Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAT PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Computational model of miniature pulsating heat pipes

The modeling work described herein represents Sandia National Laboratories (SNL) portion of a collaborative three-year project with Northrop Grumman Electronic Systems (NGES) and the University of Missouri to develop an advanced, thermal ground-plane (TGP), which is a device, of planar configuration, that delivers heat from a source to an ambient environment with high efficiency. Work at all three institutions was funded by DARPA/MTO; Sandia was funded under DARPA/MTO project number 015070924. This is the final report on this project for SNL. This report presents a numerical model of a pulsating heat pipe, a device employing a two phase (liquid and its vapor) working fluid confined in a closed loop channel etched/milled into a serpentine configuration in a solid metal plate. The device delivers heat from an evaporator (hot zone) to a condenser (cold zone). This new model includes key physical processes important to the operation of flat plate pulsating heat pipes (e.g. dynamic bubble nucleation, evaporation and condensation), together with conjugate heat transfer with the solid portion of the device. The model qualitatively and quantitatively predicts performance characteristics and metrics, which was demonstrated by favorable comparisons with experimental results on similar configurations. Application of the model also corroborated many previous performance observations with respect to key parameters such as heat load, fill ratio and orientation.

97 MATHEMATICS AND COMPUTING↗

Vapor chambers for an atmospheric cloud physics laboratory

The methanol/stainless steel vapor chambers (flat-plate heat pipes) discussed in this paper were developed for use in spaceborne atmospheric cloud chambers. This application imposed stringent thermal and mechanical requirements on the design. Flatness, low thermal mass, vibration, and structural integrity requirements were achieved in addition to precision temperature uniformity and thermal transport. Heat transfer coefficients on the order of 0.34 to 0.40 W/sq cm -C were measured. The vapor chambers are capable of transporting 170 W-cm per cm of width in either the axial or side-to-side direction.

Fleischman, G. L.↗

Turbulent boundary layer heat transfer experiments: Convex curvature effects, including introduction and recovery

Heat transfer rates were measured through turbulent and transitional boundary layers on an isothermal, convexly curved wall and downstream flat plate. The effect of convex curvature on the fully turbulent boundary layer was a reduction of the local Stanton numbers 20-50% below those predicted for a flat wall under the same circumstances. The recovery of the heat transfer rates on the downstream flat wall was extremely slow. After 60 cm of recovery length, the Stanton number was still typically 15-20% below the flat wall predicted value. Various effects important in the modeling of curved flows were studied separately. These are: (1) the effect of initial boundary layer thickness; (2) the effect of freestream velocity; (3) the effect of freestream acceleration; (4) the effect of unheated starting length; and (5) the effect of the maturity of the boundary layer. Regardless of the initial state, curvature eventually forced the boundary layer into an asymptotic curved condition. The slope, minus one, is believed to be significant.

Simon, T. W.↗

Large Eddy Simulation of Heat Transfer Over In-Line Flat-Tube Array in Laminar and Turbulent Flows

This study presents a transient three-dimensional numerical study on fluid flow and heat transfer of flat-tube array using large eddy simulation (LES) covering both laminar and turbulent flow regimes. The simulations were performed in a rectangular region containing only one tube with periodic conditions specified on all boundaries. A staggered flat-plate array was first studied, and an existing solution was used for validation purpose. The numerical models were then applied to an in-line array composed of flat tubes with an aspect ratio of 0.25 and fixed tube spacings. By varying the in-flow velocity, the tube array was studied over a wide range of Reynolds number (600–12000). Temperature, velocity, and turbulent kinetic energy distributions as well as the interactions between them are presented and analyzed. Furthermore, the local heat transfer rate was analyzed along the various parts of the tube (leading edge, flat-top and wake or trailing-edge regions). Heat transfer correlation for each region of the tube and the entire tube array is proposed..

Taghizadeh, Salar↗

Turbulent boundary layer heat transfer experiments: Convex curvature effects including introduction and recovery

Measurements were made of the heat transfer rate through turbulent and transitional boundary layers on an isothermal, convexly curved wall and downstream flat plate. The effect of convex curvature on the fully turbulent boundary layer was a reduction of the local Stanton numbers 20% to 50% below those predicted for a flat wall under the same circumstances. The recovery of the heat transfer rates on the downstream flat wall was extremely slow. After 60 cm of recovery length, the Stanton number was still typically 15% to 20% below the flat wall predicted value. Various effects important in the modeling of curved flows were studied separately. These are: the effect of initial boundary layer thickness, the effect of freestream velocity, the effect of freestream acceleration, the effect of unheated starting length, and the effect of the maturity of the boundary layer. An existing curvature prediction model was tested against this broad heat transfer data base to determine where it could appropriately be used for heat transfer predictions.

