Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Composition and automated crystal orientation mapping of rapid solidification products in hypoeutectic Al-4 at.%Cu alloys

Rapid solidification can produce metastable phases and unusual microstructure modifications in multi-component alloys during additive manufacturing or laser beam welding. Composition and phase mapping by transmission electron microscopy have been used in this paper to characterize the morphologically distinct zones developing in hypoeutectic Al-4 at.% Cu alloy after pulsed laser melting for different crystal growth rate regimes. Deviations of the compositions of the alloy phases from equilibrium predictions and unique orientation relationships between the solidification transformation products have been determined. Specifically, for the columnar growth zone at solidification rates of 0.8 m s - 1 < v < v a = 1.8 m s - 1 , two distinct orientation relationships were established between the concomitantly forming non-equilibrium phases, supersaturated α-Al solid solution and the discontinuously distributed α-Al 2 Cu-based θ'-phase, which can be described as {110} θ ∥ {001} α , [001] θ ∥ [110] α and {001} θ ∥ {001} α , [100] θ ∥ [100] α . These orientation relationships permit formation of coherent interphase interfaces with low interfacial free energy. Finally, this endows a kinetic advantage to the thermodynamically less stable θ'-Al 2 Cu phase relative to the more stable equilibrium θ-Al 2 Cu phase during formation of the morphologically modified eutectic of the columnar growth zone grains, since repeated nucleation is required to establish the discontinuous distribution of θ'-Al 2 Cu phase.

36 MATERIALS SCIENCE↗
DOE OSTI2017

The microstructure and composition of equilibrium phases formed in hypoeutectic Te-In alloy during solidification

As a key tellurium atoms evaporation source for ultraviolet detection photocathode, the hypoeutectic Te{sub 75}In{sub 25} alloy was prepared by employing a slow solidification speed of about 10{sup −2} K/s. The microstructure and chemical composition of the equilibrium phases formed in the as-prepared alloy were studied in this research work. The experimental results show that the as-prepared Te-In alloy was constituted by primary In{sub 2}Te{sub 5} phase and eutectic In{sub 2}Te{sub 5}/Te phases. The eutectic In{sub 2}Te{sub 5}/Te phases are distributed in the grain boundaries of primary In{sub 2}Te{sub 5} phase. With the slow solidification speed, a pure eutectic Te phase without any excessive indium solute was obtained, where Te content of eutectic Te phase is 100 mass%. Moreover, it can be considered that the stress between the In{sub 2}Te{sub 5} and Te phases plays an important role in reducing the tellurium vapor pressure in Te{sub 75}In{sub 25} alloy. - Highlights: • The microstructure of Te-In alloy as an evaporation source was analyzed. • A pure eutectic Te phase was obtained by using a slow solidification speed method. • The relation between vapor pressure and inner-stress in the alloy was discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Changing the solidification sequence and the morphology of iron-containing intermetallic phases in AA6061 aluminum alloy processed by spray forming

Highlights: • Spray forming alters the solidification path of the Fe contaminated AA 6061 alloy. • Thus forming primary α-Al{sub 15}(Fe, Mn){sub 3}Si{sub 2} with polyhedral morphology • Thus preventing the formation of AlFeSi with deleterious morphology • Despite Fe contamination final microstructure presented important ductility. - Abstract: Typically, aluminum alloys are contaminated by iron during recycling cycles. Such a procedure leads to the formation of intermetallic phases with detrimental morphology, which acts as stress risers, impairing mechanical properties and consequently hindering further mechanical processing and restricting recycling. This paper aimed at studying the solidification of an AA6061 alloy highly contaminated with iron (1.4 wt%). Spray forming processing allowed altering the solidification path of the Fe-modified AA 6061 alloy, resulting in the formation of primary α-Al{sub 15}(Fe, Mn){sub 3}Si{sub 2} phase with polyhedral morphology, which traps Fe and Si at elevated temperature. Furthermore, spray forming prevented the formation of intermetallic AlFeSi phases with platelet-like morphology, such as β-AlFeSi as well as the typical Chinese script morphology, resulting in a final ductile microstructure, allowing further processing by hot extrusion.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rapid Solidification Effects in Additively Manufactured Si and SiGe Compositions

