Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dimensionality Reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Flight tests of external modifications used to reduce blunt base drag

The effectiveness of a trailing disk (the trapped vortex concept) in reducing the blunt base drag of an 8-in diameter body of revolution was studied from measurements made both in flight and in full-scale wind-tunnel tests. The experiment demonstrated the significant base drag reduction capability of the trailing disk to Mach 0.93. The maximum base drag reduction obtained from a cavity tested on the flight body of revolution was not significant. The effectiveness of a splitter plate and a vented-wall cavity in reducing the base drag of a quasi-two-dimensional fuselage closure was studied from base pressure measurements made in flight. The fuselage closure was between the two engines of the F-111 airplane; therefore, the base pressures were in the presence of jet engine exhaust. For Mach numbers from 1.10 to 1.51, significant base drag reduction was provided by the vented-wall cavity configuration. The splitter plate was not considered effective in reducing base drag at any Mach number tested.

Powers, Sheryll Goecke↗
NASA NTRS1990

Viscous drag reduction via surface mass injection

Slot injection systems on the surfaces of aerodynamic bodies have been noted to consistently furnish substantial local skin friction reductions which are predictable on the basis of current numerical methods. Only crude systems studies, however, have been thus far completed. The most common configuration for slot ingestion in the literature involves tangential injection of air along a two-dimensional surface on which air constitutes the mainstream flow; attention is presently given to slot injection in low-speed and high-speed flows, as well as a discussion of aircraft applications and an evaluation of prospective possibilities for practical drag-reduction systems.

Hefner, Jerry N.↗
DOE OSTI2014

Dendritic Assembly of Gold Nanoparticles during Fuel-Forming Electrocatalysis

We report on the dendritic assembly of alkanethiol-capped gold nanoparticles on a glassy carbon support during electrochemical reduction of protons and CO 2 . We discovered that the primary mechanism by which surfactant-ligated gold nanoparticles lose surface area is by taking a random walk along the support, colliding with their neighbors, and fusing to form dendrites, a type of fractal aggregate. A random walk model reproduces the fractal dimensionality of the dendrites observed experimentally. The rate at which the dendrites form is strongly dependent on the solubility of the surfactant in the electrochemical double layer under the conditions of electrolysis. Since alkanethiolate surfactants reductively desorb at potentials close to the onset of CO 2 reduction, they do not poison the catalytic activity of the gold nanoparticles. While catalyst mobility is typically thought to be limited for room-temperature electrochemistry, our results reflect that nanoparticle mobility is significant under conditions at which they electrochemically catalyze gas evolution, even in the presence of a high surface area carbon and binder. A careful understanding of the electrolyte- and polarization-dependent nanoparticle aggregation kinetics informs strategies for maintaining catalyst dispersion during fuel-forming electrocatalysis.

dendrons↗
DOE OSTI2020

Carbon Nanotube Formation on Cr-Doped Ferrite Catalyst during Water Gas Shift Membrane Reaction: Mechanistic Implications and Extended Studies on Dry Gas Conversions

A nanocrystalline chromium-doped ferrite (FeCr) catalyst was shown to coproduce H2 and multiwalled carbon nanotubes (MWCNTs) during water gas shift (WGS) reaction in a H2-permselective zeolite membrane reactor (MR) at reaction pressures of ~20 bar. The FeCr catalyst was further demonstrated in the synthesis of highly crystalline and dimensionally uniform MWCNTs from a dry gas mixture of CO and CH4, which were the apparent sources for MWCNT growth in the WGS MR. In both the WGS MR and dry gas reactions, the operating temperature was 500 °C, which is significantly lower than those commonly used in MWCNT production by chemical vapor deposition (CVD) method from CO, CH4, or any other precursor gases. Extensive ex situ characterizations of the reaction products revealed that the FeCr catalyst remained in partially reduced states of Fe3+/Fe2+ and Cr6+/Cr3+ in WGS membrane reaction while further reduction of Fe2+ to Fe0 occurred in the CO/CH4 dry gas environments. The formation of the metallic Fe nanoparticles or catalyst surface dramatically improved the crystallinity and dimensional uniformity of the MWCNTs from dry gas reaction as compared to that from WGS reaction in the MR. Reaction of the CO/CH4 mixture containing 500 ppmv H2S also resulted in high-quality MWCNTs similar to those from the H2S-free feed gas, demonstrating excellent sulfur tolerance of the FeCr catalyst that is practically meaningful for utilization of biogas and cheap coal-derived syngas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2013

Iron-reducing bacteria accumulate ferric oxyhydroxide nanoparticle aggregates that may support planktonic growth

