Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ATTENUATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Evaluation of Experimental Shroud Designs for the Hyperion 5201W Infrasound Sensor

Sandia National Laboratories has tested and evaluated various infrasound shrouds, produced Doug Seastrand and Gary Walker, DOE staff in Las Vegas, Nevada, intended for a Hyperion 5201W digital infrasound sensor. The purpose of these shrouds is to improve the infrasound sensor’s attenuation of incoherent signals, specifically those caused by wind passing by the sensor. The purpose of the shroud evaluation was to measure amplitude and phase of the sensors with a variety of shroud designs attached and determine whether there is any appreciable changes in amplitude and/or phase response over the IMS passband for infrasound applications, 0.02 Hz to 4.0 Hz. These shrouds utilize a tubule design that directs and mixes airflow from ports radially distributed at approximately 90 degree offsets in an attempt to minimize wind-generated signal due to Bernoulli effect caused by airflow passing by ports perpendicular to the wind.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2019

Using Passive Seismology to Map the Water within Critical Glacial Ice Sheets

Predictions of the long term stability of the major ice sheets depend on the ability to identify where melt is occurring and to monitor changes over time. Particularly important is the detection of melting along the grounding line, where the glacier is in contact with the solid earth. Melting along the grounding line significantly increases the speed at which glaciers flow, increasing the risk of ice sheet collapse. Passive seismology offers an effective, relatively low cost and precise means of measuring the dynamic changes in the ice. If we can demonstrate its effectiveness, it would allow continuous monitoring of the critical contact between the ice-sheet and the subsurface. The purpose of this study was to determine whether this method can be applied to detect liquid water within the glacial ice system using currently available data. The objectives would be: (1) To identify the attenuation characteristics of glacial ice and the contrast within fractured and fluid-filled zones. (2) To map fluid-solid contacts within the ice sheets and particularly between ice and the underlying solid earth. (3) To identify changes in the system over time. (4) To identify an optimal network configuration for the purposes of monitoring critical points within the glacier

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Engineering CAM Photosynthetic Machinery into Bioenergy Crops for Biofuels Production in Marginal Environments

CAM provides an excellent opportunity to engineer enhanced photosynthetic performance and water-use efficiency (WUE) into bioenergy crops. Our vision was to understand the enzymatic and regulatory pathways required for CAM in order to engineer CAM photosynthetic machinery into Arabidopsis and Populus. Major advances were made in understanding the molecular “parts list” necessary for engineering CAM through the sequencing the genomes and transcriptomes of several model and agronomically important CAM species including Agave, Ananas, Clusia, Kalanchoe, Mesembryanthemum, and Opuntia. Comparison of diel co-expression network analyses in Agave, Ananas, and Kalanchoe with expression patterns in C 3 photosynthesis species revealed the rescheduling of gene expression associated with stomatal opening and closing and led to the identification of many candidate CAM-related genes for further functional testing. Both RNAi-mediated gene silencing and CRISPR/Cas genome editing for gene knockout were used to investigate over 70 CAM-related enzymes, regulatory kinases/phosphatases, and transporters and 25 transcription factors implicated in playing key regulatory roles in CAM. Knockdown of key C 4 cycle enzymes within the carboxylation and decarboxylation modules of CAM not only perturbed CAM itself, but also altered the expression of core circadian clock components demonstrating that loss of CAM function also perturbs the central circadian clock and alters the regulatory patterns of key guard cell signaling genes that are linked with the characteristic inverse pattern of stomatal opening and closing during CAM. An advanced system for joining D.AN fragments from a universal library was developed that automatically maintains open reading frames (ORFs) and does not require linkers, adaptors, regions of sequence homology, amplification (or mutation for domestication) of fragments to function systems for the construction of gene circuits. Alternatively, Gibson assembly was used to create gene circuits consisting of up to 15 unique gene expression cassettes expressing either the core C 4 cycle of CAM comprising carboxylation or decarboxylation modules or both modules together. The expression of each gene cassette was driven by a drought-stress inducible 5’ regulatory region or promoter (and cognate 3’ terminator region) from A. thaliana so that CAM gene expression would be enhanced under conditions of water-deficit stress. These gene circuits were introduced into the C 3 photosynthesis model species A. thaliana. Expression of the nocturnal carboxylation module resulted in increased biomass and seed yield arising from net CO 2 fixation at night and malate accumulation typical of a CAM plant along with daytime CO 2 fixation typical of a C 3 photosynthesis plant. To create a leaf anatomy suited for the optimal performance of CAM in a C 3 photosynthesis plant, increased tissue succulence was engineered in A. thaliana (and Nicotiana sylvestris), which also improved biomass and seed yield and drought attenuation and improved salinity tolerance. The basic CAM Biodesign principles described in this report can be extended to increase the productivity and WUE of food and bioenergy crops and are expected to have broad applicability and ensure sustainable biofuel feedstock production in the face of the global climate crisis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2019