Simon, T. W.↗

An Experimental Study of Turbulent Skin Friction Reduction in Supersonic Flow Using a Microblowing Technique

A new turbulent skin friction reduction technology, called the microblowing technique has been tested in supersonic flow (Mach number of 1.9) on specially designed porous plates with microholes. The skin friction was measured directly by a force balance and the boundary layer development was measured by a total pressure rake at the tailing edge of a test plate. The free stream Reynolds number was 1.0(10 exp 6) per meter. The turbulent skin friction coefficient ratios (C(sub f)/C(sub f0)) of seven porous plates are given in this report. Test results showed that the microblowing technique could reduce the turbulent skin friction in supersonic flow (up to 90 percent below a solid flat plate value, which was even greater than in subsonic flow).

Hwang, Danny P.↗

Experimental Study of Saddle Point of Attachment in Laminar Juncture Flow

An experimental study of laminar horseshoe vortex flows upstream of a cylinder/flat plate juncture has been conducted to verify the existence of saddle-point-of-attachment topologies. In the classical depiction of this flowfield, a saddle point of separation exists on the flat plate upstream of the cylinder, and the boundary layer separates from the surface. Recent computations have indicated that the topology may actually involve a saddle point of attachment on the surface and additional singular points in the flow. Laser light sheet flow visualizations have been performed on the symmetry plane and crossflow planes to identify the saddle-point-of-attachment flowfields. The visualizations reveal that saddle-point-of-attachment topologies occur over a range of Reynolds numbers in both single and multiple vortex regimes. An analysis of the flow topologies is presented that describes the existence and evolution of the singular points in the flowfield.

Coon, Michael D.↗

The Additional-Mass Effect of Plates as Determined by Experiments

The apparent increase in the inertia properties of a body moving in a fluid medium has been called the additional-mass effect. This report presents a resume of test procedures and results of experimental determinations of the additional-mass effect of flat plates. In addition to data obtained from various foreign sources and from a NACA investigation in 1933, the results of tests recently conducted by the National Advisory Committee for Aeronautics are included.

Gracey, William↗

Pressure distributions induced by elevon deflections on swept wings and adjacent end-plate surfaces at Mach 6

Surface pressure distributions are presented for regions where three-dimensional separated flow effects are prominent on swept-wing-elevon-end-plate models of 0 degree, 50 degree, and 70 degree sweepback, and with 0 degree, 10 degree, 20 degree, and 30 degree elevon deflections. Surface-oil-flow photographs and pressure distributions on the flat-plate wing, elevon, and end-plate surfaces are presented for numerous geometric variations, including various spacings between the elevon and the end plate, with and without a tip fin. The data, for a free-stream Mach number of 6 and a wing-root-chord Reynolds number of 20 x 10 to the sixth power, reveal considerably larger regions of elevon induced loads on the adjacent end-plate surface than would be anticipated by using inviscid flow analyses.

Kaufman, L. G., II↗

Design and Manufacture of Elastically Tailored Tow Placed Plates

Elastic stiffness tailoring of laminated composite panels by allowing the fibers to curve within the plane of the laminate is a relatively novel design concept that has been demonstrated to be both beneficial and practical. In particular, for structures with highly non-uniform stress states, such as the case of a flat panel with a central hole subjected to in-plane loading, the concept is likely to provide substantial improvements in load carrying capability. The objective of the present study is to determine the effectiveness of stiffness tailoring through the use of curvilinear fibers to reduce stress concentrations around the hole and improve the load carrying capability of panels with holes. In this study software was created that translates standard finite element models with traditional laminate definitions into ones that possess stacking sequences with curvilinear fiber paths that are directly manufacturable using an advanced tow placement machine. Preliminary designs for the manufacturing and testing phase were determined through rudimentary design studies for flat plates without holes under axial compression. These candidate designs were then analyzed using finite element models that accurately reflect the test conditions and geometries in order to select final designs for testing. A total of six large panels, measuring three feet by six feet, each of which are used to produce four specimens with or without holes, were fabricated and delivered to NASA for machining and testing.

