SEARCH · Engineering Papers

Results for “youngs modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Time dependent deformation of a basalt at low differential stress

A detailed study of linear elastic deformation in Ralston basalt during triaxial loading has been made as a function of strain rate (8 x 10 to the -8th per sec to 5 x 10 to the -5th per sec) and moisture content under constant confining pressure (500 bars) and temperature (20 C). Young's modulus was found to be constant and independent of moisture content and strain rate; however, Poisson's ratio decreased 5.7 plus or minus 1.6% and 6.7 plus or minus 1.6% per order of magnitude increase in strain rate for two suites of dry samples and 1.4 plus or minus 1.2% per equivalent change in strain rate for one suite of wet rocks. Lateral expansion in dry rocks is therefore a more sensitive function of strain rate than it is in wet rocks. It is suggested that this strain-rate dependence is related to microcracking.

Brodsky, N.↗

NASA NTRS1979

Carbon fiber modification

The effect of several chemical treatments on the electrical and mechanical properties of carbon fibers was investigated with an optimum goal of increasing the electrical resistivity by a factor of 1000 without appreciably changing the mechanical properties. It was possible to effect resistivity increases from 10 to 50 percent without adversely affecting the tensile strength or Young's modulus for T-300 and C-6000 PAN fibers by treatments with either AlCl3 or nitric acid mixtures. Larger increases in the resistivity were produced with pitch fibers treated with nitric acid mixtures. This treatment also produced a partial decomposition of the pitch fiber and deterioration of the mechanical properties. The rationale behind the approch was to immobilize the conductivity producing pi electrons in the microscopic aromatic structure of the carbon fibers without destroying the strength producing sigma bonds. The investigations indicate that certain chemical treatments can produce such results, but the total reduction in the electrical conductivity which was achieved was not large enough to impact on problems which might arise from the high conductivities of the fibers.

Thompson, T. E.↗

NASA NTRS1981

Relationship between the ideal tensile strength and the friction properties of metals in contact with nonmetals and themselves

The adhesion and friction properties of metals in contact with diamond, boron nitride, silicon carbide, manganese-zinc ferrite, and the metals themselves in vacuum was investigated. An estimate of the ideal uniaxial tensile was obtained in terms of the equilibrium surface energy, interplanar spacing of the planes perpendicular to the tensile axis, and the Young's modulus of elasticity. The coefficient of friction for metals was found to be related to the ideal tensile strength of metals. The higher the strength of the metal, the lower the coefficient of friction.

Miyoshi, K.↗

NASA NTRS1981

An evaluation of the sandwich beam compression test method for composites

The sandwich beam in a four-point bending compressive test method for advanced composites is evaluated. Young's modulus and Poisson's ratio were obtained for graphite/polyimide beam specimens tested at 117 K, room temperature, and 589 K. Tensile elastic properties obtained from the specimens were assumed to be equal to the compressive elastic properties and were used in the analysis. Strain gages were used to record strain data. A three-dimensional finite-element model was used to examine the effects of the honeycomb core on measured composite mechanical properties. Results of the analysis led to the following conclusions: (1) a near uniaxial compressive stress state existed in the top cover and essentially all the compressive load was carried by the top cover; (2) laminate orientation, test temperature, and type of honeycomb core material were shown to affect the type of beam failure; and (3) the test method can be used to obtain compressive elastic constants over the temperature range 117 to 589 K.

Shuart, M. J.↗

NASA NTRS1982

Correlation of tensile and shear strengths of metals with their friction properties

The relation between the theoretical tensile and the shear strengths and the friction properties of metals in contact with diamond, boron nitride, silicon carbide, manganese-zinc ferrite, and the metals themselves in vacuum was investigated. The relationship between the actual shear strength and the friction properties of the metal was also investigated. An estimate of the theoretical uniaxial tensile strength was obtained in terms of the equilibrium surface energy, interplanar spacing of the planes perpendicular to the tensile axis, and the Young's modulus of elasticity. An estimate of the theoretical shear strength for metals was obtained from the shear modulus, the repeat distance of atoms in the direction of shear of the metal and the interplanar spacing of the shear planes. The coefficient of friction for metals was found to be related to the theoretical tensile, theoretical shear, and actual shear strengths of metals. The higher the strength of the metal, the lower the coefficient of friction.

Miyoshi, K.↗

NASA NTRS1982

Effect of 1.33 Mev gamma radiation and 0.5 Mev electrons on the mechanical properties of graphite fiber composites

Epoxy/graphite fiber, polyimide/graphite fiber, and polysulfone/graphite fiber composites were exposed to 1.33 Mev gamma irradiation and 0.5 Mev electron bombardment for varying periods of time. The effects of the irradiation treatments on the breaking stress and Young's modulus were studied by a three point bending test. Effects were small; both electron radiation up to 5000 Mrad and gamma radiation up to 350 Mrad resulted in slight increases in both stress and modulus.

