Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermomechanical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Thermomechanical Degradation of Sintered Copper Under High-Temperature Thermal Shock

The need for reliable bonded interface materials is critical to realize the performance benefits of wide-bandgap devices in power electronics modules, especially in operating temperatures greater than 150 degrees C. In this paper, we investigate the thermomechanical performance of sintered copper (Cu) as a large-area attachment, bonded between Cu baseplates and active-metal-bonded substrates, under accelerated thermal shock (-40 degrees C to 200 degrees C) conditions. In the fabrication phase of the samples, we used different stencil patterns and found that the grid and stripe patterns resulted in a better outgassing of the residual organics during the sintering process, thereby ensuring a substantially improved bond quality compared to a full-area print. The paste consisted of Cu microflakes, and we performed sintering using a Budatec SP300 sintering press at 275 degrees C with 15 MPa of bonding pressure for 5 minutes in a nitrogen atmosphere. Under accelerated experiments, we monitored the degradation of the sintered Cu bond in the samples through C-mode scanning acoustic microscope (C-SAM) images. To quantify the defect percentage in C-SAM images, we investigated image denoising techniques to exclude the pattern prints. Finally, we cross-sectioned a sample and obtained scanning electron microscope images, which revealed adhesive fracture as the dominant failure mechanism.

ADVANCED PROPULSION SYSTEMS,INORGANIC, ORGANIC, PH↗
DOE OSTI2024

Multifunctional Nanofiber Reinforcement for Improved Thermomechanical and Chemical Stability of Perovskite Solar Cells

This project focused on the development of metal halide perovskite-polymeric nanofiber nanocomposites for robust and efficient solar cells. Metal halide perovskite solar cells are a potentially disruptive technology with high efficiencies and low-cost solution processability amenable with roll-to-roll fabrication of flexible devices. However, perovskites exhibit extreme brittleness, high internal film stresses, and chemical instabilities that significantly limit service lifetimes under normal operating conditions. To date, most work addressing these shortcomings has been focused on encapsulating devices between thick layers of rigid materials such as glass, which increases the total weight and cost of devices. Furthermore, these rigid and heavy encapsulants do not translate well to emerging solar markets vital for national security, including integrated mobile power, emergency deployments for disaster relief and military engagement, and lightweight power for space. It is therefore critical to improve the thermomechanical and chemical stability of perovskite devices in a way that is compatible with flexible and lightweight substrates. In this project, we integrated nylon-6,6 nanofibers into MAPbI3 to mechanically reinforce the perovskite, demonstrating films that exhibited fracture energies 5-fold greater than pristine MAPbI3 while also maintaining similar power conversion efficiencies due to beneficial light scattering effects from the polymeric nanofibers. These results required successful development of approaches to control the deposition thickness of nanofiber mats down to 100s of nanometers, and to ensure the polymer nanofibers did not inhibit charge transport to the at the perovskite-transport layer interface.

14 SOLAR ENERGY↗
DOE OSTI2024

Thermomechanical Processing for Improved Mechanical Properties of HT9 Steels

Thermomechanical processing (TMP) of ferritic–martensitic (FM) steels, such as HT9 (Fe–12Cr–1MoWV) steels, involves normalizing, quenching, and tempering to create a microstructure of fine ferritic/martensitic laths with carbide precipitates. HT9 steels are used in fast reactor core components due to their high-temperature strength and resistance to irradiation damage. However, traditional TMP methods for these steels often result in performance limitations under irradiation, including embrittlement at low temperatures (<~430 °C), insufficient strength and toughness at higher temperatures (>500 °C), and void swelling after high-dose irradiation (>200 dpa). This research aimed to enhance both fracture toughness and strength at high temperatures by creating a quenched and tempered martensitic structure with ultrafine laths and precipitates through rapid quenching and unconventional tempering. Mechanical testing revealed significant variations in strength and fracture toughness depending on the processing route, particularly the tempering conditions. Tailored TMP approaches, combining rapid quenching with limited tempering, elevated strength to levels comparable to nano-oxide strengthened ferritic alloys while preserving fracture toughness. For optimal properties in high-Cr steels for future reactor applications, this study recommends a modified tempering treatment, i.e., post-quench annealing at 500 °C or 600 °C for 1 h, possibly followed by a brief tempering at a slightly higher temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tuning the 3D Printability and Thermomechanical Properties of Radiation Shields

