Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid moderator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

UO2 microstructural evolutions induced by Ni, Mo, and W dopants for intentional forensics

The concept of tagging nuclear fuel with a chemical barcode to enable forensics analysis across the nuclear fuel cycle is an area of active investigation, particularly to ensure fabrication viability without disrupting current fuel performance. This study explored the feasibility of using Ni, Mo, and W isotopic double-spikes as dopants in UO2 fuel from the perspective of fuel fabrication. Doped UO2 pellets were produced using conventional fuel fabrication processes, including powder mixing, sieving, pressing, and sintering in a reductive atmosphere. Two composition levels, 100 and 1000 ppm, were evaluated for each dopant element with isotopic double-spike configurations. For the Ni system, additional dopant concentrations of 250 and 500 ppm were produced with nonperturbed isotopic ratios. The results demonstrated that successful incorporation of Ni, Mo, and W double-spikes into UO2 pellets occurred with minimal shift in final density or dopant loss during pellet fabrication. Isotopic analysis confirmed the presence of the double-spike signature even when diluted with natural isotopic material in ratio of 1:5 in the fabrication process. Microstructural examinations revealed different impacts on grain size compared with undoped UO2. This study showed that Ni incorporation up to ∼500 ppm promoted moderate grain growth, whereas the Mo and W systems caused grain size reduction at all concentrations. Changes in the UO2 lattice parameter as a function of composition were detected exclusively for Ni up to 500 ppm, indicating that the Ni solid solution was the main factor for the observed grain growth. Insoluble (Mo and W) or supersaturated (Ni > 500 ppm) conditions produced grain size reduction. The Ni-doped pellets in the solution range resulted in a final microstructure within fuel specifications, demonstrating its potential benefits of employing complex dopant systems for potential nuclear forensic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Amorphous ZrCl 4 -Based Superionic Conductor as a Cost-Effective Solid Electrolyte for Batteries

Developing highly conductive and cost-effective solid electrolytes is essential for the commercialization of all-solid-state batteries (ASSBs). Zr-based halide electrolytes hold great promise due to their low estimated cost and high oxidation stability. However, the ionic conductivities of most of them are not high enough to enable moderate- and high-rate cycling of ASSBs. Here, fast ion transport is achieved in a group of cost-effective ZrCl 4 -based electrolytes via a design strategy to create highly disordered amorphous structures. Amorphous Li 0.8 ZrCl 4 (SO 4 ) 0.4 , with a low estimated cost of $21 kg –1 , achieves an ionic conductivity of 1.86 mS cm –1 at 25 °C. It also shows a high oxidation limit of 4.5 V vs Li/Li + and good compatibility with high-voltage cathodes, as demonstrated by the stable cycling of ASSBs (73.7% capacity retention after 1000 cycles at 1 C). Synchrotron X-ray diffraction, pair distribution function analysis, and electrochemical impedance spectroscopy reveal that the outstanding conductivity of these amorphous electrolytes is closely related to their short-range and medium-range ordering, revealing new insights for designing high-performance, cost-effective solid electrolytes.

Zhang, Guangxing [Georgia Institute of Technology,↗
DOE OSTI2024

Enhancing Acute Migraine Treatment: Exploring Solid Lipid Nanoparticles and Nanostructured Lipid Carriers for the Nose-to-Brain Route

Migraine has a high prevalence worldwide and is one of the main disabling neurological diseases in individuals under the age of 50. In general, treatment includes the use of oral analgesics or non-steroidal anti-inflammatory drugs (NSAIDs) for mild attacks, and, for moderate or severe attacks, triptans or 5-HT1B/1D receptor agonists. However, the administration of antimigraine drugs in conventional oral pharmaceutical dosage forms is a challenge, since many molecules have difficulty crossing the blood-brain barrier (BBB) to reach the brain, which leads to bioavailability problems. Efforts have been made to find alternative delivery systems and/or routes for antimigraine drugs. In vivo studies have shown that it is possible to administer drugs directly into the brain via the intranasal (IN) or the nose-to-brain route, thus avoiding the need for the molecules to cross the BBB. In this field, the use of lipid nanoparticles, in particular solid lipid nanoparticles (SLN) and nanostructured lipid carriers (NLC), has shown promising results, since they have several advantages for drugs administered via the IN route, including increased absorption and reduced enzymatic degradation, improving bioavailability. Furthermore, SLN and NLC are capable of co-encapsulating drugs, promoting their simultaneous delivery to the site of therapeutic action, which can be a promising approach for the acute migraine treatment. This review highlights the potential of using SLN and NLC to improve the treatment of acute migraine via the nose-to-brain route. First sections describe the pathophysiology and the currently available pharmacological treatment for acute migraine, followed by an outline of the mechanisms underlying the nose-to-brain route. Afterwards, the main features of SLN and NLC and the most recent in vivo studies investigating the use of these nanoparticles for the treatment of acute migraine are presented.

