Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PHYSICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Identification of combustion mode under MILD conditions using Chemical Explosive Mode Analysis

Direct Numerical Simulations (DNS) data of Moderate or Intense Low-oxygen Dilution (MILD) combustion are analysed in this paper to identify the contributions of the autoignition and flame modes. This is performed using an extended Chemical Explosive Mode Analysis (CEMA) which accounts for diffusion effects allowing it to discriminate between deflagration and autoignition. This analysis indicates that in premixed MILD combustion conditions, the main combustion mode is ignition for all dilution and turbulence levels and for the two reactant temperature conditions considered. In non-premixed conditions, the preponderance of the ignition mode was observed to depend on the axial location and mixture fraction stratification. With a large mixture fraction lengthscale, ignition is more preponderant in the early part of the domain while the deflagrative mode increases further downstream. On the other hand, when the mixture fraction lengthscale is small, sequential autoignition is observed. Finally, the various combustion modes are observed to correlate strongly with mixture fraction where lean mixtures are more likely to autoignite while stoichiometric and rich mixtures are more likely to react as deflagrative structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High Energy Ion Beam Combustion Of TiO{sub 2}-B-Al Mixture

High energy ion beam of a plasma focus device was used to combust TiO{sub 2}-B-Al powder mixture under quasi-adiabatic conditions. Despite uncompleted propagation of combustion wave through the sample, the microstructure of the product was completely different from that obtained from conventional bulk heating in furnace. Combustion reaction of the mixture in furnace at 700 deg. C resulted in spiral-helix motion, while plasma synthesis of the same mixture resulted in uniform self-sustaining wave propagation.

36 MATERIALS SCIENCE↗

Measurements of gas parameters in plasma-assisted supersonic combustion processes using diode laser spectroscopy

We report a procedure for temperature and water vapour concentration measurements in an unsteady-state combustion zone using diode laser absorption spectroscopy. The procedure involves measurements of the absorption spectrum of water molecules around 1.39 {mu}m. It has been used to determine hydrogen combustion parameters in M = 2 gas flows in the test section of a supersonic wind tunnel. The relatively high intensities of the absorption lines used have enabled direct absorption measurements. We describe a differential technique for measurements of transient absorption spectra, the procedure we used for primary data processing and approaches for determining the gas temperature and H{sub 2}O concentration in the probed zone. The measured absorption spectra are fitted with spectra simulated using parameters from spectroscopic databases. The combustion-time-averaged ({approx}50 ms) gas temperature and water vapour partial pressure in the hot wake region are determined to be 1050 K and 21 Torr, respectively. The large signal-to-noise ratio in our measurements allowed us to assess the temporal behaviour of these parameters. The accuracy in our temperature measurements in the probed zone is {approx}40 K. (laser applications and other topics in quantum electronics)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Improving lithium-ion battery performances by adding fly ash from coal combustion on cathode film

A lithium battery is composed of anode, cathode and a separator. The performance of lithium battery is also influenced by the conductive material of cathode film. In this research, the use of fly ash from coal combustion as conductive enhancer for increasing the performances of lithium battery was investigated. Lithium iron phosphate (LiFePO{sub 4}) was used as the active material of cathode. The dry fly ash passed through 200 mesh screen, LiFePO{sub 4} and acethylene black (AB), polyvinylidene fluoride (PVDF) as a binder and N-methyl-2-pyrrolidone (NMP) as a solvent were mixed to form slurry. The slurry was then coated, dried and hot pressed to obtain the cathode film. The ratio of fly ash and AB were varied at the values of 1%, 2%, 3%, 4% and 5% while the other components were at constant. The anode film was casted with certain thickness and composition. The performance of battery lithium was examined by Eight Channel Battery Analyzer, the composition of the cathode film was examined by XRD (X-Ray Diffraction), and the structure and morphology of the anode film was analyzed by SEM (Scanning Electron Microscope). The composition, structure and morphology of cathode film was only different when fly ash added was 4% of AB or more. The addition of 2% of AB on cathode film gave the best performance of 81.712 mAh/g on charging and 79.412 mAh/g on discharging.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Assessing the relative importance of flame regimes in Raman/Rayleigh line measurements of turbulent lifted flames