Fornes, R. E.↗

NASA NTRS1982

Tensile stress-strain behavior of graphite/epoxy laminates

The tensile stress-strain behavior of a variety of graphite/epoxy laminates was examined. Longitudinal and transverse specimens from eleven different layups were monotonically loaded in tension to failure. Ultimate strength, ultimate strain, and strss-strain curves wee obtained from four replicate tests in each case. Polynominal equations were fitted by the method of least squares to the stress-strain data to determine average curves. Values of Young's modulus and Poisson's ratio, derived from polynomial coefficients, were compared with laminate analysis results. While the polynomials appeared to accurately fit the stress-strain data in most cases, the use of polynomial coefficients to calculate elastic moduli appeared to be of questionable value in cases involving sharp changes in the slope of the stress-strain data or extensive scatter.

Garber, D. P.↗

NASA NTRS1982

The crack problem for a nonhomogeneous plane

The plane elasticity problem for a nonhomogeneous medium containing a crack is considered. It is assumed that the Poisson's ratio of the medium is constant and the Young's modulus E varies exponentially with the coordinate parallel to the crack. First the half plane problem is formulated and the solution is given for arbitrary tractions along the boundary. Then the integral equation for the crack problem is derived. It is shown that the integral equation having the derivative of the crack surface displacement as the density function has a simple Cauchy type kernel. Hence, its solution and the stresses around the crack tips have the conventional square root singularity. The solution is given for various loading conditions. The results show that the effect of the Poisson's ratio and consequently that of the thickness constraint on the stress intensity factors are rather negligible.

Delale, F.↗

NASA NTRS1981

Effect of physical aging on stress relaxation of poly/methyl methacrylate/

A study was made on the stress relaxation behavior at 25 C of poly(methyl methacrylate) in uniaxial tension as a function of physical aging at both room temperature and 60 C. Test specimens were compression molded at 165 C, then quenched to room temperature and allowed to age for up to 30 days prior to testing. Stress relaxation curves measured after different aging times could be superposed to a single master curve for each aging temperature. Superposition was achieved by applying vertical and horizontal shifts. Hence, the shape of the response curves was not changed by aging. This is in accordance with observations made by Struik for tensile creep curves. Volume changes as a function of physical aging were also determined. Simple exponential relationships were observed between volume and both horizontal and vertical shifts. The horizontal shift implies a shift in the effective time scale caused by a change in free volume. The vertical shifts could be correlated with changes in Young's modulus caused by a change in density. For the range of aging studied, the response time scale varied over nearly two decades of log-time. For the same conditions modulus varied by 30 percent.

Cizmecioglu, M.↗

NASA NTRS1983

The crack problem for a nonhomogeneous plane

Delale, F.↗

NASA NTRS1984

Crack tip field and fatigue crack growth in general yielding and low cycle fatigue

Fatigue life consists of crack nucleation and crack propagation periods. Fatigue crack nucleation period is shorter relative to the propagation period at higher stresses. Crack nucleation period of low cycle fatigue might even be shortened by material and fabrication defects and by environmental attack. In these cases, fatigue life is largely crack propagation period. The characteristic crack tip field was studied by the finite element method, and the crack tip field is related to the far field parameters: the deformation work density, and the product of applied stress and applied strain. The cyclic carck growth rates in specimens in general yielding as measured by Solomon are analyzed in terms of J-integral. A generalized crack behavior in terms of delta is developed. The relations between J and the far field parameters and the relation for the general cyclic crack growth behavior are used to analyze fatigue lives of specimens under general-yielding cyclic-load. Fatigue life is related to the applied stress and strain ranges, the deformation work density, crack nucleus size, fracture toughness, fatigue crack growth threshold, Young's modulus, and the cyclic yield stress and strain. The fatigue lives of two aluminum alloys correlate well with the deformation work density as depicted by the derived theory. The general relation is reduced to Coffin-Manson low cycle fatigue law in the high strain region.

Minzhong, Z.↗

NASA NTRS1983

Thermal stresses in bonded solar cells - The effect of the adhesive layer

A two-dimensional, rectangular model of a proposed solar cell structure is analyzed as two plate elements bonded with an elastic continuum. The governing equations are formulated using the principle of minimum potential energy, with displacement components that vary linearly through the thickness of the adhesive layer. An approximate solution is constructed for a particular class of material properties and is characterized by a boundary layer near the unloaded edge. Both interface stress components achieve their largest values at the edge, and the maximum shear stress is independent of the Young's Modulus of the substrate.