Additive manufacturing, with its rapid advances in materials science, allows for researchers and companies to have the ability to create novel formulations and final parts that would have been difficult or near impossible to fabricate with traditional manufacturing methods. One such 3D printing technology, direct ink writing, is especially advantageous in fields requiring customizable parts with high amounts of functional fillers. Nuclear technology is a prime example of a field that necessitates new material design with regard to unique parts that also provide radiation shielding. Indeed, much effort has been focused on developing new rigid radiation shielding components, but DIW remains a less explored technology with a lot of potential for nuclear applications. In this study, DIW formulations that can behave as radiation shields were developed and were printed with varying amounts of porosity to tune the thermomechanical performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mechanical and thermomechanical properties of an LLM-105 based PBX high explosive with and without accelerated aging

In this paper we present measurements and analysis on the mechanical and thermomechanical properties of the LLM-105 based plastic bonded high explosive RX-55-DQ. Specifically we present uni-axial compression, and thermal measurements (CTE and ratchet growth), and for some of the measurements we provide a comparison to measurements on TATB-based PBX 9502. We also present the same mechanical property measurements performed on RX-55-DQ samples that underwent accelerated aging.

thermomechnical properties↗
DOE OSTI2023

Thermomechanical Cleave of Polycrystalline CdTe Solar Cells and its Applications: A Review

One of the primary research challenges for cadmium telluride (CdTe) solar cells is addressing its open‐circuit voltage ( V OC ) deficit. While theoretical studies and single crystal work show V OC > 1 V is possible, devices remain stubbornly low at ≈800–900 mV. As absorber opto‐electronic properties (e.g., hole density, carrier lifetime) are improved, device modeling suggests that interfaces become limiting. Because CdTe‐based devices are typically grown in the superstrate configuration, the back interface is relatively accessible for manipulation and study, while the front interface (i.e., the heterojunction region) is buried under microns of material and inaccessible. NREL has developed a novel technique to thermomechanically cleave polycrystalline CdTe device stacks directly at the front interface, enabling characterization and controlled manipulation of this important region. Herein, recent work, primarily from NREL, will be reviewed, including considerations for achieving successful delamination; key scientific discoveries about the front interface that have been enabled by this technique; and practical applications, such as flexible, low‐cost solar with high power‐to‐weight ratio.

14 SOLAR ENERGY↗
DOE OSTI2020

Extensive nanoprecipitate morphology transformation in a nanostructured ferritic alloy due to extreme thermomechanical processing

Nano-oxide precipitates in a modern nanostructured ferritic alloy were investigated after extreme thermomechanical processing into a thin-walled tube geometry. It was found that the morphology of the precipitates changed from spherical to rod-shaped, with some increasing to aspect ratios of up to 9, despite the precipitate volume fraction (0.3%) and number density (> 10 23 m -3 ) of precipitates remaining unchanged. High-resolution electron microscopy showed that the precipitates likely remained coherent with the Fe-matrix, while atom probe tomography confirmed that the precipitate compositions remained unaffected by the transformation. The morphological change was attributed to the shearable nature of the (Y,Ti,O)-rich precipitates, indicating they should be considered as “soft” obstacles to dislocation motion. The elongation was most pronounced in larger (>5 nm) precipitates, which may be caused by preferential dissolution of the smallest (1–3 nm) precipitates followed by the competition between re-precipitation and solute diffusion to larger precipitates during recovery heat treatments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On the efficacy of post-build thermomechanical treatments to improve properties of Zirconium fabricated using ultrasonic additive manufacturing