Large Area Airborne Contamination Monitoring

Current D&D operations at Hanford have demonstrated a flaw in the current state of the art capability of defining airborne contamination boundaries. Airborne particulate emissions of Pu-239 from CM2H operations on the Hanford Pu Finishing Plant were detected well beyond areas controlled for airborne plutonium, putting numerous workers at risk for radiological assimilations. Forty-two Hanford workers had positive bioassay results for plutonium uptake. Work areas determined to be free of airborne contamination as measured by state-of-the-art continuous alpha monitoring (CAM) systems were later discovered not to be. Airborne contamination was scattered to a such degree that CAM systems were surveying insufficient volumes of air to accurately predict where respiratory protection was required. A $\$ 19,000$ state of the art portable CAM system used at both Hanford and at SRS screens air for alpha activity at the rate of 1 CFM. This research project will explore the feasibility of using commercially available air purifying systems to screen significantly larger volumes of air for airborne actinide contamination. Commercial household HEPA based air purifying units screen large volumes of air, a simple $\$ 300$ unit being looked at for this study could screen a volume of air that would require over 300 of the $\$ 19,000$ CAMs. The goal of the project was to determine the feasibility of building a detection system capable of screening the air purifiers pre-filters and HEPA filters for any actinide bearing hot particles that have been captured. The simplest technologies available to Field-Radiological-Protection personnel are hand-held alpha field survey meters. With the size and the corrugated structure of these HEPA filters, hand screening is not practical. This project researched alternatives capable of automating this function. Two potential technologies were examined. One technology evaluated was the measurement of xray emissions from the actinides, taking advantage of the higher emission rates of the L x-rays compared to the gamma emissions of isotopes such as Pu-238 or Pu-239. High resolution to low resolution systems were evaluated. Branching ratio data on the actinides in the literature is incomplete, and a study was initiated to measure branching ratios of the various L emissions of a number of the plutonium isotopes. A Monte Carlo simulation was also run to calculate the effect the attenuating HEPA media would have on x-ray measurements on spectrometers centered in each quadrant above the surface of the HEPA. The second technology evaluated was measuring the light from a scintillating media applied to the surface of the HEPA filter using a ThorLabs Scientific-Grade Digital Camera Model 8051M. A light tight enclosure capable of holding the 2’x2’x1” HEPA filter was fabricated. Numerous scintillation media were evaluated for both the sensitivity and for resolution of measuring alpha activity. Figure 1 shows images of a 4”x4” section of HEPA filter with a 3 x 3 grid of Pu-238 contamination loaded inside the crevices of the HEPA.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2019