Iron-reducing bacteria (FeRB) play key roles in anaerobic metal and carbon cycling and carry out biogeochemical transformations that can be harnessed for environmental bioremediation. A subset of FeRB require direct contact with Fe(III) bearing minerals for dissimilatory growth, yet these bacteria must move between mineral particles. Further, they proliferate in planktonic consortia during biostimulation experiments. Thus, a key question is how such organisms can sustain growth under these conditions. Here we characterized planktonic microbial communities sampled from an aquifer in Rifle, Colorado, USA close to the peak of iron reduction following in situ acetate amendment. Samples were cryo-plunged on site and subsequently examined using correlated 2- and 3- dimensional cryogenic transmission electron microscopy (cryo-TEM) and scanning transmission X-ray microscopy (STXM). Most cells had their outer membranes decorated with up to 150 nm diameter aggregates composed of a few nm wide amorphous, Fe-rich nanoparticles. Fluorescent in situ hybridization of lineage-specific probes applied to rRNA of cells subsequently imaged via cryo-TEM identified Geobacter spp., a well studied group of FeRB. STXM results at the Fe L2,3 absorption edges indicate that nanoparticle aggregates contain a variable mixture of Fe(II)-Fe(III), and are generally enriched in Fe(III). Geobacter bemidjiensis cultivated anaerobically in the laboratory on acetate and hydrous ferric oxyhydroxides also accumulated mixed valence nanoparticle aggregates. In field-collected samples, FeRB with a wide variety of morphologies were associated with nano-aggregates, indicating that cell-surface Fe(III) accumulation may be a general mechanism by which FeRB can grow while in planktonic suspension.

biomineralization↗
DOE OSTI2024

Angle between DNA linker and nucleosome core particle regulates array compaction revealed by individual-particle cryo-electron tomography

Abstract The conformational dynamics of nucleosome arrays generate a diverse spectrum of microscopic states, posing challenges to their structural determination. Leveraging cryogenic electron tomography (cryo-ET), we determine the three-dimensional (3D) structures of individual mononucleosomes and arrays comprising di-, tri-, and tetranucleosomes. By slowing the rate of condensation through a reduction in ionic strength, we probe the intra-array structural transitions that precede inter-array interactions and liquid droplet formation. Under these conditions, the arrays exhibite irregular zig-zag conformations with loose packing. Increasing the ionic strength promoted intra-array compaction, yet we do not observe the previously reported regular 30-nanometer fibers. Interestingly, the presence of H1 do not induce array compaction; instead, one-third of the arrays display nucleosomes invaded by foreign DNA, suggesting an alternative role for H1 in chromatin network construction. We also find that the crucial parameter determining the structure adopted by chromatin arrays is the angle between the entry and exit of the DNA and the corresponding tangents to the nucleosomal disc. Our results provide insights into the initial stages of intra-array compaction, a critical precursor to condensation in the regulation of chromatin organization.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Subsurface hydrogen, curvature, and strain: lessons from electro-reduction of benzaldehyde on nano-structured Pd catalysts

The unique ability of palladium (Pd) to absorb hydrogen and form a bulk hydride is vital for chemical transformations that involve hydrogenation reactions. Nano-structured Pd catalysts offer a promise of tuning these reaction rates by exploiting variations of reactant binding energies depending on the surface structure and morphological constraints that result in inhomogeneous strain. However, the interplay between the nano-structure of Pd and the ability of Pd to adsorb (and absorb) hydrogen as well as other reactive species needs to be better understood for a rational understanding of competitive chemical transformations at Pd surfaces. We consider the effects of the surface corrugation, strain, and subsurface Pd hydride on the reduction of benzaldehyde to benzyl alcohol in two qualitatively different samples – Pd nanoparticles and Pd gels formed by quasi-one-dimensional chains of these nanoparticles. Our electrochemical measurements and computational modelling suggest that surface concave sites, inherent to Pd gels, facilitate hydrogen transfer to the Pd subsurface region, thus weakening benzaldehyde binding to the surface. This effect is further modulated by the strain, depending on the local coordination environment on the corrugated surface. Furthermore, these findings demonstrate how structurally complex samples in the form of gels provide degrees of freedom for controlling the behavior of metal catalysts that are not available in isolated nanoparticles, which paves the way for new approaches in the design of catalytic materials and synthesis of metal hydrides.

