Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Automatic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Magnetometer with a miniature transducer and automatic scanning

The magnetometer is based on the time variation of the magnetic permeability in the magnetic material of its transducer; however, its operation is substantially different from the ordinary flux-gate magnetometer. The transducer uses 0.05 mm diameter plated magnetic wire and is made flat enabling it to make measurements of transverse magnetic fields as close as 0.08 mm from the surface, and it has very good spatial resolution because of its small active region of approximately 0.64 mm by 0.76 mm. The magnetometer uses an inexpensive clip-on millimeter for driving and processing the electrical signals and readout. It also utilizes an automatic scanning technique which is made possible by a specially designed transducer holding mechanism that replaces the ink pen on an X-Y recorder.

Debnam, W. J. J.↗

Automatic electronic fish tracking system

A newly developed electronic fish tracking system to automatically monitor the movements and migratory habits of fish is reported. The system is aimed particularly at studies of effects on fish life of industrial facilities which use rivers or lakes to dump their effluents. Location of fish is acquired by means of acoustic links from the fish to underwater Listening Stations, and by radio links which relay tracking information to a shore-based Data Base. Fish over 4 inches long may be tracked over a 5 x 5 mile area. The electronic fish tracking system provides the marine scientist with electronics which permit studies that were not practical in the past and which are cost-effective compared to manual methods.

Osborne, P. W.↗

Automatic flight performance of a transport airplane on complex microwave landing system paths

Essential characteristics of the U.S. microwave landing system (MLS) and the TCV B-737 aircraft used in flight demonstrations are described, with special emphasis on the analysis of the approach paths. MLS is used to provide the aircraft with guidance for automatic control on complex, curved descending paths with precision turns into short final approaches terminating in landing and rollout, even when subjected to strong and gusty tail- and cross-wind components and severe wind shear. The tracking performance achieved on these paths under MLS guidance is examined in detail, and the wind environment where the flights are conducted are quantified. The flights demonstrate the utility of the wide-area coverage of MLS for curved, descending paths commencing with a standard RNAV approach into a terminal area and continuation of this approach throughout the MLS coverage and onto the runway.

Walsh, T. M.↗

Decision-directed automatic gain control

Logic circuitry determines whether gain fluctuation are result of signal-strength changes or of atypical strings of like data symbols. Automatic Gain Control (AGC) system provides tight control that is independent of short-term, average, received signal energy and has negligible degrading effect on probability of error for signal.

Weber, W. J., III↗

Multiple-camera automatic controller

Device automatically controls exposure time and frame sequencing for three remotely located cameras used for photographing interior of internal-combustion chamber through special viewing ports. Controller is highly applicable in many areas where closely monitored remote photography is required.

Bloam, E. T.↗

Surge protection with automatic reset

Circuit turns power off automatically when surge occurs and restores power when voltage returns to normal. Transmitters and other equipment are protected in electrically noisy environments; however, if three transient overvoltages (or continuous overvoltage) are sensed within 3.2 seconds, circuit turns power supply off permanently since serious failure may have occurred.

Chan, R. B.↗

Automatic thermal switch

Automatic thermal switch closes and opens heat-flow path in response to temperature changes. Control is used to regulate temperature in electronic circuitry or cryogenic refrigeration equipment.

Cunningham, J. W.↗

Progress satellite: An automatic cargo spacecraft

The requirement for resupplying long term orbital space stations is discussed. The operation of Progress (an unmanned automatic resupply spacecraft) is described. It concludes that the development of Progress is a major contribution of Soviet science to domestic and world aeronautics.

Novikov, N.↗

Automatic communication signal monitoring system

A system is presented for automatic monitoring of a communication signal in the RF or IF spectrum utilizing a superheterodyne receiver technique with a VCO to select and sweep the frequency band of interest. A first memory is used to store one band sweep as a reference for continual comparison with subsequent band sweeps. Any deviation of a subsequent band sweep by more than a predetermined tolerance level produces an alarm signal which causes the band sweep data temporarily stored in one of two buffer memories to be transferred to long-term store while the other buffer memory is switched to its store mode to assume the task of temporarily storing subsequent band sweeps.