Site Environmental Report for 2018

Lawrence Berkeley National Laboratory (LBNL, Berkeley Lab) is a multi-program scientific facility operated by the University of California (UC) for the U.S. Department of Energy (DOE). Berkeley Lab’s research is focused on the physical, biological, environmental, and computational sciences, with the objective of delivering scientific knowledge and discoveries pertinent to DOE’s mission. This annual report describes environmental protection activities and potential impacts resulting from LBNL operations conducted in 2018. The format and content of this report satisfy the requirements of both DOE Order 231.1B, Administrative Change 1 (Environment, Safety, and Health Reporting) and the operating contract between UC and DOE (DOE Contract No. DE-AC02-05CH11231, also known as Contract 31). LBNL activities are planned and conducted with full regard to protecting employees, the public, and the environment, as well as complying with all applicable environmental, safety, and health laws and regulations. As presented in Chapter 2, Berkeley Lab implements an Environmental Management System (EMS) to oversee environmental compliance activities and continually improve overall environmental performance while maintaining operational capability and sustaining its overall mission. The effectiveness of the EMS and environmental programs is reviewed annually as part of the performance evaluation process of Contract 31. For fiscal year (FY) 2018, which began October 1, 2017, and ended September 30, 2018, the EMS was given a performance rating of B plus for its management of environmental activities (on a scale from A plus as the highest grade, to F as the lowest). The measurement and rating system was developed jointly by Berkeley Lab, UC, and DOE. The FY 2018 rating was based on how Berkeley Lab met the objective in DOE’s FY 2018 Performance Evaluation and Measurement Plan (Appendix B in Contract 31, Section J) of providing an efficient and effective EMS. Six significant accomplishments, which ranged from effective teaming on projects and with regulatory agencies to improved program assessment approaches, were factors in the rating. The EMS was also graded through the federal Office of Management and Budget’s annual EMS performance metrics, in which a reporting scorecard rates elements of the International Organization for Standardization (ISO) 14001 standard and the degree of integration between the EMS and Berkeley Lab’s sustainable practices. Overall scores fall into one of three categories: green (highest), yellow (middle), or red (lowest). For FY 2018, Berkeley Lab received a score of green. A week-long formal conformity audit of the EMS was conducted at the end of July by a qualified external party, as is required every three years. The audit team found that Berkeley Lab’s EMS continues to conform to the ISO standard with no major nonconformance. An overview of environmental protection and restoration programs is provided in Chapter 3, including information about compliance activities, operating permits, and regulatory agency inspections and audits that occurred during 2018. Twenty-one minor violations and two Class II violations were issued during agency inspections of programs governing aboveground and underground storage tanks, hazardous waste treatment units, hazardous waste storage areas, hazardous materials management, and wastewater, stormwater, and air emission sources. This report also includes information on environmental monitoring performed in 2018 (Chapter 4). The results of these monitoring activities confirmed that groundwater cleanup actions have been effective in reducing concentrations of volatile organic compounds (VOCs) in the groundwater, although concentrations appear to be reaching asymptotic levels in some areas. Site groundwater plumes are stable or are attenuating, and VOCs are not migrating off site. All emissions and discharges from LBNL operations were within environmental compliance release limits except oxides of nitrogen and carbon monoxide from boilers (under 5 million BTUs) from Buildings 2, 66, and 88. The radiological dose assessments (Chapter 5) performed in 2018 concluded that the maximum potential dose to a hypothetical resident from Berkeley Lab’s airborne radionuclide releases was approximately 0.04% of the DOE and U.S. Environmental Protection Agency annual limit of 10 millirem per year (mrem/yr); the potential dose from all radiation sources at Berkeley Lab was approximately 0.15% of the average natural background radiation dose of 310 mrem/yr in the United States, and about 0.5% of the DOE annual limit of 100 mrem/yr from all sources.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Technology Summary L-21044 Tunnel Sensor Hydrogeology Evaluations

Illicit tunneling along the U.S. Mexican border is a persistent national security problem. Several types of sensors could be to used to detect tunnels, but the hydrogeology of the subsurface makes some technologies ineffective. This effort used available borehole and surface geology data to develop 3D hydrogeologic models, which could then provide the input for optimizing subsurface sensor technologies to detect tunnels. Depending on the specific type of sensor, the following physical properties of the subsurface are important: longitudinal speed (velocity-p), shear speed (velocity-s), acoustic attenuation, electrical permittivity, electrical conductivity, density and elastic properties. LLNL developed a procedure which uses hydrogeological datasets to determine 3D hydrogeology cross sections. The physical properties of the rocks are generally not known precisely, thus ranges of properties would need to be considered. This cross-section data can then be utilized to enhance modeling studies to optimize sensor types/systems.