Tatting, Brain F.↗

Comparison of Mixing Characteristics for Several Fuel Injectors on an Open Plate and in a Ducted Flowpath Configuration at Hypervelocity Flow Conditions

In order to reduce the cost and complexity associated with fuel injection and mixing experiments for high-speed flows, and to further enable optical access to the test section for nonintrusive diagnostics, the Enhanced Injection and Mixing Project (EIMP) utilizes an open flat plate configuration to characterize inert mixing properties of various fuel injectors for hypervelocity applications. The experiments also utilize reduced total temperature conditions to alleviate the need for hardware cooling. The use of "cold" flows and non-reacting mixtures for mixing experiments is not new, and has been extensively utilized as a screening technique for scramjet fuel injectors. The impact of reduced facility-air total temperature, and the use of inert fuel simulants, such as helium, on the mixing character of the flow has been assessed in previous numerical studies by the authors. Mixing performance was characterized for three different injectors: a strut, a ramp, and a flushwall. The present study focuses on the impact of using an open plate to approximate mixing in the duct. Toward this end, Reynolds-averaged simulations (RAS) were performed for the three fuel injectors in an open plate configuration and in a duct. The mixing parameters of interest, such as mixing efficiency and total pressure recovery, are then computed and compared for the two configurations. In addition to mixing efficiency and total pressure recovery, the combustion efficiency and thrust potential are also computed for the reacting simulations.

Drozda, Tomasz G.↗

Evacuation-induced pressure differentials in multilayer insulation systems

The pressure differentials induced across three types of multilayer insulation systems during evacuation have been measured and compared with values predicted using an idealized parallel plate geometric model. The systems tested were double-aluminized Mylar with a Tissuglas or silk net spacer and crinkled single-aluminized Mylar. Test samples were circular. The influence of purge gas type, layer density, sample diameter, and temperature was systematically investigated. The experimental approach was to measure the absolute pressure history and corresponding pressure differential induced across the insulation during evacuation. The measured pressure differentials were nondimensionalized and compared with those predicted by the parallel plate model as a function of Knudsen number. It was concluded that the parallel plate model is adequate for making engineering analyses. The influence of all parameters, except layer density, is well represented by the model. Representation of the influence of layer density is less satisfactory, but can be improved by modification of the flat plate model to allow for the more obvious practical nonidealities, such as crinkling, or the presence of a net spacer.

Glassford, A. P. M.↗

The performance of smooth-wall drag reducing outer-layer devices in rough-wall boundary layers

The boundary layer drag on a 0.28 m x 0.91 m flat-plate was measured to evaluate the performance of smooth-wall drag reducing outer-layer devices in rough-wall boundary layers up to a chord Reynolds number, Re(c) of 17,000. The devices were a pair of thin flat ribbons placed in tandem. The wall conditions examined were smooth, transverse-groove roughnesses having cavity width/depth ratios of 0.7 (d-type) and 3 (k-type), and sandpaper roughness (k-type) of grit sizes 180, 50 and 36. The area-averaged wall-drag was reduced compared to the respective normal levels for all wall conditions. All k-type rough walls exhibited a comparable level of drag reduction (about 7 percent) which was lower than that in the smooth-wall. The d-type rough-wall exhibited a transitional behavior in that the drag reduction dropped from the smooth-wall level to that of the k-type roughnesses with increase in the flow speed. In further experiments on a 6 meter long sandpaper roughened wall and with a pair of symmetric airfoil devices in tandem at an Re(c) of 77,500, it was possible to recover the device drag penalty fully, but no net drag reduction was achieved. The apparent loss of performance of the devices in a rough-wall is explained in terms of their inability to alter the pressure component of the drag in a significant way.