Padavala, Sri Krishna Murthy [University of Minnes↗
DOE OSTI2013

On the small divergence of laser-driven ion beams from nanometer thick foils

We report on experimental studies of divergence of proton beams from nanometer thick diamond-like carbon foils irradiated by a linearly polarized intense laser with high contrast. Proton beams with extremely small divergence (half angle) of 2° are observed in addition with a remarkably well-collimated feature over the whole energy range, showing one order of magnitude reduction of the divergence angle in comparison to the results from μm thick targets. Similar features are reproduced in two-dimensional particle-in-cell simulations with parameters representing our experiments, indicating a strong influence from the electron density distribution on the divergence of protons. Our comprehensive experimental study reveals grand opportunities for using nm foils in experiments that require high ion flux and small divergence.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Reduction of blob-filament radial propagation by parallel variation of flows: Analysis of a gyrokinetic simulation

Data from the XGC1 gyrokinetic simulation is analyzed to understand the three-dimensional spatial structure and the radial propagation of blob-filaments generated by quasisteady turbulence in the tokamak edge pedestal and scrape-off layer plasma. Spontaneous toroidal flows vary in the poloidal direction and shear the filaments within a flux surface resulting in a structure that varies in the parallel direction. Here, this parallel structure allows the curvature and grad-B induced polarization charge density to be shorted out via parallel electron motion. As a result, it is found that the blob-filament radial velocity is significantly reduced from estimates which neglect parallel electron kinetics, broadly consistent with experimental observations. Conditions for when this charge shorting effect tends to dominate blob dynamics are derived and compared with the simulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2012

A fully 3D approach for metal artifact reduction in computed tomography

Purpose: In computed tomography imaging metal objects in the region of interest introduce inconsistencies during data acquisition. Reconstructing these data leads to an image in spatial domain including star-shaped or stripe-like artifacts. In order to enhance the quality of the resulting image the influence of the metal objects can be reduced. Here, a metal artifact reduction (MAR) approach is proposed that is based on a recomputation of the inconsistent projection data using a fully three-dimensional Fourier-based interpolation. The success of the projection space restoration depends sensitively on a sensible continuation of neighboring structures into the recomputed area. Fortunately, structural information of the entire data is inherently included in the Fourier space of the data. This can be used for a reasonable recomputation of the inconsistent projection data. Methods: The key step of the proposed MAR strategy is the recomputation of the inconsistent projection data based on an interpolation using nonequispaced fast Fourier transforms (NFFT). The NFFT interpolation can be applied in arbitrary dimension. The approach overcomes the problem of adequate neighborhood definitions on irregular grids, since this is inherently given through the usage of higher dimensional Fourier transforms. Here, applications up to the third interpolation dimension are presented and validated. Furthermore, prior knowledge may be included by an appropriate damping of the transform during the interpolation step. This MAR method is applicable on each angular view of a detector row, on two-dimensional projection data as well as on three-dimensional projection data, e.g., a set of sequential acquisitions at different spatial positions, projection data of a spiral acquisition, or cone-beam projection data. Results: Results of the novel MAR scheme based on one-, two-, and three-dimensional NFFT interpolations are presented. All results are compared in projection data space and spatial domain with the well-known one-dimensional linear interpolation strategy. Conclusions: In conclusion, it is recommended to include as much spatial information into the recomputation step as possible. This is realized by increasing the dimension of the NFFT. The resulting image quality can be enhanced considerably.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Electrochemical Dilatometry of Si-Bearing Electrodes: Dimensional Changes and Experiment Design

The severe volumetric changes in Si particles during the Li (de)alloying process cause expansion and contraction of the electrodes, which along with excessive electrolyte reduction and solid electrolyte interphase formation brings about rapid decay in cell capacity. In this work, we use operando electrochemical dilatometry to quantify the (de)lithiation-induced expansion/contraction of Si-based and graphite-rich electrodes during electrochemical cycling. We evaluate the relationship between electrode capacity and dilation and observe that by increasing the Si contribution to the electrode capacity, the swelling is aggravated upon lithiation. For silicon-rich anodes, the electrode dilation can be higher than 300%, and the expansion profile consists of a combination of slow swelling at low lithiation followed by an accelerated increase at higher lithium contents. We investigate how electrode properties, such as porosity, affect the dilation profile and quantify the irreversible expansion of the electrodes. Finally, we discuss some of the challenges associated with the dilatometry technique and suggest experimental approaches for obtaining consistent and reliable data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1976

Development of relaxation turbulence models

Relaxation turbulence models have been intensively studied. The complete time dependent mass averaged Navier-Stokes equations have been solved for flow into a two dimensional compression corner. A new numerical scheme has been incorporated into the developed computed code with an attendant order of magnitude reduction in computation time. Computed solutions are compared with experimental measurements of Law for supersonic flow. Details of the relaxation process have been studied; several different relaxation models, including different relaxation processes and varying relaxation length, are tested and compared. Then a parametric study has been conducted in which both Reynolds number and wedge angle are varied. To assess effects of Reynolds number and wedge angle, the parametric study includes the comparison of computed separation location and upstream extent of pressure rise; numerical results are also compared with the measurements of surface pressure, skin friction and mean velocity field.