58 GEOSCIENCES↗
DOE OSTI2020

Characterizing Baselines and Change in Gas Hydrate Systems using EM Methods

The objective of this project was to advance our understanding of gas hydrate systems in nature by characterizing their electrical properties in the field and in the laboratory. In the laboratory measurements, methane hydrate was synthesized from pure water ice and flash frozen seawater, with varying amounts of sand or silt added. Electrical conductivity was determined by impedance spectroscopy, using equivalent circuit modeling to separate the effects of electrodes and to gain insight into conduction mechanisms. Silt and sand increase the conductivity of pure hydrate, inferred to be contaminant NaCl contributing to conduction in hydrate, to a peak conductivity in agreement with peak resistivities observed in well logs through massive hydrate (3,000--10,000 Ωm). The addition of silt and sand lowers the conductivity of hydrate synthesized from seawater, by an amount consistent with Archie's Law. All samples were characterized using cryogenic scanning electron microscopy and energy dispersive spectroscopy, which shows good connectivity of salt and brine phases. Electrical conductivity measurements of pure hydrate and hydrate mixed with silt during pressure-induced dissociation supports previous conclusions that sediment increases dissociation rate. In order to characterize gas hydrate systems in the field, we collected 360 line kilometers of controlled-source electromagnetic data on Walker Ridge 313, Orca Basin (WR100), Mad Dog (GC781), and Green Canyon 955 in the Gulf of Mexico, all areas with known or seismically inferred gas hydrate deposits and which have be drilled or targeted for future drilling. We deep-towed an EM transmitter that generates an alternating electric field which propagates through the seafloor geology. Data were recorded on 6 receivers towed behind the transmitter at distances between 550 and 1550 m. In the presence of conductive geology, the electric fields will be attenuated, and conversely, in resistive geology the fields will be preserved. Our data were inverted using a 2D inversion method that first optimizes the model-data misfit, then finds the smoothest model fitting the data. This ensures that resistivity structures present in the final model are likely necessary. At each of the proposed drilling sites we found increased resistivity, interpreted as increased hydrate concentrations. However, not only were the primary drilling sites not always more resistive than the alternate sites, at WR313 the strongest resistors were not at the locations targeted for drilling.

03 NATURAL GAS↗
DOE OSTI2019

Simulation Studies Of Photon Signal Reconstruction In The DUNE Single Phase Far Detector With Xe Doping

Xenon when doped to argon has the potential to increase the effectiveness of scintillation systems in liquid argon time projection chambers (LArTPC). To test the potential improvements, a simulation study was conducted. A simulation of light going through liquid Argon and Xenon photon libraries (photon libraries are used to reduce the amount of computational power needed for interactions that produce a large amount of photons), comparing differences in their properties. The study found more light being emitted in a shorter time by Xe than by Ar with less attenuation present. Preliminary results show lower efficiency of Ar at closer distances. It's unclear whether this is due to inherit properties of the Xe or a result of selection cuts not being optimized. These potential improvements are being looked into for future neutrino experiments such as the Deep Underground Neutrino Experiment (DUNE).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Determination of Stress-Free Lattice Spacing (D₀) for Residual Stress Relaxation Measurement in Ni-based Superalloys by Neutron Diffraction