Here, hot-isostatic pressing has been applied to Zirconium plate fabricated using the ultrasonic additive manufacturing (UAM) technique to enhance interfacial bond quality. Specimens heated to 800 C for 1 h at 100 MPa pressure showed grain growth across many prior foil-to-foil interfaces, thereby increasing foil adhesion. In addition to the material softening induced by a loss of Hall-Petch strengthening, premature failure of specimens loaded parallel to the build direction was observed. Premature specimen failure was attributed to the local delamination at prior foil-to-foil boundaries where grain growth was pinned by Ti impurities introduced during the UAM process via the interaction between a Ti-alloy buffer foil and the welded Zr-foils underneath. In addition, the presence of Ti along select foil interfaces resulted in the nucleation and growth of secondary (Zr,Ti)(Fe,Cr) laves phases during higher-temperature thermomechanical processing. Using a combination of micro-scale X-ray computed tomography, fractography, and in-situ digital image correlation, the effect of defects along prior foil-to-foil boundaries was revealed as delamination-assisted plasticity accelerated specimen failure in preferred tensile orientations. These findings underscore the importance of impurity control when optimizing weld quality of higher-strength material systems using ultrasonic welding.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Engineering mechanical and thermomechanical performance in additive manufacturing–Compression molded composites through multiplexed extrusion

Traditional extrusion-based additive manufacturing is limited to single material systems, restricting the multifunctional properties of composites. For this work to overcome this limitation, multiplexed additive manufacturing–compression molding (AM-CM) was employed to fabricate multi-material thermoplastic composites with spatially tailored architectures. Neat acrylonitrile butadiene styrene (ABS) and 20 wt% carbon-fiber reinforced ABS (CF-ABS) were co-extruded through a core–sheath nozzle to produce hybrid composites with neat ABS as sheath (30-50 wt%) and CF-ABS as core (50 – 70 wt%). The results show that the hybrid composites have balance of mechanical and thermomechanical performance. The tensile strength and modulus of hybrid composites exhibited a 61–95% and 173–473% increase compared to neat ABS with increases in CF-ABS content whereas the impact resistance improved by 41% compared to CF-ABS at 50 wt% ABS. Additionally, hybrid composites showed significant reduction (54 - 70%) in creep strain at 100 °C compared to neat ABS. These findings demonstrate that multiplexed AM-CM enables tunable structure–property relationships, reducing CF-ABS usage up to 50 wt% while maintaining balanced stiffness, toughness, and creep resistance.

Additive manufacturing↗
DOE OSTI2025

Neutron irradiation & thermomechanical experiment (NITE) - design

For the reliable long-term operation of fusion power plants, it is crucial to understand and predict the lifetime of materials in use. These materials include all structural and functional materials utilized at the first wall, blanket, magnets, and shielding. The key challenge is, that the harsh environment including high heat fluxes, high thermal stress and stress cycling, neutron irradiation, and sputtering on such materials should not be viewed separately. Currently, the synergistic loads cannot be evaluated experimentally because of the lack of adequate facilities. The purpose of that work is to design a synergetic Neutron Irradiation and Thermomechanical Experiment (NITE) for fusion materials. This design will leverage the existing Advanced-Test-Reactor (ATR), a fission reactor at the Idaho National Laboratory. We also acknowledge that with existing fission reactors the exact fusion condition cannot be created, and the limitations are critically discussed. The combination of neutron irradiation with a high heat flux is the focus. This is realized with an irradiation capsule design that includes a TRISO fueled region inside the capsule to enable a steady-state heat flux on one side of the specimen. In conclusion, the experimental design modeling showed that steady-state heat fluxes of 2.4 MW/m 2 with a thermal gradient of above 250°C can be achieved in a 5 mm thick specimen.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Thermomechanical properties and microstructures of yttrium hydride

Yttrium hydride is an optimal choice for a high-temperature moderator material in advanced thermal neutron spectrum reactors that require small core volumes. However, a complete database of the thermomechanical properties of yttrium hydride is not available yet, although it is much needed to understand and predict the moderator performance during service in reactors. In this paper, we report the properties of unirradiated bulk yttrium hydride as a function of hydrogen concentration—including density, crystal structure, specific heat capacity, thermal diffusivity, thermal conductivity, hardness, elastic/shear moduli, Poisson’s ratio, fracture strength, microstructure, and thermal stability—providing a baseline measurement for the subsequent neutron irradiation response study of yttrium hydride. Furthermore, the recommended empirical treatment of the data is suggested. In addition, other properties (i.e., hydrogen retention, thermal hydrogen migration, and irradiation response) that needs to be investigated are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ionic complexation of endblock-sulfonated thermoplastic elastomers and their physical gels for improved thermomechanical performance