Torres, Joana (ORCID:0000000327276229)↗
DOE OSTI2023

An unstructured mesh based neutronics optimization workflow

We have developed a fully automated workflow to optimize the neutronics performance of the Second Target Station (STS) at the Oak Ridge National Laboratory’s Spallation Neutron Source. The optimization workflow starts with the parametrized solid CAD engineering models and converts them into the unstructured mesh (UM) models for the neutronics calculations with MCNP6.2. Calculations are executed and their results are loaded into the Dakota optimization toolkit. Dakota analyzes the results and proposes new geometry parameters for the next design iteration. The cycle repeats until the optimal parameters are found. The automated CAD to MCNP conversion, the use of high-fidelity UM models, and the use of modern optimizer are the key elements that advance the entire optimization workflow in comparison with the original workflow. The original workflow was based on a simplified constructive solid geometry (CSG) modeling with MCNPX, mcnp_pstudy tool, and an in-house optimizer. Herein to demonstrate the new workflow, we present a case of neutronics optimization of the moderator–reflector assembly (MRA). Apart from the MRA, the workflow can optimize other major STS components, such as the spallation target, neutron beamlines, radiation shielding, and various accelerator components. Importantly, the new workflow opens the door to the advanced multi-physics multi-parameter optimization and has the potential for use in other nuclear physics and accelerator applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Semiconducting High-Entropy Chalcogenide Alloys with Ambi-ionic Entropy Stabilization and Ambipolar Doping

Entropy stabilization is a novel materials-design paradigm to realize new compounds with widely tunable properties. However, almost all entropy-stabilized materials so far are either conducting metals or insulating ceramics, with a clear dearth in the semiconducting regime. Here, a new class of the multi-cationic and -anionic entropy-stabilized chalcogenide alloys based on the (Ge,Sn,Pb)(S,Se,Te) formula are synthesized and characterized experimentally. The con-figurational entropy from the disorder of both the anion and the cation sublattices reaches a record value of ~2.2 R mol -1 for the equimolar composition and stabilizes the single-phase solid solution. Theoretical calculations and experiments both show that the synthesized alloys are thermodynamically stable at the growth temperature and kinetically metastable at room temperature, segregating by spinodal decomposition at moderate temperatures. In conclusion, doping and electronic transport measurements verify that the synthesized materials are ambipolarly dopable semiconductors, which paves the way for the wider adoption of entropy-stabilized chalcogenide alloys in functional applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Scale-Up of Novel Li-Conducting Halide Solid State Battery Electrolyte

LBNL and project partner Saint Gobain (SG) demonstrated scalable processing of halide-based solid state batteries. SG’s innovative halide-based SSE utilized in this project is inherently scalable: it can be compressed into a dense electrolyte sheet at room temperature under moderate pressure, can be processed in dry air, and does not present any safety issues during processing or end use. The halide material forms the dense electrolyte layer, and is dispersed in the thick cathode to form a highly conductive path for Li ions. The halide also comes in contact with various environments and other materials (solvents, binders, processing equipment, etc.) throughout the battery manufacturing process, and must be stable in contact with cathode and anode materials during operation.