Hung, C. M.↗
NASA NTRS1976

The effect of varying freestream velocity on dynamic stall characteristics

A low speed wind tunnel equipped with an axial gust generator to simulate the aerodynamic environment of a helicopter rotor was used to study the dynamic stall of a pitching blade. The objective of this investigation was to find out to what extent harmonic velocity perturbations in the freestream affect dynamic stall. The study involved making measurements of the aerodynamic moment on a two-dimensional, pitching blade model in both constant and pulsating airstreams. Using an operational analog computer to perform on-line data reduction, plots of moment versus angle of attack and work done by the moment were obtained. The data taken in the varying freestream were then compared to constant freestream data, and to the results of two analytical methods. These comparisons showed that the velocity perturbations had a significant effect on the pitching moment which could not be consistently predicted by the analytical methods, but had no drastic effect on the blade stability.

Pierce, G. A.↗
NASA NTRS1981

Mean-flow and turbulence measurements in the vicinity of the trailing edge of an NACA (63 sub 1)-012 airfoil

The Langley aircraft noise reduction laboratory was used to measure mean flow and turbulence in the vicinity of a cusped-trailing edge of two dimensional NACA 631-012 airfoil at zero angle of attack. Naturally transitioned flow and artificially tripped flow were investigated. Flow regions studied include the boundary layer and the near wake. Measurements were made at a free stream Reynolds number based on airfoil chord of 1.25 x 10 to the 6th power and a free stream Mach number of 0.1. Distributions of streamwise mean velocity, integral properties of the mean flow, turbulent intensities, and Reynolds shear stress are reported. For the naturally transitioned flow, the general trends observed are similar to those reported for a fully developed turbulent boundary layer over a flat plate under zero pressure gradient, with the exception of the notable streamwise variations in the turbulence properties for the airfoil flow. The main effect of flow tripping is to eliminate these streamwise variations. Observed changes in the mean flow and turbulence fields caused by tripping are expected on the basis of the Reynolds number based on the boundary layer thickness.

Yu, J. C.↗
NASA NTRS1985

A tomographic technique for aerodynamics at transonic speeds

Computer aided tomography (CAT) provides a means of noninvasively measuring the air density distribution around an aerodynamic model. This technique is global in that a large portion of the flow field can be measured. A test of the applicability of CAT to transonic velocities was studied. A hemispherical-nose cylinder afterbody model was tested at a Mach number of 0.8 with a new laser holographic interferometer at the 2- by 2-Foot Transonic Wind Tunnel. Holograms of the flow field were taken and were reconstructed into interferograms. The fringe distribution (a measure of the local densities) was digitized for subsequent data reduction. A computer program based on the Fourier-transform technique was developed to convert the fringe distribution into three-dimensional densities around the model. Theoretical aerodynamic densities were calculated for evaluating and assessing the accuracy of the data obtained from the tomographic method.

Lee, G.↗
NASA NTRS1985

Holographic interferometry applied to symmetric aerodynamic models in a wind tunnel

The technique of holographic interferometry provides a means for noninvasive measurement of the air density distribution in the flow field in the vicinity of an aerodynamic model. A test of the applicability of this technique was the objective of this investigation. A holographic interferometer was installed in the 2- by 2-Foot Transonic Wind Tunnel at Ames Research Center. Several tests were conducted with this system on two axisymmetric models, one at subsonic and the other at supersonic speeds. Holograms were made of the flow field around the model for several test conditions. These holograms were reconstructed into interferograms in the laboratory. The fringe distribution (a measure of local densities) from a number of interferograms was digitized for subsequent data reduction. A computer program based on the Fourier transform technique was developed to convert the fringe distribution into a three-dimensional distribution of air density around the model. These results will be presented in this paper.

Perry, R. L.↗
NASA NTRS1985

A tomographic technique for aerodynamics at transonic speeds

Computer aided tomography (CAT) provides a means of noninvasively measuring the air density distribution around an aerodynamic model. This technique is global in that a large portion of the flow field can be measured. A test of the applicability of CAT to transonic velocities was studied. A hemispherical-nose cylinder afterbody model was tested at a Mach number of 0.8 with a new laser holographic interferometer at the 2- by 2-Foot Transonic Wind Tunnel. Holograms of the flow field were taken and were reconstructed into interferograms. The fringe distribution (a measure of the local densities) was digitized for subsequent data reduction. A computer program based on the Fourier-transform technique was developed to convert the fringe distribution into three-dimensional densities around the model. Theoretical aerodynamic densities were calculated for evaluating and assessing the accuracy of the data obtained from the tomographic method.

Lee, G.↗