Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal losses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Heat Control via Torque Control in Friction Stir Welding

In a proposed advance in friction stir welding, the torque exerted on the workpiece by the friction stir pin would be measured and controlled in an effort to measure and control the total heat input to the workpiece. The total heat input to the workpiece is an important parameter of any welding process (fusion or friction stir welding). In fusion welding, measurement and control of heat input is a difficult problem. However, in friction stir welding, the basic principle of operation affords the potential of a straightforward solution: Neglecting thermal losses through the pin and the spindle that supports it, the rate of heat input to the workpiece is the product of the torque and the speed of rotation of the friction stir weld pin and, hence, of the spindle. Therefore, if one acquires and suitably processes data on torque and rotation and controls the torque, the rotation, or both, one should be able to control the heat input into the workpiece. In conventional practice in friction stir welding, one uses feedback control of the spindle motor to maintain a constant speed of rotation. According to the proposal, one would not maintain a constant speed of rotation: Instead, one would use feedback control to maintain a constant torque and would measure the speed of rotation while allowing it to vary. The torque exerted on the workpiece would be estimated as the product of (1) the torque-multiplication ratio of the spindle belt and/or gear drive, (2) the force measured by a load cell mechanically coupled to the spindle motor, and (3) the moment arm of the load cell. Hence, the output of the load cell would be used as a feedback signal for controlling the torque (see figure).

Venable, Richard↗
NASA NTRS2009

Test Rack Development for Extended Operation of Advanced Stirling Convertors at NASA Glenn Research Center

The U.S. Department of Energy (DOE), Lockheed Martin Space Company (LMSC), Sun power Inc., and NASA Glenn Research Center (GRC) have been developing an Advanced Stirling Radioisotope Generator (ASRG) for use as a power system on space science missions. This generator will make use of free-piston Stirling convertors to achieve higher conversion efficiency than currently available alternatives. NASA GRC's support of ASRG development includes extended operation testing of Advanced Stirling Convertors (ASCs) developed by Sunpower Inc. In the past year, NASA GRC has been building a test facility to support extended operation of a pair of engineering level ASCs. Operation of the convertors in the test facility provides convertor performance data over an extended period of time. Mechanical support hardware, data acquisition software, and an instrumentation rack were developed to prepare the pair of convertors for continuous extended operation. Short-term tests were performed to gather baseline performance data before extended operation was initiated. These tests included workmanship vibration, insulation thermal loss characterization, low-temperature checkout, and fUll-power operation. Hardware and software features are implemented to ensure reliability of support systems. This paper discusses the mechanical support hardware, instrumentation rack, data acquisition software, short-term tests, and safety features designed to support continuous unattended operation of a pair of ASCs.

Dugala, Gina M.↗
NASA NTRS2012

Advanced Stirling Radioisotope Generator Thermal Power Model in Thermal Desktop SINDA/FLUINT Analyzer

This paper presents a three-dimensional Advanced Stirling Radioisotope Generator (ASRG) thermal power model that was built using the Thermal Desktop SINDA/FLUINT thermal analyzer. The model was correlated with ASRG engineering unit (EU) test data and ASRG flight unit predictions from Lockheed Martin's Ideas TMG thermal model. ASRG performance under (1) ASC hot-end temperatures, (2) ambient temperatures, and (3) years of mission for the general purpose heat source fuel decay was predicted using this model for the flight unit. The results were compared with those reported by Lockheed Martin and showed good agreement. In addition, the model was used to study the performance of the ASRG flight unit for operations on the ground and on the surface of Titan, and the concept of using gold film to reduce thermal loss through insulation was investigated.

