Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BURNING PROCESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

The Influence of the 2006 Indonesian Biomass Burning Aerosols on Tropical Dynamics Studied with the GEOS-5 AGCM

The direct and semi-direct effects of aerosols produced by Indonesian biomass burning (BB) during August November 2006 on tropical dynamics have been examined using NASA's Goddard Earth Observing System, Version 5 (GEOS-5) atmospheric general circulation model (AGCM). The AGCM includes CO, which is transported by resolved and sub-grid processes and subject to a linearized chemical loss rate. Simulations were driven by two sets of aerosol forcing fields calculated offline, one that included Indonesian BB aerosol emissions and one that did not. In order to separate the influence of the aerosols from internal model variability, the means of two ten-member ensembles were compared. Diabatic heating from BB aerosols increased temperatures over Indonesia between 150 and 400 hPa. The higher temperatures resulted in strong increases in upward grid-scale vertical motion, which increased water vapor and CO over Indonesia. In October, the largest increases in water vapor were found in the mid-troposphere (~25%) while the largest increases in CO occurred just below the tropopause (80 ppbv or ~50%). Diabatic heating from the Indonesian BB aerosols caused CO to increase by 9% throughout the tropical tropopause layer in November and 5% in the lower stratosphere in December. The results demonstrate that aerosol heating plays an important role in the transport of BB pollution and troposphere-to-stratosphere transport. Changes in vertical motion and cloudiness induced by aerosol heating can also alter the transport and phase of water vapor in the upper troposphere/lower stratosphere.

Ott, Lesley↗
NASA NTRS2015

NASA's Aeroacoustic Tools and Methods for Analysis of Aircraft Noise

Aircraft community noise is a significant concern due to continued growth in air traffic, increasingly stringent environmental goals, and operational limitations imposed by airport authorities. The ability to quantify aircraft noise at the source and ultimately at observers is required to develop low noise aircraft designs and flight procedures. Predicting noise at the source, accounting for scattering and propagation through the atmosphere to the observer, and assessing the perception and impact on a community requires physics-based aeroacoustics tools. Along with the analyses for aero-performance, weights and fuel burn, these tools can provide the acoustic component for aircraft MDAO (Multidisciplinary Design Analysis and Optimization). Over the last decade significant progress has been made in advancing the aeroacoustic tools such that acoustic analyses can now be performed during the design process. One major and enabling advance has been the development of the system noise framework known as Aircraft NOise Prediction Program2 (ANOPP2). ANOPP2 is NASA's aeroacoustic toolset and is designed to facilitate the combination of acoustic approaches of varying fidelity for the analysis of noise from conventional and unconventional aircraft. The toolset includes a framework that integrates noise prediction and propagation methods into a unified system for use within general aircraft analysis software. This includes acoustic analyses, signal processing and interfaces that allow for the assessment of perception of noise on a community. ANOPP2's capability to incorporate medium fidelity shielding predictions and wind tunnel experiments into a design environment is presented. An assessment of noise from a conventional and Hybrid Wing Body (HWB) aircraft using medium fidelity scattering methods combined with noise measurements from a model-scale HWB recently placed in NASA's 14x22 wind tunnel are presented. The results are in the form of community noise metrics and auralizations.

Rizzi, Stephen A.↗
NASA NTRS2021

Potential of Full-polarimetric P- and L-band Sar Data in Characterizing Post-fire Recovery of Arctic Tundra

We used the airborne full polarimetric L-band and P-band SAR (PolSAR) data collected from recent NASA ABoVE Arctic Boreal Vulnerability Experiment (ABoVE) airborne campaign to understand the sensitivity of longwave radar backscatter intensity and phase to post-fire recovery process of Arctic tundra. The 2007 Anaktuvuk River fire was used as a case study. At 10-year post-fire, we observed a strong increase (>~4 dB) in both the P- and L-band radar backscatter in the severely burned areas, in contrast to limited backscatter differences (VV, VH) between burned and unburned areas at C-band. The polarimetric target decomposition analysis indicated a general trend towards more random surface scattering, and strong increases of the double-bounce and volumetric scattering power at both P- and L-band in the burned areas. Large differences were also observed in the Pauli phase angle and the dominant-scattering-type Touzi phase angle between the burned and unburned areas. The above changes are likely caused by increasing surface roughness and microtopography due to thermokarst development and ice degradation, and increasing subsurface scattering due to an overall drier and deeper active layer in the burned areas

