Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Inclusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser-induced slip casting as an additive manufacturing approach for silicon carbide

Here, this work presents processing silicon carbide (SiC) with the laser-induced slip casting (LIS) additive manufacturing (AM). SiC was stabilized in water with polyethyleneimine (PEI) dispersant, and SiC slurries were made with rheology for LIS printing. High-density ceramic parts were printed, followed by single-step binder burnout and sintering. The printed parts achieved 93–95 % of theoretical density. X-ray computed tomography (XCT) revealed a small distribution of flaws exceeding 100 microns. The mechanical properties were measured in both parallel and perpendicular to the printing layers, and the orientation with layers perpendicular to the bending moment resulted in higher strength compared to the parallel direction. Porosity resulting from processing and large inclusions of boron carbide (B4C) were the root cause of failure in the measured samples. Despite these defects through this effort, this new approach demonstrates promise for green forming of SiC with densities greater than 95 % theoretical and tensile strengths above 250 MPa.

Additive Manufacturing↗
DOE OSTI2026

3D analysis of abnormal grain growth in calcia doped alumina in the presence of large pores

Abnormal grain growth has been previously found to increase with the inclusion of large pores (∼60 µm in diameter) in 80 ppm calcium doped alumina. However, the two-dimensional analysis could not accurately describe the proximity of the abnormal grains and pores to establish a correlation. This study uses laboratory-based diffraction contrast tomography and x-ray computed tomography to spatially map the pores and abnormal grains in 3D. A preference towards the formation of abnormal grains near large pores is found when compared to all potential sites. This finding supports that the pores may be a nucleation site for complexion transitions that promote abnormal grain growth. The growth of the abnormal grains in a subsequent heat treatment at 1600°C for 16 hrs was also studied. The elongation along the principal axes is similar for both small and large grains, again supporting that abnormal grain growth was facilitated by a complexion transition.

Abnormal grain growth↗
DOE OSTI2025

A review on advances in oxidative coupling of methane (OCM) for industrial use and prospects of CO 2 –H 2 O splitting integration

The discovery of shale gas reserves has encouraged the development of direct methods for methane conversion into valuable chemicals, offering an alternative to indirect approaches that involve an energy-intensive and intermittent syngas production step, leading to high CO 2 emissions. Amongst the direct methods, the oxidative coupling of methane (OCM) is a potential pathway to reduce CO 2 emissions and can produce commodity chemicals such as ethylene, a chemical regarded as central to the petrochemical industry. Even though OCM has been studied for over four decades, the technology still has not found commercial application. Amongst the challenges regarding industrial deployment of OCM, the most significant one is the requirement of a high ethylene yield of 30 % which is currently reported to be around 20 %. Moreover, the highly exothermic nature of the process and controlling the carbon selectivity over oxides of carbon (COx) is the heart of the problem. Numerous researchers have presented promising results in terms of catalysts, reactor designs and feeding strategies for OCM. However, due to lack of inclusiveness in the results, none of the combination of catalysts, reactors and system optimizations has been able to bring about its industrial viability. The current paper presents an extensive review of the noteworthy attempts to achieve industrial targets for OCM. Moreover, a comprehensive criteria is presented which highlights the desired end state for the industrial deployment of OCM technology. Furthermore, the criteria is based on literature survey and a comparison with industrially deployed ethylene production plants i.e., naphtha or ethane steam cracker plants. Finally, a novel integration technology is presented which includes a combination of OCM and CO 2 -H 2 O splitting in a chemical looping reactor design to enable efficient energy utilization and minimal heat losses to the environment.

