Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yield strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

3D Printed Ceramic Reinforced Polymer Composites Microstructure and Mechanical Properties

In Fused Filament Fabrication (FFF) 3D printing a part is made by extruding material layer by layer. Benefits of FFF are the ability to print complex shapes quickly and at a lower cost compared to other manufacturing methods. In this work, filaments composed of either silicon carbide (SiC) or zirconium silicate ceramic particulates in a polylactic-acid (PLA) matrix were used to print specimens for microstructural analysis and mechanical testing. Pure PLA samples were also printed and tested as a baseline for comparison. A Design of Experiments approach was used to test the interactions between three different parameters and their effect on ultimate strength, Young’s modulus, and yield strength. For compression test specimens, these parameters were infill percentage, number of shells, and print orientation angle. For tensile test specimens, the parameters were layer height, number of shells, and infill orientation angle. Pre- and post-compression test samples were evaluated by scanning electron microscopy for microstructural analysis. Infill percentage had the greatest effect on mechanical properties while number of shells and print orientation angle had minor effects. When changing the layer lines from perpendicular to parallel, relative to the loading direction, SiC-PLA had higher mechanical properties while pure PLA properties had decreased, and zirconium silicate-PLA had mix results.

Fused filament fabrication↗
NASA NTRS1990

Deformation and fracture of thin sheet aluminum-lithium alloys: The effect of cryogenic temperatures

The objective is to characterize the fracture behavior and to define the fracture mechanisms for new Al-Li-Cu alloys, with emphasis on the role of indium additions and cryogenic temperatures. Three alloys were investigated in rolled product form: 2090 baseline and 2090 + indium produced by Reynolds Metals, and commercial AA 2090-T81 produced by Alcoa. The experimental 2090 + In alloy exhibited increases in hardness and ultimate strength, but no change in tensile yield strength, compared to the baseline 2090 composition in the unstretched T6 condition. The reason for this behavior is not understood. Based on hardness and preliminary Kahn Tear fracture experiments, a nominally peak-aged condition was employed for detailed fracture studies. Crack initiation and growth fracture toughness were examined as a function of stress state and microstructure using J(delta a) methods applied to precracked compact tension specimens in the LT orientation. To date, J(delta a) experiments have been limited to 23 C. Alcoa 2090-T81 exhibited the highest toughness regardless of stress state. Fracture was accompanied by extensive delamination associated with high angle grain boundaries normal to the fatigue precrack surface and progressed microscopically by a transgranular shear mechanism. In contrast the two peak-aged Reynolds alloys had lower toughness and fracture was intersubgranular without substantial delamination. The influences of cryogenic temperature, microstructure, boundary precipitate structure, and deformation mode in governing the competing fracture mechanisms will be determined in future experiments. Results contribute to the development of predictive micromechanical models for fracture modes in Al-Li alloys, and to fracture resistant materials.

Wagner, John A.↗
NASA NTRS1990

Structure and properties during aging of an ultra-high strength Al-Cu-Li-Ag-Mg alloy

The structure and properties of the strengthening phases formed during aging in an Al-Cu-Li-Ag-Mg alloy (Weldalite 049) were elulcidated, by following the development of the microstructure by means of TEM. The results of observations showed that the Weldalite 049 alloy has a series of unusual and technologically useful combinations of mechanical properties in different aging conditions, such as natural aging without prior cold work to produce high strengths, a reversion temper of lower yield strength and unusually high ductility, a room temperature reaging of the reversion temper eventually leading to the original T4 hardness, and ultrahigh-strength T6 properties.

Gayle, Frank W.↗
NASA NTRS1938

The Crinkling Strength and the Bending Strength of Round Aircraft Tubing

The upper limit of the column strength of structural members composed of thin material is the maximum axial stress such members can carry when short enough to fail locally, by crinkling. This stress is a function of the mechanical properties of the material and of the geometrical shape of the cross section. The bending strength, as measured by the modulus of rupture, of structural members is also a function of these same variables. Tests were made of round tubes of chromium-molybdenum steel and of duralumin to determine the crinkling strengths and the bending strengths in terms of the specified yield strength and the ratio of diameter to thickness. Empirical formulas are given relating these quantities.