The residual stress and its relaxation in critical engineering components are key to structural materials reliability. The determination of residual stress in bulk engineering structures like Ni-based superalloys can be conducted by measuring the lattice strain with penetrating neutron diffraction. The state-of-the-art engineering diffraction beamline VULCAN at the Oak Ridge National Laboratory (ORNL) Spallation Neutron Source (SNS) provides the critical capability to evaluate the residual strain/stress relaxation in engineering component thanks to the high flux and event data features. By the means of residual stress/strain calculation, it is critical to accurately determine the stress-free lattice spacing d₀, which can be altered by the change of chemistry, unrelieved stress, and measurement scheme. Here we reported d₀ determination for determining residual stress relaxation and distribution in Alloy 718 superalloys after different quenching treatments. Selection of locations for d₀ measurement was discussed by considering the neutron path, attenuation and sample alignment. A dynamic d₀ that resulted from atom diffusion and chemistry change was estimated as function of time for the in-situ relaxation characterization. It demonstrated how the dynamic d₀ values may influence on the strain calculation in different thermally treated samples. The results highlight the importance of dynamic d₀ for in-situ relaxation involving chemical changes and provide guidance to the dynamic d₀ measurement and simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Isotopic analysis of plutonium measured with very thick absorbers and high-granularity spectra

FRAM is LANL-designed software designed to extract plutonium and uranium isotopic information from gamma ray spectra. This is an important capability for NEST and STAB; however, FRAM performance has been poor when applied to field data collected in these programs. FRAM Version 5 (commercially available) was fine-tuned and validated for laboratory quality measurements but not for measurements of the high-mass and heavily shielded SNM items encountered in NEST. FRAM is untested for spectra collected with high-granularity lower resolution instruments such as the new 8-MeV Detective-X favored by STAB or the new custom electrocooled systems coming into use for NEST. FRAM Version 6.1 (unreleased) has improvements in physics capabilities, and parameter sets may be adapted that are more specific to NEST and STAB, which is what we have attempted for this assignment. Thick shielding attenuates gamma rays profoundly, especially those at low energy, making them too weak to be measured. The missing low-energy peaks force the analysis to employ only the highest-energy peaks. We adapted FRAM 6.1 for analysis of plutonium spectra obtained with very thick Pb filters (a surrogate for NEST-type configurations). New parameter sets employing only very high energy peaks were created for the analysis. High granularity and low resolution make deconvolution of the 600-keV region particularly challenging, and we have worked to optimally extract information from this region. The results shown in this paper give high confidence that we are on the right track. We used a combination of real and synthetically-modified data. Remaining work includes testing the new software and parameters against genuine data collected with Detective-X and new NEST systems, but such datasets at the moment are unavailable. It also remains to develop and test parameter sets specific to uranium and the new detectors.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2020

Electromagnetic Pulse in Wide-Angle Gamma Shadows

Unavoidable masses external to the warhead, associated with collateral EMP scenarios of current interest, produce a gamma shadow which changes the EMP seen in the shadowed region compared to that in the absence of a shadow. Calculations with the author’s three-dimensional MACSYNC code for a ground observer under the burst show shadowed field rise times ranging from many tens to hundreds of microseconds, durations approaching a millisecond, and magnitudes similar to those of the unshadowed field, depending on gamma shadow angle. These fields are likely to be smaller for larger observer ground ranges because the source region will shift to higher altitudes with associated higher conductivity that will attenuate the field.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2020