Bandyopadhyay, P. R.↗

Scaling Analysis of Vortex Shedding Frequency between In line Plates

The Global Threat Reduction initiative (GTRI) was established by the National Nuclear Security Administration (NNSA) in 2004. One of the highlights of the program is to convert research and test reactors at home and abroad from Highly Enriched Uranium (HEU) to Low Enriched Uranium (LEU) fuels. By switching directly from HEU to LEU, an LEU reactor produces fewer neutrons than an HEU reactor and in some cases; a direct switch from HEU to LEU results in the reactor being unable to achieve criticality. Under certain circumstances, criticality is achieved and the original neutron fluxes are restored with LEU fuel by adding more fuel elements to the core. Not all reactors, exemplified by the Advanced Test Reactor (ATR) at the Idaho National Lab (INL), have the luxury of simply adding more fuel to the core. In such cases, entirely new designs must be created and tested. The ATR utilizes plate type fuel. During the design and testing of the ATR fuel, vortex shedding was identified as potential source for experiment and fuel failure. For fuel conversion, elements must be tested in pile prior to the qualification of the new fuel design. For some test elements, the primary test plate is followed by a secondary handling plate. It is known that objects downstream influence the vortex shedding. While vortex shedding is an important and well-studied phenomenon, not only in the context of nuclear engineering, but in fields as diverse as aeronautical engineering and biology, there is a significant gap in the understanding of vortex shedding in regards to two bluff bodies in line direct line with one another. The study provides a scaling analysis of the frequency of vortex shedding for plates in line. The scaling analysis is then compared to numerical simulation of two in line plates. The study provided a scaling analysis and suggested parameter for determining the expected trends in the Strouhal number for a plate with some object downstream. The analysis made the consideration of differing length scales as the cause for a reduction in vortex shedding frequency as well as looked at the potential impact of boundary layer growth on vortex shedding for a flat plate. The comparison between the expected scaling and numerical data was less than ideal, but there are several potential causes. One of the biggest issues with the comparison is the uncertainty associated with the defect velocity. The frequency was well established in several cases, but the velocity was not always well established resulting in a larger uncertainty. In the cases where the velocity was near zero (i.e. b/d = 0.5), the uncertainty dominated since the corrected Strouhal number is divided by the defect velocity. The Reynolds numbers were not incredibly large, ranging from 350-1600. The low Reynolds numbers potentially undermine the principle assumption made in the scaling analysis, i.e. Reynolds number is negligibly small. Additionally, the exact definition of the 'reduced velocity' was never explicitly defined, merely inferred from the assumption that the x length scale and y length scale were in fact different. Another potential problem is the defect velocities in the lower Reynolds number cases were not much smaller than the free stream velocity. Further work needs to be done at higher Reynolds numbers and with more data points to ensure the assumptions made are valid as well as confirm the accuracy of the scaled relationship. (authors)

42 ENGINEERING↗

A correlation method to predict the surface pressure distribution of an infinite plate or a body of revolution from which a jet is issuing

A correlation method to predict pressures induced on an infinite plate by a jet exhausting normal to the plate into a subsonic free stream was extended to jets exhausting at angles to the plate and to jets exhausting normal to the surface of a body revolution. The complete method consisted of an analytical method which models the blockage and entrainment properties of the jet and an empirical correlation which accounts for viscous effects. For the flat plate case, the method was applicable to jet velocity ratios up to ten, jet inclination angles up to 45 deg from the normal, and radial distances up to five diameters from the jet. For the body of revolution case, the method was applicable to a body at zero degrees angle of attack, jet velocity ratios 1.96 and 3.43, circumferential angles around the body up to 25 deg from the jet, axial distances up to seven diameters from the jet, and jet-to-body diameter ratios less than 0.1.

Perkins, S. C., Jr.↗

First Annual Report on Pulsed Thermal Tomography Nondestructive Evaluation of Additively Manufactured Reactor Materials and Components: Pulsed Thermal Tomography Nondestructive Examination of Additively Manufactured Reactor Materials and Components