Osgood, William R↗
NASA NTRS1994

Improved construction materials for polar regions using microcellular thermoplastic foams

Microcellular polymer foams (MCF) are thermoplastic foams with very small cell diameters, less than 10 microns, and very large cell densities, 10(exp 9) to 10(exp 15) cells per cubic centimeter of unfoamed material. The concept of foaming polymers with microcellular voids was conceived to reduce the amount of material used for mass-produced items without compromising the mechanical properties. The reasoning behind this concept was that if voids smaller than the critical flaw size pre-existing in polymers were introduced into the matrix, they would not affect the overall strength of the product. MCF polycarbonate (PC), polystyrene (PS), and polyvinyl chloride (PVC) were examined to determine the effects of the microstructure towards the mechanical properties of the materials at room and arctic temperatures. Batch process parameters were discovered for these materials and foamed samples of three densities were produced for each material. To quantify the toughness and strength of these polymers, the tensile yield strength, tensile toughness, and impact resistance were measured at room and arctic temperatures. The feasibility of MCF polymers has been demonstrated by the consistent and repeatable MCF microstructures formed, but the improvements in the mechanical properties were not conclusive. Therefore the usefulness of the MCF polymers to replace other materials in arctic environments is questionable.

Cunningham, Daniel J.↗
NASA NTRS1988

Improved silicon carbide for advanced heat engines

This is the third annual technical report for the program entitled, Improved Silicon Carbide for Advanced Heat Engines, for the period February 16, 1987 to February 15, 1988. The objective of the original program was the development of high strength, high reliability silicon carbide parts with complex shapes suitable for use in advanced heat engines. Injection molding is the forming method selected for the program because it is capable of forming complex parts adaptable for mass production on an economically sound basis. The goals of the revised program are to reach a Weibull characteristic strength of 550 MPa (80 ksi) and a Weibull modulus of 16 for bars tested in 4-point loading. Two tasks are discussed: Task 1 which involves materials and process improvements, and Task 2 which is a MOR bar matrix to improve strength and reliability. Many statistically designed experiments were completed under task 1 which improved the composition of the batches, the mixing of the powders, the sinter and anneal cycles. The best results were obtained by an attritor mixing process which yielded strengths in excess of 550 MPa (80 ksi) and an individual Weibull modulus of 16.8 for a 9-sample group. Strengths measured at 1200 and 1400 C were equal to the room temperature strength. Annealing of machined test bars significantly improved the strength. Molding yields were measured and flaw distributions were observed to follow a Poisson process. The second iteration of the Task 2 matrix experiment is described.

Whalen, Thomas J.↗
NASA NTRS1976

Fractography of the high temperature hydrogen attack of a medium carbon steel

Results are reported for an experimental study of the microscopic fracture processes associated with hydrogen attack of a commercially produced plain carbon steel in a well-controlled high-temperature hydrogen environment of high purity. In the experiments, sheet samples were exposed to laboratory-grade hydrogen at a pressure of 3.5 MN/sq m and a temperature of 575 C. The fractography of gas-filled fissures and failed tension specimens is analyzed in an effort to identify any predominant microstructural defect associated with fissure formation, the prevalent modes of fracture, and the contribution of gas-filled fissures to the overall failure process. It is found that the tensile properties of the examined steel were significantly degraded after as few as 136 hr of exposure to a high-purity hydrogen atmosphere at 575 C; that the yield strength, ultimate strength, and elongation at fracture were all reduced progressively with increasing exposure time; and that the yield and ultimate strengths were reduced more than 40% after 408 hr while elongation was reduced to less than 2%.