CO2 Splitting↗
DOE OSTI2020

Impact of Cr and Co on 99Tc retention in magnetite: A combined study of ab initio molecular dynamics and experiments

This work explores the effect of co-mingled dopants, Co(II) and Cr(III), on Tc(IV) incorporation and retention in magnetite when heat treated to 625 or 700 °C. Key trends in Tc retention in the high temperature regime were identified using a combination of density-functional-theory based ab initio molecular dynamics (AIMD) simulations, and batch experiments including solid phase characterization techniques, e.g. X-ray absorption spectroscopy. A stabilizing effect on Tc(IV) was observed when the number of Tc and Cr atoms are equal or when the magnetite surface is oversaturated with Tc and Cr inclusions. Here, oversaturation is hypothesized to force Cr from the magnetite surface to form a Cr2O3 phase, which may act as a protective layer that prevents Tc release. With the addition of Co, Tc(IV) is stabilized via redox processes. The presence of Cr in low concentrations interferes with this redox stabilization and Cr is preferentially stabilized as opposed to Tc. As a result, using Co as a stabilizing dopant for Tc may be compromised in the presence of Cr. When the relative concentration of Tc, Cr and Co is the same, or more Co atoms are added to high Cr incorporated systems, the formation of the Cr2O3 phase may be suppressed. Although waste streams with co-mingled Tc and Cr potentially may benefit from a Co dopant, since the formation of a Cr2O3 passivation layer may protect incorporated Tc from being released, the relative concentration of the three elements will be a critical parameter for maximizing effectiveness of this strategy.

Lee, Mal Soon↗
DOE OSTI2022

Updated neutrino mass constraints from galaxy clustering and CMB lensing-galaxy cross-correlation measurements

In this work, we revisit cosmological constraints on the sum of the neutrino masses Σm v from a combination of full-shape BOSS galaxy clustering [P(k)] data and measurements of the cross-correlation between Planck Cosmic Microwave Background (CMB) lensing convergence and BOSS galaxy overdensity maps [$C_{l}^{kg}$], using a simple but theoretically motivated model for the scale-dependent galaxy bias in auto- and cross-correlation measurements. We improve upon earlier related work in several respects, particularly through a more accurate treatment of the correlation and covariance between P(k) and $C_{l}^{kg}$ measurements. When combining these measurements with Planck CMB data, we find a 95% confidence level upper limit of Σm v sum of neutrino masses < 0.14 eV, while slightly weaker limits are obtained when including small-scale ACTPol CMB data, in agreement with our expectations. We confirm earlier findings that (once combined with CMB data) the full-shape information content is comparable to the geometrical information content in the reconstructed BAO peaks given the precision of current galaxy clustering data, discuss the physical significance of our inferred bias and shot noise parameters, and perform a number of robustness tests on our underlying model. While the inclusion of $C_{l}^{kg}$ measurements does not currently appear to lead to substantial improvements in the resulting Σm v of neutrino mass constraints, we expect the converse to be true for near-future galaxy clustering measurements, whose shape information content will eventually supersede the geometrical one.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Recent advances in integrated hydrologic models: Integration of new domains

Over the past several decades, hydrologic models have advanced from independent models of the surface and subsurface to integrated models that can capture the terrestrial hydrologic cycle within one framework. In recent years, these coupled frameworks have seen the inclusion of biogeochemical processes, ecohydrology, sedimentation and erosion, cold region hydrology, anthropogenic activities, and atmospheric processes. This expansion is the result of increased computational, data, and modeling capabilities and capacities, as well as improved understanding of the processes that drive these integrated systems. Here, in this study, we review these recent advances to integrate new processes and systems into existing terrestrial hydrologic models and highlight the significant challenges and opportunities that remain. We identify that with so many models currently available and in development, selecting the most appropriate model is difficult, and we suggest a path for new or novice modelers to find the most appropriate code based on their needs. In addition, data required to parameterize and calibrate these models can often constrain their applicability and usefulness. However, advances in environmental sensors and measurement technology, in addition to data assimilation of non-traditional data (e.g. remote sensing, qualitative data) are providing new ways of addressing this issue. As we expand hydrologic models to integrate more processes and systems, our computational demands also increase. Recent and emerging advances in computational platforms, including cloud and quantum computing, in addition to the use of machine learning to capture some processes, will continue to support the use of increasingly larger and more complex, process-based models. Finally, we highlight that it is critical to develop state-of-the-science models that are accessible to all model users, not just those applied for research and development. We encourage continued development of diverse modeling platforms, considering the user needs, data availability, and computational resources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Influence of oxygen on performance of multi-principal element alloy as braze filler for Ni-base alloys