25 ENERGY STORAGE↗
DOE OSTI2021

Comparative analysis of various pretreatments to mitigate fouling and scaling in membrane distillation

Membrane distillation (MD) has shown strong promise for treating hypersaline produced water (PW) streams. Scaling and fouling on the membrane surface, however, have been identified as major challenges for commercialization and widespread application. The focus of this study was to first identify the nature of foulants and scalants on the membrane surface and then investigate the pretreatment strategies that mitigate the extent of fouling and scaling on the membrane surface. Vacuum MD (VMD) was selected for this study because of its higher flux at more moderate feed temperatures that eventually leads better assessment of fouling and scaling on the membrane surface. VMD flux tests were carried out with three different real PW samples at total dissolved solids concentrations in the range of 120-160 g/L. It was found that an efficient pretreatment prior to MD is required to mitigate the fouling potential of the organic matter, mostly suspended constituents, in PW samples. Suspended organics fouled and quickly wetted the MD membrane. Major conventional treatments, including filtration, oxidation, coagulation, air floatation, and aeration were investigated to pretreat the PW before VMD tests. A comprehensive comparative analysis is presented showing that the ultrafiltration and coagulation pretreatments displayed the best performance in mitigating the fouling and scaling, while oxidative pretreatment was found to be effective in reducing the iron concentration to less than 5 ppm. The surface of scaled membranes was carefully characterized to further evaluate the performance of each pretreatment. The components that had the highest tendency to precipitate on the membrane surface were identified as strontium sulfate, calcium carbonate, sodium chloride, iron oxide, and silica. In closing, these findings are supported by thermodynamic estimation of the saturation index.

42 ENGINEERING↗
DOE OSTI2021

Polymers in molten inorganic salt hydrate phase change materials: solubility and gelation

Inorganic salt hydrates are of interest as phase change materials (PCMs) for thermal energy storage because of their unique properties, such as high latent heats of fusion, moderate melting temperatures, high volumetric energy storage densities, and enhanced thermal conductivities compared to their organic counterparts. Because of the low viscosities of molten salt hydrates, the leakage and settling of solids can easily occur during their application. Polymers are promising candidates for preventing these issues. In addition, the non-flammability, non-volatility, and nontoxicity of many molten salt hydrates make them attractive options as “green” solvents for polymers. However, solutions of polymers in molten salt hydrates have rarely been studied and are poorly understood. The highly ionic environments in these materials created due to a scarcity of hydration water for ions leads to strong ionic interactions, with ramifications for polymer solubility and chain expansion. This Perspective article aims to focus on polymer solutions and gels in inorganic salt hydrates by comparing these systems with existing knowledge of polymers in traditional ionic liquids and aqueous salt solutions. To provide insight into the states of ions and water in molten salt hydrates and the degree of hydration of polymers in these solvents, infrared spectroscopy experiments have been performed, and the data are correlated with the temperature-responsive gelation of poly(vinyl alcohol), one candidate material currently used for the shape stabilization of inorganic PCMs. Finally, the thermal properties of inorganic salt hydrates and ionic liquids are compared and strategies for the shape stabilization of inorganic salt hydrates using polymers, through the formation of physical gels, are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A novel in-situ Raman spectroscopic cell for aqueous geochemistry at the solid–liquid interface

In-situ Raman spectroscopy has the potential to be a powerful technique for monitoring geochemical reactions at a solid–liquid interface in real time. In this article, we present the development and testing of an in-situ Raman spectroscopic cell, which can be used for reaction systems at moderate temperatures and pressure [<1000 psi (6.89 MPa), <100 °C, relevant to subsurface geologic systems] and can hold samples large enough for chemical mapping of heterogeneous rock surfaces. The system is validated by measuring the temperature-dependent conversion of gypsum to calcite over time. Near total conversion of gypsum to calcite on the mineral surface took 29 hours at room temperature and 150 minutes at 100 °C, corresponding to an 11.6-fold increase in the conversion rate. Further, we anticipate that this cell can be an important tool in quantifying the rates of carbon mineralization relevant to geologic carbon sequestration, particularly for the elevated rates recently observed in mafic/ultramafic rocks.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Impact of reservoir parameters and wellbore permeability uncertainties on CO 2 and brine leakage potential at the Shenhua CO 2 Storage Site, China

