm, into a six-DOF simulation. which showed that the HL-20 remained controllable and could reach the landing site and execute a successful landing under all off-nominal conditions simulated.

Powell, Richard W.↗

Background and current status of the lifting body program

The lifting body concept was originally conceived by the Ames Research Center, and the design was developed over a period of years, from 1957 to 1964. By using a cone as a basic entry shape and modifying it to obtain lift and control, the M-2 shape evolved. In a cooperative venture with the NASA Ames Research Center to determine if a pilot could maneuver, flare, and land this class of vehicle, the Flight Research Center constructed a lightweight version of the lifting body, the M2-F1 vehicle. This vehicle was constructed during the fall of 1962 and spring of 1963 and extensively flight tested during the summer of 1963. Because of the success of the M2-F1 flight program, the research program was extended to include vehicles that would be representative of mission weight and wing loading. Figure 1 shows the three vehicles in the present lifting body program. On the left is the X-24A vehicle, which evolved from the U. S. Air Force's SV-5 PRIME vehicle; in the center is the M2-F3 vehicle, which is a modified version of the M2-F2 vehicle; and on the right is the HL-10 vehicle, which evolved from work at the NASA Langley Research Center.

John G McTigue↗

Estimating Airline Operating Costs

The factors affecting commercial aircraft operating and delay costs were used to develop an airline operating cost model which includes a method for estimating the labor and material costs of individual airframe maintenance systems. The model permits estimates of aircraft related costs, i.e., aircraft service, landing fees, flight attendants, and control fees. A method for estimating the costs of certain types of airline delay is also described.

Maddalon, D. V.↗

Application of an integrated flight/propulsion control design methodology to a STOVL aircraft

Results are presented from the application of an emerging Integrated Flight/Propulsion Control (IFPC) design methodology to a Short Take Off and Vertical Landing (STOVL) aircraft in transition flight. The steps in the methodology consist of designing command shaping prefilters to provide the overall desired response to pilot command inputs. A previously designed centralized controller is first validated for the integrated airframe/engine plant used. This integrated plant is derived from a different model of the engine subsystem than the one used for the centralized controller design. The centralized controller is then partitioned in a decentralized, hierarchical structure comprising of airframe lateral and longitudinal subcontrollers and an engine subcontroller. Command shaping prefilters from the pilot control effector inputs are then designed and time histories of the closed loop IFPC system response to simulated pilot commands are compared to desired responses based on handling qualities requirements. Finally, the propulsion system safety and nonlinear limited protection logic is wrapped around the engine subcontroller and the response of the closed loop integrated system is evaluated for transients that encounter the propulsion surge margin limit.

Garg, Sanjay↗