In manufacturing of multi-principal element alloys (MPEAs), the casting process is often a primary point of oxygen introduction to the material system, which was demonstrated by the laboratory scale button arc-melting process. Oxygen introduction raises concerns for the mechanical performance of these alloys if employed as structural materials alone or in engineering applications, such as serving as filler materials to enable joining of similar or dissimilar alloy pairs that are conventionally considered difficult to join. In this work, oxide inclusions in an as-cast off-equiatomic MnFeCoNiCu MPEA and Ni-base alloy braze joints made with this MPEA were evaluated by synchrotron x-ray diffraction mapping and electron microscopy. MnO was found to be prevalent throughout the cast MPEA and was chemically reduced during brazing by trace Al from the base material, Ni-base Alloy 600. Incomplete reaction of the MnO with Al, and some alternative reaction with Cr, left a mixture of MnO, Al 2 O 3 , and Cr 2 O 3 in the as-brazed joint, with the oxides concentrated near the braze centerline due to directional solidification. Further, in the braze joints, the non-oxide constituent phases detected were an FCC matrix and particles of Cr 23 C 6 , Cr 7 C 3 , and TiN which are all native to Alloy 600. The evolution of oxides within the brazed joints at elevated service temperatures of 600-800°C was also evaluated. While MnO and Al 2 O 3 were stable during high-temperature service, Cr 2 O 3 particles grew to several hundred microns, with dissolved oxygen in the MPEA providing a significant source for oxide growth. Comparing tensile performance of the as-brazed condition with post-service conditions showed that the evolution of oxide particles contributed to an increase in strength and decrease in ductility of the brazed joints. Evaluating particle morphologies among fracture surfaces of individual specimens demonstrated that large Cr 2 O 3 particles and continuous cluster networks of Al 2 O 3 were the features most detrimental to total elongation. Hence, unmitigated evolution of oxygen-containing species during brazing and service conditions is detrimental to the ductility of the brazed joints, which highlights the importance of oxygen control in initial manufacturing of MPEAs for engineering applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-pressure deformation of metallic glass nanoparticles

Here, the atomistic structure of metallic glasses is closely related to properties such as strength and ductility. Here, Ni 1-x B x metallic glass nanoparticles of two different sizes are compressed under quasi-hydrostatic high-pressure conditions in order to understand structural changes under stress. The structural changes in the nanoparticles were tracked using in situ high-pressure X-ray diffraction (XRD). The ambient pressure pair distribution functions generated from XRD showed that the smaller sized nanoparticles had a more compact amorphous structure with lower coordination number. XRD showed that the amorphous structure was stable up to the maximum pressures achieved. The bulk modulus of the smaller and larger sized nanoparticles was found to be 208 GPa and 178 GPa, respectively. This size-dependent high-pressure behavior was related to compositional differences between the nanoparticles. These results show that Ni 1-x B x metallic glass nanoparticles are highly stable under pressure, which could enable their use as inclusions in metal or ceramic matrix composites.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure analysis of laser beam weldments performed on neutron-irradiated 304L steel containing 3 and 8 appm helium