Wang, Xiao-Yen↗
NASA NTRS2014

MHD Modelling of Coronal Loops: Injection of High-Speed Chromospheric Flows

Context. Observations reveal a correspondence between chromospheric type II spicules and bright upward-moving fronts in the corona observed in the extreme-ultraviolet (EUV) band. However, theoretical considerations suggest that these flows are probably not the main source of heating in coronal magnetic loops. Aims. We investigate the propagation of high-speed chromospheric flows into coronal magnetic flux tubes and the possible production of emission in the EUV band. Methods. We simulated the propagation of a dense 104 K chromospheric jet upward along a coronal loop by means of a 2D cylindrical MHD model that includes gravity, radiative losses, thermal conduction, and magnetic induction. The jet propagates in a complete atmosphere including the chromosphere and a tenuous cool (approximately 0.8 MK) corona, linked through a steep transition region. In our reference model, the jet initial speed is 70 km per second, its initial density is 10(exp 11) per cubic centimeter, and the ambient uniform magnetic field is 10 G. We also explored other values of jet speed and density in 1D and different magnetic field values in 2D, as well as the jet propagation in a hotter (approximately 1.5 MK) background loop. Results. While the initial speed of the jet does not allow it to reach the loop apex, a hot shock-front develops ahead of it and travels to the other extreme of the loop. The shock front compresses the coronal plasma and heats it to about 10(exp 6) K. As a result, a bright moving front becomes visible in the 171 Angstrom channel of the SDO/AIA mission. This result generally applies to all the other explored cases, except for the propagation in the hotter loop. Conclusions. For a cool, low-density initial coronal loop, the post-shock plasma ahead of upward chromospheric flows might explain at least part of the observed correspondence between type II spicules and EUV emission excess.

Sun: chromosphere↗
DOE OSTI2020

High flux thermal receiver and method of use

A thermal receiver, such as a solar flux thermal receiver, is disclosed comprising a modular arrangement of arrayed microchannels or micropins to heat a working fluid by heat transfer. Disclosed solar receivers provide a much higher solar flux and consequently a significant reduction in thermal losses, size, and cost, relative to known receivers. Unit cell receivers can be numbered up and combined in parallel to form modules, and modules combined to form full scale receivers.

14 SOLAR ENERGY↗
DOE OSTI2022

Luminescent solar concentrators and related methods of manufacturing

Luminescent solar concentrators in accordance with various embodiments of the invention can be designed to minimize photon thermalization losses and incomplete light trapping using various components and techniques. Cadmium selenide core, cadmium sulfide shell (CdSe/CdS) quantum dot (“QD”) technology can be implemented in such devices to allow for near-unity QDs and sufficiently large Stokes shifts. Many embodiments of the invention include a luminescent solar concentrator that incorporates CdSe/CdS quantum dot luminophores. In further embodiments, anisotropic luminophore emission can be implemented through metasurface/plasmonic antenna coupling. In several embodiments, red-shifted luminophores are implemented. Additionally, top and bottom spectrally-selective filters, such as but not limited to selectively-reflective metasurface mirrors and polymeric stack filters, can be implemented to enhance the photon collection efficiency. In some embodiments, luminescent solar concentrator component is optically connected in tandem with a planar Si subcell, forming a micro-optical tandem luminescent solar concentrator.

Needell, David R.↗
DOE OSTI2026

Universal Optimization and Tighter Fidelity Bounds for Approximate Quantum Error Correction

Approximate quantum error correction (AQEC) not only dictates the performance of discrete- and continuous-variable quantum error correction codes but also serves as a unifying framework across various physical disciplines. Identifying the optimal recovery channel to maximize the entanglement fidelity via standard semidefinite programming is computationally bottlenecked by the exponentially growing number of Kraus operators with system size, rendering large-scale optimization prohibitive. While analytical near-optimal maps exist, they typically work only when the Knill-Laflamme conditions are nearly satisfied. In this Letter, we establish an efficient framework by leveraging the duality between recovery and environment decoupling. This framework yields a tighter analytical lower bound on entanglement fidelity than the conventional limit set by the transpose channel. Furthermore, by exploiting the decayed weights of noise Kraus operators, we introduce a framework based on principal component analysis to reduce the dimension. In thermal loss channels where the weights decay exponentially, our approach achieves a 33-fold computational speedup while maintaining rigorous accuracy. Our approach enables high-precision optimization for AQEC codes that were previously intractable due to the curse of dimensionality.

