Results for “Fuel Design” — Page 60

NASA NTRS1989

Integrated autopilot/autothrottle for the NASA TSRV B-737 aircraft: Design and verification by nonlinear simulation

An integrated autopilot/autothrottle was designed for flight test on the NASA TSRV B-737 aircraft. The system was designed using a total energy concept and is attended to achieve the following: (1) fuel efficiency by minimizing throttle activity; (2) low development and implementation costs by designing the control modes around a fixed inner loop design; and (3) maximum safety by preventing stall and engine overboost. The control law was designed initially using linear analysis; the system was developed using nonlinear simulations. All primary design requirements were satisfied.

Bruce, Kevin R.↗

NASA NTRS2017

Characterization, Operation and Analysis of Test Motors Containing Aluminized Hybrid Fuels

NASA Marshall Space Flight Center's Materials and Processes Department, with support from the Propulsion Systems Department, has renewed the development and maintenance of a hybrid test bed for exposing ablative thermal protection materials to an environment similar to that seen in solid rocket motors (SRM). The Solid Fuel Torch (SFT), operated during the Space Shuttle program, utilized gaseous oxygen for oxidizer and an aluminized hydroxyl-terminated polybutadiene (HTPB) fuel grain to expose a converging section of phenolic material to a 400 psi, 2-phase flow combustion environment. The configuration allows for up to a 2 foot long, 5 inch diameter fuel grain cartridge. Wanting to now test rubber insulation materials with a turn-back feature to mimic the geometry of an aft dome being impinged by alumina particles, the throat area has now been increased by several times to afford flow similarity. Combined with the desire to maintain a higher operating pressure, the oxidizer flow rate is being increased by a factor of 10. Out of these changes has arisen the need to characterize the fuel/oxidizer combination in a higher mass flux condition than has been previously tested at MSFC, and at which the literature has little to no reporting as well. Testing for fuel regression rate comprised a two-level, full factorial design available over Aluminum loading level, mass flow rate, pressure, and diameter. The data taken significantly surpasses the previous available data on regression rate of aluminized HTPB fuel burning with gaseous oxygen. It encompasses higher mass fluxes, and appears to generate more consistent data. The good test article and facility design and testing work of the Penn State HPCL combined with careful analysis of the data and good planning has made this possible. This should be able to assist with developing rate laws that are useful both for research planning and for developing flight system sizing relationships that can help optimize hybrid rocket concepts for trade studies. The successful approach of this DOE and test setup is applicable to other propellant combinations as well.

Kibbey, Timothy P.↗

NASA NTRS2017

Characterization, Operation and Analysis of Test Motors Containing Aluminized Hybrid Fuels

NASA Marshall Space Flight Center's Materials and Processes Department, with support from the Propulsion Systems Department, has renewed the development and maintenance of a hybrid test bed for exposing ablative thermal protection materials to an environment similar to that seen in solid rocket motors (SRM). The Solid Fuel Torch (SFT), operated during the Space Shuttle program, utilized gaseous oxygen for oxidizer and an aluminized hydroxyl-terminated polybutadiene (HTPB) fuel grain to expose a converging section of phenolic material to a 400 psi, 2-phase flow combustion environment. The configuration allows for up to a 2 foot long, 5 inch diameter fuel grain cartridge. Wanting to now test rubber insulation materials with a turn-back feature to mimic the geometry of an aft dome being impinged by alumina particles, the throat area has now been increased by several times to afford flow similarity. Combined with the desire to maintain a higher operating pressure, the oxidizer flow rate is being increased by a factor of 10. Out of these changes has arisen the need to characterize the fuel/oxidizer combination in a higher mass flux condition than has been previously tested at MSFC, and at which the literature has little to no reporting as well. Testing for fuel regression rate comprised a two-level, full factorial design available over Aluminum loading level, mass flow rate, pressure, and diameter. The data taken significantly surpasses the previous available data on regression rate of aluminized HTPB fuel burning with gaseous oxygen. It encompasses higher mass fluxes, and appears to generate more consistent data. The good test article and facility design and testing work of the Penn State HPCL combined with careful analysis of the data and good planning has made this possible. This should be able to assist with developing rate laws that are useful both for research planning and for developing flight system sizing relationships that can help optimize hybrid rocket concepts for trade studies. The successful approach of this DOE and test setup is applicable to other propellant combinations as well.