Nelson, H. G.↗
NASA NTRS1989

Mechanisms controlling fatigue damage development in continuous fiber reinforced metal matrix composites

Damage in continuous fiber reinforced metal matrix composite materials can be quite complex since there are a number of different constituents (fiber, matrix, and the fiber/matrix interface) that can fail. Multidirectional lay-ups have an even greater number of possible damage orientations and mechanisms. Based on the simplifying assumption of equivalent constituent strain states in the absence of damage, a strain based failure criteria may be applied to determine when and where initial damage will occur. Based on the relative strain to fatigue failure of the fiber and matrix, the possible damage mechanisms of an MMC can be grouped into three categories: (1) matrix dominated, (2) fiber dominated, and (3) self-similar damage growth. A fourth type of damage development, fiber/matrix interface failure, is dependent on the relative strength of the fiber/matrix interface and the matrix yield strength. These four types of damage are discussed and illustrated by examples.

Johnson, W. S.↗
NASA NTRS1987

Advanced powder metallurgy aluminum alloys via rapid solidification technology, phase 2

Marko's rapid solidification technology was applied to processing high strength aluminum alloys. Four classes of alloys, namely, Al-Li based (class 1), 2124 type (class 2), high temperature Al-Fe-Mo (class 3), and PM X7091 type (class 4) alloy, were produced as melt-spun ribbons. The ribbons were pulverized, cold compacted, hot-degassed, and consolidated through single or double stage extrusion. The mechanical properties of all four classes of alloys were measured at room and elevated temperatures and their microstructures were investigated optically and through electron microscopy. The microstructure of class 1 Al-Li-Mg alloy was predominantly unrecrystallized due to Zr addition. Yield strengths to the order of 50 Ksi were obtained, but tensile elongation in most cases remained below 2 percent. The class 2 alloys were modified composition of 2124 aluminum alloy, through addition of 0.6 weight percent Zr and 1 weight percent Ni. Nickel addition gave rise to a fine dispersion of intermetallic particles resisting coarsening during elevated temperature exposure. The class 2 alloy showed good combination of tensile strength and ductility and retained high strength after 1000 hour exposure at 177 C. The class 3 Al-Fe-Mo alloy showed high strength and good ductility both at room and high temperatures. The yield and tensile strength of class 4 alloy exceeded those of the commercial 7075 aluminum alloy.

Ray, Ranjan↗
NASA NTRS1993

The effects of alloy purity on the mechanical behavior of soft oriented NiAl single crystals

Preliminary results of the effects of alloy purity on the mechanical properties of NiAl single crystals are presented. Two stoichiometric NiAl single crystals with different impurity contents were studied. It is concluded that reductions in the interstitial and substitutional levels cause reduced yield strengths in NiAl. Heat treatment also results in reduced yield and flow stresses in both CP-NiAl and Hp-NiAl which are considered to be due to a reduction in the concentration of thermal vacancies due to vacancy coalescence during heat treatment.

Weaver, M. L.↗
NASA NTRS2005

Alloy NASA-HR-1

NASA-HR-1 is a high-strength Fe-Ni-base superalloy that resists high-pressure hydrogen environment embrittlement (HEE), oxidation, and corrosion. Originally derived from JBK-75, NASA-HR-1 has exceptional HEE resistance that can be attributed to its gamma-matrix and eta-free (Ni3Ti) grain boundaries. The chemistry was formulated using a design approach capable of accounting for the simultaneous effects of several alloy additions. This approach included: (1) Systematically modifying gamma-matrix compositions based on JBK-75; (2) Increasing gamma (Ni3(Al,Ti)) volume fraction and adding gamma-matrix strengthening elements to obtain higher strength; and (3) Obtaining precipitate-free grain boundaries. The most outstanding attribute of NASA-HR-1 is its ability to resist HEE while showing much improved strength. NASA-HR-1 has approximately 25% higher yield strength than JXK-75 and exhibits tensile elongation of more than 20% with no ductility loss in a hydrogen environment at 5 ksi, an achievement unparalleled by any other commercially available alloy. Its Cr and Ni contents provide exceptional resistance to environments that promote oxidation and corrosion. Microstructural stability was maintained by improved solid solubility of the gamma-matrix, along with the addition of alloying elements to retard eta (Ni3Ti) precipitation. NASA-HR-1 represents a new system that greatly extends the compositional ranges of existing HEE-resistant Fe-Ni-base superalloys.