We report that AISI 304 L austenitic stainless steel is one of the major structural materials used in light water reactors (LWRs). In the future, 304 L components may require repair, and several welding techniques have been proposed as candidates. In this study, laser beam welding using the low-energy contribution approach was performed in ~2016 on neutron-irradiated AISI 304 L steel with nominal values of 3 and 8 appm helium (He). The goal was to investigate the impact of helium on the irradiated material weldability and evaluate helium-associated damage. The weld and heat-affected zone (HAZ) microstructure was studied using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy (TEM). Analysis of the weldment cross-sections did not reveal severe cracking. Still, evidence of incipient helium-associated damage was observed in the HAZ, manifesting as degraded grain boundaries (GBs) “decorated” by pore chains and mostly small (i.e., ≤ 25-30 µm) scattered cracks. The largest observed crack was ~50 µm in length. Helium-associated damage was localized within ~200-300 µm of the weld pool boundary, and the fraction of the compromised GBs, as a rule, was below ~9-11% of the total GB network. TEM analysis showed significant annealing of the radiation-induced defects at distances up to ~300 µm from the weld pool boundary. Inside the HAZ, the cavities (likely, helium bubbles) tended to form at GBs and inclusions, such as manganese sulfide precipitates in the grain interior. Crystallography analysis of the HAZ damage showed that random high-angle boundaries were most susceptible to helium-associated damage. In contrast, low-angle random boundaries and twin boundaries appeared to be strongly resistant to degradation from the combined effects of helium and welding.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Possible impacts of Mo chemical banding and second phase impurities on the irradiation behavior of monolithic U-10Mo fuels

This study investigated the microstructural behavior of both full-size and mini-size monolithic U-10Mo fuel plates irradiated to high burnup with a focus on the evolution of the second phase impurities in monolithic U-Mo using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and wavelength dispersive spectroscopy (WDS). Key indicators of possible mechanical and thermal compromise include cracks, large fission gas porosity, and interconnection of fission gas pores. For the fission densities evaluated in this work (3.5 × 10 21 fissions/cm 3 -5.1 × 10 21 fissions/cm 3 ), fine porosity can develop along the UC phase boundary; however, the size of the fission gas pores is no more than those observed in the U-Mo fuel phase. Further, other inclusions such as Si-rich second-phase impurities found in the as-fabricated microstructure were difficult to resolve post-irradiation because they can become overshadowed by porosity development in the fuel phase. Additionally, the presence of a Fe-rich sublayer formed in the Zr diffusion layer during fabrication remained enriched in the Zr layer in the irradiated U-10Mo microstructures near the U-Mo/Zr interface; however, based on the burnup assessed in this study the identified impurities did not appear to contribute to notable microstructural degradation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Optical vibrational spectroscopic signatures related to U 3 O 8 production processes

Uranium ore concentrates are materials found early within the nuclear fuel cycle and contain high concentrations of uranium in an easily transported form, making the concentrates a likely target for illegal diversion. These concentrates are typically converted to U 3 O 8 for further processing and, therefore, may lose specific physicochemical characteristics in determining the materials’ source and processing history. In this work, we explore the Raman spectra of eight oxide samples produced from various uranium ore concentrates and processing pathways to examine the presence of spectroscopic signatures relating to each sample's process history. Samples produced from amine extraction and dialkylphosphoric acid extraction processes show unique characteristics due to high concentrations of α-UO 3 , whereas samples calcinated from metallic diuranates do not form pure α-U 3 O 8 because of metallic ion inclusions. Pure α-U 3 O 8 oxide samples are obtained through calcination of ammonium diuranate, ammonium uranyl carbonate, and metastudtite intermediates. The Raman spectra of these oxide samples show close agreement with pristine α-U 3 O 8 spectra. However, deviations from the pristine spectra are observed in the 300–460 cm -1 spectral range. In conclusion, these deviations are unique identifying signatures that were likely created by lasting effects from the process history. Spectral center of mass calculations indicate grouping of samples based on processing history.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Radiation damage study of POCO ZXF-5Q graphite for neutrino production targets using 4.5 MeV helium ions

