SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A study was initiated at NASA's Wallops Flight Facility to enhance available information on U.S. radiosonde temperature measurement accuracy and precision. A method utilizing three thermistors with different reflective coatings is shown to be satisfactory for determining corrections to the standard U.S. radiosonde instrument.
For more than two decades, the staff of the Space Physics Research Laboratory (SPRL) has collaborated with the Goddard Space Flight Center (GSFC) in the design and implementation of Langmuir probes (LP). This program of probe development under the direction of Larry Brace of GSFC has evolved methodically with innovations to: improve measurement precision, increase the speed of measurement, and reduce the weight, size, power consumption and data rate of the instrument. Under contract NAG5-419 these improvements were implemented and are what characterize the Advanced Langmuir Probe (ALP). Using data from the Langmuir Probe on the Pioneer Venus Orbiter, Brace and Walter Hoegy of GSFC demonstrated a novel method of monitoring the solar extreme ultraviolet (EUV) flux. This led to the idea of developing a sensor similar to a Langmuir probe specifically designed to measure solar EUV (SEUV) that uses a similar electronics package. Under this contract, a combined instrument package of the ALP and SEUV sensor was to be designed, constructed, and laboratory tested. Finally the instrument was to be flight tested as part of sounding rocket experiment to acquire the necessary data to validate this method for possible use in future earth and planetary aeronomy missions. The primary purpose of this contract was to develop the electronics hardware and software for this instrument, since the actual sensors were suppied by GSFC. Due to budget constraints, only a flight model was constructed. These electronics were tested and calibrated in the laboratory, and then the instrument was integrated into the rocket payload at Wallops Flight Facility where it underwent environmental testing. After instrument recalibration at SPRL, the payload was reintegrated and launched from the Poker Flat Research Range near Fairbanks Alaska. The payload was successfully recovered and after refurbishment underwent further testing and developing to improve its performance for future use.
Airborne radiometric measurements at frequencies near 92 GHz and 183 GHz were conducted over two precipitation events near Wallops Island, Virginia during February, 1986. The measured brightness temperatures are compared with those from calculations to estimate the snowfall and rainfall rates for both events. The estimated rates over water surface are within a factor of two of those derived from the concurrent measurements by the SPANDAR radar at the NASA Wallops Flight Facility. These estimated rates, however, suggest that both snowfall events are light and close to the threshold of radiometric detection especially over land surface. Observations of additional snowfall events with lower frequency channels are needed to demonstrate the approach and to account for cloud effects.
An algorithm has been developed to model the average return power waveforms available from general radar altimeter systems, such as the Multimode Airborne Radar Altimeter (MARA) system operated at NASA Goddard Space Flight Center - Wallops Flight Facility. The algorithm is based on a convolutional model comprised of three functions: the average flat surface impulse response (FSIR), the radar system point target response (PTR), and the height pdf of the specular points on the sea surface. The FSIR is modified to account for the asymmetric antenna beam used by the MARA system, and then certain properties of this modified SIR are exploited to obtain closed-form expressions that can be rapidly evaluated. An FFT convolution routine is used to further speed up the computations. The result is an algorithm that can be used to study the effects of pointing errors in surface measurements.
This Technical Memorandum provides extensive data on birdlife at Wallops Island, a mid-Atlantic barrier island, and home to NASA Wallops Flight Facility's launch range. Variation in the distribution and abundance of many species is considerable in this region, which is centered along the north-south axis of the Delmarva Peninsula. Data (date of occurrence and general abundance) and analysis of the Island's diverse habitat structure are provided. A total of 244 species of birds are recorded; a summary of the records are given in the Species Accounts and the Appendix.
During the fall of 1993, NASA sponsored a field program called the Convection And Moisture Experiment (CAMEX). The field effort focused on: convective storms in order to investigate their associated electrical properties, precipitation, and predictability, and atmospheric moisture studies. The data collected from the Multispectral Atmospheric Mapping Sensor (MAMS) onboard a NASA ER-2 aircraft which was deployed out of NASA/Wallops Flight Facility, Wallops Island, Virginia, from 11 Sep. through 7 Oct., 1993, is described.