Chen, Po-Shou↗
NASA NTRS1993

Alloys For Corrosive, Hydrogen-Rich Environments

"NASA-23" denotes class of alloys resisting both embrittlement by hydrogen and corrosion. Weldable and castable and formed by such standard processes as rolling, forging, and wire drawing. Heat-treated to obtain desired combinations of strength and ductility in ranges of 100 to 180 kpsi yield strength, 120 to 200 kpsi ultimate tensile strength, and 10 to 30 percent elongation at break. Used in place of most common aerospace structural alloy, Inconel(R) 718.

Mcpherson, William B.↗
NASA NTRS1979

Transverse and longitudinal tensile properties at 760 C of several oxide dispersion strenghened nickel-base alloys

The transverse and longitudinal tensile properties of the oxide dispersion strengthened nickel base alloys MA-793, MA-754, MA-755E, and MA-6000E were determined at 760 C. Transverse tensile strengths were comparable to longitudinal strengths. Transverse ductility levels generally were less than two percent elongation. Both tensile and yield strengths increased with increasing strain rate over the range 0.001 to 0.05 per second. Ductility was not strain rate sensitive, but related to grain size and grain aspect ratio. The fracture mode of most alloys changed from transgranular for longitudinally oriented specimens to intergranular for transverse specimens. Transverse properties of DM MAR M-200 + Hf were also determined for comparison.

Anglin, A. E., Jr.↗
NASA NTRS1979

Transverse and longitudinal tensile properties at 760 C of several oxide dispersion strengthened nickel-base alloys

The transverse and longitudinal tensile properties of the oxide dispersion strengthened nickel-base alloys were determined at 760 C. The alloys with small amounts of gamma prime have strength levels suitable for turbine vane applications, while other highly alloyed, gamma prime strengthened superalloys have strengths typical of turbine blade materials. These alloys were produced by mechanical alloying and extrusion and the turbine blade alloys were also directionally recrystallized. Resultant grain aspect ratios varied from 1:1 to over 20:1. Longitudinal tensile strengths ranged from 285 to 1175 MPa, while longitudinal elongations were in excess of 4 percent for all alloys. Transverse tensile strengths were comparable to longitudinal strengths, but transverse ductility levels were generally less than 2 percent elongation. Tensile and yield strengths increased with increasing strain rate over the range 0.001 to 0.05 per second. Ductility in both orientations was not strain rate sensitive but could be related to grain size and grain aspect ratio.

Anglin, A. E., Jr.↗
NASA NTRS1974

The resistance to embrittlement by a hydrogen environment of selected high strength iron-manganese base alloys

Fe-16Mn and Fe-25Mn base alloys, which had been cold worked to yield strength levels of 201 and 178 KSI, were resistant to degradation of mechanical properties in a one atmosphere hydrogen environment at ambient temperature under the loading conditions employed in this investigation. Transmission electron microscopy established that bands of epsilon phase martensite and fcc mechanical twins were formed throughout the fcc matrix when these alloys were cold worked. In the cold worked alloys a high density of crystal defects were observed associated with both types of strain induced structures, which should contribute significantly to the strengthening of these alloys. High strength iron base alloys can be produced which appear to have some resistance to degradation of mechanical properties in a hydrogen environment under certain conditions.

Benson, R. B., Jr.↗
NASA NTRS1991

The role of equiaxed particles on the yield stress of composites

Possible explanations are investigated for the yield strength enhancement of discontinuously reinforced Al alloy matrix MMCs, for the case of low temperature yield behavior where deformation occurs by dislocation slide. The Al alloys contain 0.1-10 micron diameter equiaxed particle discontinuous reinforcements of TiB2, Al2O3, and TiC. Attention is given to a single dislocation-particle interaction model, and both dislocation pile-up and forest-hardening multiple-dislocation particle interaction models.

Aikin, R. M., Jr.↗