SEARCH · Engineering Papers

Results for “Dynamic Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

All sources NASA NTRS DOE OSTI

NASA NTRS1951

Tank Investigation of the EDO Model 142 Hydro-Ski Research Airplane

A tank investigation has been conducted of a 1/10-size powered-dynamic model of the Edo model 142 hydra-ski research airplane. The results of tests of two configurations are presented: One included a large ski and a ski well; the other, a small ski without a well. Water take-offs would be possible with the available thrust for either configuration: however, the configuration with the large ski emerged sooner and had less resistance from ski emergence until take-off. Longitudinal stability and landing behavior in smooth water were satisfactory for both configurations. Some alteration to the design of the tail would be desirable in order to reduce the spray loads.

Ramsen, John A.↗

NASA NTRS2011

Flight Simulation Model Exchange

The NASA Engineering and Safety Center Review Board sponsored an assessment of the draft Standard, Flight Dynamics Model Exchange Standard, BSR/ANSI-S-119-201x (S-119) that was conducted by simulation and guidance, navigation, and control engineers from several NASA Centers. The assessment team reviewed the conventions and formats spelled out in the draft Standard and the actual implementation of two example aerodynamic models (a subsonic F-16 and the HL-20 lifting body) encoded in the Extensible Markup Language grammar. During the implementation, the team kept records of lessons learned and provided feedback to the American Institute of Aeronautics and Astronautics Modeling and Simulation Technical Committee representative. This document contains the results of the assessment.

Murri, Daniel G.↗

NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbomachinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbopumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbomachinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test articles mimic a single inducer blade that is unwrapped from the hub, thus resembling a low aspect ratio cantilevered plate. To induce cavitation, the plates are oriented at a non-zero angle of attack and have rough strips near their leading edges. To control the extent of cavitation, the static pressure of the water tunnel is controlled between roughly 0.5 and 1.5 atm. A high-speed camera is used to quantify the coverage of the cavitations heet. The sheet coverage is then correlated to changes in fluid-added mass and hydroelstic damping. In addition, a corresponding two-way coupled CFD/FE model is under development for test/analysis correlation.

Ben Davis↗

NASA NTRS1984

On Choosing Between Two Probabilistic Choice Sub-models in a Dynamic Multitask Environment

An independent random utility model based on Thurstone's Theory of Comparative Judgment and a constant utility model based on Luce's Choice Axiom are reviewed in detail. Predictions from the two models are shown to be equivalent under certain restrictions on the distribution of the underlying random process. Each model is applied as a stochastic choice submodel in a dynamic, multitask, environment. Resulting choice probabilities are nearly identical, indicating that, despite their conceptual differences, neither model may be preferred over the other based solely on its predictive capability.

