Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DATA CORRELATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Investigation of correlation between full-scale and fifth-scale wind tunnel tests of a Bell helicopter Textron Model 222

Reasons for lack of correlation between data from a fifth-scale wind tunnel test of the Bell Helicopter Textron Model 222 and a full-scale test of the model 222 prototype in the NASA Ames 40-by 80-foot tunnel were investigated. This investigation centered around a carefully designed fifth-scale wind tunnel test of an accurately contoured model of the Model 222 prototype mounted on a replica of the full-scale mounting system. The improvement in correlation for drag characteristics in pitch and yaw with the fifth-scale model mounted on the replica system is shown. Interference between the model and mounting system was identified as a significant effect and was concluded to be a primary cause of the lack of correlation in the earlier tests.

Squires, P. K.↗

Orion MPCV Continuum RCS Heating Augmentation Model Development

The reaction control system jets of the Orion Multi Purpose Crew Vehicle can have a significant impact on the magnitude and distribution of the surface heat flux on the leeside of the aft-body, when they are fired. Changes in surface heating are expressed in terms of augmentation factor over the baseline smooth body heating. Wind tunnel tests revealed heating augmentation factors as high as 13.0, 7.6, 2.8, and 5.8 for the roll, pitch down, pitch up, and yaw jets respectively. Heating augmentation factor models, based almost exclusively on data from a series of wind tunnel tests have been developed, for the purposes of thermal protection system design. The wind tunnel tests investigated several potential jet-to-freestream similarity parameters, and heating augmentation factors derived from the data showed correlation with the jet-to-freestream momentum ratio. However, this correlation was not utilized in the developed models. Instead augmentation factors were held constant throughout the potential trajectory space. This simplification was driven by the fact that ground to flight traceability and sting effects are not well understood. Given the sensitivity of the reaction control system jet heating augmentation to configuration, geometry, and orientation the focus in the present paper is on the methodology used to develop the models and the lessons learned from the data. The models that are outlined in the present work are specific to the aerothermal database used to design the thermal protection system for the Exploration Flight Test 1 vehicle.

Heating Augmentation↗

Plasmonic Conducting Metal Oxide-Based Optical Fiber Sensors for Chemical and Intermediate Temperature-Sensing Applications

The demand for real-time sensors in harsh environments at elevated temperature is significant and increasing. In this manuscript, the chemical and temperature sensing using the optical response through the practical fiber platform is demonstrated, and principle component analysis is coupled with targeted experimental film characterization to understand the fundamental sensing layer properties, which dominate measured gas sensing responses in complex gas mixtures. More specifically, tin-doped indium oxide-decorated sensors fabricated with the sol–gel method show stable and stepwise transmission responses varying over a wide range of H2 concentration (5–100%) at 250–350 °C as well as responses to CH4 and CO to a lesser extent. Measured responses are attributed to modifications to the surface plasmon resonance absorption in the near-infrared range and are dominated by the highest concentrations of the most-reducing analyte based upon systematic mixed gas stream experiments. Principal component analysis is utilized for this type of sensor to improve the quantitative and qualitative understanding of responses, clearly identifying that the dominant principle component (PC #1) accounts for ~78% of total data variance. Correlations between PC #1 and the experimentally derived free carrier concentration confirm that this material property plays the strongest role on the ITO gas sensing mechanism, while correlations between the free carrier mobility and the second most important principle component (PC #2) suggest that this quantity may play a significant but secondary role. As such, the results presented here clarify the relationship between generalized principle components and fundamental sensing materials properties thereby suggesting the pathway toward improved multicomponent gas speciation through sensor layer engineering. Furthermore, the work presented represents a significant step toward the ultimate objective of optical waveguide sensors integrated with multivariate data analytics for multiparameter monitoring with a single sensor element.

47 OTHER INSTRUMENTATION↗

Four-dimensional volume-of-interest reconstruction for cone-beam computed tomography-guided radiation therapy