Ka-Band ARM Zenith Radar Corrections (KAZRCOR, KAZRCFRCOR) Value-Added Products

The Ka-Band Atmospheric Radiation Measurement (ARM) Zenith Radar Corrections (KAZRCOR) and KA-Band ARM Zenith Radar CF-Radial, Corrected (KAZRCFRCOR) value-added products (VAPs) perform several corrections to the ingested KAZR moments and also create a significant detection mask for each radar mode. The VAPs compute gaseous attenuation as a function of time and radial distance from the radar antenna, based on ambient meteorological observations, and correct observed reflectivities for that effect. Mean Doppler velocities are dealiased to correct velocities whose magnitudes exceed the radar’s Nyquist velocity. Input KAZR data fields are passed through to the KAZRCOR or KAZRCFRCOR output files, in their native time and range coordinates. Complementary corrected reflectivity and velocity fields are provided, along with a mask of significant detections and a number of data quality flags. This report covers the KAZRCOR VAP as applied to the original KAZR radars and the upgraded KAZR2 radars. Originally, prior to late 2019, there were two separate code bases for the different radar versions. Following the harmonization of KAZR and KAZR2 data formats in 2019, only a single code base is required. The new combined KAZR and KAZR2 code base is called the KAZRCFRCOR VAP. The ‘cfr portion of the VAP name refers to the Radial Climate and Forecasting data format standards that are used in these data sets. Throughout this report, references to ‘KAZRCOR’ should be taken to apply to the ‘KAZRCFRCOR’ VAP as well unless there is an explicit statement to the contrary.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

HEMP Testing of Substation Yard Circuit Breaker Control and Protective Relay Circuits

There are concerns about the effects of High-Altitude Electromagnetic Pulses (HEMP) on the electric power grid. Activities to date tested and analyzed vulnerability of digital protective relays (DPRs) used in power substations, but the effect of HEMP on the greater substation environment is not well known. This work establishes a method of testing the vulnerability of circuit breaker control and protective relay circuits to the radiated E1 pulse associated with HEMP based on coupling to the cables in a substation yard. Two DPRs from Schweitzer Engineering Laboratories, Inc. were independently tested. The test setup also included a typical cable in a substation yard with return plane to emulate the ground grid and other ground conductors near the yard cable, cabinetry housing the installed DPRs, station battery and battery charger, terminal block elements, and a breaker simulator to emulate a substation yard configuration. The DPRs were powered from the station battery and the transformer inputs energized with a three-phase source to maintain typical operating conditions during the tests. Vulnerability testing consisted of a conducted E1 pulse injected into the center of the yard cable of the DPR circuits. Current measurements on the yard cable and DPR inputs indicated significant attenuation of the conducted pulse arriving at the control house equipment from the emulated substation yard. This reduction was quantified with respect to the equivalent open-circuit voltage on the yard cable. No equipment damage or undesired operation occurred on the tested circuits for values below 180 kV, which is significantly higher than the anticipated coupling to a substation yard cable.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Low-frequency Electromagnetic Detection Limits of Underground Nuclear Explosions

Underground nuclear explosions produce a broadband electromagnetic signal that can propagate to the surface at some distance. We perform a logistic regression on historical electromagnetic detections to calculate a probabilistic detection curve for prediction of the propagation distance for any given underground nuclear explosion. The curve predicts positive detections at scaled ranges of 2414.6, 2025.7, 1908.3, and 1672.4 m/ktonne 1/3 at probabilities of 50, 90, 95 and 99%, respectively. For a theoretical 100 ktonne underground nuclear explosion these scaled ranges translate to absolute ranges of 11.2, 9.4, 8.9, and 7.8 km at probabilities of 50, 90, 95 and 99%, respectively. We also motivate a need for improved electromagnetic sensor design and deployment by extending the detection analysis using the quoted signal-to-noise ratio of two and noise amplitude of 10 pT along with attenuation relationships that go as 1/r to 1/r 3 . We find that reducing the noise floor by a factor often could extend the detection limit to approximately 5 to 25 km/ktonne 1/3 , which translates to 24 to 112 km for a theoretical 100 ktonne underground nuclear explosion.

