Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vibrational analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Finite-Element Vibration Analysis and Modal Testing of Graphite Epoxy Tubes and Correlation Between the Data

Structural materials in the form of graphite epoxy composites with embedded rubber layers are being used to reduce vibrations in rocket motor tubes. Four filament-wound, graphite epoxy tubes were studied to evaluate the effects of the rubber layer on the modal parameters (natural vibration frequencies, damping, and mode shapes). Tube 1 contained six alternating layers of 30-degree helical wraps and 90-degree hoop wraps. Tube 2 was identical to tube 1 with the addition of an embedded 0.030-inch-thick rubber layer. Tubes 3 and 4 were identical to tubes 1 and 2, respectively, with the addition of a Textron Kelpoxy elastomer. This report compares experimental modal parameters obtained by impact testing with analytical modal parameters obtained by NASTRAN finite-element analysis. Four test modes of tube 1 and five test modes of tube 3 correlate highly with corresponding analytical predictions. Unsatisfactory correlation of test and analysis results occurred for tubes 2 and 4 and these comparisons are not shown. Work is underway to improve the analytical models of these tubes. Test results clearly show that the embedded rubber layers significantly increase structural modal damping as well as decrease natural vibration frequencies.

Taleghani, Barmac K.↗
NASA NTRS1993

Inclusion of transverse shear deformation in the exact buckling and vibration analysis of composite plate assemblies

The problem considered is the development of the necessary plate stiffnesses for use in the general purpose program VICONOPT for buckling and vibration of composite plate assemblies. The required stiffnesses include the effects of transverse shear deformation and are for sinusoidal response along the plate length as required in VICONOPT. The method is based on the exact solution of the plate differential equations for a composite laminate having fully populated A, B, and D stiffness matrices which leads to an ordinary differential equation of tenth order.

Anderson, Melvin S.↗
NASA NTRS1993

Vibration analysis of heated anisotropic plates with free edge conditions

Tabular and plotted results are presented (as a function of lamination angle and temperature) for the first two vibration frequencies and mode shapes of a heated, single-layer Boron/epoxy laminate. A Ritz formulation is used to determine the thermally induced in-plane forces and the out-of-plane vibration frequencies. This approach is formulated in terms of the out-of-plane displacement and the in-plane stress function; both the displacement and the stress function are expressed as simple algebraic polynomials modified to satisfy the essential boundary conditions. Heating is applied as a steady-state temperature distribution; material properties are considered to be temperature-dependent. To establish the correctness and effectiveness of the method, the in-plane forces are compared with Fourier series analytical results.

Locke, James E.↗
NASA NTRS1982

Vibration analysis of three guyed tower designs for intermediate size wind turbines

Three guyed tower designs were analyzed for intermediate size wind turbines. The four lowest natural frequencies of vibration of the three towers concepts were estimated. A parametric study was performed on each tower to determine the effect of varying such tower properties as the inertia and stiffness of the tower and guys, the inertia values of the nacelle and rotor, and the rotational speed of the rotor. Only the two lowest frequencies were in a range where they could be excited by the rotor blade passing frequencies. There two frequencies could be tuned by varying the guy stiffness, the guy attachment point on the tower, the tower and mass stiffness, and the nacelle/rotor/power train masses.

Christie, R. J.↗
NASA NTRS1988

Development of a block Lanczos algorithm for free vibration analysis of spinning structures

This paper is concerned with the development of an efficient eigenproblem solution algorithm and an associated computer program for the economical solution of the free vibration problem of complex practical spinning structural systems. Thus, a detailed description of a newly developed block Lanczos procedure is presented in this paper that employs only real numbers in all relevant computations and also fully exploits sparsity of associated matrices. The procedure is capable of computing multiple roots and proves to be most efficient compared to other existing similar techniques.

Gupta, K. K.↗
NASA NTRS1981

Development of a unified numerical procedure for free vibration analysis of structures

This paper presents the details of a unified numerical algorithm and the associated computer program developed for the efficient determination of natural frequencies and modes of free vibration of structures. Both spinning and nonspinning structures with or without viscous and/or structural damping may be solved by the current procedure; in addition, the program is capable of solving static problems with multiple load cases as well as the quadratic matrix eigenproblem associated with a finite dynamic element structural discretization.