SiGe alloys have a proven track record as robust high-temperature thermoelectric materials, powering NASA missions like SNAP-10A, LES-9, and Voyager 1 and 2. Enhancing thermoelectric efficiency hinges on minimizing thermal conductivity while preserving electrical conductivity. Rapid solidification via LPBF can generate microstructural features such as subgrain cellular boundaries and twinning, which may help reduce thermal conductivity while preserving semiconducting behavior. Here, this study investigates the potential of laser powder bed fusion (LPBF) additive manufacturing to fabricate nanostructured Si and SiGe thermoelectric materials. High cooling rates (10 5 to 10 7 K/s) rates inherent to the LPBF process are conducive to forming such nanostructures. Moreover, this fabrication technique could also be suitable for fabricating complex geometries needed to achieve improved device level performance. Process mapping of commercial Si powder with irregular morphology was first performed to understand the LPBF processing behavior of this semiconductor material. Subsequent studies included in-house synthesized B-doped (p-type) Si7 8 Ge 22 spherical powder that was produced via ultrasonic atomization. Scan strategies involved multiple laser exposures to mitigate solidification cracking: a high density of >98% was achieved, but solidification cracking could not be fully eliminated. Subsequently, a high electrical resistivity (i.e., low conductivity) was observed, but the measured Seebeck coefficient, ∼230 μV/K @ 500 °C, proved that good semiconductor material was being fabricated. A subgrain cellular structure (5–10 μm) was observed as defined by Ge segregation to the intercellular boundaries. The remelting strategies helped lower the cooling rates in processing SiGe, but this still resulted in high residual stresses, which induced a remarkably high density of twins (78–95%) to accommodate the deformation. This unique grain structure offers an avenue for phonon scattering and potential improvements in thermoelectric performance.

figure of merit↗
DOE OSTI2021

Metastable–solid phase diagrams derived from polymorphic solidification kinetics

Nonequilibrium processes during solidification can lead to kinetic stabilization of metastable crystal phases. A general framework for predicting the solidification conditions that lead to metastable-phase growth is developed and applied to a model face-centered cubic (fcc) metal that undergoes phase transitions to the body-centered cubic (bcc) as well as the hexagonal close-packed phases at high temperatures and pressures. Large-scale molecular dynamics simulations of ultrarapid freezing show that bcc nucleates and grows well outside of the region of its thermodynamic stability. An extensive study of crystal–liquid equilibria confirms that at any given pressure, there is a multitude of metastable solid phases that can coexist with the liquid phase. We define for every crystal phase, a solid cluster in liquid (SCL) basin, which contains all solid clusters of that phase coexisting with the liquid. Additionally, a rigorous methodology is developed that allows for practical calculations of nucleation rates into arbitrary SCL basins from the undercooled melt. It is demonstrated that at large undercoolings, phase selections made during the nucleation stage can be undone by kinetic instabilities amid the growth stage. On these bases, a solidification–kinetic phase diagram is drawn for the model fcc system that delimits the conditions for macroscopic grains of metastable bcc phase to grow from the melt. We conclude with a study of unconventional interfacial kinetics at special interfaces, which can bring about heterogeneous multiphase crystal growth. A first-order interfacial phase transformation accompanied by a growth-mode transition is examined.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2017

Comparative study of solute trapping and Gibbs free energy changes at the phase interface during alloy solidification under local nonequilibrium conditions

An analytical model has been developed to describe the influence of solute trapping during rapid alloy solidification on the components of the Gibbs free energy change at the phase interface with emphasis on the solute drag energy. For relatively low interface velocity V < V{sub D}, where V{sub D} is the characteristic diffusion velocity, all the components, namely mixing part, local nonequilibrium part, and solute drag, significantly depend on solute diffusion and partitioning. When V ≥ V{sub D}, the local nonequilibrium effects lead to a sharp transition to diffusionless solidification. The transition is accompanied by complete solute trapping and vanishing solute drag energy, i.e. partitionless and “dragless” solidification.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Microstructure development during rapid alloy solidification

Abstract Solidification processing of structural alloys can take place over an extremely wide range of solid–liquid interface velocities spanning six orders of magnitude, from the low-velocity constitutional supercooling limit of microns/s to the high-velocity absolute stability limit of m/s. In between these two limits, the solid–liquid interface is morphologically unstable and typically forms cellular-dendritic microstructures, but also other microstructures that remain elusive. Rapid developments in additive manufacturing have renewed the interest in modeling the high-velocity range, where approximate analytical theories provide limited predictions. In this article, we discuss recent advances in phase-field modeling of rapid solidification of metallic alloys, including a brief description of state-of-the-art experiments used for model validation. We describe how phase-field models can cope with the dual challenge of carrying out simulations on experimentally relevant length- and time scales and incorporating nonequilibrium effects at the solid–liquid interface that become dominant at rapid rates. We present selected results, illustrating how phase-field simulations have yielded unprecedented insights into high-velocity interface dynamics, shedding new light on both the absolute stability limit and the formation of banded microstructures that are a hallmark of rapid alloy solidification near this limit. We also discuss state-of-the-art experiments used to validate those insights. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2023