Kibbey, Timothy P.↗

NASA NTRS2016

Parametric Modeling Investigation of a Radially-Staged Low-Emission Aviation Combustor

Aviation gas-turbine combustion demands high efficiency, wide operability and minimal trace gas emissions. Performance critical design parameters include injector geometry, combustor layout, fuel-air mixing and engine cycle conditions. The present investigation explores these factors and their impact on a radially staged low-emission aviation combustor sized for a next-generation 24,000-lbf-thrust engine. By coupling multi-fidelity computational tools, a design exploration was performed using a parameterized annular combustor sector at projected 100% takeoff power conditions. Design objectives included nitrogen oxide emission indices and overall combustor pressure loss. From the design space, an optimal configuration was selected and simulated at 7.1, 30 and 85% part-power operation, corresponding to landing-takeoff cycle idle, approach and climb segments. All results were obtained by solution of the steady-state Reynolds-averaged Navier-Stokes equations. Species concentrations were solved directly using a reduced 19-step reaction mechanism for Jet-A. Turbulence closure was obtained using a nonlinear K-epsilon model. This research demonstrates revolutionary combustor design exploration enabled by multi-fidelity physics-based simulation.

design analysis↗

NASA NTRSDate not supplied

Current Test Capabilities of NASA Langley’s Arc-Heated Scramjet Test Facility

The Arc-Heated Scramjet Test Facility at NASA Langley Research Center has demonstrated itself repeatedly as a key contributor to fundamental hypersonic research and scramjet engine technology development in the Mach 4.7 to 8 range. Since its inception in the 1970’s, the facility has hosted numerous scramjet engine configurations that explored the performance and operability of airframe-integrated hydrogen-fueled scramjet flow path concepts, successfully maturing both analysis tools and design technique and methodology for hypersonic propulsion. Contributions to major programs include extensive tests of the hydrogen-fueled NASP and Hyper-X scramjet engines, and the hydrocarbon-fueled HIFiRE Flight 2 scramjet flow path, in addition to fundamental in-house research. The facility capabilities have expanded to include direct-connect flow path support, gaseous hydrocarbon fuels, dynamic trajectory simulation and extension of flight simulation down to Mach 2.2. The low-Mach upgrades include increased air flow rate and controls capability and two new low-Mach nozzles (Mach 2.2 and 3.5). The facility recently completed verification of the new operational range through successful envelope expansion tests with the Mach 2.2 nozzle. With these new modifications, the operating envelope for the facility is now Mach 2.2 – 8.0(+), with a demonstrated dynamic pressure simulation of 2000 psf at the low end, and margin available for even more. Lastly, a continuous run time of over 5 minutes has been demonstrated, indicating that run time is limited only by test hardware or back-pressure requirements. This paper will provide a detailed description of these previously unreported upgrades and expanded simulation capabilities.

Hypersonic↗

NASA NTRS1989

A hypersonic executive transport

Four teams of seven students each developed conceptual designs for a hypersonic executive transport. The specifications called for a 10-passenger jet that had a range of 6000 nm while cruising at a Mach number between M = 4 and M = 6 and was capable of operating from 10,000-ft runways. The configurations produced by the student design teams varied significantly in both planform and propulsion, but all met the mission requirements. A methane-fueled, variable-cycle turbofan-ramjet powered, double-delta transport was the most conventional design; a second aircraft having variable sweep canards utilized hydrogen-fueled turbofan-ramjet engines and laminar flow control on its delta wing. Two configurations were derived from waverider concepts, analytically shaped flying wings that exploit an M = 6 shock wave for efficient lift-to-drag ratios. One of the waveriders uses a liquid, noncryogenic fuel - methylcyclohexane - to power separate turbofan and ramjet engines. The second waverider initially operates its turbofan-ramjet engine with liquid JP-X for take-off and flight to M = 3, then switches to liquid hydrogen for the ramjet high Mach number cycle. The design studies include the effects of aerodynamic heating, environmental concerns, and operating and production costs of each hypersonic transport.