Understanding and quantifying the relative importance of premixed and non-premixed reaction zones within turbulent partially premixed flames is an important issue for multi-regime combustion. The recently-developed method of gradient-free regime identification (GFRI) is applied to instantaneous 1D Raman/Rayleigh measurements of temperature and major species from two turbulent lifted methane/air flames. Local premixed and non-premixed reaction zones are identified using criteria based on the mixture fraction, the chemical explosive mode, and the heat release rate, the latter two being calculated from an approximation of the full thermochemical state of each measured sample. A chemical mode (CM) zero-crossing is a previously documented marker for a premixed reaction zone. Results from the lifted flames show strong correlations among the mixture fraction at the CM zero-crossing, the magnitude of the change in CM at the zero-crossing, and the local heat release rate at the CM zero-crossing compared to the maximum heat release rate. The trends are confirmed through a comparable analysis of numerical simulations of two laminar triple flames. These newly documented trends are associated with the transition from dominantly premixed flame structures to dominantly non-premixed flames structures. The methods introduced for assessing the relative importance of local premixed and non-premixed reactions zones have potential for application to a broad range of turbulent flames.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facile synthesis of highly active reduced graphene oxide-CuI catalyst through a simple combustion method for photocatalytic reduction of CO{sub 2} to methanol

We report a facile combustion method synthesis of reduced graphene oxide/CuI composites as a photocatalyst, in which CuI nanoparticles were homogeneously distributed on the surface of reduced graphene oxide (rGO), showing a good visible light response. The rGO-supported and unsupported CuI hybrids were tested over the photocatalytic reduction of CO{sub 2} for methanol evolution in visible light. In the current study rGO-CuI composites have shown excellent yields (19.91 μmol g-cat{sup −1}). rGO provides a light-weight, charge complementary and two-dimensional material that interacts effectively with the CuI nanoparticles. - Graphical abstract: A facile reduced graphene oxide(rGO)/ CuI nanoparticles complexes hybrid material was prepared by a naked flame. This method can be simple and rapid preparation of composite materials which exhibit excellent catalytic performance. It is not only can improve the light absorption but also can be highly efficient reduction of CO{sub 2} to methanol in visible light. So the rGO-CuI composite will find potential applications as catalysts in organic photosynthetic reaction. Display Omitted - Highlights: • Reduced graphene oxide-CuI composites have been prepared by a facile method. • This method can produce reduced graphene oxide from graphene oxide without any reducing agent. • The absorption efficiency of rGO-CuI composites is significantly higher than rGO and CuI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Co-optima fuels combustion: A comprehensive experimental investigation of prenol isomers

Carbon monoxide time-histories, ignition delay times, and laminar burning velocity measurements are reported for the oxidation of 3-methyl-2-buten-1-ol (prenol) and 3-methyl-3-buten-1-ol (isoprenol). These prenols are fuel candidates outlined by the U.S. Department of Energy’s Co-Optimization of Fuels and Engines (Co-Optima) program. The laminar burning velocity measurements were conducted for two fuels with synthetic air within a constant-volume spherical combustion chamber at initial conditions of 428 K and 1 atm for a range of equivalence ratios from 0.75 to 1.50. The laminar burning velocities of the two fuels were found to be similar, and the maximum value occurred at an equivalence ratio near 1.0. Carbon monoxide time-histories and ignition delay times were recorded behind reflected shockwaves in a double-diaphragm, heated shock tube over the temperature range 1269–1472 K near 9.4 atm with a mixture of 0.05% fuel/0.35% O 2 /99.6% Ar. Comparisons with predictions of a detailed chemical kinetic mechanism from the literature were provided. Current model predictions overpredicted both the ignition delay time and the max CO yield; however, the model captured the profile of CO formation well. Detailed uncertainty and sensitivity analyses were carried out to identify important reactions that need attention for accurate prediction of these fuel’s chemistry. Further investigation into the rate of C 3 H 3 + O 2 = CH 2 CO + HCO reaction was suggested based on current experiments. In conclusion, the experimental data and analysis presented here is critical in the development, validation and improvement of kinetic models of these promising Co-Optima fuels.