Here, this paper describes a system-level risk assessment for the Shenhua CO 2 storage site, China, using the National Risk Assessment Partnership Integrated Assessment Model for Carbon Storage (NRAP-IAM-CS). Here, we begin by determining the optimal number of Monte Carlo (MC) simulations to achieve CO 2 and brine leakage result convergence. Then, we calculate mass CO 2 and brine leakage to the atmosphere and a hypothetical shallow aquifer. Finally, we assess the geochemical impacts in the event of leakage as if there were a shallow freshwater aquifer at the Shenhua site. Simulation results show that leakage results tend to stabilize after 300 Monte Carlo simulations. When the three wells on site are assigned a permeability of 10 -11 m 2 (representing significantly leaking wells), moderate CO 2 and brine leakages occur, and the percentage of CO 2 leakage exceeds the threshold value we set based on the Intergovernmental Panel on Climate Change (IPCC). This is, however, unlikely to be the case for the Shenhua site. For all the other scenarios, the CO 2 leakage is trivial although there is still the possibility of CO 2 leakage into the groundwater aquifer exceeding the 1% threshold over 1000 years, assuming constant legacy wellbore permeability. For the significantly leaking scenario, there is a 10% probability to have a moderate (2.7 × 10 7 m 3 ) leakage-affected volume in the shallow aquifer with the pH below 6.5, and a large (1.4 × 10 8 m 3 ) volume with the total dissolved solids (TDS) above 500 ppm, hence pH and TDS may be considered for site monitoring plans. Based on the simulation results, there is a very low probability of significant CO 2 /brine leakage through the existing wells at the Shenhua CO 2 storage site.

58 GEOSCIENCES↗
DOE OSTI2026

Photoelectrode Durability in Two- versus Three-Electrode Configurations: Understanding the Impact of Circuit Configuration on Water-Splitting Stability

Device durability remains a significant challenge in photoelectrochemical (PEC) water splitting under ambient conditions. Yet, a lack of understanding of the test configuration and applied bias effects continue to hinder progress. In this study, we differentiate two-electrode (2E) and three-electrode (3E) configurations for evaluating PEC material durability, focusing particularly on their impacts on photoabsorber solid-state operating conditions. Our results underscore the fallacy of inferring 2E device stability from durability measurements performed solely in 3E configurations. Unmeasured and often misunderstood total circuit bias in 3E tests moderates material degradation, leading to the overestimation of photoelectrode stability compared to short-circuit operation. We demonstrate how the photoabsorber's operating voltage critically governs charge separation, surface stability, and degradation mechanisms during PEC operation. With these findings, we propose a standardized framework for conducting more reliable 3E durability experiments that simulate unassisted performance to help accelerate the development of robust, stable materials for solar-driven water splitting.

08 HYDROGEN↗
DOE OSTI2020

Microreactor Agile Nonnuclear Experimental Testbed Test Plan

Microreactors are an attractive technology option for kick-starting nuclear innovation if they can be operated at high temperature, yielding high power conversion thermal efficiencies comparable or better than in commercial light water reactors. Microreactors are currently the smallest variation of Small Modular Reactors (SMRs). SMRs are “newer generation reactors designed to generate electric power up to 300 MWe and whose components and systems can be shop-fabricated and then transported as modules to the sites for installation as demand arises.” (IAEA, 2016). Vendors are developing microreactor designs to provide an affordable, potentially mobile source of electricity - see Fig. 1 for an example of a microreactor on a semi-truck. Various microreactor designs are possible including heat pipe- and gascooled options, which are the focus of the nonnuclear testing described in this document. In heat pipe microreactors, high-temperature heat pipes using liquid sodium or potassium working fluid transport fission heat from the core to a heat removal section which in turn transfers heat to the power conversion system working fluid. In a gas-cooled design, He or other gas will flow through a solid monolith of material and transfer heat as the temperature of the gas increases through a heat exchanger to a power conversion unit. The logistics of all these processes will be examined and tested through a series of articles at the nonnuclear test bed at Idaho National Laboratory (INL), the Microreactor Agile Nonnuclear Experiment Testbed (MAGNET) facility. Microreactors designed to produce power of 0.1-20 MWt offer the potential for more affordable nuclear energy for a range of applications. In a heat pipe microreactor, heat pipes, fuel rods, and/or moderator are intermixed in the reactor core assembly. Heat pipes extend from the core region into the heat removal section where the power conversion unit working fluid flows through holes or channels, transferring heat from the heat pipes to the working fluid. In a gas-cooled microreactor, gas flows through the solid monolith region and up into the heat exchanger region, transferring heat to the working fluid. For initial testing, the heat removal working fluid can be a low pressure gas for testing that addresses thermal stresses. In the final application, heat addition to the power conversion working fluid typically occurs at high pressure, supporting operation of an air-Brayton, supercritical CO 2 (SCO2), or He-recuperated Brayton cycle. Various stages of the steps above will be demonstrated through the tests described in this report.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Selective mass scaling for single-layer thick shell elements in DYNA3D

