Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wave loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effects of Strain Gauge Coatings on Water Intrusion in Submerged Composite Coupon Testing

Marine energy structures are typically made using composite materials and are repeatedly loaded by currents and waves. Submersion and repeated loading lead to two environmental effects: moisture intrusion and mechanical fatigue. To understand their combined effects, submerged fatigue testing can be used. Submerged fatigue testing often requires submerged instrumentation to validate component manufacturing methods and models. Strain measurements are critical for understanding marine energy component loads. One common method for measuring strain is by using foil strain gauges, but the durability of strain gauges in submerged fatigue conditions is not well-understood. To increase strain gauge durability and protection from contamination, delamination, and water intrusion, strain gauge coatings may be applied over strain gauges and wire connections. In this study, strain gauges were adhered to composite coupons, coated, and mechanically tested in a water tank. Cycles to composite failure, cycles to strain gauge failure (SGF), strains, and SGF modes were used to measure the effects of strain gauge coatings on composite fatigue life and strain gauge durability. The coatings did not have significant effects on composite fatigue life or strain gauge durability. The methods developed and measurements taken at the coupon scale in this study will be used to inform methods and designs for subsequent submerged subcomponent testing, full-scale testing, and standards development. The benefits of designing marine energy structures to informed standards and designs are decreased lifetime costs and increased reliability and energy production, ultimately leading to a sustainable and low-carbon energy system.

composite materials↗
DOE OSTI2024

Design of a Three-Layer Impactor for Material Strength Measurements at Multi-Megabar Pressures

Off-Hugoniot loading methods for dynamic compression have been a topic of interest for many years as a means of accessing high pressures without melting a material. Simulations and an initial test experiment of a three-layer gas-gun impactor suitable for use in measuring dynamic material strength at multi-megabar pressures are described. As shown through ARES hydrocode simulations, an impactor consisting of a low-, medium-, and high-impedance material, such as TPX, Al, and Ta or Pt, can produce a quasi-isentropic loading path up to 4.6 Mbar pressure with a low homologous temperature (T/T melt = 0.1–0.25). These impactors can also be tailored to create a pressure drive suitable for a Lagrangian sound speed experiment. Simulated in-situ velocities were analyzed to determine the change in calculated strength due to non-uniformity in the impactor, which provides a measure of error sensitivity. An initial test of a three-layer projectile onto a flat target at 4.4 km/s impact velocity is reported. Finally, while the impactor incurred some delamination during firing, the measured sample/window interface velocity generally agrees with the simulated peak velocity and subsequent release, indicating the feasibility of this approach for measuring material strength.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Graph Neural Networks for Surrogate Modeling of Offshore Floating Platforms

Floating offshore wind turbines (FOWTs) present an significant opportunity to increase renewable energy generation. However, significant challenges remain before FOWTs can be widely commercialized and deployed. In particular, hydrodynamic loading on the platforms can stress the overall structure, damage the mooring systems, and impact power generation. Studying these loads is difficult and often relies on computationally expensive models or experiments. In this work, we explore the use of graph neural networks (GNNs) to construct flexible, data-driven surrogates for hydrodynamic loads on platforms. We leverage the natural graph-like structure of offshore wind platform designs to enable the GNN model to learn to approximate the loads for different wave conditions and structural designs. We demonstrate potential uses for the surrogate by performing parameter sweeps and ridge analysis on the trained model to identify the impacts of different wave and structural features on the loads.

floating offshore wind turbines↗
NASA NTRS1976

Influence of specimen boundary on the dynamic stress intensity factor

The problem to be considered is the sudden appearance of a flaw or crack in a strip of material of finite height subjected to tensile loading. Stress waves are generated within the strip and are reflected from boundary to boundary. Of interest is the maximum value of the dynamic stress intensity factor at a given instance of time as the strip height to crack length ratio is varied.

Chen, E. P.↗
NASA NTRS1982

Study of aerodynamic technology for single-cruise-engine V/STOL fighter/attack aircraft

Conceptual designs and analyses were conducted on two V/STOL supersonic fighter/attack aircraft. These aircraft feature low footprint temperature and pressure thrust augmenting ejectors in the wings for vertical lift, combined with a low wing loading, low wave drag airframe for outstanding cruise and supersonic performance. Aerodynamic, propulsion, performance, and mass properties were determined and are presented for each aircraft. Aerodynamic and Aero/Propulsion characteristics having the most significant effect on the success of the up and away flight mode were identified, and the certainty with which they could be predicted was defined. A wind tunnel model and test program are recommended to resolve the identified uncertainties.

