Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Effects of chromium and aluminum on mechanical and oxidation properties of iron-nickel-base superalloys based on CG-27

The effects of chromium and aluminum on the mechanical and oxidation properties of a series of gamma-prime-strengthened alloys based on CG-27 were studied. Gamma-prime dispersion and solid-solution strengthening were the principal modes of alloy strengthening. The oxidation attack parameter K sub a decreased with increasing Cr and Al contents for each alloy group based on Al content. As a group, alloys with 3 wt % Al had the lowest attack parameters. Therefore, 3 wt % is the optimum level of Al for parabolic oxidation behavior. Spalling, due to diffusion-induced grain growth, was controlled by the overall Cr and Al levels. The alloy with 4 wt % Cr and 3 wt % Al had stress-rupture properties superior to those of the base alloy, CG-27, and maintained parabolic oxidation behavior while the Cr content was reduced by two-thirds of its value in cast CG-27.

Schuon, S. R.↗
NASA NTRS1990

Effect of neutron irradiation on the thermoelectric properties of SiGe alloys

Zone-leveled and hot-pressed n- and p-type Si80Ge20 alloys were irradiated with neutrons to a fluence of 4 x 1018 n/sq cm and to a fluence of 5.4 x 1019 n/sq cm at a temperature of approximately 200-300 C. The effect of neutron irradiation on the thermoelectric properties of these alloys was evaluated. The carrier concentration and mobility (and hence the resistivity) were measured at room temperature while the thermal diffusivity was measured at 177-192 C both before and after the irradiation and after each subsequent 2-h heat treatment at 350 C, 600, and 1000 C. The irradiation increased the resistivity significantly, but the thermal conductivity decreased only by about 10-15 percent. This tends to indicate that the radiation produced only small defects (single pairs and small vacancy chains). The samples all returned to almost exactly their preirradiation state after the 1000 C anneal. This indicates that SiGe alloys can be operated in this neutron fluence at high temperatures without a degradation of thermoelectric properties.

Vandersande, Jan W.↗
DOE OSTI2021

Manipulation of amorphous precursors to enhance zeolite nucleation

Crystallization in media comprised of amorphous precursors is becoming a more common phenomenon for numerous synthetic, biological, and natural materials that grow by a combination of classical and nonclassical pathways. Amorphous phases can exhibit a wide range of physicochemical properties that may evolve during the course of nucleation and crystal growth. This creates challenges for establishing causal relationships between amorphous precursor properties and their effect(s) on the selection of mechanistic pathways of crystallization and ultimately the properties of the crystalline product. In this study, we examine ways to manipulate the composition and colloidal stability of amorphous (alumino)silicate precursors that are prevalent in nanoporous zeolite syntheses. Changes in the amorphous precursor properties are evaluated on the basis of their ability to enhance rates of crystal formation. Here, we use fumed silica as the primary silicon source and examine the effects of infusing the source or growth medium with additional alkali metal, which serves as an inorganic structure-directing agent to facilitate the formation of porous crystal structures. We also assess the impact of adding a polymer additive, which reduces the colloidal stability of precursors, wherein we posit that the confined pockets of solution within the interstitial spaces of the precursor aggregates play an important role in regulating the rate of zeolite crystallization. Three commercially relevant zeolites (mordenite, SSZ-13, and ZSM-5) were selected for this study based on their diverse frameworks and methods of preparation. Here our findings reveal that alkali infusion significantly reduces the crystallization times for mordenite and SSZ-13, but has little impact on ZSM-5 synthesis. Conversely, we find that polymer addition markedly enhanced the rates of crystallization among all three zeolites, suggesting that this method may be a general approach to reduce zeolite synthesis times. Given the relatively high costs associated with commercial zeolite production, identifying new methods to improve the efficiency of hydrothermal syntheses can have significant practical implications beyond the fundamental benefits of developing new routes to tailor nonclassical crystallization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1994

Effects of Combined Stressing on the Electrical Properties of Film and Ceramic Capacitors

Advanced power systems which generate, control, and distribute electrical power to many large loads are a requirement for future space exploration missions. The development of high temperature insulating materials and power components constitute a key element in systems which are lightweight, efficient, and are capable of surviving the hostile space environment. In previous work, experiments were carried out to evaluate film and ceramic capacitors for potential use in high temperature applications. The effects of thermal stressing, in air and without electrical bias, on the electrical properties of the capacitors as a function of thermal aging up to 12 weeks were determined. In this work, the combined effects of thermal aging and electrical stresses on the properties of teflon film and ceramic power capacitors were examined. The ceramic capacitors were thermally aged for 35 weeks and the teflon capacitors for 15 weeks at 200 C under full electrical bias and were characterized, on a weekly basis, in terms of their capacitance stability and electrical loss in the frequency range of 50 Hz to 100 kHz. DC leakage current measurements were also obtained. The results obtained represent the influence that short-term thermal aging and electrical bias have on the electrical properties of the power capacitors characterized.