Purpose: Data sufficiency are a major problem in four-dimensional cone-beam computed tomography (4D-CBCT) on linear accelerator-integrated scanners for image-guided radiotherapy. Scan times must be in the range of 4-6 min to avoid undersampling artifacts. Various image reconstruction algorithms have been proposed to accommodate undersampled data acquisitions, but these algorithms are computationally expensive, may require long reconstruction times, and may require algorithm parameters to be optimized. The authors present a novel reconstruction method, 4D volume-of-interest (4D-VOI) reconstruction which suppresses undersampling artifacts and resolves lung tumor motion for undersampled 1-min scans. The 4D-VOI reconstruction is much less computationally expensive than other 4D-CBCT algorithms. Methods: The 4D-VOI method uses respiration-correlated projection data to reconstruct a four-dimensional (4D) image inside a VOI containing the moving tumor, and uncorrelated projection data to reconstruct a three-dimensional (3D) image outside the VOI. Anatomical motion is resolved inside the VOI and blurred outside the VOI. The authors acquired a 1-min. scan of an anthropomorphic chest phantom containing a moving water-filled sphere. The authors also used previously acquired 1-min scans for two lung cancer patients who had received CBCT-guided radiation therapy. The same raw data were used to test and compare the 4D-VOI reconstruction with the standard 4D reconstruction and the McKinnon-Bates (MB) reconstruction algorithms. Results: Both the 4D-VOI and the MB reconstructions suppress nearly all the streak artifacts compared with the standard 4D reconstruction, but the 4D-VOI has 3-8 times greater contrast-to-noise ratio than the MB reconstruction. In the dynamic chest phantom study, the 4D-VOI and the standard 4D reconstructions both resolved a moving sphere with an 18 mm displacement. The 4D-VOI reconstruction shows a motion blur of only 3 mm, whereas the MB reconstruction shows a motion blur of 13 mm. With graphics processing unit hardware used to accelerate computations, the 4D-VOI reconstruction required a 40-s reconstruction time. Conclusions: 4D-VOI reconstruction effectively reduces undersampling artifacts and resolves lung tumor motion in 4D-CBCT. The 4D-VOI reconstruction is computationally inexpensive compared with more sophisticated iterative algorithms. Compared with these algorithms, our 4D-VOI reconstruction is an attractive alternative in 4D-CBCT for reconstructing target motion without generating numerous streak artifacts.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Model and full-scale large transport airframe noise

Results are presented for an airframe noise experiment intended to obtain airframe noise data of a 0.03-scale model of a large transport aircraft in a flow facility for comparison with similar airframe noise data from full-scale flyover tests of the same aircraft. The test model simulated the landing and cruise configuration, including individual flap systems. Considerable noise is found to be associated with the extension of the model's leading edge flap system and to be reduced across the noise spectra when the gaps between the leading-edge flaps and the leading edge of the wing are sealed. Amplitude and frequency scaling relationships are developed which correlate respective data for a variety of aircraft configurations. Normalized model landing gear noise failed to simulate full-scale data.

Shearin, J. G.↗

Modern energy density functional for nuclei and the nuclear matter equation of state

We discuss a method of determining a modern energy density functional (EDF) in nuclei. We adopt a Skyrme type EDF and fit the Skyrme parameters to an extensive set of experimental data on the ground-state binding energies, radii, and the breathing mode energies of a wide range of nuclei. We further constrain the values of the Skyrme parameters by requiring positive values for the slope of the symmetry energy S, the enhancement factor {kappa}, associated with the isovector giant dipole resonance, and the Landau parameter G{sub 0}{sup '}. This is done within the approaches of Hartree-Fock (HF) and HF with the inclusion of correlation effects, using a simulated-annealing based algorithm forminimizing {chi}{sup 2}.We also present results of HF based random phase approximation for the excitation strength function of the breathing mode and discuss the current status of the nuclear matter incompressibility coefficient.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Constraining level densities through quantitative correlations with cross-section data

The adopted level densities (LD) for the nuclei produced through different reaction mechanisms significantly impact the accurate calculation of cross sections for the different reaction channels. Many common LD models make simplified assumptions regarding the overall behavior of the total LD and the intrinsic spin and parity distributions of the excited states. However, very few experimental constraints are taken into account in these models: LD at neutron separation energy coming from average spacings of s- and p-wave resonances ( D 0 and D 1 , respectively) whenever they have been previously measured, and the sometimes subjective extrapolation of discrete levels. These, however, constrain the LD only in very specific regions of excitation energy, and for specific spins and parities. This work aims to establish additional experimental constraints on LD through quantitative correlations between cross sections and LD. This allows for fitting and the determination of detailed structures in LD. For this we use the microscopic Hartree-Fock-Bogoliubov (HFB) LD as a starting point as the HFB LD provide a more realistic spin and parity distributions than phenomenological models such as Gilbert-Cameron (GC). We then associate variations predicted by the HFB model with the structure observed in double-differential cross sections at low outgoing neutron energy, a region that is dominated by the LD input. We also use (n, p) on 56 Fe , as an example case where angle-integrated cross sections are extremely sensitive to LD. For comparison purposes we also perform calculations with the GC model. With this approach we are able to perform fits of the LD based on actual experimental data, constraining the model and ensuring its consistency. This approach can be particularly useful in extrapolating the LD to nuclei for which high-excited discrete levels and/or values of D 0 or D 1 are unknown. Finally, it also predicts neutron-induced inelastic γ cross sections that in some cases can differ significantly from more standard phenomenological LD models such as GC.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

The epsilon Geminorum occultation - Evidence for waves or turbulence

Intercomparison of occultation data from various observatories shows poor correlation of the raw data but apparent correlations in the derived temperature profiles, as discussed in a paper by French and Elliott. We point out that the data are at least as consistent with Martian scintillation as they are with a semiglobal wave model.