Debonis, J.↗

NASA NTRS2017

Robust Acoustic Objective Functions and Sensitivities in Adjoint-Based Design Optimizations

The multidisciplinary design of aircraft typically includes considerations of performance, weight, fuel burn, and noise, among other factors. An objective function is applied to each of these considerations in order to weight the influence of trade-offs between different designs. Higher-order optimization exercises have utilized an adjoint approach to reach an optimal set of objective functions, such as maximum lift and reduced drag. Taking advantage of the adjoint approach significantly reduces the computational time required to find an optimal configuration. Including acoustics in the set of objective functions during an adjoint-based design optimization requires the sensitivity of the acoustic objective function. This document will present an approach for defining the sensitivity of several acoustic metrics and operations that can fill the role of the acoustic objective function. This includes time-integrated metrics such as effective perceived noise level (EPNL) and frequency-integrated metrics such as overall sound pressure level (OASPL). A demonstration case, validation, and details on the implementation in the second generation Aircraft NOise Prediction Program (ANOPP2) are also shown.

Lopes, Leonard V.↗

NASA NTRS1978

Liquid hydrogen tankage design

For this, the tankage experienced only minor thermal loadings and flight loads, hence, the predominate loading was the tank pressurization. Since the tanks were basically tension designed, the fatigue and damage tolerance criteria played the most important part in the overall design of the tank. Sensitivity factors were generated for the reference LH2-fueled airplane to provide a basis for evaluation of the effects of changes from the baseline design. For example, the various candidate insulation systems and tank structural concepts offer tradeoffs of the tankage offset distance (distance between exterior surface to tank) and weight. As the offset varies, the aircraft fuselage length must change to provide the required fuel volume within the fixed fuselage cross-section and hence the sensitivity on the aircraft DOC could be assessed.

Davis, G. W.↗

NASA NTRS1993

Material requirements for the High Speed Civil Transport

Under NASA-sponsored High Speed Research (HSR) programs, the materials and processing requirements have been identified for overcoming the environmental and economic barriers of the next generation High Speed Civil Transport (HSCT) propulsion system. The long (2 to 5 hours) supersonic cruise portion of the HSCT cycle will place additional durability requirements on all hot section engine components. Low emissions combustor designs will require high temperature ceramic matrix composite liners to meet an emission goal of less than 5g NO(x) per Kg fuel burned. Large axisymmetric and two-dimensional exhaust nozzle designs are now under development to meet or exceed FAR 36 Stage III noise requirements, and will require lightweight, high temperature metallic, intermetallic, and ceramic matrix composites to reduce nozzle weight and meet structural and acoustic component performance goals. This paper describes and discusses the turbomachinery, combustor, and exhaust nozzle requirements of the High Speed Civil Transport propulsion system.

Stephens, Joseph R.↗

NASA NTRS1974

Space tug thermal control

It was determined that space tug will require the capability to perform its mission within a broad range of thermal environments with currently planned mission durations of up to seven days, so an investigation was conducted to define a thermal design for the forward and intertank compartments and fuel cell heat rejection system that satisfies tug requirements for low inclination geosynchronous deploy and retrieve missions. Passive concepts were demonstrated analytically for both the forward and intertank compartments, and a worst case external heating environment was determined for use during the study. The thermal control system specifications and designs which resulted from the research are shown.