Miller, Charles E.↗
DOE OSTI2023

Fuel Injection Dynamics and Composition Effects on RDE Performance

Rotating detonation engines (RDEs) provide a promising route to substantially increasing cycle efficiency in stationary gas turbines. Much of this increase relies on the ability to achieve consistent pressure gain within the combustor. In particular, the design of injectors that feed fuel and air into the detonation channel plays a crucial role. Such injectors have to ensure proper mixing of fuel and oxidizer, while minimizing backflow of detonation products into the feed plenums, and reduce susceptibility to the complex wave structures that exist within the combustor. From a practical perspective, such RDEs also need to operate with variable fuel composition. When fuel mixtures with components that possess vastly different oxidation pathways and time-scales are used, there could be additional losses through deflagrative burning instead of detonation-driven heat release. Such sensitivity to the complete flow path is akin to the physics of thermoacoustic instabilities in conventional gas turbines. In this sense, RDEs pose a unique research challenge: the performance of the device relies on the small-scale heat release process, which is highly dependent on the flow interactions within the full-scale system. As a result, canonical flow configurations, instrumented with detailed diagnostics or modeled using high-fidelity tools, but only focus on the small-scale processes will not contain the key system-level interactions. At the same time, macroscopic measurements and models that only capture system-level performance will not provide insight into the key sources of pressure losses. These couplings and sensitivities provide a formidable challenge to both experimental and simulation studies of the effects Thus, a joint experimental/computational program designed specifically to address these challenges was undertaken in this program. The focus of this program was on two key topics: a) the interaction between injector flow and the overall wave dynamics within the combustor, and b) the deflagration/detonation structure in multi-component fuels that are of practical interest. Both topics involve interaction of small-scale heat release processes with the geometry-dependent wave structure. Studies focused on the study of full-scale RDE systems, based on a 6-inch conventional annular geometry. Experimentally RDEs were studied using a combination of diagnostics. A combination of optical diagnostics and aero-thermo-acoustic analysis based on a combination of spectral and mode decomposition analysis was used to identify the dynamics of the detonation wave and other secondary waves that exist in the system. These studies have helped the identification and investigation of injector and detonation dynamics arising from coupling, and how they affect RDE mixing, detonation structure, operability and performance. Performance of RDEs was investigated through thrust stand measurements, which was used to evaluate the effective pressure gain generated by the system through the concept of equivalent available pressure. Optical diagnostics were developed and implemented to investigate the distribution of heat release, across the detonation wave. Novel optical diagnostics of NIR imaging was also developed and applied to investigate the high temperature / high pressure distribution across the detonation wave. In order to complement the experiments, the computational tools were geared to simulate the full experimental setup. GPU-based acceleration of the models and computations were developed to enable rapid simulation of the full system. In addition, the use of adaptive mesh refinement, and unstructured grid formulation, enabled the investigation of realistic geometries studied in the laboratory. The simulations produced a wealth of detail on the structure of the detonation wave under different operating conditions. Emphasis was placed on quantifying mixture pre-burning and the impact on wave propagation and structure.