The catastrophic balloon failure during the first half of the 1980's identified the need for a comprehensive and continuing balloon research and development (R&D) commitment by NASA. Technical understanding was lacking in many of the disciplines and processes associated with scientific ballooning. A comprehensive balloon R&D plan was developed in 1986 and implemented in 1987. The objectives were to develop the understanding of balloon system performance, limitations, and failure mechanisms. The program consisted of five major technical areas: structures, performance and analysis, materials, chemistry and processing, and quality control. Research activitites have been conducted at NASA/Goddard Space Flight Center (GSFC)-Wallops Flight Facility (WFF), other NASA centers and government facilities, universities, and the balloon manufacturers. Several new and increased capabilities and resources have resulted from this activity. The findings, capabilities, and plan of the balloon R&D program are presented.
Solid State Laser Initiated Ordnance (LIO) offers new technology having potential for enhanced safety, reduced costs, and improved operational efficiency. Concerns over the absence of programmatic applications of the technology, which has prevented acceptance by flight programs, should be abated since LIO has now been operationally implemented by the Laser Initiated Ordnance Sounding Rocket Demonstration (LOSRD) Program. The first launch of solid state laser diode LIO at the NASA Wallops Flight Facility (WFF) occurred on March 15, 1995 with all mission objectives accomplished. This project, Phase 3 of a series of three NASA Headquarters LIO demonstration initiatives, accomplished its objective by the flight of a dedicated, all-LIO sounding rocket mission using a two-stage Nike-Orion launch vehicle. LIO flight hardware, made by The Ensign-Bickford Company under NASA's first Cooperative Agreement with Profit Making Organizations, safely initiated three demanding pyrotechnic sequence events, namely, solid rocket motor ignition from the ground and in flight, and flight termination, i.e., as a Flight Termination System (FTS). A flight LIO system was designed, built, tested, and flown to support the objectives of quickly and inexpensively putting LIO through ground and flight operational paces. The hardware was fully qualified for this mission, including component testing as well as a full-scale system test. The launch accomplished all mission objectives in less than 11 months from proposal receipt. This paper concentrates on accomplishments of the ordnance aspects of the program and on the program's implementation and results. While this program does not generically qualify LIO for all applications, it demonstrated the safety, technical, and operational feasibility of those two most demanding applications, using an all solid state safe and arm system in critical flight applications.
The airborne Raman lidar recently completed a series of flight tests aboard a C-130 aircraft operated by the NASA Wallops Flight Facility. The Raman lidar is intended to make simultaneous remote measurements of methane, water vapor, temperature, and pressure. The principal purpose of the measurements is to aid in the investigation of polar phenomena related to the formation of ozone 'holes' by permitting the identification of the origin of air parcels using methane as a tracer.
Water vapor plays an important role in many atmospheric processes related to radiation, climate change, atmospheric dynamics, meteorology, the global hydrologic cycle, and atmospheric chemistry, and yet our knowledge of the global distribution of water vapor is very limited. The differential absorption lidar (DIAL) technique has the potential of providing needed high resolution water vapor measurements from aircraft and from space, and the Lidar Atmospheric Sensing Experiment (LASE) is a key step in the development of this capability. The LASE instrument is the first fully engineered, autonomous DIAL system, and it is designed to operate from a high-altitude aircraft (ER-2) and to make water vapor and aerosol profile measurements across the troposphere. The LASE system was flown from the NASA Wallops Flight Facility in a series of engineering flights during September 1994. This paper discusses the characteristics of the LASE system and presents the first LASE measurements of water vapor and aerosol profiles.