To address the challenges of increased beam power and target survivability associated with next-generation particle production beam lines, high dose, high-energy proton beam conditions are simulated using irradiation from low-energy ion beams. A low-energy ion irradiation study of POCO ZXF-5Q graphite under conditions similar to those of the NuMI NT-02 neutrino production target at the Fermi National Accelerator Laboratory is reported. Helium ion irradiation was performed at 100 ∘ C to a maximum damage level of 0.9 displacements per atom (DPA). Irradiation induced hardening, swelling of the irradiated region, inter-plane lattice expansion, and intraplane lattice contraction with increasing ion fluence was observed using micromechanical (nanoindentation, atomic force microscopy) and electron microscopy (high-resolution imaging, selected area diffraction) characterization. Similar changes were also observed in post irradiation examination of the NT-02 target indicating that ion irradiation can be a valuable tool for estimating radiation damage in proton beam targets. Caution must be exercised though, because the hardening, lattice alteration, and swelling occur to different magnitudes for a given damage level. The observed hardening and embrittlement were greater for ion irradiated graphite. For He ion irradiated samples the lattice spacing changes were smaller at low damage levels (78% less expansion and 71% less contraction at 0.1 DPA) and larger at high damage levels (38% more expansion and 5% more contraction at 0.9 DPA) relative to that observed in the NT-02 target. The magnitude of swelling was 8.5× greater under ion irradiation which is influenced by the differing damage gradients and inclusion of implanted He ions in the region of interest.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Changes in dislocation punching behavior due to hydrogen-seeded helium bubble growth in tungsten

The accumulation of gas atoms in tungsten is a topic of long-standing interest to the plasma-facing materials community due the metal's use as a divertor material in some tokamak fusion reactors. The nucleation and growth of He/H gas bubbles (along with their isotopes) can result from impinging fluxes of these gases which give rise to damage at the W divertor surface. The inclusion of He or H in W has been studied extensively by the community, finding that He bubbles modify the surface through periodic dislocation punching and bursting mechanisms while H bubbles impact the metal through plastic-strain induced material failure. However, the mechanisms which are present during the combined flux of both He and H is not well-studied atomistically. Motivated by this, an atomistic modeling study is conducted using molecular dynamics to assess the behavior of mixed concentration He:H bubbles in W. Here we find that the introduction of H into a growing He bubble results in a dramatic change in the nature and presence of dislocation loops which are typically generated via dislocation punching in over-pressurized He bubbles. Most notably, at high H concentrations, there is a switchover in energetic favorability from glissile 1/2<111> dislocations to sessile <100> dislocations. This thermodynamic crossover could imply a significant reduction in W surface morphology changes than with pure He bubbles and, additionally, we show this to have implications on the trapping of H in the bubbles and their associated dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enabling BWR fuel rod analysis in the BISON fuel performance code

Nuclear fuel vendors around the world are pursuing approaches to sustain the existing nuclear reactor fleet consisting primarily of pressurized-water reactors (PWRs) and boiling-water reactors (BWRs). To support the industry's efforts, advanced modeling and simulation tools need to be capable of analyzing both legacy reactor concepts. BWR fuel rods are significantly different than those used in PWRs, which can affect fuel performance analysis. BWR fuel rods include: (1) an extensive use of gadolinia dopant as a burnable absorber, (2) an axial variation in fuel enrichment and gadolinia content, (3) the inclusion of a liner on the inner cladding surface to mitigate the impact of pellet-clad mechanical interaction (which impacts hydrogen and hydride distribution), (4) a lower initial fill gas pressure, (5) bottom-entry control rods, and (6) a lower coolant pressure that results in the two-phase flow boiling phenomenon. Although the primary focus of BISON has been in the area of PWR and advanced reactor fuel analyses, this paper presents the developments in BISON to support BWR fuel performance analysis. An overview of the models that account for the effects of gadolinia is highlighted. Internal mesh generation capabilities to include a liner is presented. Normal operating and transient (reactivity insertion accident) demonstration problems are presented to illustrate the impact of gadolinia, the hydrogen and hydride evolution due to the presence of the liner, and BISON's ability to simulate axially varying enrichments and dopant concentration. Bottom-entry control effects are captured by the axial power peaking factors present in the demonstration cases. Comparisons to integral experiments from the Halden IFA-681 experiments are discussed as initial validation. Reasonable comparisons are obtained for fuel centerline temperature and rod internal pressure as a function of time. In conclusion, simulations of additional experiments containing Gd 2 O 3 -bearing fuel are necessary to completely validate the code for BWR applications.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Anode-free, Lean-Electrolyte Lithium-Sulfur Batteries Enabled by Tellurium-Stabilized Lithium Deposition