Additive manufacturing (AM, or 3D printing) for commercial nuclear energy applications is an emerging method for cost-efficient manufacturing aimed at replacing aging nuclear reactor parts and reducing costs for new construction. Because of the geometry of metallic structures of interest for nuclear applications, which consist of planar primitives with no symmetry of revolution, limited options are available for nondestructive evaluation (NDE), either during or post manufacturing. Known material flaws in AM include low-density regions consisting of non-sintered powder, which have to be detected to ensure the safety of long-term performance nuclear reactor components. As a solution to NDE of AM, we are developing pulsed thermal tomography (PTT) models and depth inversion algorithms for 3D imaging. PTT has many advantages because the method is non-contact and allows for in-service, NDE of AM nuclear reactor parts. By analyzing transients of surface temperature response due to internal thermal resistances, one can obtain 3D reconstructions of material effusivity using a unique inversion algorithm developed at Argonne. This report provides results of preliminary performance evaluation of PTT capability in detection of flaws in metallic structures, as well imaging complex geometry AM structures. Performance of PTT was investigated through modeling and experiments, Computer models of PTT were developed using COMSOL Heat Transfer module. Defects were modeled as cylindrical flat bottom holes (FBH), which is a common model of calibrated material flaws in thermal tomography experiments. Materials considered in this study include stainless steel 316 (SS316), stainless steel 304 (SS304), and Inconel 718. Theoretical analyses were conducted to validate inversion of simulated PTT data with COMSOL for a plate. Subsequently, 3D reconstructions were performed on COMSOL simulations for FBH, revealing a decrease in spatial resolution over depth due to thermal diffusion. The results of this study show that the performance of the inversion algorithm for detecting smaller defects depends strongly on the depth of the defect as well as the incident heat flux. The size of detectable defect was estimated by fitting a Gaussian function to surface temperature profile. The criteria for detectability was taken as 20mK noise equivalent temperature difference (NETD), which is currently the sensitivity limit of high-performance infrared cameras. It was determined through computer simulations that the smallest detectable FBH in SS316 has a 50µm diameter and is located 0.5mm below the plate surface. Preliminary experimental studies were performed to evaluate PTT performance in detecting calibrated flaws using metallic specimens with AM defects simulated as drilled-in FBH’s. High strength Stainless Steel 316 and Inconel 718 alloys were considered, as well as lower grade Stainless Steel 304, Nickel 200, and Hastelloy C276. Specimens investigated in this report consisted of approximately 1/4in-thick plates made out of these alloys using conventional manufacturing methods. The diameters of FBH’s varied from 1mm to 8mm, and their depths below the plate flat surface varied between 1mm and 6mm. The size of the smallest FBH was limited to 1mm because conventional mechanical drills were used for creating the holes. PTT imaging results have shown that 1mm-diameter FBH located 1mm and 2mm below the surface were detectable. Larger size FBH were detectable at greater depth. For example, 6mm-diameter FBH could be detected at 8mm depth. Image contrast varied slightly between the specimens, with the best reconstructions obtained in SS316 and C276 plates. Finally, PTT capability in imaging several AM structures fabricated from Inconel 718 (IN718) powder feedstock was investigated. The AM structures have complex geometry, but do not have calibrated internal defects. The objective is to determine PTT settings, such as the total integration time, for imaging of representative AM structures. A new FLIR X8500sc IR camera with higher spatial resolution (1280x1024 at 181Hz frame rate) was integrated into the PTT laboratory setup. Software tools were developed to ensure compatibility of new camera files with legacy effusivity reconstruction codes. The new camera was used to obtain 3-D reconstructions of AM IN718 nozzle plate and a particle filter plate. It was shown that PTT can scan through 2/3in-thick Inconel 718 plates in approximately 15s. Several modes of 3-D data visualization were explored, including using ImageJ and MATLAB software packages. The results demonstrate the capability of PTT in 3-D imaging of complex geometry AM structures. Intermediate results demonstrated in this report will be developed further to investigate detection of flaws in AM specimens.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Analyzing photovoltaic module mechanics using composite plate theories and finite element solutions

Deflection and stress calculated from an experimentally validated, high-fidelity finite element model (FEM) of a photovoltaic module experiencing mechanical load was compared to results from a simplified FEM treating the module laminate as a homogenized composite using a rule of mixtures approach, and further compared to analytical calculations treating the module as a Kirchoff-Love flat plate. The goal of this study was to determine the error incurred by analyzing module mechanics with varying levels of simplification, since resolving the aspect ratios of a module is computationally expensive. Homogenized FEMs were found to underpredict peak deflection under a 1.0 kPa load by between 13 and 19% for lower and upper bound application of the rule of mixtures. However, module shape was captured, implying that a useful replication of a resolved model could be achieved with a reduced, calibrated material stiffness. Homogenized stress results captured glass layer tensile stress components to within 46 to 52% at a sample location of interest, though agreement was poor through the remainder of the laminate due to the lack of material resolution. For plate theory, deflection was overpredicted by 45 to 67% for upper and lower bound homogenizations, and frame-adjacent module shapes were not adequately replicated. Stress results mirrored FEM trends but magnitudes were not well correlated to resolved model values. These results support the use of homogenized laminate models for module shape derivation, though resolved models remain necessary for stress analyses. The accuracy of plate theory was found to be inadequate for most applications.

14 SOLAR ENERGY↗

Transition boiling heat transfer and the film transition regime

The Berenson (1960) flat-plate transition-boiling experiment has been recreated with a reduced thermal resistance in the heater, and an improved access to those portions of the transition boiling regime that have a steep negative slope. Tests have been made in Freon-113, acetone, benzene, and n-pentane boiling on horizontal flat copper heaters that have been mirror-polished, 'roughened', or teflon-coated. The resulting data reproduce and clarify certain features observed by Berenson: the modest surface finish dependence of boiling burnout, and the influence of surface chemistry on both the minimum heat flux and the mode of transition boiling, for example. A rational scheme of correlation yields a prediction of the heat flux in what Witte and Lienhard (1982) previously identified as the 'film-transition boiling' region. It is also shown how to calculate the heat flux at the boundary between the pure-film, and the film-transition, boiling regimes, as a function of the advancing contact angle.

Ramilison, J. M.↗