Mark, L.↗
NASA NTRS1990

Spacecraft observations of the interaction of active comets with the solar wind

Six spacecraft encountered two comets during 1985 and 1986, obtaining a wealth of data relative to the plasma processes at work in the interaction of an active comet with the solar wind. A review of what space plasma scientists have learned from these data and of their interpretations is presented. The interaction process begins millions of kilometers from the nucleus where the solar wind first picks up cometary ions that slow down the wind and causes the interplanetary magnetic field to pile up and drape around the comet's ionosphere. Thus the geometry of a comet's plasma tail is defined by this draped field. At Halley the Giotto spacecraft noted a well-defined boundary separating the mixture of solar wind and cometary plasmas and the interplanetary magnetic field from the free-field, almost pure cometary plasma in the inner coma. Additional unexpected features in the inner coma were a flux of fast 'granddaughter' ions and high densities of negative ions. Further details covering pickup ions and plasma waves, mass loading, bow shock, energetic particles, the cometosheath, the ionopause, the plasma tail, and the field-free region are provided.

Neugebauer, M.↗
NASA NTRS2016

Aerodynamic Modeling of Transonic Aircraft Using Vortex Lattice Coupled with Transonic Small Disturbance for Conceptual Design

The need to rapidly scan large design spaces during conceptual design calls for computationally inexpensive tools such as the vortex lattice method (VLM). Although some VLM tools, such as Vorview have been extended to model fully-supersonic flow, VLM solutions are typically limited to inviscid, subcritical flow regimes. Many transport aircraft operate at transonic speeds, which limits the applicability of VLM for such applications. This paper presents a novel approach to correct three-dimensional VLM through coupling of two-dimensional transonic small disturbance (TSD) solutions along the span of an aircraft wing in order to accurately predict transonic aerodynamic loading and wave drag for transport aircraft. The approach is extended to predict flow separation and capture the attenuation of aerodynamic forces due to boundary layer viscosity by coupling the TSD solver with an integral boundary layer (IBL) model. The modeling framework is applied to the NASA General Transport Model (GTM) integrated with a novel control surface known as the Variable Camber Continuous Trailing Edge Flap (VCCTEF).

Transonic Small Disturbance↗
NASA NTRS1973

BUCLAP2: A computer program for instability analysis of laminated long plates subjected to combined inplane loads

This program description document describes the program structure and the design details of a CDC 6600 FORTRAN 4 digital computer program, BUCLAP2, which uses minimum energy principles to do an elastic stability analysis of curved and flat laminated rectangular long plates subjected to combined inplane normal and shear loads. Given the geometry, the material properties, and slected boundary conditions for the plate element, the program calculates the minimum buckling load for various wave lengths. The two parallel ends of the program calculates the minimum buckling load for various wave lengths. The two parallel ends of the long plate must be simply supported and arbitrary elastic boundary conditions may be imposed along either one or both external longitudinal sides. For guide to program use, see

Halstead, D. W.↗
NASA NTRS1992

Postbuckling failure of composite plates with holes

This paper summarizes a study focused on understanding the failure mechanisms present in a plate with a centrally located circular hole loaded inplane into the postbuckling range of deflections. The study was numerical and experimental in nature and had as a goal the a priori prediction of failure using existing failure data from several sources, together with a stress analysis. The maximum stress failure criterion was used to predict failure and both intra- and interlaminar stresses were considered. Four laminates were considered. The phenomenon of modal interaction, or the jumping from one deformed configuration to another, is discussed. With this jumping, the plate configuration may change from one half-wave in the loading direction to two half-waves in the loading direction. The study concludes that the failure in (+/-45/0/90)2s and (+/-45/2(2))2s laminates is due to fiber compression failure and is predictable. The failure load is, for the most part, independent of response configuration. The (+/-45/0/(6))s laminate fails due to interlaminar shear along the simple support, while the response and failure of the (+/-45)4s laminate is governed to a large degree by material nonlinearities and progressive failure.