Overton, Eric↗
NASA NTRS1993

Defects in electro-optically active polymer solids

There is considerable current interest in the application of organic and polymeric materials for electronic and photonic devices. The rapid, non-linear optical (NLO) response of these materials makes them attractive candidates for waveguides, interferometers, and frequency doublers. In order to realize the full potential of these systems, it is necessary to develop processing schemes which can fabricate these molecules into ordered arrangements. There is enormous potential for introducing well-defined, local variations in microstructure to control the photonic properties of organic materials by rational 'defect engineering.' This effort may eventually become as technologically important as the manipulation of the electronic structure of solid-state silicon based devices is at present. The success of this endeavor will require complimentary efforts in the synthesis, processing, and characterization of new materials. Detailed information about local microstructure will be necessary to understand the influence of symmetry breaking of the solid phases near point, line, and planar defects. In metallic and inorganic polycrystalline materials, defects play an important role in modifying macroscopic properties. To understand the influence of particular defects on the properties of materials, it has proven useful to isolate the defect by creating bicrystals between two-component single crystals. In this way the geometry of a grain boundary defect and its effect on macroscopic properties can be determined unambiguously. In crystalline polymers it would be valuable to establish a similar depth of understanding about the relationship between defect structure and macroscopic properties. Conventionally processed crystalline polymers have small crystallites (10-20 nm), which implies a large defect density in the solid state. Although this means that defects may play an important or even dominant role in crystalline or liquid crystalline polymer systems, it also makes it difficult to isolate the effect of a particular boundary on a macroscopically observed property. However, the development of solid-state and thin-film polymerization mechanisms have facilitated the synthesis of highly organized and ordered polymers. These systems provide a unique opportunity to isolate and investigate in detail the structure of covalently bonded solids near defects and the effect of these defects on the properties of the material. The study of defects in solid polymers has been the subject of a recent review (Martin, 1993).

Martin, David C.↗
DOE OSTI2023

Effect of Volumetric Energy Density on Microstructure and Properties of Grade 300 Maraging Steel Fabricated by Laser Powder Bed Fusion

Here this study investigated the effect of laser powder bed fusion process parameters on the microstructure and properties of maraging steel. The results show that the process parameters can be finetuned to achieve both a high build rate/low hardness and low build rate/high hardness during fabrication, enabling the co-design of components where property gradients are desirable such as an injection molding tool where surface hardness is desired to be higher than the bulk, which needs to have higher fracture toughness.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Not all platinum surfaces are the same: Effect of the support on fundamental properties of platinum adlayer and its implications for the activity toward hydrogen evolution reaction

The adsorption of atomic hydrogen on a platinum monolayer supported on orthorhombic Mo 2 C(100) surface has been investigated, considering different hydrogen surface coverages. Calculations have been performed using density functional theory with the Perdew-Burke-Ernzerhof exchange correlation functional and a D3 Van der Waals corrections. The theoretical insight has been gained into atomic hydrogen interaction with Pt monolayer, supported on both molybdenum and well-studied tungsten carbide, and considering hydrogen surface coverage. Fundamental properties of Pt adlayer depend on the support, affecting hydrogen evolution activity of the resulting systems. At low hydrogen coverage all systems, with the exception of Pt supported on the molybdenum-terminated Mo 2 C, adsorb H comparably to a pristine Pt(111) surface and their high activity for the hydrogen evolution reaction is predicted. Additionally, at higher coverages supported Pt monolayers interact with atomic hydrogen unlike the Pt(111), suggesting that the activity of the supported and unsupported platinum toward hydrogen evolution reaction have different origins. Furthermore, the position of the supported platinum monolayers on the volcano curve is a function of the surface coverage, more so than for extended metal surfaces. Therefore, hydrogen surface coverage is a key variable to understand the catalytic potential, approaching towards an improved model for screening of electrocatalytic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Environmental barrier coatings on enhanced roughness SiC: Effect of plasma spraying conditions on properties and performance

Environmental barrier coatings for SiC/SiC composites are limited by the melting temperature of the Si bond coating near 1414°C. Systems without a bond coating may be required for future turbine applications where material temperatures go beyond 1350 °C. Here, enhanced roughness SiC substrates were developed to assess coating adhesion without the bond coating. Two EBCs with different YbMS/YbDS ratios were produced via modified plasma spraying parameters. Coating microstructure, thermal expansion, and modulus were measured for comparison of coating properties. Cyclic steam exposures at 1350°C were performed to assess oxidation resistance. The EBC with increased concentration of Yb 2 SiO 5 secondary phase displayed a higher CTE, which is typically expected to decrease adhesion lifetimes due to an increase in stress upon thermal cycling. Yet, the EBC chemistry with increased Yb 2 SiO 5 concentration was able to experience longer cycling times prior to coating delamination, likely due to interface interactions with the substrate and the thermally grown oxide.

36 MATERIALS SCIENCE↗