Soulsby, E. P.↗

NASA NTRS2012

SRMS Assisted Docking and Undocking for the Orbiter Repair Maneuver

As part of the Orbiter Repair Maneuver (ORM) planned for Return to Flight (RTF) operations, the Shuttle Remote Manipulator System (SRMS) must undock the Orbiter, maneuver it through a complex trajectory at extremely low rates, present it to an EVA crewman at the end of the Space Station Remote Manipulator System to perform the Thermal Protection System (TPS) repair, and then retrace back through the trajectory to dock the Orbiter with the Orbiter Docking System (ODS). The initial and final segments of this operation involve the interaction between the SRMS, ISS, Orbiter and ODS. Previously, a technique entitled "SRMS assisted docking" for installation of a payload to the ODS had been developed and was utilized for the Russian provided Docking Module on STS-74 during Shuttle-Mir missions and both the Node 1 and FGB elements on STS-88/Flight 2A. This procedure consisted of the SRMS grappling the respective payload, maneuvering it to a pre-install position inches above the ODS Androgynous Peripheral Attachment System (APAS) ring, commanding the SRMS into Test mode (which allows brakes-off motion of the joints), and then down-firing Primary Reaction Control System (PRCS) jets in order to effect a capture of the APAS latches. Once a successful capture had been achieved, then the AP AS was operated through its nominal retraction sequence to complete the mating sequence. While this technique can once again be used for the tail end docking portion of the ORM, the initial undocking of the orbiter and ISS vehicles with the assistance of the SRMS has yet to be attempted on orbit. The objective here is to determine the most efficient means to separate or extract the vehicles. Two techniques were analyzed in support of RTF: (1) the 'nominal' demating from the mated interface, and (2) the SRMS performing the operation (either in an active or passive fashion). In the first operation, the demating process would replicate standard undocking operations, with the exception that the SRMS is allowed to arrest the resulting motion. The second operation would be to extend the APAS ring to a ready to dock position, open the capture latches, and then detach the vehicles using the SRMS either actively or passively. In the active case, the APAS ring is extended and latched, and the SRMS is commanded to pull the two interfaces apart (assuming that the effective pull force of the SRMS can overcome the spec values of the combined latch resistance). In the passive case, the SRMS brakes are engaged and the AP AS mechanism is commanded to retract, pulling the two interfaces apart. Since the emphasis of both STS-74 and STS-88 had solely been on the installation operation, as opposed to the separation operation, two new models required development and incorporation within simulation tools designed to analyze those scenarios. These enhancements included: (1) a detailed demating dynamics model to characterize the pusher spring characteristics during undocking, and (2) contact and mechanical system modeling of the back side of the latches to represent unlatching dynamics. This paper first provides an overview of the Monte-Carlo screening analysis for the installation (both nominal and contingency), including the variation of separation distance, misalignment conditions, SRMS joint/brake parameter characteristics, and PRCS jet combinations and corresponding thrust durations. The resulting 'optimum' solution is presented based on trade studies between predicted capture success and integrated system loads. This paper then discusses the upgrades to the APAS math model associated with the new SRMS assisted undocking technique and reviews simulation results for various options investigated for either the active and passive separation of the ISS from the Orbiter.

Space Station Remote Manipulator System↗

NASA NTRS1981

Operating manual holographic interferometry system for 2 x 2 foot transonic wind tunnel

A holographic interferometer system was installed in a 2X2 foot transonic wind tunnel. The system incorporates a modern, 10 pps, Nd:YAG pulsed laser which provides reliable operation and is easy to align. The spatial filtering requirements of the unstable resonator beam are described as well as the integration of the system into the existing Schieren system. A two plate holographic interferometer is used to reconstruct flow field data. For static wind tunnel models the single exposure holograms are recorded in the usual manner; however, for dynamic models such as oscillating airfoils, synchronous laser hologram recording is used.

Craig, J. E.↗

NASA NTRS1983

Flight directors for STOl aircraft

Flight director logic for flight path and airspeed control of a powered-lift STOL aircraft in the approach, transition, and landing configurations are developed. The methods for flight director design are investigated. The first method is based on the Optimal Control Model (OCM) of the pilot. The second method, proposed here, uses a fixed dynamic model of the pilot in a state space formulation similar to that of the OCM, and includes a pilot work-load metric. Several design examples are presented with various aircraft, sensor, and control configurations. These examples show the strong impact of throttle effectiveness on the performance and pilot work-load associated with manual control of powered-lift aircraft during approach. Improved performed and reduced pilot work-load can be achieved by using direct-lift-control to increase throttle effectiveness.

Rabin, U. H.↗

NASA NTRS1983

Nd:YAG holographic interferometer for aerodynamic research

A holographic interferometer system has been installed in the NASA Ames 2- by 2-Foot Transonic Wind Tunnel. The system incorporates a modern 10 pps, Nd:YAG pulsed laser which provides reliable operation and is easy to align. The spatial filtering requirements of the unstable resonator beam are described, as well as the integration of the system into the existing schlieren system. A two-plate holographic interferometer is used to reconstruct flow field data. For static wind tunnel models, the single exposure holograms are recorded in the usual manner; however, for dynamic models such as oscillating airfoils, synchronous laser hologram recording is used.

Craig, J. E.↗

NASA NTRS1985

Multi-input, multi-output system control for experimental aircraft

Two techniques, direct eigenspace assignment (DEA) and explicit model following (EMF), are used initially to synthesize control laws for the longitudinal dynamics model of a Short Takeoff and Landing (STOL) vehicle in the landing configuration. The vehicle model and the flight control design are presented. The two synthesis techniques are briefly discussed and the handling qualities specifications mapped into the algorithm formulations. The control laws resulting from exercising the algorithms are evaluated in terms of achieved performance and robustness. Since the synthesized control laws involve full state feedback, methodologies were implemented for the control laws using output feedback without adversely affecting performance and robustness. Finally, the salient features of the two design techniques are summarized and the areas that require further investigation are suggested.