Hexahedral elements can be adapted to model thin and moderately thick structures by neglecting the coupling of through-thickness stress, resulting in a fully three-dimensional, but simplified, state of stress. These specialized elements, often referred to as “thick” or “solid” shells, are generally employed to model thin-walled structures using continuum mechanics-based material models. In explicit dynamics simulations, where computational speed is important, these elements are integrated with a single quadrature point and a set of anti-hourglassing (stabilizing) forces. Thick shells, by definition, have a thickness dimension smaller than their in-plane dimensions, and this small thickness often determines the stable time step size in simulations, despite the mechanics being approximated. To alleviate this limitation while retaining the relevant dynamics of thin-walled structures, selective mass scaling (SMS), or selective mass “augmentation,” has been proposed in the literature. In this technical report, we explore the application of SMS to single-layer thick shells in the simulation software DYNA3D.

42 ENGINEERING↗
DOE OSTI2022

Evolution of structure and transport properties of the Ba 8 Cu 16 P 30 clathrate-I framework with the introduction of Ga

Two type-I clathrates were synthesized by introducing Ga into the framework of the Ba 8 Cu 16 P 30 type-I clathrate. The introduction of minute amounts of Ga, 1.9% Ga/M total (where M total = Cu + Ga), resulted in the disturbance of the completely ordered Pbcn superstructure of Ba 8 Cu 16 P 30 . Ba 8 Cu 15.43(2) Ga 0.3 P 30.26(3) crystallizes in a partially ordered orthorhombic Pmna clathrate-I superstructure with five out of 15 framework sites being jointly occupied by metal+phosphorus. Increasing the Ga content resulted in all framework sites being occupied by metal + phosphorus in the archetype cubic Pm n clathrate-I crystal structure of Ba 8 Cu 14.5(3) Ga 1.3 P 30.2(4) with 8.2% Ga/M total . A combination of energy dispersive x-ray spectroscopy, inductively coupled plasma mass spectroscopy, and single crystal x-ray diffraction was used to determine the structures alongside the compositions. The positional disorder was verified by 31 P solid state NMR spectroscopy. Characterization of the transport properties indicated that the Ga-substituted samples exhibit higher Seebeck coefficients and electrical resistivities compared to its pristine counterpart, in line with the expected reduction of the hole concentration due to Ga/Cu substitution. Moderate improvements in the thermoelectric power factor and overall figure-of-merit were observed for samples with 6.9% and 3.8% Ga/M total as compared to those for the pristine Ba 8 Cu 16 P 30 clathrate. Finally, band structure calculations shed light on how Ga substitution affects the electronic structure and thermoelectric properties of studied clathrates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Phosphonate functionalized magnetic mesoporous silica for rare earth element recovery from citrate assisted solid waste extracts

The growing high demand of rare earth elements (REEs) has prompted extensive research on REE recovery from waste streams. This study reports the synthesis and evaluation of phosphonate-functionalized magnetic mesoporous silica (MMS-PP) for REE recovery from the acidic extracts of solid wastes. MMS-PP was synthesized using surfactant template and post-synthesis methods, and tested using simulated and real extraction solutions from citrate-assisted REE extracts from municipal solid waste incineration (MSWI) ash. The organic-inorganic hybrid MMS-PP was evaluated for La recovery from 50 mM simulated citrate extract, with the adsorption capacity of 13.5 mg/g compared to ∼2.5 mg/g for non-functionalized MMS. The MMS-PP material exhibited fast adsorption within 10 min, good La selectivity against competing Na + and Ca 2+ , moderate selectivity against Al 3+ and Fe 3+ , high recyclability over multiple adsorption-desorption cycles, and equivalent efficiency for La, Ce, Nd, and Y recovery. Furthermore, the MMS-PP material also demonstrated 70–95% REE recovery from real citrate extracts of MSWI ash, and the spent MMS-PP material can be regenerated and reused for multiple cycles. Functionalized mesoporous materials in combination with organic-ligand assisted extraction can potentially provide a green, effective, and tunable solid-liquid separation platform for REE recovery from complex solid waste streams.