Outlook on texture evolution in additively manufactured stainless steels: Prospects for hydrogen embrittlement resistance, overview of mechanical, and solidification behavior

Abstract Realizing application specific manufacture with fusion-based additive manufacturing (F-BAM) processes requires understanding of the physical phenomena that drive evolution of microstructural attributes, such as texture. Current approaches for understanding texture evolution in F-BAM are majorly considerate of the phenomena occurring only during solidification. This hinders the comprehensive understanding and control of texture during F-BAM. In this perspective article, we discuss several physical phenomena occurring during and after solidification that can determine texture in F-BAM processed stainless steels (SS). A crystal plasticity-coupled hydrogen adsorption-diffusion modeling framework is also leveraged to demonstrate the prospects of grain boundary engineering with F-BAM for enhanced hydrogen embrittlement resistance of SS. Implications of varying thermokinetics in F-BAM for solidification behavior of SS are discussed. Additionally, microstructural attributes that are key to high temperature mechanical performance of SS are highlighted. Considerations as outlined in this perspective article will enable grain boundary engineering and application specific microstructural design of SS with F-BAM. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solidification of SRPPF Aqueous Recovery Liquid: Process Disruptions

Savannah River National Laboratory has identified a magnesium oxysulfate grout formulation to solidify the liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery System (ARS). The formulation uses reactive, light burnt MgO, anhydrous MgSO 4 , and dead burnt MgO and provides good mixability, similar density to the original Portland Cement-based mix, and a leachate pH of 9.39, within the assumed Waste Isolation Pilot Plant (WIPP) brine pH range. The formulation will solidify the effluent using a solid first, lost paddle design, within a 55-gallon drum. A series of seven different process disruptions, or irregular processing during the expected ARS liquid effluent solidification process, were completed to assess the severity of the impact of the process disruption and how the formulation behaves under these conditions. Seven process disruptions were investigated including: No Mixing, Partial Mixing, Compacted/Stratified, Sealed, Overfilled, Underfilled, and Undermixed. The impact on solidification, leachate pH, Er (a Pu/Am surrogate) distribution, and density of the resulting grout were established. Overall, four of the process disruptions, No Mixing, Partial Mixing, Compacted/Stratified, and Overfilled, resulted in basic, unabsorbed liquid that would require additional solidification to be acceptable for WIPP. Most solids generated in this testing met the expected WIPP leachate pH requirements. Solids from the Compacted/Stratified process disruption test, however, produced a leachate pH slightly above the assumed range in the WIPP performance assessment. The distribution of Er for most of the tests was relatively consistent. The No Mixing process disruption test, however, resulted in non-homogeneous Er distribution, indicating that radioactive material would not be evenly distributed throughout this solid’s matrix. The Overfilled test is the only mix with a density slightly below the acceptable value. The Sealed and Overmixed tests produced a solid closest to the standard mix with no unabsorbed liquid, expected leachate pH levels, consistent Er concentrations, and expected density, indicating these process disruptions do not have a negative impact on the final grout form. Based on the other process disruptions, it is critical to have premixed dry materials and a well-defined mixing process to produce a solid, homogeneous magnesium oxysulfate cement, with no unabsorbed liquid. These process disruption tests show that the lack of adequate mixing is fundamental to creating an improperly solidified material that may require remediation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Geometry-Dependent Solidification Regimes in Metal Additive Manufacturing

Recent modeling and experimental work in additive manufacturing has suggested that cross-sectional geometry may play a significant role in the local development of the solidification structure through its influence on the heat source path. This effect has been rationalized as the transition from a quasi-static point heat source regime, to a regime dominated by the quasi-static motion of an equivalent line source. This work provides a simple analytical framework for determining the conditions under which a system transitions between these regimes. Here, a transient semi-analytical heat transfer model is used to examine a wide range of process conditions and material properties. A simple analytical expression is derived and shown to accurately predict the transition between solidification regimes over these conditions. The functional form of this expression is then used to help understand the importance of various material properties, process parameters, and geometric factors on the characteristics of the solidification conditions. This approach may be used as a simple guideline for optimizing process conditions in response to variations in cross-sectional geometry to produce more consistent microstructural distributions in additively manufactured components.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser‐Powder Melt Pool Solidification Dynamics and Microstructural Engineering of Ti‐5553 Microlattices