Hubbard, W. B.↗

Experimental and Analytical Investigation of the Coolant Flow Characteristics in Cooled Turbine Airfoils

The flow characteristics of turbine airfoil cooling system components were experimentally investigated. Flow models representative of leading edge impingement, impingement with crossflow (midchord cooling), pin fins, feeder supply tube, and a composite model of a complete airfoil flow system were tested. Test conditions were set by varying pressure level to cover the Mach number and Reynolds number range of interest in advanced turbine applications. Selected geometrical variations were studied on each component model to determine these effects. Results of these tests were correlated and compared with data available in the literature. Orifice flow was correlated in terms of discharge coefficients. For the leading edge model this was found to be a weak function of hole Mach number and orifice-to-impinged wall spacing. In the impingement with crossflow tests, the discharge coefficient was found to be constant and thus independent of orifice Mach number, Reynolds number, crossflow rate, and impingement geometry. Crossflow channel pressure drop showed reasonable agreement with a simple one-dimensional momentum balance. Feeder tube orifice discharge coefficients correlated as a function of orifice Mach number and the ratio of the orifice-to-approach velocity heads. Pin fin data was correlated in terms of equivalent friction factor, which was found to be a function of Reynolds number and pin spacing but independent of pin height in the range tested.

Damerow, W. P.↗

Radiation Transport Modeling and Assessment to Better Predict Radiation Exposure, Dose, and Toxicological Effects to Human Organs on Long Duration Space Flights

NASA's long-range plans include possible human exploratory missions to the moon and Mars within the next quarter century. Such missions beyond low Earth orbit will expose crews to transient radiation from solar particle events which include high-energy galactic cosmic rays and high-energy protons. Because the radiation levels in space are high and the missions long, adequate shielding is needed to minimize the deleterious health effects of exposure to radiation. The focus of this study is radiation exposure to the blood-forming organs of the NASA astronauts. NASA/JSC developed the Phantom Torso Experiment for Organ Dose Measurements which housed active and passive dosimeters that would monitor and record absorbed radiation levels at vital organ locations. This experiment was conducted during the STS-9 I mission in May '98 and provided the necessary space radiation data for correlation to results obtained from the current analytical models used to predict exposure to the blood-forming organs. Numerous models (i.e., BRYNTRN and HZETRN) have been developed and used to predict radiation exposure. However, new models are continually being developed and evaluated. The Space Environment Information Systems (SPENVIS) modeling program, developed by the Belgian Institute for Space Aeronomy, is to be used and evaluated as a part of the research activity. It is the intent of this research effort to compare the modeled data to the findings from the STS-9 I mission; assess the accuracy and efficiency of this model; and to determine its usefulness for predicting radiation exposure and developing better guidelines for shielding requirements for long duration manned missions.

Denkins, Pamela↗

Measurement of breast tissue composition with dual energy cone-beam computed tomography: A postmortem study

Purpose: To investigate the feasibility of a three-material compositional measurement of water, lipid, and protein content of breast tissue with dual kVp cone-beam computed tomography (CT) for diagnostic purposes. Methods: Simulations were performed on a flat panel-based computed tomography system with a dual kVp technique in order to guide the selection of experimental acquisition parameters. The expected errors induced by using the proposed calibration materials were also estimated by simulation. Twenty pairs of postmortem breast samples were imaged with a flat-panel based dual kVp cone-beam CT system, followed by image-based material decomposition using calibration data obtained from a three-material phantom consisting of water, vegetable oil, and polyoxymethylene plastic. The tissue samples were then chemically decomposed into their respective water, lipid, and protein contents after imaging to allow direct comparison with data from dual energy decomposition. Results: Guided by results from simulation, the beam energies for the dual kVp cone-beam CT system were selected to be 50 and 120 kVp with the mean glandular dose divided equally between each exposure. The simulation also suggested that the use of polyoxymethylene as the calibration material for the measurement of pure protein may introduce an error of -11.0%. However, the tissue decomposition experiments, which employed a calibration phantom made out of water, oil, and polyoxymethylene, exhibited strong correlation with data from the chemical analysis. The average root-mean-square percentage error for water, lipid, and protein contents was 3.58% as compared with chemical analysis. Conclusions: The results of this study suggest that the water, lipid, and protein contents can be accurately measured using dual kVp cone-beam CT. The tissue compositional information may improve the sensitivity and specificity for breast cancer diagnosis.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Bias corrections of GOSAT SWIR XCO 2 and XCH 4 with TCCON data and their evaluation using aircraft measurement data