Gupta, K. K.↗
NASA NTRS1990

Probabilistic vibration analysis of nearly periodic structures

A disordered structure with weakly coupled subsystems has localized modes with the vibratory energy concentrated in one part of the mode shape. The localization of modes may significantly affect the forced vibration response, increasing the maximum vibration amplitude dramatically in some cases. It is the scope of this paper to study the forced vibration of nearly periodic systems consisting of almost identical substructures and to analyze their free and forced dynamic responses probabilistically. It is shown that the sensitivity of the forced response to the degree of localization depends on a combination of the symmetry of the mode, which is excited, and the phase difference between the forces acting on each substructure. These results might explain the range of contrasting conclusions of earlier publications on the effects of forced response on mistuned structures. A probabilistic analysis of the free and forced responses of a nearly periodic structure is shown to be useful in the design of structures that are sensitive to the degree of localization. The results of the probabilistic analysis are verified using Monte Carlo simulation.

Hamade, Karen S.↗
NASA NTRS1994

Buckling and vibration analysis of laminated panels using VICONOPT

The analysis aspects of the 23,000-line FORTRAN program VIPASA with constraints and optimization (VICONOPT) are described. Overall stiffness matrices assembled from the earlier exact vibration and instability of plate assemblies including shear and anisotropy (VIPASA) flat plate stiffnesses are optionally coupled by Langrangian multipliers to find critical buckling loads, or natural frequencies of undamped vibration, of prismatic assemblies of anisotropic flat plates with arbitrarily located point supports or simple transverse supporting frames. The longitudunal continuity of typical wing and fuselage panels is closely approximated because the solutions are for the infinitely long structure obtained by repeating a bay and its supports longitudinally. Any longitudinally invariant in-plane plate stresses are permitted, and very rapid solutions are guaranteed by numerous refinements, including multilevel substructuring and a method for repetitive cross sections that is exact for regular polygons used to represent cylinders. Modal displacements and stresses in or between plies of laminated plates are calculated and plotted, with values being recovered at all nodes of substructures. Comparison with usual approximate finite-element methods confirms that, for comparably converged solutions, VICONOPT is typically between 100 and 10(exp 4) times faster.

Kennedy, David↗
DOE OSTI2026

Concordant Mode Approach (CMA): Vibrational Analysis of New and Upgraded Intermolecular Benchmarks for Noncovalent Bonding

The Concordant Mode Approach (CMA) is a novel method that offers tremendous potential for increasing the system size and the level of theory attainable in quantum chemical computations of molecular vibrational frequencies. To investigate the extension of CMA to intermolecular vibrations, computations with coupled cluster singles and doubles with perturbative triples theory [CCSD(T)] using two augmented correlation-consistent polarized-valence triple-ζ basis sets (aug-cc-pVTZ or h-aug-ccpVTZ) were performed on 17 prototypical loosely bound complexes of hydrogen-bonded, dispersion, and mixed character. These Level A results provide new and upgraded benchmarks for noncovalent bonding and a severe test for CMA vibrational analyses. The Level A target frequencies were recovered remarkably well using second-order Møller−Plesset perturbation theory (MP2) with h-aug-cc-pVTZ for generating the underlying (Level B) normal modes of the CMA scheme. Employing this Level B within the lowest-rung CMA-0A method reproduces the 435 benchmark frequencies with a mean absolute error (MAE) of 0.23 cm −1 and a corresponding standard deviation (σ) of 0.84 cm −1 ; strikingly, the corresponding subset of 106 interfragment frequencies exhibits MAE = 0.34 cm −1 and σ = 0.90 cm −1 . Subsequent application of the higher-rung CMA-2A scheme eliminates all outliers and reduces the overall MAE to a minuscule 0.08 cm −1 with the inclusion of only 3.0% of the off-diagonal couplings not accounted for by CMA-0A. Accordingly, the highly efficient CMA methodology proves to be robust even for vibrations on flat potential energy surfaces.