The fine geometric and topological control afforded by additive manufacturing technologies has enabled the manufacture of architected materials across length scales, and enabling tunable mechanical performance as a function of local and global design. Progress has been made to tune the mechanical response of architected materials through geometry, but understanding how the geometry and processing conditions will inform the microstructure remains a challenge due to the rapid solidification in laser powder bed fusion. This study uses in situ X-ray imaging and electron backscatter diffraction microscopy to demonstrate that the melt pool size, microstructure morphology, and elastic strain distribution is influenced by a combination of lattice geometry and laser processing conditions. These results indicate that within larger melt pools the local thermal gradients are sufficient to enable a columnar-to-equiaxed transition across the melt pool. Furthermore, the solidification mechanisms producing these microstructures are examined across the first 5 ms of melting and solidification, described via in situ high-speed X-ray imaging and mirrored via multiphysics simulation.

additive manufacturing↗
DOE OSTI2023

Minor Elements and Solidification Cracking During Laser Powder-Bed Fusion of a High $\gamma ^{\prime }$ CoNi-Base Superalloy

Here, the cracking behavior of a high γ' volume fraction CoNi-base superalloy fabricated via laser powder bed fusion (LPBF) is studied in relation to the content of carbon and boron. Severe cracking occurred with the increase in boron content from 0.08 to 0.16 at. pct (0.015 to 0.029 wt pct), while compositions with 0.1 to 0.36 at. pct C (0.02 to 0.076 wt pct) and 0.08 at. pct B exhibited minimal cracking. Assessment of cracks in the high-boron composition shows a variation in crack density with printing parameters, and alignment of the cracks with the build direction. Scanning electron microscopy (SEM) of the crack surfaces shows evidence of a solidification cracking mode. Differential thermal analysis (DTA) reveals a decreased incipient melting temperature for the high-boron composition, and atom probe tomography (APT) is used to measure the enrichment at grain boundaries, revealing distinct boron segregation. Scheil-Gulliver solidification simulations for the different C and B levels are consistent with the incipient melting behavior observed with DTA. Evaluation of the solidification cracking susceptibility from the simulations allow for comparison of the CoNi alloy behavior to Ni-base superalloys studied for LPBF fabrication and displays how such metrics may aid in the design of new precipitation-strengthened superalloys for additive manufacturing (AM).

36 MATERIALS SCIENCE↗
DOE OSTI2017

Metastable solidification of hypereutectic Co 2 Si-CoSi composition: Microstructural studies and in-situ observations

Metastable solidification of undercooled Co 60 Si 40 melts was investigated by microstructural studies and in-situ high-energy X-ray diffraction. Five solidification paths were identified. Three of them were observed at low undercoolings, which show uncoupled and coupled growth of stable β-Co 2 Si and CoSi compounds. The other paths were observed at high undercoolings, which show peritectic and primary crystallization of a metastable Co 5 Si 3 compound. The β-Co 2 Si and Co 5 Si 3 compounds crystallize into a hexagonal crystal structure and experience solid-state decomposition. Microstructure formation depends on solidification path. The coupled and uncoupled growth of the stable compounds produces a regular lamellar eutectic structure and an anomalous eutectic structure, respectively. The crystallization and solid-state decomposition of the metastable Co 5 Si 3 compound brings about a fine-grained two-phase mixture, which represents another type of anomalous eutectic structure. Here, the results provide proof of two rare mechanisms of anomalous eutectic formation and shed light onto metastable phase relations in the undercooled region of the Co-Si system.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Multiscale dendritic needle network model of alloy solidification with fluid flow

We present a mathematical formulation of a multiscale model for solidification with convective flow in the liquid phase. The model is an extension of the dendritic needle network approach for crystal growth in a binary alloy. We propose a simple numerical implementation based on finite differences and step-wise approximations of parabolic dendritic branches of arbitrary orientation. Results of the two-dimensional model are verified against reference benchmark solutions for steady, unsteady, and buoyant flow, as well as steady-state dendritic growth in the diffusive regime. Simulations of equiaxed growth under forced flow yield dendrite tip velocities within 10% of quantitative phase-field results from the literature. Finally, we perform illustrative simulations of polycrystalline solidification using physical parameters for an aluminum-10wt% copper alloy. Resulting microstructures show notable differences when taking into account natural buoyancy in comparison to a purely diffusive transport regime. The resulting model opens new avenues for computationally and quantitatively investigating the influence of fluid flow and gravity-induced buoyancy upon the selection of dendritic microstructures. Further ongoing developments include an equivalent formulation for directional solidification conditions and the implementation of the model in three dimensions, which is critical for quantitative comparison to experimental measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Sensitivity of cellular automata grain structure predictions for high solidification rates