03 NATURAL GAS↗
DOE OSTI2014

Characterization of molecular outflows in the substellar domain

We report here our latest search for molecular outflows from young brown dwarfs and very low-mass stars in nearby star-forming regions. We have observed three sources in Taurus with the Submillimeter Array and the Combined Array for Research in Millimeter-wave Astronomy at 230 GHz frequency to search for CO J = 2 → 1 outflows. We obtain a tentative detection of a redshifted and extended gas lobe at about 10 arcsec from the source GM Tau, a young brown dwarf in Taurus with an estimated mass of 73 M {sub J}, which is right below the hydrogen-burning limit. No blueshifted emission around the brown dwarf position is detected. The redshifted gas lobe that is elongated in the northeast direction suggests a possible bipolar outflow from the source with a position angle of about 36°. Assuming that the redshifted emission is outflow emission from GM Tau, we then estimate a molecular outflow mass in the range from 1.9 × 10{sup –6} M {sub ☉} to 2.9 × 10{sup –5} M {sub ☉} and an outflow mass-loss rate from 2.7 × 10{sup –9} M {sub ☉} yr{sup –1} to 4.1 × 10{sup –8} M {sub ☉} yr{sup –1}. These values are comparable to those we have observed in the young brown dwarf ISO-Oph 102 of 60 M {sub J} in ρ Ophiuchi and the very low-mass star MHO 5 of 90 M {sub J} in Taurus. Our results suggest that the outflow process in very low-mass objects is episodic with a duration of a few thousand years and the outflow rate of active episodes does not significantly change for different stages of the formation process of very low-mass objects. This may provide us with important implications that clarify the formation process of brown dwarfs.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2016

InSAR Detection and Field Evidence for Thermokarst after a Tundra Wildfire, Using ALOS-PALSAR

Thermokarst is the process of ground subsidence caused by either the thawing of ice-rich permafrost or the melting of massive ground ice. The consequences of permafrost degradation associated with thermokarst for surface ecology, landscape evolution, and hydrological processes have been of great scientific interest and social concern. Part of a tundra patch affected by wildfire in northern Alaska (27.5 km 2 ) was investigated here, using remote sensing and in situ surveys to quantify and understand permafrost thaw dynamics after surface disturbances. A two-pass differential InSAR technique using L-band ALOS-PALSAR has been shown capable of capturing thermokarst subsidence triggered by a tundra fire at a spatial resolution of tens of meters, with supporting evidence from field data and optical satellite images. We have introduced a calibration procedure, comparing burned and unburned areas for InSAR subsidence signals, to remove the noise due to seasonal surface movement. In the first year after the fire, an average subsidence rate of 6.2 cm/year (vertical) was measured. Subsidence in the burned area continued over the following two years, with decreased rates. The mean rate of subsidence observed in our interferograms (from 24 July 2008 to 14 September 2010) was 3.3 cm/year, a value comparable to that estimated from field surveys at two plots on average (2.2 cm/year) for the six years after the fire. These results suggest that this InSAR-measured ground subsidence is caused by the development of thermokarst, a thawing process supported by surface change observations from high-resolution optical images and in situ ground level surveys.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2016

A New Group Crystallization Approach in Used Nuclear Fuel Recycling: A Look at Fission Product Behaviors

Nuclear energy has the potential to play a large role in meeting future needs of the U.S. sustainable energy strategy, as a clean, carbon-free power source. However, to take advantage of the inherent benefits, many hurdles must be overcome in order for nuclear power to achieve these expectations. One of the largest challenges faced, is the management of used nuclear fuel (UNF). Currently, no strategy has been identified to deal with the growing UNF problem, and so the UNF remains stored on site at nuclear power plants either in cooling pools or in dry cast storage. The amount of stored UNF continues to grow, and with it, so does the concern surrounding its long-term radiotoxicity. This material could be reprocessed to recover the actinides, maximizing the energy potential of the UNF and minimizing the waste generation. Not only do U and Pu, the major energy producing actinides, need to be recovered, but recovering Np and Am would make waste generated from reprocessing significantly safer for long-term storage in a geological repository. There are a number of methods currently in use to reprocess UNF; throughout Europe, the Purex process is widely implemented, while the Japanese have developed the Next process. The Next process removes a bulk of the U by crystallization prior to a Purex-like separation scheme. In the Next process, it is undesirable to have any other species removed from solution in the crystallization step, but rather the goal is to obtain a pure uranyl nitrate hexahydrate (UNH) product. Alternatively, a group separation of U-Am by a crystallization process would provide an elegant solution. Such a process has become attainable with the renewed interest in accessing Am(VI) in nitric acid solutions. In order to synthesize and stabilize Am(VI), a highly oxidizing system is required, which has only been demonstrated on a limited basis. By oxidizing Np, Pu, and Am to their hexavalent state, they can be co-crystallized with UNH, and thereby removed from solution. Recent results have demonstrated that all the hexavalent actinide (An) species are removed from solution in near proportion, by a simple reduction of temperature in 6-8 M HNO{sub 3}. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1999