Bernstein, A. J.↗

Hydrogen maser frequency standard computer model for automatic cavity tuning servo simulations

A computer model of the JPL hydrogen maser frequency standard was developed. This model allows frequency stability data to be generated, as a function of various maser parameters, many orders of magnitude faster than these data can be obtained by experimental test. In particular, the maser performance as a function of the various automatic tuning servo parameters may be readily determined. Areas of discussion include noise sources, first-order autotuner loop, second-order autotuner loop, and a comparison of the loops.

Potter, P. D.↗

Configuration management and automatic control of an augmentor wing aircraft with vectored thrust

An advanced structure for automatic flight control logic for powered-lift aircraft operating in terminal areas is under investigation at Ames Research Center. This structure is based on acceleration control; acceleration commands are constructed as the sum of acceleration on the reference trajectory and a corrective feedback acceleration to regulate path tracking errors. The central element of the structure, termed a Trimmap, uses a model of the aircraft aerodynamic and engine forces to calculate the control settings required to generate the acceleration commands. This report describes the design criteria for the Trimmap and derives a Trimmap for Ames experimental augmentor wing jet STOL research aircraft.

Cicolani, L. S.↗

Circuit for automatic load sharing in parallel converter modules

A nondissipative circuit for automatic load sharing in parallel converter modules having push-pull power transistors is presented. Each transistor has a separate current-sensing transformer and an impedance-adjusting transformer in series with its collector. The impedance-adjusting transformer functions as a current-controlled variable impedance that is responsive to the difference between the peak collector current of the transistor and the average peak current of all collector currents of power transistors in all modules, thereby to control the collector currents of all power transistors with reference to the average peak collector current.

Nagano, S.↗

A computer program to automatically generate state equations and macro-models

A computer program, PROSE, that produces nonlinear state equations from a simple topological description of an electrical or mechanical network is described. Unnecessary states are also automatically eliminated, so that a simplified terminal circuit model is obtained. The program also prints out the eigenvalues of a linearized system and the sensitivities of the eigenvalue of largest magnitude.

Garrett, S. J.↗

Automatic connector for structural beams

Lightweight connector automatically aligns beams to be jointed, and withstands torsion, tension, and compression loads. One beam has connector, other has receptor. Bracket aligns connector and receptor. When actuated, spring in connector pushes shaft into receptor. Hooks on shaft snap to lock into receptor slots. Union can be separated easily without damage. Connectors are designed for in-space assembly, but may be suited to ground assemblies as well.

Von Tiessehausen, G. F.↗

Automatic thermal switches

Two automatic switches control heat flow from one thermally conductive plate to another. One switch permits heat flow to outside; other limits heat flow. In one switch, heat on conductive plate activates piston that forces saddle against plate. Heat carriers then conduct heat to second plate that radiates it away. After temperature is first plate drops, piston contracts and spring breaks thermal contact with plate. In second switch, action is reversed.

Cunningham, J. W.↗

Automatic 35 mm slide duplicator

Automatic duplicator is readily assembled from conventional, inexpensive equipment and parts. Series of slides can be exposed without operator attention, eliminating considerable manual handling and processing ordinarily required. At end of programmed exposure sequence, unit shuts off and audible alarm signals completion of process.

Seidel, H. F.↗

Automatic chemical vapor deposition

Report reviews chemical vapor deposition (CVD) for processing integrated circuits and describes fully automatic machine for CVD. CVD proceeds at relatively low temperature, allows wide choice of film compositions (including graded or abruptly changing compositions), and deposits uniform films of controllable thickness at fairly high growth rate. Report gives overview of hardware, reactants, and temperature ranges used with CVD machine.

Kennedy, B. W.↗