REE recovery↗
DOE OSTI2022

Benchmarking Solid-State Batteries Containing Sulfide Separators: Effects of Electrode Composition and Stack Pressure

Integrating sulfide separators into solid-state batteries (SSBs) containing high energy cathodes typically requires one or more materials and engineering solutions including: (i) applying interfacial coatings to mitigate electrolyte decomposition, (ii) applying high stack pressures to form robust solid-solid contacts, and (iii) using alloying anodes to avoid Li dendrite formation. Despite the promise of these approaches, a lack of standardized testing protocols makes it difficult to directly compare results among different studies. To address this problem, the present work benchmarks the performance of SSBs containing β-Li 3 PS 4 (LPS) separators and composite cathodes. By systematically varying the anode/cathode composition and stack pressure, this work demonstrates that cathode design is a major bottleneck for solid-state cells cycled at low rates (<100 µA cm -2 ). Operando stack pressure measurements show that, while mechanical confinement generally promotes higher active material utilization and cycling stability, this strategy alone does not address interfacial reactivity between LPS and high voltage cathodes. Here, these results also demonstrate that stress evolution during cycling is dominated by volume changes at the Li metal anode. Finally, we show that FeS 2 cathodes with moderate operating voltages (<3 V vs Li/Li + ) exhibit superior cycling performance compared to high voltage cathodes by facilitating formation of stable cathode/electrolyte interfaces.

25 ENERGY STORAGE↗
DOE OSTI2025

Thermodynamic Modeling of Complex Solid Solutions in the Lu-H-N System via Graph Neural Network Accelerated Monte Carlo Simulations

Metal hydrides are important across diverse applications, such as hydrogen storage, batteries, gas sensors, nuclear reactions, and high-temperature superconductivity. Previous computational studies of metal hydrides under extreme pressures, e.g., 𝑂⁡(10 2 ) ⁢GPa, usually treat them as stoichiometric compounds without considering interstitial lattice disorder. As pressures become more moderate in the 𝑂⁡(10 0 ) ⁢GPa and below range, hydrogen disorder at interstitial lattice sites becomes prominent, e.g., in the N-doped Lu hydride that was recently claimed superconducting near 1 GPa. Further adding compositional complexity from alloying and/or multielement interstitial occupation makes elucidating pressure- and temperature-dependent observables intractable by first-principles calculations alone. We therefore propose a lattice graph neural-network surrogate modeling approach to predict configuration- and pressure-dependent equation-of-state properties. Their efficiency permits Monte Carlo simulations to calculate Gibbs energies and pressure-dependent phase diagrams, thereby revealing insights into the synthesis conditions required for achieving desired phase equilibria. We demonstrate this concept for the compositionally complex cubic Lu(H,N,Va) 3 system where three constituents (hydrogen, nitrogen and vacancy) have disordered multielement interstitial occupancies and insights into pressure-dependent phase equilibria are critically needed, e.g., N-doping levels can significantly lower dehydrogenation temperatures and provide a new strategy to optimize hydrogen-storage alloys. This work can improve the thermodynamic understanding of the Lu-H-N system and help rational synthesis of N-doped Lu hydrides, but more generally demonstrates an efficient approach to model pressure-dependent thermodynamics of multicomponent solid solutions.

Monte Carlo methods↗
DOE OSTI2025

Spin‐Orbit Effects in a Thallium Borohydride Stabilized by Coordination to Bis(diisopropylamino)Cyclopropenylidene (BAC)

The reaction of Tl(OTf) with 2 equiv of bis(diisopropylamino)cyclopropenylidene (BAC) in THF results in formation of [Tl(BAC) 2 (OTf)] (1) in moderate yields. Subsequent reaction of 1 with [K][H 2 -9-BBN] ([H 2 -9-BBN] − = dihydrido 9-boratabicyclo[3.3.1]nonane) in THF results in formation of [Tl(BAC)(μ-H 2 -9-BBN)] 2 (3), also in moderate yield. Complex 3 is the first reported thallium borohydride. We attribute its thermal stability to the strong donor ability of the BAC co-ligand. Both 1 and 3 exhibit trigonal pyramidal geometries about Tl + in the solid-state, indicative of the presence of stereochemically active lone pairs. The hydride environment in 3 is calculated to exhibit a 3.9 ppm downfield shift attributed to spin-orbit effects from the adjacent Tl center.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