An Abundance Analysis of Two Carbon-Rich Proto-Planetary Nebulae: IRAS Z02229+6208 And IRAS 07430+1115

In this paper, we present an LTE abundance analysis of two new proto-planetary nebulae, IRAS Z02229 + 6208 and IRAS 07430 + 1115, based on high-resolution (R approximately equal 55,000) optical echelle spectra. Results show that both stars are metal-poor ([Fe/H] = -0.5) and overabundant in C, N, and s-process elements. The average elemental abundances are [C/Fe] = +0.8, [N/Fe] = +1.2, and [s-process/Fe] = +1.4 for IRAS Z02229 + 6208, and [C/Fe] = +0.6, [N/Fe] = +0.4, and [s-process/Fe] = +1.6 for IRAS 07430+ 1115. These abundances suggest that the stars have experienced nucleo-synthesis on the asymptotic giant branch (AGB), and the resultant products of CNO, 3alpha, and s-process reactions were brought to the photosphere during shell flashes and deep mixing episodes during the AGB phase of their evolution. Of major significance is the measurement of a high Li abundance in both stars, log epsilon(Li) approximately equal 2.3 and 2.4 for IRAS Z02229 + 6208 and IRAS 07430 + 1115, respectively. This may be the result of hot bottom burning, below the deep convective zone. We also present an analysis of the circumstellar molecular (C2 and CN) and atomic (Na I and K I) absorption spectra of both stars. We derive rotational temperatures, column densities, and envelope expansion velocities using molecular C2 Phillips and CN Red system bands. The values derived for expansion velocities, 8-14 km/s, are typical of the values found for post-AGB stars. IRAS 07430+ 1115 is unusual in that it shows P Cygni-shaped C2 emission profiles in the spectra of the circumstellar envelope. A minimum distance for IRAS Z02229+6208, determined from interstellar Na I lines, suggests that it is evolved from an intermediate-mass star. Including these two stars, the number of post-AGB stars for which clear C, N, and s-process elemental overabundances are found rises to eight. IRAS Z02229 + 6208 is known to possess the 21 micron emission feature in its mid-infrared spectrum; these results support the idea that all 21 micron emission stars are carbon-rich post-AGB stars.