An airborne differential absorption lidar (DIAL) system has been developed at the NASA Langley Research Center for remote measurements of atmospheric water vapor (H2O) and aerosols. A solid-state alexandrite laser with a 1-pm linewidth and greater than 99.85% spectral purity was used as the on-line transmitter. Solid-state avalanche photodiode detector technology has replaced photomultiplier tubes in the receiver system, providing an average increase by a factor of 1.5-2.5 in the signal-to-noise ratio of the H2O measurement. By incorporating advanced diagnostic and data-acquisition instrumentation into other subsystems, we achieved additional improvements in system operational reliability and measurement accuracy. Laboratory spectroscopic measurements of H2O absorption-line parameters were performed to reduce the uncertainties in our knowledge of the absorption cross sections. Line-center H2O absorption cross sections were determined, with errors of 3-6%, for more than 120 lines in the 720-nm region. Flight tests of the system were conducted during 1989-1991 on the NASA Wallops Flight Facility Electra aircraft, and extensive intercomparison measurements were performed with dew-point hygrometers and H2O radiosondes. The H2O distributions measured with the DIAL system differed by less than 10% from the profiles determined with the in situ probes in a variety of atmospheric conditions.
A turbulent air motion measurement system (TAMMS) was integrated onboard the Lockheed 188 Electra airplane (designated NASA 429) based at the Wallops Flight Facility in support of the NASA role in global tropospheric research. The system provides air motion and turbulence measurements from an airborne platform which is capable of sampling tropospheric and planetary boundary-layer conditions. TAMMS consists of a gust probe with free-rotating vanes mounted on a 3.7-m epoxy-graphite composite nose boom, a high-resolution inertial navigation system (INS), and data acquisition system. A variation of the tower flyby method augmented with radar tracking was implemented for the calibration of static pressure position error and air temperature probe. Additional flight calibration maneuvers were performed remote from the tower in homogeneous atmospheric conditions. System hardware and instrumentation are described and the calibration procedures discussed. Calibration and flight results are presented to illustrate the overall ability of the system to determine the three-component ambient wind fields during straight and level flight conditions.
In early 1993, funding for the NUVIEWS experiment was initiated. The experiment was completed and delivered to Wallops Flight Facility in March 1996, where it has completed flight integration and testing successfully. We feel that the three year development time was too long by a year, and that the history deserves some explanation. The construction of four complete four-mirror telescope systems with unique multilayer coatings, superpolished aspheres, and four large-format, high-resolution microchannel-plate detectors required a substantial effort. Our original design included only three telescopes, but we added a fourth 18 months ago to ensure rejection of all potential contaminating line features. A six-month SMEX Definition study in 1994 required substantial efforts by key personnel. There was great synergy here: the four NUVIEWS detectors are prototypes for the SMEX UV-survey mission (JUNO). In 1993, the Principal Investigator C. Martin took a position at Caltech. The transition of the laboratory from Columbia to Caltech was unfortunately timed and led to more delays, including an additional laboratory move and calibration tank/clean room reconstruction. Following the May NUVIEWS launch, the laboratory move to Caltech will be complete.
Wake vortices from a C-130 airplane were observed at the NASA Wallops Flight Facility with a ground-based, monostatic C-band radar and an antenna-mounted boresight video camera. The airplane wake was viewed from a distance of approximately 1 km, and radar scanning was adjusted to cross a pair of marker smoke trails generated by the C-130. For each airplane pass, changes in radar reflectivity were calculated by subtracting the signal magnitudes during an initial clutter scan from the signal magnitudes during vortex-plus-clutter scans. The results showed both increases and decreases in reflectivity on and near the smoke trails in a characteristic sinusoidal pattern of heightened reflectivity in the center and lessened reflectivity at the sides. Reflectivity changes in either direction varied from -131 to -102 dBm(exp -1); the vortex-plus-clutter to noise ratio varied from 20 to 41 dB. The radar recordings lasted 2.5 min each; evidence of wake vortices was found for up to 2 min after the passage of the airplane. Ground and aircraft clutter were eliminated as possible sources of the disturbance by noting the occurrence of vortex signatures at different positions relative to the ground and the airplane. This work supports the feasibility of vortex detection by radar, and it is recommended that future radar vortex detection be done with Doppler systems.