For realizing practically viable lithium-sulfur (Li-S) batteries, it is imperative to stabilize Li deposition and improve cyclability while reducing excess Li and electrolyte. We have discovered that introducing tellurium (Te) into the Li-S system as a cathode additive significantly improves the reversibility of Li plating and stripping by forming a tellurized and sulfide-rich solid-electrolyte interphase (SEI) layer on the Li surface. A remarkable improvement in cyclability is demonstrated in anode-free full cells with limited Li inventory and large-area Li-S pouch cells under lean electrolyte conditions. Tellurium reacts with polysulfides to generate soluble polytellurosulfides that migrate to the anode side and form stabilizing lithium thiotellurate and lithium telluride in situ as SEI components. A significant reduction in electrolyte decomposition on the Li surface is also engendered. This work demonstrates Te inclusion as a viable strategy for stabilizing Li deposition and establishes a robust evaluation framework for preserving electrochemical performance under limited Li and limited electrolyte conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Solar cell efficiency tables: Version 68

Consolidated tables showing an extensive listing of the highest independently confirmed efficiencies for photovoltaic solar cells and modules are presented. Guidelines for inclusion of results into these tables are outlined, and new entries since January 2026 are reviewed.

14 SOLAR ENERGY↗
DOE OSTI2025

Long carbon fibers boost performance of dry processed Li-ion battery electrodes

Dry processing (DP) is an advanced manufacturing technique for lithium-ion battery (LIB) electrodes. Unlike conventional wet-process-based manufacturing that involves dissolving polyvinylidene fluoride (PVDF) binder in n-methyl-2-pyrrolidone (NMP) solvent for slurry-casting, DP involves fibrillation of polymer binders. This method offers environmental and cost benefits by eliminating the need for expensive and environmentally hazardous organic solvents. However, DP-produced electrode films often lack mechanical stability due to the absence of a current collector substrate during electrode material layer fabrication. This reduced mechanical instability results in difficulty during fabricating of thin electrodes (≈5 mAh/cm 2 ). To address this issue, long (>8 mm) carbon fiber (CF) has been incorporated to reinforce the mechanical strength of the electrode films. In conclusion, the study demonstrates that the inclusion of long carbon fiber boosts the mechanical, electrical, thermal, and electrochemical performance of DP electrodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Deconvoluting the impact of current collector structure and electrolyte selection on Coulombic efficiency of lithium metal anodes

Lithium metal batteries are regarded as a promising avenue for significantly boosting the gravimetric energy density of batteries, particularly for electric vehicles. However, the instability of the lithium metal anode continues to hinder performance. While 3D structured current collectors for lithium metal anodes have been frequently proposed as a solution, few studies explore the impact of these structures when combined with various electrolytes and the inclusion of a lithium reservoir within the structure. This study pairs four commercially available copper current collectors with four different electrolytes to assess how these factors influence cycling performance with a 4 mAh/cm2 lithium reservoir. Coulombic efficiency (CE) measurements revealed no statistically significant difference in CE across different current collectors within the same electrolyte. However, significant variations were noted when the current collector remained intact, and the electrolyte was changed. Although polarization, electrochemical impedance, and lithium morphology varied between structures and electrolytes, no consistent patterns emerged to suggest superior performance by any specific current collector structure. Therefore, the choice of structure appears inconsequential when a lithium reservoir is present, and efforts should focus on selecting and designing the electrolyte.

White, Julia↗