Williams, H. E.↗

NASA NTRS1984

Processing of sintered alpha SiC

Processing methods of sintered alpha SiC for engine applications are developed in a cost effective manner, using a submicron sized powder blended with sintering aids (boron and carbon). The processes for forming a green powder compact, such as dry pressing, cold isostatic pressing and green machining, slip casting, aqueous extrusion, plastic extrusion, and injection molding, are described. Dry pressing is the simplest route to component fabrication, and is carried out at approximately 10,000 psi pressure, while in the cold isostatic method the pressure could go as high as 20,000 psi. Surfactants are added to control settling rates and casting characteristics in the slip casting. The aqueous extrusion process is accomplished by a hydraulic ram forcing the aqueous mixture through a die. The plastic forming processes of extrusion and injection molding offer the potential of greater diversity in shape capacity. The physical properties of sintered alpha SiC (hardness, Young's modulus, shear modulus, and thermal diffusivity) are extensively tested. Corrosion resistance test results of silicon carbide are included.

Storm, R. S.↗

NASA NTRS1985

Solid Rocket Motor Case (SRMC) dynamic sensitivity to changes in composite properties

Traditional composite lamination theory was used to compute the constitutive matrices using a potential range of lamina properties. Sensitivity of vibrational frequencies was examined for variations in constituent materials and geometric properties. The material component interactions examined were the lamina longitudinal and transverse Young's modulus, the lamina Poisson's ratio, and the shear modulus. Fiber and resin properties were related to the frequency response through lamina properties. Geometric properties examined are void ratio and helical wind angle. Capabilities and applications of the SPAR and NASTRAN computer codes are examined for laminated cylindrical shells.

Tolbert, R. N.↗

NASA NTRS1985

Formulation/cure technology for ultrahigh molecular weight silphenylene-siloxane polymers

Molecular weights above one million were achieved for methylvinylsilphenylene-siloxane terpolymers using a two-stage polymerization technique which was successfully scaled up to 200 grams. The resulting polymer was vulcanized by two different formulations and compared to an identically formulated commercial methylvinyl silicone on the basis of ultimate strength, Young's modulus, percent elongation at failure, and tear strength. Relative thermal/oxidative stabilities of the elastomers were assessed by gradient and isothermal thermogravimetric analyses performed in both air and nitrogen. The experimental elastomer exhibited enhanced thermal/oxidative stability and possed equivalent or superior mechanical properties. The effect of variations in prepolymer molecular weight on mechanical properties was also investigated.

Hundley, N. H.↗

NASA NTRS1984

Mechanical property measurements of plasma-sprayed thermal-barrier coatings subjected to oxidation

Techniques have been developed for measuring the tensile properties of plasma-sprayed coatings which are used in thermal barrier applications. The measurements have included the average Young's modulus, bond strength and elongation at failure. The oxidation behavior of the bond coat plays an important role in the integrity and adhesion of plasma-sprayed thermal barrier coatings. This work studies the nature of the high temperature degradation on the mechanical properties of the coating. Furnace tests have been carried out on U-700 alloy with bond coats of NiCrAlY or NiCrAlZr and an overlay of ZrO2-8 percent Y2O3. Weight gain measurements on the coatings have been examined with relation to the adhesion strength and failure observations. The results from an initial study are reported in this work.

Berndt, C. C.↗

NASA NTRS1985

Mars - Thickness of the lithosphere from the tectonic response to volcanic loads

The response to loading of the elastic lithosphere of Mars by seven large volcanic features is estimated based on the hypothesis of a flexural origin for a definable set of load-concentric graben. From the locations of such graben, or from their absence, the lithospheric thickness and flexural rigidity are inferred. For the Tharsis montes, Alba Patera, and Elysium Mons, elastic lithospheric thicknesses at the time of loading range from 20 to 50 km, assuming a Young's modulus of a trillion dyn/sq cm. The thickness exceeded 120 km beneath Olympus Mons and Isidis Planitia. The corresponding ranges in flexural rigidity are approximately 10 to the 30th to 31st dyn cm and greater than 10 to the 32nd dyn cm, respectively. These results indicate a local thinning of the lithosphere beneath portions of the central regions of the Tharsis and Elysium volcanic provinces at the time of loading-induced fracturing.

Comer, R. P.↗

NASA NTRS1987

Design study of advanced model support systems for the National Transonic Facility (NTF)

It has long been recognized that the sting (or support system) is a very critical part of the model system. The designer is frequently faced with the tradeoff of minimizing sting size, thereby compromising facility and model safety, against a larger sting and the subsequent problems of sting interference effects. In the NASA Langley Research Center National Transonic Facility (NTF), this problem is accentuated by the severe environment of high pressure/low temperature, designed into the facility to provide the desired high Reynolds number. Compromises in the configuration geometry and/or limiting the test envelope are therefore contrary to the purposes and goals of the NTF and are unacceptable. The results of an investigation aimed at improvements of 25% in both strength and Young's modulus of elasticity as compared to high strength cryogenically acceptable steels currently being used are presented. Various materials or combinations of materials were studied along with different design approaches. Design concepts were developed which included conventional material stings, advanced composites, and hybrid configurations. Candidate configurations are recommended.

Source record↗