09 BIOMASS FUELS↗

Large eddy simulation of soot formation in a turbulent non-premixed jet flame

A recently developed subgrid model for soot dynamics [H. El-Asrag, T. Lu, C.K. Law, S. Menon, Combust. Flame 150 (2007) 108-126] is used to study the soot formation in a non-premixed turbulent flame. The model allows coupling between reaction, diffusion and soot (including soot diffusion and thermophoretic forces) processes in the subgrid domain without requiring ad hoc filtering or model parameter adjustments. The combined model includes the entire process, from the initial phase, when the soot nucleus diameter is much smaller than the mean free path, to the final phase, after coagulation and aggregation, where it can be considered in the continuum regime. A relatively detailed but reduced kinetics for ethylene-air is used to simulate an experimentally studied non-premixed ethylene/air jet diffusion flame. Acetylene is used as a soot precursor species. The soot volume fraction order of magnitude, the location of its maxima, and the soot particle size distribution are all captured reasonably. Along the centerline, an initial region dominated by nucleation and surface growth is established followed by an oxidation region. The diffusion effect is found to be most important in the nucleation regime, while the thermophoretic forces become more influential downstream of the potential core in the oxidation zone. The particle size distribution shows a log-normal distribution in the nucleation region, and a more Gaussian like distribution further downstream. Limitations of the current approach and possible solution strategies are also discussed. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical Kinetic Modeling of Hydrogen Combustion Limits

A detailed chemical kinetic model is used to explore the flammability and detonability of hydrogen mixtures. In the case of flammability, a detailed chemical kinetic mechanism for hydrogen is coupled to the CHEMKIN Premix code to compute premixed, laminar flame speeds. The detailed chemical kinetic model reproduces flame speeds in the literature over a range of equivalence ratios, pressures and reactant temperatures. A series of calculation were performed to assess the key parameters determining the flammability of hydrogen mixtures. Increased reactant temperature was found to greatly increase the flame speed and the flammability of the mixture. The effect of added diluents was assessed. Addition of water and carbon dioxide were found to reduce the flame speed and thus the flammability of a hydrogen mixture approximately equally well and much more than the addition of nitrogen. The detailed chemical kinetic model was used to explore the detonability of hydrogen mixtures. A Zeldovich-von Neumann-Doring (ZND) detonation model coupled with detailed chemical kinetics was used to model the detonation. The effectiveness on different diluents was assessed in reducing the detonability of a hydrogen mixture. Carbon dioxide was found to be most effective in reducing the detonability followed by water and nitrogen. The chemical action of chemical inhibitors on reducing the flammability of hydrogen mixtures is discussed. Bromine and organophosphorus inhibitors act through catalytic cycles that recombine H and OH radicals in the flame. The reduction in H and OH radicals reduces chain branching in the flame through the H + O{sub 2} = OH + O chain branching reaction. The reduction in chain branching and radical production reduces the flame speed and thus the flammability of the hydrogen mixture.

08 HYDROGEN↗

Development of NiO-Nanocarbon and MnO{sub 2}-Nanocarbon Energetic Catalytic Electrode Materials to Synthesize Electrical Energy through Electrochemical Oxidation of Glucose

Automobile and transportation on land and in air are the major causes of global environment pollution through the chemical combustion of petroleum fuels. The need of the hour is to run the transportation units by fuel cells which convert fuels to energy through electrochemical oxidation, straight to pure electrical energy with no polluting substances. Development of fuel cell lies on exhaustive research on development of high energetic electrocatalytic electrodes over which the fuels break to produce free electron and ions, delivering electrical energy. The present work aims at developing two electrocatalytic materials: NiO-nanocarbon and MnO{sub 2}-nanocarbon by electrosynthesis method. The performance of the materials was investigated by electrochemical characterization: cyclic voltammetry, chronoammetry, polarization tests and impedance spectroscopy. The materials were found to deliver a high current on electro-oxidation of glucose. The effect of nanocarbon on NiO and MnO{sub 2} has enhanced the current to a level of over 100 mA/cm{sup 2}. XRD study showed the presence of metal oxides and carbon. The electron microscopy images revealed fine grain oxides with entrapped nanocarbon. The carbon seems to be in the form of graphene, produced during electrochemical exfoliation at anode. The SEM morphology of enhanced 3D surface area with high energetic nanocarbon phase entrapped with fine structure metal oxides accounts for the high current obtained by electro-oxidation of the fuel. The materials developed are found to be very good energetic electrodes for future fuel cell in automotive industry.