Aromatic compounds↗
NASA NTRS1994

Analytical and Experimental Vibration Analysis of a Faulty Gear System

A comprehensive analytical procedure was developed for predicting faults in gear transmission systems under normal operating conditions. A gear tooth fault model is developed to simulate the effects of pitting and wear on the vibration signal under normal operating conditions. The model uses changes in the gear mesh stiffness to simulate the effects of gear tooth faults. The overall dynamics of the gear transmission system is evaluated by coupling the dynamics of each individual gear-rotor system through gear mesh forces generated between each gear-rotor system and the bearing forces generated between the rotor and the gearbox structure. The predicted results were compared with experimental results obtained from a spiral bevel gear fatigue test rig at NASA Lewis Research Center. The Wigner-Ville distribution (WVD) was used to give a comprehensive comparison of the predicted and experimental results. The WVD method applied to the experimental results were also compared to other fault detection techniques to verify the WVD's ability to detect the pitting damage, and to determine its relative performance. Overall results show good correlation between the experimental vibration data of the damaged test gear and the predicted vibration from the model with simulated gear tooth pitting damage. Results also verified that the WVD method can successfully detect and locate gear tooth wear and pitting damage.

Choy, F. K.↗
NASA NTRS1977

Vibration analysis of rotor blades with an attached concentrated mass

The effect of an attached concentrated mass on the dynamics of helicopter rotor blades is determined. The point transmission matrix method was used to define, through three completely automated computer programs, the natural vibrational characteristics (natural frequencies and mode shapes) of rotor blades. The problems of coupled flapwise bending, chordwise bending, and torsional vibration of a twisted nonuniform blade and its special subcase pure torsional vibration are discussed. The orthogonality relations that exist between the natural modes of rotor blades with an attached concentrated mass are derived. The effect of pitch, rotation, and point mass parameters on the collective, cyclic, scissor, and pure torsional modes of a seesaw rotor blade is determined.

Murthy, V. R.↗
NASA NTRS1984

Lewis Research Center spin rig and its use in vibration analysis of rotating systems

The Lewis Research Center spin rig was constructed to provide experimental evaluation of analysis methods developed under the NASA Engine Structural Dynamics Program. Rotors up to 51 cm (20 in.) in diameter can be spun to 16,000 rpm in vacuum by an air motor. Vibration forcing functions are provided by shakers that apply oscillatory axial forces or transverse moments to the shaft, by a natural whirling of the shaft, and by an air jet. Blade vibration is detected by strain gages and optical blade-tip motion sensors. A variety of analogy and digital processing equipment is used to display and analyze the signals. Results obtained from two rotors are discussed. A 56-blade compressor disk was used to check proper operation of the entire spin rig system. A special two-blade rotor was designed and used to hold flat and twisted plates at various setting and sweep angles. Accurate Southwell coefficients have been obtained for several modes of a flat plate oriented parallel to the plane of rotation.

Brown, G. V.↗
NASA NTRS1985

Vibration analysis of rotating turbomachinery blades by an improved finite difference method

The problem of calculating the natural frequencies and mode shapes of rotating blades is solved by an improved finite difference procedure based on second-order central differences. Lead-lag, flapping and coupled bending-torsional vibration cases of untwisted blades are considered. Results obtained by using the present improved theory have been observed to be close lower bound solutions. The convergence has been found to be rapid in comparison with the classical first-order finite difference method. While the computational space and time required by the present approach is observed to be almost the same as that required by the first-order theory for a given mesh size, accuracies of practical interest can be obtained by using the improved finite difference procedure with a relatively smaller matrix size, in contrast to the classical finite difference procedure which requires either a larger matrix or an extrapolation procedure for improvement in accuracy.

Subrahmanyam, K. B.↗
NASA NTRS1995

Vibration Analysis of a Split Path Gearbox

Split path gearboxes can be attractive alternatives to the common planetary designs for rotorcraft, but because they have seen little use, they are relatively high risk designs. To help reduce the risk of fielding a rotorcraft with a split path gearbox, the vibration and dynamic characteristics of such a gearbox were studied. A mathematical model was developed by using the Lagrangian method, and it was applied to study the effect of three design variables on the natural frequencies and vibration energy of the gearbox. The first design variable, shaft angle, had little influence on the natural frequencies. The second variable, mesh phasing, had a strong effect on the levels of vibration energy, with phase angles of 0 deg and 180 deg producing low vibration levels. The third design variable, the stiffness of the shafts connecting the spur gears to the helical pinions, strongly influenced the natural frequencies of some of the vibration modes, including two of the dominant modes. We found that, to achieve the lowest level of vibration energy, the natural frequencies of these two dominant modes should be less than those of the main excitation sources.