This report documents a high risk, high pay-off experiment with the objective of detecting, for the first time, the presence of aircraft wake vortices in clear air using X-band Doppler radar. Field experiments were conducted in January 1995 at the Wallops Flight Facility (WFF) to demonstrate the capability of the 9.33 GHz (I=3 cm) radar, which was assembled using an existing nine-meter parabolic antenna reflector at VVTT and the receiver/transmitter from the NASA Airborne Windshear Radar-Program. A C-130-aircraft, equipped with wingtip smoke generators, created visually marked wake vortices, which were recorded by video cameras. A C-band radar also observed the wake vortices during detection attempts with the X-band radar. Rawinsonde data was used to calculate vertical soundings of wake vortex decay time, cross aircraft bearing wind speed, and water vapor mixing ratio for aircraft passes over the radar measurement range. This experiment was a pathfinder in predicting, in real time, the location and persistence of C-130 vortices, and in setting the flight path of the aircraft to optimize X-band radar measurement of the wake vortex core in real time. This experiment was conducted in support of the NASA Aircraft Vortex Spacing System (AVOSS).
This project has resulted in 4 launches from the White Sands Missile Range of our payload in different stages of development, on: (1) 4 May 1991 Flight 36.062; (2) 16 June 1993 Flight 36.101; (3) 1 April 1995 Flight 36.104; and (5) 28 October 1996 Flight 36.149. For each flight, the following activities were accomplished: (1) prepare the experiment, including replacement and upgrading of critical components, at the University of Michigan; (2) integrate the payload either at the Wallops Flight Facility; (3) perform final far-UV calibration of instrument; (4) perform final alignment, integration, and electrical checks at WSMR (5) launch payload from WSMR (6) check condition of recovered payload (7) perform post-flight calibration, if necessary and applicable; and (8) reduce and analyze flight data. A description of the instrument is presented, along with overviews of the results of the four flights. We are presently preparing the payload for the next flight in 1998/99.
Results are presented from topographic surveys of the Assateague Island National Seashore using recently developed Airborne Topographic Mapper (ATM) and kinematic Global Positioning System (GPS) technology. In November, 1995, and again in May, 1996, the NASA Arctic Ice Mapping (AIM) group from the Goddard Space Flight Center's Wallops Flight Facility conducted the topographic surveys as a part of technology enhancement activities prior to conducting missions to measure the elevation of extensive sections of the Greenland Ice Sheet as part of NASA's Global Climate Change program. Differences between overlapping portions of both surveys are compared for quality control. An independent assessment of the accuracy of the ATM survey is provided by comparison to surface surveys which were conducted using standard techniques. The goal of these projects is to mdke these measurements to an accuracy of +/- 10 cm. Differences between the fall 1995 and 1996 surveys provides an assessment of net changes in the beach morphology over an annual cycle.
The primary objective of this grant was to validate the modified CMOD4 wind speed algorithm used to invert RADARSAT data. We proposed to do the following: TASK 1: Participate in at least two underflights of RADARSAT (collecting backscatter measurements with the UMASS C-band and Ku-band scatterometers, CSCAT and KUSCAT. TASK 2: Process data gathered with CSCAT and KUSCAT into one kilometer along-track pixels with each pixel consisting of seventy-two five degree azimuth bins - each bin containing normalized radar cross section (NRCS) values for that particular azimuth angle and for each of the four incidence angles viewed by CSCAT and KUSCAT. Derive wind speed and direction estimates from each NRCS along-track pixel using CMOD4 and NSCAT models. TASK 3: Compare collocated CSCAT vertically polarized (VV) and RADARSAT horizontally polarized (HH) NRCS data and wind estimates, and based on the comparison, evaluate the performance of the modified CMOD4 wind speed algorithm to invert RADARSAT NRCS measurements. The first two tasks were completed. The third task is still on-going since the RADARSAT data for the underflights has not been released to the University of Massachusetts. We expect that the RADARSAT data will become available in the next few months, and we will complete the third task in a promptly manner once the data has been received. Below the missions flown and the data collected are summarized. Two missions, based out of the NASA Wallops Flight Facility, were flown. The first flight was on 21 September 1997 and the second on 24 September 1997. The time for each mission was approximately 2 hours. Figure 1 plots the flight tracks and marks the location of the NOAA buoys that were in the vicinity.