Reddy, Bacham E.↗
DOE OSTI2022

A Novel Catalytic Membrane Reactor for DME Synthesis from Renewable Resources

Production of liquid fuels or chemicals from CO 2 (captured from the air or flue gases) and renewable hydrogen presents a new approach to producing clean fuels domestically. While significant progress has been made in the area of renewable electricity generation from solar and wind, a large gap remains with respect to the production of renewable liquid fuels/chemicals. Other processes for producing liquid fuels/chemicals from renewable electricity are constrained by thermodynamic limitations, making them prohibitively expensive and impractical. The team is overcoming these limitations and developing catalytic membrane reactor processes with high yields and low energy penalties. Supported by the Advanced Research Projects Agency-Energy (ARPA-E) of the US Department of Energy (DOE), GTI Energy and partners have been developing a technology for the production of renewable dimethyl ether (DME) from carbon dioxide (CO 2 ) and renewable hydrogen (H 2 ) using a novel catalytic membrane reactor and demonstration of this system at a scale of 1 kg/day. DME is a clean-burning, non-toxic fuel with a high cetane value (55-60), making it an excellent diesel alternative. DME can be stored as a liquid under moderate pressure, eliminating the need for the high-pressure containers used for CNG or cryogenics, as in the case of LNG. DME is also approved as a renewable fuel under the U.S. Environmental Protection Agency’s Renewable Fuels Standard (RFS), making it eligible for Renewable Identification Numbers (RINs) credits. By producing DME through the catalytic conversion of captured CO 2 and renewable H 2 , this process will produce renewable liquid transportation fuel and a means of large-scale utilization of captured CO 2 . In the DME synthesis process, CO 2 and H 2 are fed to a hollow fiber catalytic membrane reactor at 300-600 psig that contains a bi-functional catalyst that combines two reactions, methanol synthesis (CO 2 + 3H 2 → CH 3 OH + H 2 O) and methanol dehydration (2CH 3 OH → CH 3 OCH 3 + H 2 O), into a one-step process to produce DME. The bifunctional catalyst converts methanol to DME, enabling higher overall CO 2 conversion. A Cu/ZnO/ZrO 2 /Al 2 O 3 (CZZA) catalyst is used for methanol synthesis and is coupled with a zeolite catalyst H-ZSM-5 for dehydration. This one-step process intensifies a process that would otherwise require multiple reaction steps. However, combining these two reactions results in increased water production which inhibits catalytic activity. Here, the Na + -gated, water-transport membrane (Science, vol. 367, pp. 667, 2020), removes water in situ, shifting the thermodynamic equilibrium towards product formation while decreasing kinetic inhibition from water adsorption onto the catalyst surface. The Na + gated, water-transport nanochannel membrane showed H 2 O/CO 2 selectivity of 560 at 250 °C and 300 psig for H 2 O/CO 2 /CO/H 2 /MeOH gas mixtures. The selectivities of H 2 O/H 2 , H 2 O/CO, and H 2 O/MeOH were 190, 170, and 80, respectively. In a laboratory-scale membrane reactor, DME synthesis testing using this membrane, a DME production rate of 440 g DME /kg cat /h was achieved at 260 °C and 550 psig. Compared to the packed bed reactor, the CO 2 conversion and DME production rate in the membrane reactor were 80% and three times higher, respectively. A prototype test system (1 kg/day) was designed, constructed, and tested. A DME production rate of 1.31 kg/day and a DME productivity of 360 g/h/kg were achieved in the prototype membrane reactor. Good stability was demonstrated during 150-h continuous operation and multiple startups/shutdowns tests.

10 SYNTHETIC FUELS↗
DOE OSTI2017

Cross-polar transport and scavenging of Siberian aerosols containing black carbon during the 2012 ACCESS summer campaign

During the ACCESS airborne campaign in July 2012, extensive boreal forest fires resulted in significant aerosol transport to the Arctic. A 10-day episode combining intense biomass burning over Siberia and low-pressure systems over the Arctic Ocean resulted in efficient transport of plumes containing black carbon (BC) towards the Arctic, mostly in the upper troposphere (6–8 km). Here, a combination of in situ observations (DLR Falcon aircraft), satellite analysis and WRF-Chem simulations is used to understand the vertical and horizontal transport mechanisms of BC with a focus on the role of wet removal. Between the northwestern Norwegian coast and the Svalbard archipelago, the Falcon aircraft sampled plumes with enhanced CO concentrations up to 200 ppbv and BC mixing ratios up to 25 ng kg –1 . During transport to the Arctic region, a large fraction of BC particles are scavenged by two wet deposition processes, namely wet removal by large-scale precipitation and removal in wet convective updrafts, with both processes contributing almost equally to the total accumulated deposition of BC. Our results underline that applying a finer horizontal resolution (40 instead of 100 km) improves the model performance, as it significantly reduces the overestimation of BC levels observed at a coarser resolution in the mid-troposphere. According to the simulations at 40 km, the transport efficiency of BC (TE BC ) in biomass burning plumes was larger (60 %), because it was impacted by small accumulated precipitation along trajectory (1 mm). In contrast TE BC was small (< 30 %) and accumulated precipitation amounts were larger (5–10 mm) in plumes influenced by urban anthropogenic sources and flaring activities in northern Russia, resulting in transport to lower altitudes. TE BC due to large-scale precipitation is responsible for a sharp meridional gradient in the distribution of BC concentrations. Wet removal in cumulus clouds is the cause of modeled vertical gradient of TE BC , especially in the mid-latitudes, reflecting the distribution of convective precipitation, but is dominated in the Arctic region by the large-scale wet removal associated with the formation of stratocumulus clouds in the planetary boundary layer (PBL) that produce frequent drizzle.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Harnessing biomass-derived reinforcements for sustainable flame-resistant composite