Schmidt, D. K.↗

NASA NTRS1987

Giotto-spacecraft charging due to impact generated plasma in the presence of dielectric materials

The charging effects of a conducting/dielectric model spacecraft in the impact induced plasma environment are contrasted. The results of dynamic model calculations indicate larger charging times and higher positive spacecraft potentials for a conducting/dielectric spacecraft. The potential and particle distributions around the spacecraft differ quantitatively and qualitatively in both cases.

Thiemann, H.↗

NASA NTRS1989

Determination of joint drives for stable end-effector motion in flexible robotic systems

The prescribed tasks in high speed robotic systems are severely deteriorated because of their manipulator dynamic deflections. On the other hand conventional dynamic modeling techniques fail to reveal appropriate control forces in flexible systems. The conventional dynamic equations of motion for systems subject to kinematical constraints are modified by a new concept of control force representation. The directions of the control forces are selected such that they correspond to the joint degrees of freedom. Then the joint control forces and torques that yield unperturbed prescribed motions are solved simultaneously with the system motion. A flexible manipulator is presented to illustrate the methods proposed.

Ider, Sitki Kemal↗

NASA NTRS1991

Effect of motor dynamics on nonlinear feedback robot arm control

A nonlinear feedback robot controller that incorporates the robot manipulator dynamics and the robot joint motor dynamics is proposed. The manipulator dynamics and the motor dynamics are coupled to obtain a third-order-dynamic model, and differential geometric control theory is applied to produce a linearized and decoupled robot controller. The derived robot controller operates in the robot task space, thus eliminating the need for decomposition of motion commands into robot joint space commands. Computer simulations are performed to verify the feasibility of the proposed robot controller. The controller is further experimentally evaluated on the PUMA 560 robot arm. The experiments show that the proposed controller produces good trajectory tracking performances and is robust in the presence of model inaccuracies. Compared with a nonlinear feedback robot controller based on the manipulator dynamics only, the proposed robot controller yields conspicuously improved performance.

Tarn, Tzyh-Jong↗

NASA NTRS1992

Effect of type of load on stress analysis of thin-walled ducts

The standard procedure for qualifying the design of duct (pipe) systems in the Space Shuttle Main Engine (SSME) has been fairly well defined. However, since pipe elbows are quite common and important in the SSME duct systems, a clear understanding of the detailed stress profile of the components is necessary for accurate structural and life assessments. This study was initiated to predict the stress profile at/near the tangent point along the cross section of the duct under various types of loads. Also, this study was further extended to understand the stiffening effect on stresses due to pressure at the tangent point. The intention of this study was to identify the importance of selecting proper locations for mounting strain gauges and to utilize the obtained results to anchor dynamic models for accurate structural and life assessments of the SSME ducts under a dynamic environment. The finite element method was utilized in this study.

Min, J. B.↗

NASA NTRS1992

The Mars water cycle at other epochs: Recent history of the polar caps and layered terrain

The Martian polar caps and layered terrain presumably evolves by the deposition and removal of small amounts of water and dust each year, the current cap attributes therefore represent the incremental transport during a single year as integrated over long periods of time. The role was studied of condensation and sublimation of water ice in this process by examining the seasonal water cycle during the last 10(exp 7) yr. In the model, axial obliquity, eccentricity, and L sub s of perihelion vary according to dynamical models. At each epoch, the seasonal variations in temperature are calculated at the two poles, keeping track of the seasonal CO2 cap and the summertime sublimation of water vapor into the atmosphere; net exchange of water between the two caps is calculated based on the difference in the summertime sublimation between the two caps (or on the sublimation from one cap if the other is covered with CO2 frost all year). Results from the model can help to explain (1) the apparent inconsistency between the timescales inferred for layer formation and the much older crater retention age of the cap and (2) the difference in sizes of the two residual caps, with the south being smaller than the north.