58 GEOSCIENCES↗
DOE OSTI2020

Applied Science Investigations to Facilitate Closure of the F-Area and H-Area Seepage Basins

This report provides a roadmap of applied science studies that will facilitate reaching long term monitoring end state corrective actions for groundwater contamination at the F-Area Seepage Basins and the H-Area Seepage Basins at the Savannah River Site in Aiken, SC. The F-Area and H-Area Seepage Basins are waste units on the Savannah River Site in Aiken, SC at which low-level radioactive solutions were disposed into unlined basins, resulting in groundwater contamination. The current contaminants of interest in the groundwater are tritium, iodine-129, strontium-90, uranium isotopes and nitrate. Remediation at both sites has continued since 1988, consisting of closure and capping of the basins, operation of a groundwater pump-and-treat system from 1997 to 2004, and replacement of this system with a comprehensive in situ attenuation-based remedy. This report was requested by the U.S. Department of Energy - Office of Environmental Management in consultation with the Savannah River National Laboratory and Savannah River Nuclear Solutions - Area Completions Projects to provide a scientific basis for proactively addressing groundwater issues that may need to be resolved prior to final corrective actions at the F-Area and H-Area Seepage Basins.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Accobeam - Acoustic Collimated Beam

Researchers at Los Alamos have developed a collimated acoustic imaging technology for non-destructive characterization of highly attenuating media, such as concrete, rocks, mud, and metal casings. The technology is used to investigate structural defects that could compromise important assets such as well boreholes, building structures and sensitive materials like explosives. Current acoustic methods are often unable to penetrate such materials deeply for more informative analysis, which limits what can be learned about asset structural integrity, crucial information companies require to make investment decisions such as fixing or replacing structures well before assets are completely compromised. ACCObeam provides requisite penetration and high-resolution acoustic imaging with applications in borehole imaging, explosives threat evaluation, and structural health evaluation. This technology will potentially save companies significant money by producing accurate and useful visual analyses to better understand the actual condition of assets in the field and respond accordingly. Los Alamos is searching for a collaboration partner to develop this technology for commercial applications that will lead to licensing opportunities for broad industry deployment.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Demonstrate embedding of sensors in a relevant microreactor component

This report describes the first successful embedding of sensors in stainless steel pipe specimens and a miniature hex block to support structural health monitoring of microreactor components during electrically heated testing in non-nuclear testbed facilities. Sensors were embedded with an ultrasonic additive manufacturing process that uses a combination of downward pressure and an ultrasonic scrubbing motion to bond stainless steel foils to underlying materials. After placing sensors within cavities that have been machined to the size of the sensors, the ultrasonic bonding process fills the gaps around the sensors and embeds them within the part. Both Type K thermocouples and spatially distributed fiber-optic strain sensors were successfully embedded within two pipe specimens and a miniature hex block. After the fiber-optic sensors were embedded, they were interrogated and found to have minimal signal attenuation within the embedded region—a significant improvement compared to previous trials. This is likely because of the low-bend-loss fiber that was used, which greatly reduces microbending losses that occur after the embedding process. In addition to showing minimal signal attention, the fibers also showed adequate compressive strain, which is a strong indication that the sensors are physically embedded in the parts as opposed to simply being loosely contained inside the machined cavities. The embedded fibers were able to capture the strain induced in one of the pipe specimens while the pipe was actively heated with a moving heat source.

42 ENGINEERING↗
DOE OSTI2020

Guidance for Monitoring Passive Groundwater Remedies Over Extended Time Scales

Passive remediation can be appropriate where natural processes and actions such as institutional controls mitigate exposure to contaminated groundwater, achieving remedial action objectives and protectiveness of human health and the environment. Monitored natural attenuation (MNA) is a prevalent passive remediation strategy supported by a regulatory framework and monitoring design guidance. MNA can also be used after active remediation has been completed (e.g., pump-and-treat) as a polishing step to reach ultimate remedial action objectives. However, MNA and existing monitoring guidance primarily target situations where the remedial action objectives are met within a few decades. When timescales for passive remediation extend to many decades, a corresponding change in monitoring strategy is needed to adapt to the extended time scale. This document provides guidance for implementing an extended-scale monitoring (ESM) approach appropriate for long-duration passive remediation. Extended-scale is defined in this document with respect to time (i.e., a long duration of remediation) and a large enough physical scale such that receptors will not be impacted within the remediation timeframe.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