Bio-based composites containing natural fiber reinforcements have been integral to developing innovative, low-cost, and low-energy technologies for transportation applications in marine, automotive, and other industries. The low density of natural fibers gives these materials a high specific stiffness and strength, which can lead to significant weight savings in composites. This study focused on a specialty type of wood fiber treated with boric acid (≤ 7%) sourced from Northern White Pine in the USA, marketed as TimberFill. TimberFill is a high aspect ratio, fibrillated wood fiber that is produced commercially for wood fiber insulation; it is chemically treated to improve both its flame retardance and water resistance. In the present study, TimberFill was processed into non-woven mats using a process akin to papermaking and then infiltrated with epoxy resin. Biochar from wood waste was also incorporated into the epoxy resin as a low-cost filler and functional additive. The effects of biochar concentration on composites’ flame retardance (17% improvement in burn rate), thermal conductivity (improved by 9%), and mechanical performance (33% improvement in modulus) are herein presented. Additionally, it explores the plasticizing effect of the boric acid used in the treatment of TimberFill on the thermal and mechanical properties of the resulting composites, specifically on the thermal expansion coefficient.

Joshy, Joslin [ORNL]↗
DOE OSTI2015

INTERPRETING THE GLOBAL 21-cm SIGNAL FROM HIGH REDSHIFTS. II. PARAMETER ESTIMATION FOR MODELS OF GALAXY FORMATION

Following our previous work, which related generic features in the sky-averaged (global) 21-cm signal to properties of the intergalactic medium, we now investigate the prospects for constraining a simple galaxy formation model with current and near-future experiments. Markov-Chain Monte Carlo fits to our synthetic data set, which includes a realistic galactic foreground, a plausible model for the signal, and noise consistent with 100 hr of integration by an ideal instrument, suggest that a simple four-parameter model that links the production rate of Lyα, Lyman-continuum, and X-ray photons to the growth rate of dark matter halos can be well-constrained (to ∼0.1 dex in each dimension) so long as all three spectral features expected to occur between 40 ≲ ν/MHz ≲ 120 are detected. Several important conclusions follow naturally from this basic numerical result, namely that measurements of the global 21-cm signal can in principle (i) identify the characteristic halo mass threshold for star formation at all redshifts z ≳ 15, (ii) extend z ≲ 4 upper limits on the normalization of the X-ray luminosity star formation rate (L{sub X}–SFR) relation out to z ∼ 20, and (iii) provide joint constraints on stellar spectra and the escape fraction of ionizing radiation at z ∼ 12. Though our approach is general, the importance of a broadband measurement renders our findings most relevant to the proposed Dark Ages Radio Explorer, which will have a clean view of the global 21-cm signal from ∼40 to 120 MHz from its vantage point above the radio-quiet, ionosphere-free lunar far-side.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2017