Wu, Jing [Fermilab] (ORCID:0000000249460732)↗
NASA NTRS1966

Stabilization of Tungsten-Uranium Dioxide Composites Under Thermal Cycling Conditions

Uranium losses during thermal cycling of tungsten - uranium dioxide composites to 2500° C in flowing purified hydrogen for specimens initially containing 35 volume percent uranium dioxide were reduced by the use of thorium dioxide, calcium oxide, or yttrium oxide as additives in solid solution with the uranium dioxide. The effectiveness of the additives decreased in the order yttrium oxide, calcium oxide, and thorium dioxide. Stabilization of uranium dioxide by calcium oxide or yttrium oxide can be explained in part on the basis of the introduction of oxygen vacancies into the fluorite lattice and the associated lowered partial molar free energy of oxygen. The difference in the effectiveness of calcium oxide and yttrium oxide is discussed, and a possible explanation of the observed behavior is proposed. Of the concentrations of yttrium oxide tested (i.e., 2. 5, 5, and 10 mole percent), 10 mole percent of yttrium oxide was the most effective in pre­ venting loss of uranium from composities.

Gluyas, Richard E.↗
NASA NTRS1991

A model for the scattering of high-frequency electromagnetic fields from dielectrics exhibiting thermally-activated electrical losses

An equivalent circuit model (ECM) approach is used to predict the scattering behavior of temperature-activated, electrically lossy dielectric layers. The total electrical response of the dielectric (relaxation + conductive) is given by the ECM and used in combination with transmission line theory to compute reflectance spectra for a Dallenbach layer configuration. The effects of thermally-activated relaxation processes on the scattering properties is discussed. Also, the effect of relaxation and conduction activation energy on the electrical properties of the dielectric is described.

Hann, Raiford E.↗
DOE OSTI2020

Sodium Ion Expansion Power Block for Distributed CSP

The Sodium Ion Expansion Power Block for Distributed CSP was a three-plus-one-year effort under the Concentrating Solar Power: Advanced Projects Offering Low LCOE Opportunities (CSP: APOLLO) funding program within the U.S. Department of Energy Solar Energy Technologies Office. The primary objective of this project is to develop a dual-stage modular sodium thermal electrochemical converter (Na-TEC) heat engine power block, which can be potentially integrated with either a small-scale dish solar or large-scale heliostats and parabolic trough CSP. Na-TEC is a heat engine that generates electricity through the isothermal expansion of sodium ions. The Na-TEC is a closed system that can theoretically achieve conversion efficiencies above 45% when operating between thermal reservoirs at 1150 K and 550 K. However, thermal designs have confined previous single-stage devices to thermal efficiencies below 20%. To mitigate some of these limitations, we consider dividing the isothermal expansion into two stages; one at the evaporator temperature (1150 K) and another at an intermediate temperature (650 K –1050 K). This dual-stage Na-TEC takes advantage of regeneration and reheating, and could be amenable to better thermal management. In light of this, we first designed and developed a thermo-electrochemical model, and thermodynamically demonstrated how the dual-stage device can improve the efficiency by up to 8% points over the best performing single-stage device. We also established an application regime map for the single- and dual-stage Na-TEC in terms of the power density and the total thermal parasitic loss. Moreover, a thermal design of an axisymmetric dual-stage Na-TEC is developed to guide the scale-up and fabrication of sub-components of prototype module. A reduced-order finite-element model is used in conjunction with a Na-TEC thermodynamic model that was developed to determine the total parasitic heat loss of this dual-stage design. A number of simplifications are applied in the reduced-order model to decrease the computational time while maintaining acceptable accuracy. According to this analysis, a maximum efficiency of 29% and a maximum power output of 125 W can be achieved. Ultimately, we were able to demonstrate thermal efficiency improvements of the Na-TEC heat engine from 19% up to 40.3%, in a dual-stage (non-optimized) prototype module that we designed, fabricated, and tested with high temperature stage at 923 K. Furthermore, a cost-performance analysis for this improved dual-stage design was carried out for distributed-CSP systems. A high-level techno-economic analysis (TEA) explores four scenarios where a Na-TEC is used as the heat engine for a distributed-CSP system. Overnight capital cost and levelized cost of electricity (LCOE) are estimated for a system lifetime of 30 years, revealing that overnight capital costs in a range from $3.57 to $17.71 per We are feasible, which equate to LCOEs from 6.9 to 17.2 cents/kWh e -1 . This analysis makes a significant contribution by concurrently quantifying the efficiency and unit costs for a range of multistage configurations, and demonstrating that a Na-TEC may be a promising alternative to Stirling engines for distributed-CSP systems at residential scale of 1–5 kW e .