Source record↗

NASA NTRS1976

Study of cost/benefit tradeoffs for reducing the energy consumption of the commercial air transportation system

Economic studies were conducted for three general fuel conserving options: (1) improving fuel consumption characteristics of existing aircraft via retrofit modifications; (2) introducing fuel efficient derivations of existing production aircraft and/or introducing fuel efficient, current state-of-the-art new aircraft; and (3) introducing an advanced state-of-the-art turboprop airplane. These studies were designed to produce an optimum airline fleet mix for the years 1980, 1985 and 1990. The fleet selected accommodated a normal growth market by introducing somewhat larger aircraft while solving for maximum departure frequencies and a minimum load factor corresponding to a 15% investment hurdle rate. Fuel burnt per available-seat-mile flown would drop 22% from 1980 to 1990 due to the use of more fuel efficient aircraft designs, larger average aircraft size, and increased seating density. An inflight survey was taken to determine air traveler attitudes towards a new generation of advanced turboprops.

Coykendall, R. E.↗

NASA NTRS1956

Turbojet-engine Starting and Acceleration

From considerations of safety and reliability in performance of gas-turbine aircraft, it is clear that engine starting and acceleration are of utmost importance. For this reason extensive efforts have been devoted to the investigation of the factors involved in the starting and acceleration of engines. In chapter III it is shown that certain basic combustion requirements must be met before ignition can occur; consequently, the design and operation of an engine must be tailored to provide these basic requirements in the combustion zone of the engine, particularly in the vicinity of the ignition source. It is pointed out in chapter III that ignition by electrical discharges is aided by high pressure, high temperature, low gas velocity and turbulence, gaseous fuel-air mixture, proper mixture strength, and-an optimum spark. duration. The simultaneous achievement of all these requirements in an actual turbojet-engine combustor is obviously impossible, yet any attempt to satisfy as many requirements as possible will result in lower ignition energies, lower-weight ignition systems, and greater reliability. These factors together with size and cost considerations determine the acceptability of the final ignition system. It is further shown in chapter III that the problem of wall quenching affects engine starting. For example, the dimensions of the volume to be burned must be larger than the quenching distance at the lowest pressure and the most adverse fuel-air ratio encountered. This fact affects the design of cross-fire tubes between adjacent combustion chambers in a tubular-combustor turbojet engine. Only two chambers in these engines contain spark plugs; therefore, the flame must propagate through small connecting tubes between the chambers. The quenching studies indicate that if the cross-fire tubes are too narrow the flame will not propagate from one chamber to another. In order to better understand the role of the basic factors in actual engine operation, many investigations have been conducted in single combustors from gas-turbine engines and in full-scale engines in altitude tanks and in flight. The purpose of the present chapter is to discuss the results of such studies and, where possible, to interpret these results qualitatively in terms of the basic requirements reported in chapter III. The discussion parallels the three phases of turbojet engine starting: (1) Ignition of the fuel-air mixture (2) Propagation of flame throughout the combustion zone (3) Acceleration of the engine to operating speed.

Mc Cafferty, R. J.↗

NASA NTRS1978

Preliminary design characteristics of a subsonic business jet concept employing laminar flow control

Aircraft configurations were developed with laminar flow control (LFC) and without LFC. The LFC configuration had approximately eleven percent less parasite drag and a seven percent increase in the maximum lift-to drag ratio. Although these aerodynamic advantages were partially offset by the additional weight of the LFC system, the LFC aircraft burned from six to eight percent less fuel for comparable missions. For the trans-atlantic design mission with the gross weight fixed, the LFC configuration would carry a greater payload for ten percent fuel per passenger mile.