We describe a method for removing systematic biases of column-averaged dry air mole fractions of CO 2 (XCO 2 ) and CH 4 (XCH 4 ) derived from short-wavelength infrared (SWIR) spectra of the Greenhouse gases Observing SATellite (GOSAT). We conduct correlation analyses between the GOSAT biases and simultaneously retrieved auxiliary parameters. We use these correlations to bias correct the GOSAT data, removing these spurious correlations. Data from the Total Carbon Column Observing Network (TCCON) were used as reference values for this regression analysis. To evaluate the effectiveness of this correction method, the uncorrected/corrected GOSAT data were compared to independent XCO 2 and XCH 4 data derived from aircraft measurements taken for the Comprehensive Observation Network for TRace gases by AIrLiner (CONTRAIL) project, the National Oceanic and Atmospheric Administration (NOAA), the US Department of Energy (DOE), the National Institute for Environmental Studies (NIES), the Japan Meteorological Agency (JMA), the HIAPER Pole-to-Pole observations (HIPPO) program, and the GOSAT validation aircraft observation campaign over Japan. These comparisons demonstrate that the empirically derived bias correction improves the agreement between GOSAT XCO 2 /XCH 4 and the aircraft data. Finally, we present spatial distributions and temporal variations of the derived GOSAT biases.

54 ENVIRONMENTAL SCIENCES↗

Machine learning etudes in astrophysics: selection functions for mock cluster catalogs

Making mock simulated catalogs is an important component of astrophysical data analysis. Selection criteria for observed astronomical objects are often too complicated to be derived from first principles. However the existence of an observed group of objects is a well-suited problem for machine learning classification. In this paper we use one-class classifiers to learn the properties of an observed catalog of clusters of galaxies from ROSAT and to pick clusters from mock simulations that resemble the observed ROSAT catalog. We show how this method can be used to study the cross-correlations of thermal Sunya'ev-Zeldovich signals with number density maps of X-ray selected cluster catalogs. The method reduces the bias due to hand-tuning the selection function and is readily scalable to large catalogs with a high-dimensional space of astrophysical features.

79 ASTRONOMY AND ASTROPHYSICS↗

Proceedings of the First Aerospace Mechanisms Symposium

To provide a better opportunity, therefore, for the aerospace mechanisms designer to compare and correlate the specific knowledge gained from a wide variety of important mechanism design efforts, the First Aerospace Mechanisms Symposium was held on 19-20 May 1966. This Symposium, dealing exclusively with aerospace mechanism design and development, was sponsored by the Jet Propulsion Laboratory of the California Institute of Technology, Lockheed Missiles & Space Company, and the University of Santa Clara. The first aerospace symposium with such broad sponsorship, is supplied the first forum for an extensive discussion in depth of ideas, problems, and accomplishments regarding aerospace mechanisms. It stressed the practical aspects, with emphasis on actual flight test data and correlation with analytical predictions. This volume presents the papers offered at the Symposium in order to provide the aerospace mechanisms designer with a useful source of ideas and information and to serve as a stimulant to the continuance of a periodic professional interchange in the field of aerospace mechanisms.

Conference↗

Boundary layer transition

The boundary layer stability, its active control by sound and surface heating and the effect of curvature are studied numerically and experimentally for subsonic flow. In addition, the experimental and flight test data are correlated using the stability theory for supersonic Mach numbers. Active transition fixing and feedback control of boundary layer by sound interactions are experimentally investigated at low speed over an airfoil. Numerical simulation of active control by surface heating and cooling in air shows that by appropriate phase adjustment a reduction in the level of perturbation can be obtained. This simulation is based on the solution of two-dimensional compressible Navier-Stokes equations for a flat plate. Goertler vortices are studied experimentally on an airfoil in the Low Turbulence Pressure Tunnel (LTPT). The flow pattern was visualized using the sublimating chemical technique and data were obtained using a three component laser velocimeter. The effect of curvature on swept leading-edge stability on a cylinder was numerically studied. The results suggest that transition is dominated by traveling disturbance waves and that the waves with the greatest total amplification has an amplitude ratio of e sup 11. Experimental data from the quiet supersonic tunnel and flight tests are analyzed using linear compressible stability theory.