14 SOLAR ENERGY↗
NASA NTRS1995

The direction of heat flow in an expanding current free stellar atmosphere

The energy budgets of the corona are substantially influenced by losses attributed to thermal conduction losses down the transition region, towards the chromosphere. Although Fourier law for such a plasma regime is now universally criticized as inappropriate, the direction of this heat flow seems to be certain. The purpose of this paper is to point out, based on conservation laws, the direction in which the heat must flow in this regime, provided it is known that there is a time independent expansion devoid of parallel currents. It will be argued that the direction of the heat flux is from the base of the transition region up into the corona, rather than the opposite. Under the circumstances mentioned above, the direction of the heat flow should be opposite to the gradient of the electron pressure gradient. Although the transition region is modeled as isobaric, this is only approximately true. Such a likely scenario makes the heat flow almost certainly to flow from the lower temperature base of the TR up into the incipient corona if a steady state current free expansion is to be maintained.

Scudder, J. D.↗
DOE OSTI2021

Effect of resistive wall on thermal quench in JET disruptions

In this paper, experimental data, simulations and theory are presented of a JET tokamak thermal quench. The emphasis is on the timescale of the bulk plasma thermal energy loss. The simulations suggest that the thermal energy loss is caused by a resistive wall tearing mode, and experimental data is consistent with this conclusion. The time scale of the thermal quench is the inverse of the mode growth rate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Impact of Temperature and Optical Error on the Combined Optical and Thermal Efficiency of Solar Tower Systems for Industrial Process Heat: Preprint

Concentrating solar thermal (CST) power towers can provide high flux concentrations at commercial scale. As a result, CST towers exhibit potential for high-temperature solar industrial process heat (SIPH) applications. However, at higher operating temperatures, thermal radiation losses can be significant. This study explores the trade-off between thermal and optical losses for SIPH applications using a collection of three case studies at operating temperatures that range from 900-1,550 degrees C. We assume blackbody radiation to represent the thermal losses at the receiver and we use ray tracing to estimate the optical losses. The results show the impact of process temperature on the maximum attainable system efficiency, as well as the higher flux concentration requirements as the temperature increases.

concentrating solar power↗
DOE OSTI2020

A thermodynamics-based damage model for the non-linear mechanical behavior of SiC/SiC ceramic matrix composites in irradiation and thermal environments

A damage model is developed and validated with experimental data for the non-linear mechanical behavior of SiC/SiC composite materials in nuclear applications. Cyclic thermal and mechanical loading associated with neutron irradiation effects of these composites leads to wide-spread and progressive micro-cracking that leads to loss of thermal conductivity and further enhancement of thermo-mechanical damage. A physics-based model of wide-spread micro-cracking is developed within the thermodynamic framework of continuum damage mechanics. Evolution equations for damage parameters that describe the growth of continuum damage are developed, where the material variables are obtained from experiments. The model novelty is in coupling mechanical, thermal, and irradiation damage through a consistent thermodynamic framework, including loss of thermal conductivity due to the evolution of mechanically induced micro-cracks. A number of thermo-mechanical experiments were conducted to confirm model assumptions. The model is shown to be validated with out-of-pile experiments, and then implemented using commercial finite element code COMSOL to the fuel cladding problem with normal and high radiation dose cases.

Materials Science↗
NASA NTRS1995

Effects of highly intermittent magnetic fields and plasma flows on solar wind dynamics

Filamentary magnetic fields and intermittent mass flows with highly variant physical parameters as observed in coronal holes provide, from a theoretical point of view, natural conditions for strongly nonlinear dynamics. The presence of sheared mass flows along fine scale magnetic structures results in strong nonlinear instability, most important of which is the explosive instability. We specify the physical conditions for several different manifestations of the onset of explosive instability and its further evolution: (1) fully developed explosive instability - explosive release of the energy; (2) shock formation - stabilization of instability by small scale spatial inhomogeneities leads to formation of subsequent shocks having a number of peculiarities that is determined by the interplay of thermal and viscous losses (for example, in predominance of thermal losses the isothermal jump occurs); and (3) solitary waves - stabilization of explosive instability by nonlinear dispersion effect leads to formation of a 'gas' of solitons which are later either damped away with characteristic time and energy input or evolve to solitons with explosively growing amplitudes. Each scenario is completely determined by the physical parameters of the medium, thus producing a quite uneven distribution of energy in a coronal hole and, respectively, an uneven outward propagation of the energy flux.

Ryutova, M.↗