36 MATERIALS SCIENCE↗

Radiation intensity of lignite-fired oxy-fuel flames

The radiative heat transfer in oxy-fuel flames is compared to corresponding conditions in air-fuel flames during combustion of lignite in the Chalmers 100 kW oxy-fuel test facility. In the oxy-fuel cases the flue-gas recycle rate was varied, so that, in principle, the same stoichiometry was kept in all cases, whereas the oxygen fraction in the recycled flue-gas mixture ranged from 25 to 29 vol.%. Radial profiles of gas concentration, temperature and total radiation intensity were measured in the furnace. The temperature, and thereby the total radiation intensity of the oxy-fuel flames, increases with decreasing flue-gas recycle rate. The ratio of gas and total radiation intensities increases under oxy-fuel conditions compared to air-firing. However, when radiation overlap between gas and particles is considered the ratios for air-firing and oxy-fuel conditions become more similar, since the gas-particle overlap is increased in the CO{sub 2}-rich atmosphere. A large fraction of the radiation in these lignite flames is emitted by particles whose radiation was not significantly influenced by oxy-fuel operation. Therefore, an increment of gas radiation due to higher CO{sub 2} concentration is not evident because of the background of particle radiation, and, the total radiation intensities are similar during oxy-fuel and air-fuel operation as long as the temperature distributions are similar. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimal discharge placement in plasma-assisted combustion of a methane jet in cross flow

Repetitively pulsed, nonequilibrium plasma discharges are studied for their ability to ignite and stabilize methane jet flames in cross flow air. The placement of the discharge is surveyed to optimize the flame duty cycle (stability). We find that flame ignition is not achieved when the discharge is located in the potential core region of the fuel jet or on the windward side of the most upstream part of the near field of the jet. A low (but nonzero) duty cycle is seen when the discharge is placed on the leeward side of the upstream near-field region. A high duty cycle (up to unity) is seen for discharge placement on both the leeward and windward sides of the downstream part of the near field. These results confirm that the effectiveness of the nonequilibrium discharge in stabilizing this flame depends on its placement in the complex scalar and velocity field. The mixture fraction at the discharge placement is characterized by plasma-induced breakdown spectroscopy (PIBS). The ratio of emission intensity of the CN band at 388 nm to the N{sub 2} band at 337 nm is used to map the local equivalence ratio in the flow. We find that the methane mixture fraction at optimal discharge placements is lower than that where the flame resides in non-discharge-stabilized diffusion flames and is equal to that found in plasma-assisted methane jets in coflow air. Planar laser-induced fluorescence (PLIF) imaging of CH radicals is carried out to qualitatively understand the structure of the ignition flame kernel. The plasma discharge and flame base are spatially separated, suggesting that the discharge is a steady supplier of reactive species but not an instantaneous flame ignition source. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Combustion characteristics of nanoaluminum, liquid water, and hydrogen peroxide mixtures

An experimental investigation of the combustion characteristics of nanoaluminum (nAl), liquid water (H{sub 2}O{sub (l)}), and hydrogen peroxide (H{sub 2}O{sub 2}) mixtures has been conducted. Linear and mass-burning rates as functions of pressure, equivalence ratio ({phi}), and concentration of H{sub 2}O{sub 2} in H{sub 2}O{sub (l)} oxidizing solution are reported. Steady-state burning rates were obtained at room temperature using a windowed pressure vessel over an initial pressure range of 0.24 to 12.4 MPa in argon, using average nAl particle diameters of 38 nm, {phi} from 0.5 to 1.3, and H{sub 2}O{sub 2} concentrations between 0 and 32% by mass. At a nominal pressure of 3.65 MPa, under stoichiometric conditions, mass-burning rates per unit area ranged between 6.93 g/cm{sup 2} s (0% H{sub 2}O{sub 2}) and 37.04 g/cm{sup 2} s (32% H{sub 2}O{sub 2}), which corresponded to linear burning rates of 9.58 and 58.2 cm/s, respectively. Burning rate pressure exponents of 0.44 and 0.38 were found for stoichiometric mixtures at room temperature containing 10 and 25% H{sub 2}O{sub 2}, respectively, up to 5 MPa. Burning rates are reduced above {proportional_to}5 MPa due to the pressurization of interstitial spaces of the packed reactant mixture with argon gas, diluting the fuel and oxidizer mixture. Mass burning rates were not measured above {proportional_to}32% H{sub 2}O{sub 2} due to an anomalous burning phenomena, which caused overpressurization within the quartz sample holder, leading to tube rupture. High-speed imaging displayed fingering or jetting ahead of the normal flame front. Localized pressure measurements were taken along the sample length, determining that the combustion process proceeded as a normal deflagration prior to tube rupture, without significant pressure buildup within the tube. In addition to burning rates, chemical efficiencies of the combustion reaction were determined to be within approximately 10% of the theoretical maximum under all conditions studied. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Systematic Structure–Property Relationship Studies in Palladium-Catalyzed Methane Complete Combustion