Maestrello, L.↗

Comparison of Calculated and Experimental Temperatures and Coolant Pressure Losses for a Cascade of Small Air-Cooled Turbine Rotor Blades

Average spanwise blade temperatures and cooling-air pressure losses through a small (1.4-in, span, 0.7-in, chord) air-cooled turbine blade were calculated and are compared with experimental nonrotating cascade data. Two methods of calculating the blade spanwise metal temperature distributions are presented. The method which considered the effect of the length-to-diameter ratio of the coolant passage on the blade-to-coolant heat-transfer coefficient and assumed constant coolant properties based on the coolant bulk temperature gave the best agreement with experimental data. The agreement obtained was within 3 percent at the midspan and tip regions of the blade. At the root region of the blade, the agreement was within 3 percent for coolant flows within the turbulent flow regime and within 10 percent for coolant flows in the laminar regime. The calculated and measured cooling-air pressure losses through the blade agreed within 5 percent. Calculated spanwise blade temperatures for assumed turboprop engine operating conditions of 2000 F turbine-inlet gas temperature and flight conditions of 300 knots at a 30,000-foot altitude agreed well with those obtained by the extrapolation of correlated experimental data of a static cascade investigation of these blades.

Stepka, Francis S↗

Response to Comment on "Does the Earth Have an Adaptive Infrared Iris?"

In his comment on Lindzen et al., Harrison found that the amount of high-level clouds, A, and the sea-surface temperature beneath clouds, T, averaged over a large oceanic domain in the western Pacific have secular linear trends of opposite signs over a period of 20 months. He found that when the linear trends are subtracted from the data, the correlation between the residual A and T is much reduced. His estimates of the confidence levels for the correlation indicate, moreover, that this correlation is not statistically significant. The domain-averaged A and, to a lesser degree, T, have distinct intra-seasonal and seasonal variations. These variations are influenced by the large-scale wind and temperature distributions and by the seasonal variation of insolation. To separate the local effect from the effect of slowly changing large-scale conditions, rather than subtracting 20-month linear trends from the series, which has the potential to spuriously extrapolate intra-seasonal and seasonal variations to even longer time scales, we subtracted 30-day running means of A and T from each time series; in effect, the data were high-pass filtered. The number of points (days), N, is reduced by this process from the original value of 510 to 480.

Bell, Thomas L.↗

Isotopic Constraints on the Genesis of Carbonates in Martian Meteorite ALH 84001

Oxygen isotopic analyses in approximately 20 micrometer spots in a chemically diverse suite of carbonates from ALH 84001 show highly variable delta(exp 18)O values from +5.4 to +25.3%. The isotopic data are correlated with the major element composition of the carbonate. The earliest forming (Ca-rich) carbonates have the lowest delta(exp 18)O values and the late-forming Mg-rich carbonates have the highest delta(exp 18)O values. Two models that can explain the isotopic variation were investigated. The carbonates could have formed in a water-rich environment at relatively low, but highly variable temperatures. In this open-system case the lower limit to the temperature variation is approximately 125 C, with fluctuations of over 250 C possible within the constraints of the model, depending on fluid composition. Alternatively the data can be explained by a closed-system model in which carbonates precipitated from a limited amount of a CO2-rich fluid. This scenario can reproduce the range of isotopic values observed, even at relatively high temperatures (greater than 500 C). Thus, the oxygen isotopic compositions do not provide unequivocal evidence for formation of the carbonates at low temperature. Neither of these scenarios is consistent with a biological origin of the carbonates and their associated features. Olivine from ALH 84001 occurs as clusters within orthopyroxene adjacent to fractures containing disrupted carbonate globules and feldspathic shock glass. The inclusions are irregular in shape and range in size from approximately 40 micrometers to submicrometer. The olivine exhibits a limited range of chemical composition from Fo(sub 65) to Fo(sub 66). We measured delta(exp 18)O values of the olivine to be +5.1 +/- 1.4%, indistinguishable within uncertainty from the host orthopyroxene. The data suggest that the olivine formed at high temperature (greater than 800 C), and is probably unrelated to carbonate formation. Instead the olivine probably formed by metamorphic reactions involving either dehydration of hydrous silicates or reduction of opx + spinel. If the reactions took place after carbonate formation, they could have caused devolatilization of siderite, producing the magnetite in the ALH carbonate globules. This scenario is also inconsistent with a biological origin for the features in ALH 84001.

Leshin, Laurie A.↗