Understanding as-solidified grain structure development during constrained (G 0) alloy solidification conditions is a necessary component of understanding the larger process-microstructure relationships during additive manufacturing (AM) processing. This study applies a cellular automata (CA) model, for static solidification velocities and thermal gradients on the order of those expected in AM melt pools, to investigate grain shape development across ranges of input parameters governing temperature field evolution, nucleation, and growth. Variation in nucleated grain shape from columnar to equiaxed as a function of thermal gradient and nucleation density is modeled with CA and verified against the established transition model of Hunt and Gaumann. Furthermore, while thermal conditions and nucleation density are shown to have the largest roles on microstructure development, the sensitivity of grain structure was very unevenly distributed across parameter space. In particular, it was found that microstructure is very sensitive to mean nucleation undercooling and the interfacial response function in process space regimes near grain structure transitions, but entirely controlled by a combination of thermal gradient, solidification velocity, and nucleation density away from such transitions. The understanding of grain shape sensitivity obtained through CA modeling, particularly at large thermal gradient and nucleation density, will be necessary for accurate microstructure prediction during the extreme processing conditions and large input parameter uncertainty common to AM.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The timing of lunar solidification and mantle overturn recorded in ferroan anorthosite 62237

Ferroan anorthosite suite (FAS) rocks are widely interpreted to represent primordial lunar crust. Despite their importance in pinpointing the timing of lunar crust formation, robust chronological investigations for this rock type are scarce. Here, we report the Ar-Ar, Rb-Sr, and Sm-Nd isotopic systematics for the FAS troctolitic anorthosite 62237. The Ar-Ar isotopic system has been reset by a thermal event at 3710 ± 48 Ma, and the Rb-Sr isotopic systematics has been disturbed such that a Rb-Sr isochron age cannot be determined. However, an internal isochron for the Sm-Nd isotopic system has yielded an age of 4350 ± 73 Ma (MSWD = 2.0) with an initial ε 143 Nd CHUR of -0.53 ± 0.26. The mineral and whole-rock fractions of 62237 plot on the same internal isochron as FAS sample 60025. The combined datasets define an age of 4372 ± 35 Ma (MSWD = 4.0) with an initial ε 143 Nd CHUR of -0.17 ± 0.22. Literature Sm-Nd data for FAS and Mg-suite whole-rocks also plot on the 60025-62237 isochron. The coherence of data from both FAS and Mg-suite rocks examined thus far suggests that both rock suites formed contemporaneously from identical, or nearly identical, sources. In addition, the concordance of FAS and Mg-suite ages suggests that primordial crust solidification either involved both magmatic suites, or that Mg-suite magmatism was contemporaneous with FAS magmatism within resolution of the Sm-Nd chronometer. The ages for FAS and Mg-suite also coincide with the formation ages of the mare basalt source regions and urKREEP. Ferroan anorthosite suite rocks and urKREEP are thought to represent primordial LMO solidification products, whereas Mg-suite and the mare basalt source regions are argued to represent mixtures of various LMO crystallization products that were formed during density-driven overturn of the LMO. The concordance of ages implies that the 4372 ± 35 Ma Sm-Nd isochron records the age of mantle overturn, and that overturn occurred during, or shortly after, solidification of the LMO.

58 GEOSCIENCES↗
DOE OSTI2026

Enhancing microsegregation during rapid directional solidification through ternary microalloying

The nano-cellular dendritic microstructure formed during rapid directional solidification in powder bed fusion additive manufacturing creates unique properties such as simultaneous improvement in strength and ductility. However, process control of microsegregation features remains challenging due to low sensitivity of critical solidification mechanisms to process parameters. This study leverages microalloying to achieve large changes in dendrite composition, microstructure, and interdendritic zone width during laser powder bed fusion without modifying process parameters. CALPHAD simulations predict that the addition of Zr significantly steepens the solidus line of the dilute Cu-Cr alloy system, leading to enhanced Cr rejection into the melt and greater than 95% reduction in solubility of Cr in the solidified Cu matrix. Experimental validation using time-of-flight secondary ion mass spectrometry and Kelvin probe force microscopy reveals that the ternary alloy containing 0.01 wt% Zr exhibited wider interdendritic regions compared to the binary, a significantly higher number of Cr-rich particles within interdendritic regions, near-complete ejection of oxygen impurities from the matrix, and greater nanoscale work function contrast. These features indicate more aggressive Cr segregation in the presence of Zr and a purer Cu matrix and provide a potentially robust method for engineering the nano-cellular dendritic solidification microstructure.

CALPHAD↗