New measurements of low-energy resonances in the Ne 22 ( p , γ ) Na 23 reaction

The Ne 22 ( p , γ ) Na 23 reaction is one of the most uncertain reactions in the NeNa cycle and plays a crucial role in the creation of Na 23 , the only stable Na isotope. Uncertainties in the low-energy rates of this and other reactions in the NeNa cycle lead to ambiguities in the nucleosynthesis predicted from models of thermally pulsing asymptotic giant branch (AGB) stars. This in turn complicates the interpretation of anomalous Na-O trends in globular cluster evolutionary scenarios. Prior studies of the Ne 22 ( p , γ ) Na 23 , Ne 22 ( He 3 , d ) Na 23 , and C 12 ( C 12 , p ) Na 23 reactions disagree on the strengths, spins, and parities of low-energy resonances in Na 23 and the direct-capture Ne 22 ( p , γ ) Na 23 reaction rate contains large uncertainties as well. Here, we present new measurements of resonances at E r c.m. = 417 , 178, and 151 keV and of the direct-capture process in the Ne 22 ( p , γ ) Na 23 reaction. The resulting total Ne 22 ( p , γ ) Na 23 rate is approximately a factor of 20 higher than the rate listed in a recent compilation at temperatures relevant to hot-bottom burning in AGB stars. Although our rate is close to that derived from a recent Ne 22 ( p , γ ) Na 23 measurement by Cavanna et al. in 2015, we find that this large rate increase results in only a modest 18% increase in the Na 23 abundance predicted from a 5 M ⊙ thermally pulsing AGB star model from Ventura and D'Antona (2005). The estimated astrophysical impact of this rate increase is in marked contrast to the factor of ~ 3 increase in Na 23 abundance predicted by Cavanna et al. and is attributed to the interplay between the Na 23 ( p , α ) Ne 20 and Ne 20 ( p , γ ) Na 21 reactions, both of which remain fairly uncertain at the relevant temperature range.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2017

Exposing Hierarchical Parallelism in the FLASH Code for Supernova Simulation on Summit and Other Architectures

Since roughly 100 million years after the big bang, the primordial elements hydrogen (H), helium (He), and lithium (Li) have been synthesized into heavier elements by thermonuclear reactions inside of the stars. The change in stellar composition resulting from these reactions causes stars to evolve over the course of their lives. Although most stars burn through their nuclear fuel and end their lives quietly as inert, compact objects, whereas others end in explosive deaths. These stellar explosions are called supernovae and are among the most energetic events known to occur in our universe. Supernovae themselves further process the matter of their progenitor stars and distribute this material into the interstellar medium of their host galaxies. In the process, they generate ~1051 ergs of kinetic energy by sending shock waves into their surroundings, thereby contributing to galactic dynamics as well.

Papatheodore, Thomas L.↗
DOE OSTI2014

Demonstration of the Viability and Evaluation of Production Costs for Biomass-Infused Coal Briquettes

This project was split into four main areas, first to identify the best combination of coal and biomass, second, create and test lab quantity of preferred combinations, Third, create a sizeable quantity for larger scale handling and consuming analysis and fourth, to provide analysis for a commercial scale production capacity. Samples of coal and biomass were collected. Five coals, representing the three major coal ranks, were collected including one bituminous, two sub-bituminous, and two lignite samples. In addition, three square bales (~50 lbs/bale) each of corn Stover and switch grass were collected with one bale of each sample processed through a hammer mill to approximately -5 mesh. A third sample of sawdust was collected once experimentation began at the University of Kentucky. Multiple combinations of coal and biomass; coal, biomass, with biomass binder, were tested until a formulation was identified that could meet the requirement criteria. Based on the results of the binderless briquetting evaluations, the CS/Sub-bit combinations was selected for extended evaluation at a 10% biomass addition rate while the WS/Bitum combination was selected for extended evaluation at a 30% biomass-addition rate. With the final results of the selection process complete, the CoalTek continuous production pilot plant in Tucker GA was outfitted with the specialized blending equipment and two 1/4 ton production runs of biomass and binder subbituminous coal briquettes were completed. These briquettes were later used for a calorific test burn at the University of North Dakota. The first formulation included subbituminous coal, corn stover and a corn starch binder the second formulation included subbituminous coal, wheat stover and corn starch binder.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2017

Basic Research Needs for Future Nuclear Energy: Report of the Basic Energy Sciences Workshop for Future Nuclear Energy, August 9-11, 2017