Krantz, Timothy L.↗
NASA NTRS1997

Vibrational Analysis of Engine Components Using Neural-Net Processing and Electronic Holography

The use of computational-model trained artificial neural networks to acquire damage specific information from electronic holograms is discussed. A neural network is trained to transform two time-average holograms into a pattern related to the bending-induced-strain distribution of the vibrating component. The bending distribution is very sensitive to component damage unlike the characteristic fringe pattern or the displacement amplitude distribution. The neural network processor is fast for real-time visualization of damage. The two-hologram limit makes the processor more robust to speckle pattern decorrelation. Undamaged and cracked cantilever plates serve as effective objects for testing the combination of electronic holography and neural-net processing. The requirements are discussed for using finite-element-model trained neural networks for field inspections of engine components. The paper specifically discusses neural-network fringe pattern analysis in the presence of the laser speckle effect and the performances of two limiting cases of the neural-net architecture.

Decker, Arthur J.↗
NASA NTRS1998

Vibrational Analysis of Engine Components Using Neural-Net Processing and Electronic Holography

The use of computational-model trained artificial neural networks to acquire damage specific information from electronic holograms is discussed. A neural network is trained to transform two time-average holograms into a pattern related to the bending-induced-strain distribution of the vibrating component. The bending distribution is very sensitive to component damage unlike the characteristic fringe pattern or the displacement amplitude distribution. The neural network processor is fast for real-time visualization of damage. The two-hologram limit makes the processor more robust to speckle pattern decorrelation. Undamaged and cracked cantilever plates serve as effective objects for testing the combination of electronic holography and neural-net processing. The requirements are discussed for using finite-element-model trained neural networks for field inspections of engine components. The paper specifically discusses neural-network fringe pattern analysis in the presence of the laser speckle effect and the performances of two limiting cases of the neural-net architecture.

Decker, Arthur J.↗
NASA NTRS2002

Advanced Vibration Analysis Tools and New Strategies for Robust Design of Turbine Engine Rotors

The adverse effects of small, random structural irregularities among the blades, called mistuning, can result in blade forced-response amplitudes and stresses that are much larger than those predicted for a perfectly tuned rotor. Manufacturing tolerances, deviations in material properties, or nonuniform operational wear causes mistuning; therefore, mistuning is unavoidable. Furthermore, even a small mistuning can have a dramatic effect on the vibratory behavior of a rotor because it can lead to spatial localization of the vibration energy (see the following photographs). As a result, certain blades may experience forced response amplitudes and stresses that are substantially larger than those predicted by an analysis of the nominal (tuned) design. Unfortunately, these random uncertainties in blade properties, and the immense computational effort involved in obtaining statistically reliable design data, combine to make this aspect of rotor design cumbersome.

Min, James B.↗
NASA NTRS2002

Advanced Vibration Analysis Tools and New Strategies for Robust Design of Turbine Engine Rotors

The adverse effects of small, random structural irregularities among the blades, called mistuning, can result in blade forced-response amplitudes and stresses that are much larger than those predicted for a perfectly tuned rotor. Manufacturing tolerances, deviations in material properties, or nonuniform operational wear causes mistuning; therefore, mistuning is unavoidable. Furthermore, even a small mistuning can have a dramatic effect on the vibratory behavior of a rotor because it can lead to spatial localization of the vibration energy (see the following photographs). As a result, certain blades may experience forced response amplitudes and stresses that are substantially larger than those predicted by an analysis of the nominal (tuned) design. Unfortunately, these random uncertainties in blade properties, and the immense computational effort involved in obtaining statistically reliable design data, combine to make this aspect of rotor design cumbersome.

Min, James B.↗