Lee, H. H.↗
DOE OSTI2022

Hydrodynamics and Load Shedding Behavior of a Variable-Geometry Oscillating Surge Wave Energy Converter (OSWEC)

In order to improve their long-term viability, wave energy converters (WECs) need to be able to shed loads when a threshold wave condition is exceeded. As shown by Tom et al. (2016) [1], provision of adjustable flaps within the body of an oscillating surge wave energy converter (OSWEC) allows wave energy to pass through the device. A control system may then be able to open and close the flaps when waves approaching the device exceed preset thresholds. The variable-geometry OSWEC (VG-OSWEC) concept studied in this paper is a bottom-hinged, rectangular wave paddle with five flaps of elliptical cross-section embedded into the face of the paddle. System ID tests were conducted on this VG-OSWEC device at a 1:14 scale in a wave basin. Free decay tests showed that the damping was distinctly nonlinear when the flaps were fully open, and the natural frequency increased by 40% when compared with the flaps in a fully closed configuration. Tests with regular wave conditions were used to develop the response amplitude operator for the rotational motion about the hinge. These response amplitude operator results when compared with numerical simulations run using WEC-Sim/WAMIT and ANSYS AQWA, show strong agreement with the flap open and closed conditions. The regular-wave condition measurements also show that the wave excitation moment about the hinge was reduced by up to 60% when the flaps were fully open. The experiments serve to demonstrate the potential of the variable geometry design to shed loads and survive harsh ocean environments.

load shedding↗
NASA NTRS2007

Orbiter Gap Filler Bending Model for Re-entry

Pressure loads on a protruding gap filler during an Orbiter reentry are investigated to evaluate the likelihood of extraction due to pressure loads, and to ascertain how much bending will be induced by re-entry pressure loads. Oblique shock wave theory is utilized to develop a representation of the pressure loads induced on a gap filler for the ISSHVFW trajectory, representative of a heavy weight ISS return. A free body diagram is utilized to react the forces induced by the pressure forces. Preliminary results developed using these methods demonstrate that pressure loads, alone, are not likely causes of gap filler extraction during reentry. Assessment of the amount a gap filler will bend over is presented. Implications of gap filler bending during re-entry include possible mitigation of early boundary layer transition concerns, uncertainty in ground based measurement of protruding gap fillers from historical Orbiter flight history, and uncertainty in the use of Orbiter gap fillers for boundary layer prediction calibration. Authors will be added to the author list as appropriate.

Campbell, Charles H.↗
NASA NTRS1980

Unsteady aerodynamics of conventional and supercritical airfoils

The unsteady aerodynamics of a conventional and a supercritical airfoil are compared by examining measured chordwise unsteady pressure time-histories from four selected flow conditions. Although an oscillating supercritical airfoil excites more harmonics, the strength of the airfoil's shock wave is the more important parameter governing the complexity of the unsteady flow. Whether they are conventional or supercritical, airfoils that support weak shock waves induce unsteady loads that are qualitatively predictable with classical theories; flows with strong shock waves are sensitive to details of the shock-wave and boundary-layer interaction and cannot be adequately predicted.

Davis, S. S.↗
DOE OSTI2021

Investigation of Nonlinear Difference-Frequency Wave Excitation on a Semisubmersible Offshore-Wind Platform with Bichromatic-Wave CFD Simulations: Preprint

The natural surge and pitch frequencies of semisubmersible offshore wind platforms are typically designed to be below the wave frequencies to avoid direct excitation. However, surge or pitch resonance can be excited by the nonlinear low-frequency loads generated by irregular incident waves. Second-order potential-flow models with added Morison drag have been found to underpredict this low-frequency excitation and response. As part of the OC6 project, Computational Fluid Dynamics (CFD) simulations were performed to enable a better understanding of the low-frequency loads and the limitations of lower-fidelity models. The focus of the current paper is to set up a computationally cost-effective CFD simulation of a fixed semisubmersible platform to investigate nonlinear difference-frequency loads and establish the corresponding uncertainty in the results. Due to the high computing cost, CFD simulations of irregular waves can be challenging. Instead, simulations were performed with bichromatic waves having a shorter repeat period. A preliminary comparison with Quadratic Transfer Functions from second-order potential-flow theory shows that CFD models consistently predict higher nonlinear wave loads at the difference frequency, likely due to flow separation and viscous drag not accounted for in potential-flow theory.