Thermoplastic elastomers (TPEs) composed of nonpolar triblock copolymers constitute a broadly important class of (re)processable network-forming macromolecules employed in ubiquitous commercial applications. Physical gelation of these materials in the presence of a low-volatility oil that is midblock-selective yields tunably soft TPE gels (TPEGs) that are suitable for emergent technologies ranging from electroactive, phase-change and shape-memory responsive media to patternable soft substrates for flexible electronics and microfluidics. Many of the high-volume TPEs used for these purposes possess styrenic endblocks that are inherently limited by a relatively low glass transition temperature. To mitigate this shortcoming, we sulfonate and subsequently complex (and physically crosslink) the endblocks with trivalent Al3+ ions. Doing so reduces the effective hydrophilicity of the sulfonated endblocks, as evidenced by water uptake measurements, while concurrently enhancing the thermomechanical stability of the corresponding TPEGs. Chemical modification results, as well as morphological and property development, are investigated as functions of the degree of sulfonation, complexation and TPEG composition. (C) 2020 Published by Elsevier Inc.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Temperature-dependent mechanism on hardening mitigation in thermomechanically processed 800H alloys under neutron irradiation

Irradiation induced hardening is commonly observed in structural materials, and is often associated with the degraded ductility. This study explores the role of thermomechanical processing (TMP) in mitigating irradiation-induced hardening in Incoloy 800H. The radiation response of solution-annealed and TMP-treated samples was systematically investigated to elucidate the underlying mechanisms of hardening reduction. Neutron irradiation was performed on solution-annealed and TMP-treated samples at 359, 431, and 580 °C, revealing consistently lower hardening in TMP samples. Microstructural characterization compared dislocation loops, cavities, clusters, and precipitates to assess their contributions to hardening. The strengthening contributions from individual microstructural features were estimated, and the microstructure-derived yield strength is consistent with the hardness-converted yield strength. The microstructure–properties correlation revealed the temperature-dependent primary hardening mechanism: dislocation loops dominated at lower temperature, whereas Ni3(Al,Ti) γ′ precipitates were predominant at higher temperature. TMP reduced radiation-induced hardening through two mechanisms: (1) increased sink strength from dislocations and Ti(C,N) precipitates limited dislocation loop formation at lower temperatures, and (2) reduced Ti solute within the matrix in TMP samples suppressed γ′ precipitate formation at higher temperatures. These findings identify the mechanisms governing radiation-induced hardening across different temperatures, which lays the foundation for TMP optimization for the development of advanced radiation-tolerant materials.

Zhong, Weicheng [ORNL] (ORCID:0000000231589271)↗
DOE OSTI2024

Friction stir processing: A thermomechanical processing tool for high pressure die cast Al-alloys for vehicle light-weighting

This study uses friction stir processing (FSP) for thermomechanical processing of high-pressure die-casting (HPDC) to modify microstructure and improve mechanical properties. FSP is carried out on two different HPDC aluminum alloys: (a) general-purpose, high-iron, HPDC A380 alloy and (b) premium quality, low-iron HPDC Aural-5 alloy in thin wall, flat plate geometry. Subsequent mechanical testing shows ~30 % and ~65 % enhancement in yield strength and tensile ductility. In addition, FSP leads to ~10 times improvement in fatigue life for A380 alloy and ~70 % improvement in fracture toughness for Aural-5 alloy. These findings emphasize the capability of FSP to modify the microstructure of HPDC Al-alloys-based structural components so that they can demonstrate a good combination of strength, ductility, fracture toughness, and high fatigue properties for long-term durability and reliability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Varied enhancements in mechanical properties and sodium compatibility of Grade 92 by thermomechanical treatments