To limit further rising levels in methane emissions from stationary and mobile sources and to enable promising technologies based on methane, the development of efficient combustion catalysts that completely oxidize CH 4 to CO 2 and H 2 O at low temperatures in the presence of high steam concentrations is required. Palladium is widely considered as one of the most promising materials for this reaction, and a better understanding of the factors affecting its activity and stability is crucial to design even more improved catalysts that efficiently utilize this precious metal. Here we report a study of the effect of three important variables (particle size, support, and reaction conditions including water) on the activity of supported Pd catalysts. We use uniform palladium nanocrystals as catalyst precursors to prepare a library of well-defined catalysts to systematically describe structure–property relationships with help from theory and in situ X-ray absorption spectroscopy. With this approach, we confirm that PdO is the most active phase and that small differences in reaction rates as a function of size are likely due to variations in the surface crystal structure. We further demonstrate that the support exerts a limited influence on the PdO activity, with inert (SiO 2 ), acidic (Al 2 O 3 ), and redox-active (Ce 0.8 Zr 0.2 O 2 ) supports providing similar rates, while basic (MgO) supports show remarkably lower activity. Finally, we show that the introduction of steam leads to a considerable decrease in rates that is due to coverage effects, rather than structural and/or phase changes. Altogether, the data suggest that to further increase the activity and stability of Pd-based catalysts for methane combustion, increasing the surface area of supported PdO phases while avoiding strong adsorption of water on the catalytic surfaces is required. Furthermore, this study clarifies contrasting reports in the literature about the active phase and stability of Pd-based materials for methane combustion.

36 MATERIALS SCIENCE↗

Tri-metallic ferrite oxygen carriers for chemical looping combustion

The disclosure provides a tri-metallic ferrite oxygen carrier for the chemical looping combustion of carbonaceous fuels. The tri-metallic ferrite oxygen carrier comprises Cu.sub.xFe.sub.yMn.sub.zO.sub.4-.delta., where Cu.sub.xFe.sub.yMn.sub.zO.sub.4-.delta. is a chemical composition. Generally, 0.5.ltoreq.x.ltoreq.2.0, 0.2.ltoreq.y.ltoreq.2.5, and 0.2.ltoreq.z.ltoreq.2.5, and in some embodiments, 0.8.ltoreq.x.ltoreq.1.2, y.ltoreq.1.2, and z.gtoreq.0.8. The tri-metallic ferrite oxygen carrier may be used in various applications for the combustion of carbonaceous fuels, including as an oxygen carrier for chemical looping combustion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental and computational investigations of ethane and ethylene kinetics with copper oxide particles for Chemical Looping Combustion

In this work, reaction pathways for the oxidation of methane, ethane, and ethylene with CuO was obtained by ReaxFF Molecular Dynamics (MD) simulations between temperatures of 1000 K and 2000 K. Experiments in a fixed-bed flow reactor were preformed with methane, ethane, and ethylene at temperatures ranging from 500 K to 1000 K with time-dependent species measurements from an Electron-Ionization Molecular Beam Mass Spectrometer (MBMS), and species validation with Gas Chromatography (GC) for detection of complete and intermediate combustion products. The MBMS and GC allow for the detection of oxygenated species and larger species produced from radical reformation. The simulation and experiment agree on the production of such species as CH 3 CHO, CH 2 O, CO, and H 2 O, which allow for the creation of simple C1 and C2 reaction pathways, which can be used in kinetic models of C2 species and larger fuels such as biofuels, which inherently depend on C1 and C2 kinetics and reaction pathway. The simulation and experiment disagree on the formation of C 2 H 2 , CH 3 OH, and CO 2 with large amounts of C 2 H 2 being measured in the ethylene oxidation simulations and CH 3 OH being formed in methane oxidation simulations, while neither species were experimentally found. In the case of CO 2 large amounts of CO 2 are rapidly produced in experiments with C2 fuels at 800 K, while little-to-no CO 2 was observed in simulations. This is believed to be resulting from the extremely short timescale of the simulations, preventing total oxidation of the fuel. Here, the differences in products produced between simulation and experiment allow for the potential to modify the ReaxFF potential functions to more accurately model the experimental products of Cu–H–O–C reaction kinetics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Control of Combustion-Instabilities Through Various Passive Devices