2nd order↗
DOE OSTI2022

2.1.2.403 - Fatigue and Structural Load Analysis and Control for Variable-Geometry Wave Energy Converters (VGWECs)

The VGWEC project will generate and disseminate the foundational knowledge enabling a paradigm shift in the design of wave energy converters (WECs) by adding a geometry control option on top of power-take-off load control. The variable-geometry modules (VGMs) provide control over a WEC's hydrodynamics that can emphasize power absorption or load shedding. Additional load shedding provided by the VGMs is expected to reduce the device structural mass and extend the sea state operating envelope, by limiting peak loading, both contributing towards reducing levelized cost of energy (LCOE) estimates.

hydrodynamic↗
DOE OSTI2023

Sensitivity analysis of numerical modeling input parameters on floating offshore wind turbine loads

Abstract. Floating wind turbines must withstand a unique and challenging set of loads from the wind and ocean environment. To de-risk development, accurate predictions of these loads are necessary. Uncertainty in modeling predictions leads to larger required safety factors, increasing project costs and the levelized cost of energy. Complex aero-hydro-elastic modeling tools use many input parameters to represent the wind, waves, current, aerodynamic loads, hydrodynamic loads, and structural properties. It is helpful to understand which of these parameters ultimately drives a design. In this work, an ultimate and fatigue-proxy load sensitivity analysis was performed with 35 different input parameters, using an elementary effects approach to identify the most influential parameters for a case study involving the National Renewable Energy Laboratory (NREL) 5 MW baseline wind turbine atop the OC4-DeepCwind semisubmersible during normal operation. The importance of each parameter was evaluated using 14 response quantities of interest across three operational wind speed conditions. The study concludes that turbulent wind velocity standard deviation is the parameter with the strongest sensitivity; this value is important not just for turbine loads, but also for the global system response. The system center of mass in the wind direction is found to have the highest impact on the system rotation and tower loads. The current velocity is found to be the most dominating parameter for the system global motion and consequently the mooring loads. All tested wind turbulence parameters in addition to the standard deviation are also found to be influential. Wave characteristics are influential for some fatigue-proxy loading but do not significantly impact the extreme ultimate loads in these operational load cases. The required number of random seeds for stochastic environmental conditions is considered to ensure that the sensitivities are due to the input parameters and not due to the seed. The required number of analysis points in the parameter space is identified so that the conclusions represent a global sensitivity. The results are specific to the platform, turbine, and choice of parameter ranges, but the demonstrated approach can be applied widely to guide focus in parameter uncertainty.

17 WIND ENERGY↗
DOE OSTI2022

The Role of Regional Connections in Planning for Future Power System Operations Under Climate Extremes

Identifying the sensitivity of future power systems to climate extremes must consider the concurrent effects of changing climate and evolving power systems. We investigated the sensitivity of a Western U.S. power system to isolated and combined heat and drought when it has low (5%) and moderate (31%) variable renewable energy shares, representing historic and future systems. We used an electricity operational model combined with a model of historically extreme drought (for hydropower and freshwater-reliant thermoelectric generators) over the Western U.S. and a synthetic, regionally extreme heat event in Southern California (for thermoelectric generators and electricity load). We found that the drought has the highest impact on summertime production cost (+10% to +12%), while temperature-based deratings have minimal effect (at most +1%). The Southern California heat wave scenario impacting load increases summertime regional net imports to Southern California by 10-14%, while the drought decreases them by 6-12%. Combined heat and drought conditions have a moderate effect on imports to Southern California (-2%) in the historic system and a stronger effect (+8%) in the future system. Southern California dependence on other regions decreases in the summertime with the moderate increase in variable renewable energy (-34% imports), but hourly peak regional imports are maintained under those infrastructure changes. By combining synthetic and historically driven conditions to test two infrastructures, we consolidate the importance of considering compounded heat wave and drought in planning studies and suggest that region-to-region energy transfers during peak periods are key to optimal operations under climate extremes.

24 POWER TRANSMISSION AND DISTRIBUTION↗