Turriziani, R. V.↗

NASA NTRS1994

Fundamental phenomena on fuel decomposition and boundary layer combustion processes with applications to hybrid rocket motors

An experimental study on the fundamental processes involved in fuel decomposition and boundary layer combustion in hybrid rocket motors is being conducted at the High Pressure Combustion Laboratory of the Pennsylvania State University. This research should provide an engineering technology base for development of large scale hybrid rocket motors as well as a fundamental understanding of the complex processes involved in hybrid propulsion. A high pressure slab motor has been designed for conducting experimental investigations. Oxidizer (LOX or GOX) is injected through the head-end over a solid fuel (HTPB) surface. Experiments using fuels supplied by NASA designated industrial companies will also be conducted. The study focuses on the following areas: measurement and observation of solid fuel burning with LOX or GOX, correlation of solid fuel regression rate with operating conditions, measurement of flame temperature and radical species concentrations, determination of the solid fuel subsurface temperature profile, and utilization of experimental data for validation of a companion theoretical study also being conducted at PSU.

Kuo, Kenneth K.↗

NASA NTRS1987

Analysis of an advanced technology subsonic turbofan incorporating revolutionary materials

Successful implementation of revolutionary composite materials in an advanced turbofan offers the possibility of further improvements in engine performance and thrust-to-weight ratio relative to current metallic materials. The present analysis determines the approximate engine cycle and configuration for an early 21st century subsonic turbofan incorporating all composite materials. The advanced engine is evaluated relative to a current technology baseline engine in terms of its potential fuel savings for an intercontinental quadjet having a design range of 5500 nmi and a payload of 500 passengers. The resultant near optimum, uncooled, two-spool, advanced engine has an overall pressure ratio of 87, a bypass ratio of 18, a geared fan, and a turbine rotor inlet temperature of 3085 R. Improvements result in a 33-percent fuel saving for the specified misssion. Various advanced composite materials are used throughout the engine. For example, advanced polymer composite materials are used for the fan and the low pressure compressor (LPC).

Knip, Gerald, Jr.↗

NASA NTRS1984

Measurements in liquid fuel sprays

Techniques for studying the events directly preceding combustion in the liquid fuel sprays are being used to provide information as a function of space and time on droplet size, shape, number density, position, angle of flight and velocity. Spray chambers were designed and constructed for: (1) air-assist liquid fuel research sprays; (2) high pressure and temperature chamber for pulsed diesel fuel sprays; and (3) coal-water slurry sprays. Recent results utilizing photography, cinematography, and calibration of the Malvern particle sizer are reported. Systems for simultaneous measurement of velocity and particle size distributions using laser Doppler anemometry interferometry and the application of holography in liquid fuel sprays are being calibrated.

Chigier, N.↗

NASA NTRS1989

Fuel properties effect on the performance of a small high temperature rise combustor

The performance of an advanced small high temperature rise combustor was experimentally determined at NASA-Lewis. The combustor was designed to meet the requirements of advanced high temperature, high pressure ratio turboshaft engines. The combustor featured an advanced fuel injector and an advanced segmented liner design. The full size combustor was evaluated at power conditions ranging from idle to maximum power. The effect of broad fuel properties was studied by evaluating the combustor with three different fuels. The fuels used were JP-5, a blend of Diesel Fuel Marine/Home Heating Oil, and a blend of Suntec C/Home Heating Oil. The fuel properties effect on the performance of the combustion in terms of pattern factor, liner temperatures, and exhaust emissions are documented.

Acosta, Waldo A.↗

NASA NTRS1989

Fuel properties effect on the performance of a small high temperature rise combustor

The performance of an advanced small high temperature rise combustor was experimentally determined at NASA-Lewis. The combustor was designed to meet the requirements of advanced high temperature, high pressure ratio turboshaft engines. The combustor featured an advanced fuel injector and an advanced segmented liner design. The full size combustor was evaluated at power conditions ranging from idle to maximum power. The effect of broad fuel properties was studied by evaluating the combustor with three different fuels. The fuels used were JP-5, a blend of Diesel Fuel Marine/Home Heating Oil, and a blend of Suntec C/Home Heating Oil. The fuel properties effect on the performance of the combustion in terms of pattern factor, liner temperatures, and exhaust emissions are documented.

Acosta, Waldo A.↗