As a candidate material for advanced nuclear reactors, a ferritic-martensitic (FM) steel Grade 92 in the standard normalized and tempered (NT) condition was subjected to two types of thermomechanical treatments (TMTs) with one having a lower level of deformation (T5A) and the other having a higher level of deformation (T5B). The testing results of the three conditions indicated that the TMTs significantly improved yield strength, creep resistance, fracture toughness, and sodium corrosion resistance compared with the NT condition. T5A excelled at creep resistance while T5B at sodium corrosion resistance. Microstructural characterization of the three conditions supports the varied enhancements in the properties. This study suggests that an appropriate TMT can be developed and applied to FM steels to better meet specific application requirements.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of hatch spacing and laser power on microstructure, texture, and thermomechanical properties of laser powder bed fusion (L-PBF) additively manufactured NiTi

This study systematically evaluates the effects of laser powder bed fusion additive manufacturing (L-PBF-AM) parameters (hatch spacing and laser power) on the thermomechanical behavior and microstructure of Ni 50.8 Ti 49.2 shape memory alloy. The samples were fabricated with hatch spacings from 40 to 240 µm and laser powers of 50 and 100 W at a constant scanning speed of 125 mm/s, resulting in parts with volumetric energy density levels from 55 to 666 J/mm 3 and two sets of linear energy densities of 0.4 and 0.8 J/mm. The results showed a reduced melt pool size and discontinuity of scan tracks with decreased laser power. Additionally, the porosity level was increased with larger hatch spacing and lower laser power. More notably, the transformation temperatures increased, and the critical stress, recoverable strain, and functional stability of samples improved with lower hatch spacing, where the recovery ratio of up to 90% was observed, regardless of the employed laser power. This study also discussed the relationship between the fabrication process and texture formation in the L-PBF-AM process. In conclusion, the advantage of L-PBF-AM was revealed in tailoring the microstructure from highly textured samples in [1 1 1] or [0 0 1] direction when hatch spacing lower than laser beam focused was employed, to the appearance of equiaxed solidification front with island grains and random orientations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synthesis and thermomechanical characteristics of zwitterionic poly(arylene ether sulfone) copolymers

Charge-containing polymeric materials have been widely studied for a range of applications. The fundamental relationships between the charge species, charge density, and the microscale morphology of charge-containing polymers are critical for defining the application in which they may be used. In this work, a series of thermoplastic poly(arylene ether sulfone) (PAES) copolymers with controllable sulfobetaine charge contents (0~100 mol%) and high molecular weights (Mw ~ 65 kDa) were prepared. All the zwitterionic PAESs synthesized showed thermal stability up to 250 °C. DSC and tensile tests showed a decreased T g and mechanical strength with the incorporation of increasing charge density, which suggests a plasticization effect by the charged group. Electron microscopy and X-ray scattering data confirmed the absence of microphase separation in the ion-containing random copolymer system, which corroborated with the observation of a single T g for all zwitterionic copolymers studied. Furthermore, the relative hydrophilicity of the samples was evaluated by water uptake measurements, which revealed that the water uptake of the zwitterionic PAESs can reach up to 64% for the 72 mol% zwitterion copolymer while the free-standing film in the wet state still maintains a Young's modulus of 185 MPa. Here, the thermoplastic charge-containing copolymers in this work demonstrated potential for applications such as coatings or water purification membranes, in which balancing hydrophilicity, processibility, and thermomechanical performance are important.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Unexpected Thermomechanical Behavior of Off-Stoichiometry Epoxy/Amine Materials

Recent studies on off-stoichiometric thermosets reveal unique viscoelastic behavior derived from increased free volume and physical interactions between chain ends. To understand structural characteristics arising from cure and its effect on properties, we developed a Monte Carlo model based on step-growth polymerization. Our model accurately predicted structure–property trends for a two-component system of EPON 828 (EPON) and ethylenediamine. A second epoxy monomer, D.E.R. 732 (DER), was investigated to modulate T g . Binary mixtures of EPON and DER in off-stoichiometric, amine-rich formulations resulted in nonlinear evolution of thermomechanical properties with respect to initial formulation stoichiometry. Modifying our model with kinetic parameters allowing for differential epoxide/amine reaction kinetics only partially accounted for trends in T g , suggesting that spatiotemporal contributions-not captured by our model-were significant determinants of material properties compared to polymer architecture for three-component systems. Here these findings underpin the importance of spatial awareness in modeling to inform the development of dynamic thermosets.

36 MATERIALS SCIENCE↗