It is well known that under some operating conditions, rocket engines (using solid or liquid fuels) exhibit unstable modes of operation that can lead to engine malfunction and shutdown. The sources of these instabilities are diverse and are dependent on fuel, chamber geometry and various upstream sources such as pumps, valves and injection mechanism. It is believed that combustion-acoustic instabilities occur when the acoustic energy increase due to the unsteady heat release of the flame is greater than the losses of acoustic energy from the system [1, 2]. Giammar and Putnam [3] performed a comprehensive study of noise generated by gasfired industrial burners and made several key observations; flow noise was sometimes more intense than combustion roar, which tended to have a characteristic frequency spectrum. Turbulence was amplified by the flame. The noise power varied directly with combustion intensity and also with the product of pressure drop and heat release rate. Karchmer [4] correlated the noise emitted from a turbofan jet engine with that in the combustion chamber. This is important, since it quantified how much of the noise from an engine originates in the combustor. A physical interpretation of the interchange of energy between sound waves and unsteady heat release rates was given by Rayleigh [5] for inviscid, linear perturbations. Bloxidge et al [6] extended Rayleigh s criterion to describe the interaction of unsteady combustion with one-dimensional acoustic waves in a duct. Solutions to the mass, momentum and energy conservation equations in the pre- and post-flame zones were matched by making several assumptions about the combustion process. They concluded that changes in boundary conditions affect the energy balance of acoustic waves in the combustor. Abouseif et al [7] also solved the one-dimensional flow equations, but they used a onestep reaction to evaluate the unsteady heat release rate by relating it to temperature and velocity perturbations. Their analysis showed that oscillations arise from coupling between entropy waves produced at the flame and pressure waves originating from the nozzle. Yang and Culick [8] assumed a thin flame sheet, which is distorted by velocity and pressure oscillations. Conservation equations were expressed in integral form and solutions for the acoustic wave equations and complex frequencies were obtained. The imaginary part of the frequency indicated stability regions of the flame. Activation energy asymptotics together with a one-step reaction were used by McIntosh [9] to study the effects of acoustic forcing and feedback on unsteady, one-dimensional flames. He found that the flame stability was altered by the upstream acoustic feedback. Shyy et al [10] used a high-accuracy TVD scheme to simulate unsteady, one-dimensional longitudinal, combustion instabilities. However, numerical diffusion was not completely eliminated. Recently, Prasad [11] investigated numerically the interactions of pressure perturbations with premixed flames. He used complex chemistry to study responses of pressure perturbations in one-dimensional combustors. His results indicated that reflected and transmitted waves differed significantly from incident waves.

Frendi, Kader↗

Reactive jet and cyclonic attrition analysis of ilmenite in chemical looping combustion systems

In chemical looping combustion (CLC), the chosen oxygen carrier’s (OC) reactivity maintenance and attrition propensity play key roles in determining its lifetime in such systems. Jet and cyclonic attrition are two main mechanisms of attrition in CLC systems, which typically use fluidized beds and cyclones. In contrast to standardized tests, that assess attrition characteristics under ambient and non-reacting conditions, a realistic evaluation must include the behavior under relevant high temperatures and cyclic oxidation-reduction. In this study, separate jet and cyclonic attrition test units were constructed to investigate the effects of temperature, fuel gas concentration and velocity on the performance of ilmenite, a natural ore-based OC in CLC. Testing showed that thermal and chemical effects were crucial to accurately determine the performance of ilmenite. For experiments conducted between 820°C and 970°C, the intermediate temperature of 895°C provided the best balance between high reactivity and material durability. Additionally, fuel gas concentration affected particle morphology evolution. Iron migration to the surface of the ilmenite particle was enhanced at higher fuel gas concentrations and resulted in reduced attrition rate, presumably due to sintering of the more highly reduced enriched iron phase on the particle surface. The laboratory jet and cyclonic attrition evaluation test units tested in this study can be used to investigate multiple parameters relevant for OC performance, including the degree of reduction, oxygen carrying capacity, attrition resistance, agglomeration, and optimum material operability conditions, as well as to extrapolate test data to determine OC replacement costs in a commercial CLC system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