Nuclear power today accounts for approximately 20% of the electrical supply for the US. It provides reliable energy that helps to stabilize the national grid. In contrast to current nuclear power facilities, future concepts operate at higher temperatures, are operationally more efficient, more fully utilize the energy stored within the fuel, and reduce the amount of waste produced. Recent advances in chemistry and materials sciences provide an unprecedented opportunity to develop the critical systems—the fuel, coolant, and structural materials—needed for deployment of advanced nuclear reactor designs. To address the challenge of stringent demands on material systems as their properties and performance continuously evolve over the operational lifetime, the frameworks to uncover the underlying processes that cause reduced performance have been developed over the last decade. There is now the prospect of designing materials that report upon their own damage, are self-healing, and leverage what would be considered deleterious chemical processes to increase their performance within advanced reactor designs. Success will provide an energy source needed to secure a stable and safe energy supply for the nation. To identify the key research directions required to discover the chemical processes and material degradation mechanisms that result in loss of performance of the fuel, coolant, and structural materials, nearly 150 theoreticians, computational experts, and experimentalists from industry, national laboratories, academia, and federal agencies participated in a workshop held in August 2017. Based on the discussions held at the workshop, five Priority Research Directions (PRDs) were identified. These PRDs defined the key scientific challenges that must be met as well as the opportunities that can be exploited to achieve a multi-scale spatial and temporal understanding of fundamental processes that govern the properties and performance of the different material systems required for advanced reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Coal-Waste-Enhanced Filaments for Additive Manufacturing of High-Temperature Plastics and Ceramic Composites

In the United States, coal waste from over a century of mining and burning coal for heat and electricity has accumulated as mountains of coal fly ash and bottom ash and acre-size ponds, coal fines and gob. These materials can be a problem for local communities and water systems. A cost-effective process to utilize high volumes of these coal wastes in a high-value product would be beneficial to those communities by reducing the amount of waste and providing jobs, manufacturing components, and materials from the waste. Many coal-to-products technologies (e.g., carbon fibers, graphene, carbon foam) rely on carefully choosing the starting material and then altering it chemically or thermally to make the products work. Due to the wide variability of composition and coal content in typical coal waste streams, many high-volume coal waste streams are likely to be unsuitable for use in those technologies. Semplastics’ technology has been shown to utilize most types of coal waste successfully without any pre-selection or pre-processing requirements other than a nominal particle-size reduction for wastes like bottom ash. This characteristic of Semplastics’ solution may enable the use of much larger volumes of a wider range of coal wastes than other coal-to-products technologies. In this project, Semplastics leveraged its unique experience with both coal waste (fly ash or coal combustion residuals), resin materials, and 3D printing to develop 3D printer filaments using common coal wastes – bituminous coal fines and fly ash – and researched the feasibility of using other forms of coal waste as fillers. Simple 3D-printed parts were successfully produced from the coal waste enhanced filaments, which were found to have improved strength and stiffness.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

In-Tank Processing Using Low Temperature Aluminum Dissolution: Year 1 Progress Report

The Hanford Site stores approximately 56 million gallons of radioactive legacy defense waste in underground tanks. This study investigates the feasibility of utilizing in-tank low-temperature aluminum dissolution to favorably alter the transport properties of aluminum-rich southeast quadrant waste sludges, thereby de-risking sludge delivery for Direct Feed of High-Level Waste. Specifically, this study aims to assess the rate and extent of gibbsite dissolution under various conditions, including different particle sizes (~10 to 90 µm), NaOH concentrations (1 to 6 M), and the presence of specific analytes such as NO 2 - , NO 3 - , and other aluminum-rich waste background analytes, using simulated waste solids and liquids. Experimental tests were designed to highlight the impact of aluminum leaching on simulated waste transport properties, quantified by the just-suspended mixing speed (NJS), and were conducted under well-mixed, turbulent conditions, ensuring full suspension of gibbsite particles using an overhead mixer. The results suggest that the presence of NO 2 - and NO 3 - , in conjunction with leaching at relatively low free hydroxide contents, improved transport requirements (i.e., lowered NJS) for pure gibbsite slurries. These findings will inform the design of potential in-tank processing systems, optimizing aluminum dissolution for improved waste management in the Hanford Tank Farms.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