Jakosky, Bruce M.↗

NASA NTRS1993

Design and analysis of numerical experiments

Methods for the design and analysis of numerical experiments that are especially useful and efficient in multidimensional parameter spaces are presented. The analysis method, which is similar to kriging in the spatial analysis literature, fits a statistical model to the output of the numerical model. The method is applied to a fully nonlinear, global, equivalent-barotropic dynamical model. The statistical model also provides estimates for the uncertainty of predicted numerical model output, which can provide guidance on where in the parameter space to conduct further experiments, if necessary. The method can provide significant improvements in the efficiency with which numerical sensitivity experiments are conducted.

Bowman, Kenneth P.↗

NASA NTRS1995

Modeling the vestibulo-ocular reflex of the squirrel monkey during eccentric rotation and roll tilt

Model simulations of the squirrel monkey vestibulo-ocular reflex (VOR) are presented for two motion paradigms: constant velocity eccentric rotation and roll tilt about a naso-occipital axis. The model represents the implementation of three hypotheses: the "internal model" hypothesis, the "gravito-inertial force (GIF) resolution" hypothesis, and the "compensatory VOR" hypothesis. The internal model hypothesis is based on the idea that the nervous system knows the dynamics of the sensory systems and implements this knowledge as an internal dynamic model. The GIF resolution hypothesis is based on the idea that the nervous system knows that gravity minus linear acceleration equals GIF and implements this knowledge by resolving the otolith measurement of GIF into central estimates of gravity and linear acceleration, such that the central estimate of gravity minus the central estimate of acceleration equals the otolith measurement of GIF. The compensatory VOR hypothesis is based on the idea that the VOR compensates for the central estimates of angular velocity and linear velocity, which sum in a near-linear manner. During constant velocity eccentric rotation, the model correctly predicts that: (1) the peak horizontal response is greater while "facing-motion" than with "back-to-motion"; (2) the axis of eye rotation shifts toward alignment with GIF; and (3) a continuous vertical response, slow phase downward, exists prior to deceleration. The model also correctly predicts that a torsional response during the roll rotation is the only velocity response observed during roll rotations about a naso-occipital axis. The success of this model in predicting the observed experimental responses suggests that the model captures the essence of the complex sensory interactions engendered by eccentric rotation and roll tilt.

NASA Discipline Neuroscience↗

NASA NTRS2007

General Mission Analysis Tool (GMAT) Acceptance Test Plan [Draft]

The information presented in this Acceptance Test Plan document shows the current status of the General Mission Analysis Tool (GMAT). GMAT is a software system developed by NASA Goddard Space Flight Center (GSFC) in collaboration with the private sector. The GMAT development team continuously performs acceptance tests in order to verify that the software continues to operate properly after updates are made. The GMAT Development team consists of NASA/GSFC Code 583 software developers, NASA/GSFC Code 595 analysts, and contractors of varying professions. GMAT was developed to provide a development approach that maintains involvement from the private sector and academia, encourages collaborative funding from multiple government agencies and the private sector, and promotes the transfer of technology from government funded research to the private sector. GMAT contains many capabilities, such as integrated formation flying modeling and MATLAB compatibility. The propagation capabilities in GMAT allow for fully coupled dynamics modeling of multiple spacecraft, in any flight regime. Other capabilities in GMAT inclucle: user definable coordinate systems, 3-D graphics in any coordinate system GMAT can calculate, 2-D plots, branch commands, solvers, optimizers, GMAT functions, planetary ephemeris sources including DE405, DE200, SLP and analytic models, script events, impulsive and finite maneuver models, and many more. GMAT runs on Windows, Mac, and Linux platforms. Both the Graphical User Interface (GUI) and the GMAT engine were built and tested on all of the mentioned platforms. GMAT was designed for intuitive use from both the GUI and with an importable script language similar to that of MATLAB.

Dove, Edwin↗

NASA NTRS2003

Reconstruction of the Voyager Saturn Encounter orbits in the ICRF system

We obtain Voyager trajectories in the International Celestial Reference Frame, and we revise the gravity field taking advantage of improvements made in modelling and data processing since the previous work. We also incorporate a full dynamical model for the Saturnian satellites into the analysis for the first time.

Voyager↗