Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solar cell defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Defect studies in one MeV electron irradiated GaAs and in Al/sub x Ga/sub l-x As P-N junction solar cells

Deep level transient spectroscopy reveals that the main electron traps for one-MeV electron irradiated GaAs cells are E9c)-0.31, E(c)-0.90 eV, and the main hole trap is due to the level. Electron trap density was found to vary from 3/tens-trillion ccm for 2/one quadrillion cm 3/3.7 quadrillion cm for 21 sextillion cm electron fluence for electron fluence; a similar result was also obtained for the hole trap density. As for the grown-in defects in the Al(x)Ga(1-x)As p-n junciton cells, only two electron traps with energies of E(c)-0.20 and E(c)-0.34 eV were observed in samples with x = 0.17, and none was found for x 0.05. Auger analysis on the Al(x)Ga(1-x) As window layer of the GaAs solar cell showed a large amount of oxygen and carbon contaminants near the surface of the AlGaAs epilayer. Thermal annealing experiment performed at 250 C for up to 100 min. showed a reduction in the density of both electron traps.

Li, S. S.↗
DOE OSTI2025

How non-ohmic contact-layer diodes in perovskite pinholes affect abrupt low-voltage reverse-bias breakdown and destruction of solar cells

Perovskite solar cells (PSCs) rapidly degrade under reverse bias, a condition that may occur during partial shading. Here, in this study, we use electrical measurements, electron microscopy, and optical and thermal imaging to investigate abrupt breakdown and hotspotting under low reverse potentials (<|-2| V). We show that microscopic pinholes in the perovskite layer cause rapid, destructive breakdown under reverse bias despite minimally reducing power conversion efficiencies. Measurements on miniature (200-micrometer diameter) PSCs and perovskite-free transport-layer diodes indicate that abrupt, low-voltage breakdown occurs in nanoscale to micrometer-scale defects and that metal migration and filamentation are unlikely causes. Reverse-bias stability substantially improves when pinholes in the perovskite and transport layers are eliminated. Atomic layer deposition of tin oxide prevents abrupt breakdown by ensuring physical separation between electrodes-not by blocking metal ion migration. Perovskite researchers should adopt cleaner, more uniform deposition techniques to enable robust PSCs for further research and commercial applications.

14 SOLAR ENERGY↗
DOE OSTI2025

Increased Voltage in CdSe Solar Cells by Mitigation of Charge Carrier Trapping Due to Se Vacancies

Cadmium selenide (CdSe), with a 1.7 eV bandgap, is a promising high-bandgap semiconductor for tandem solar cells, yet device efficiencies are hindered by rapid minority carrier recombination. Here, in this study, polycrystalline CdSe solar cells are investigated using radiative emission spectroscopy, time-resolved photoluminescence, and density functional theory, revealing fast (sub-nanosecond) minority carrier trapping by selenium vacancy-related defect states with densities of (5–50) × 10 17 cm −3 , limiting carrier mobility and increasing recombination. By reducing absorber thickness to ≈0.5 µm, trapping effects are mitigated, achieving a record open-circuit voltage of 917 mV, a 165 mV improvement over prior reports. These findings clarify the role of Se vacancies in limiting CdSe solar cell performance and provide insights applicable to CdSe and CdSeTe thin-film photovoltaics. This work advances understanding of defect-mediated losses in II–VI semiconductors and suggests pathways for improving solar cell performance through defect control.

14 SOLAR ENERGY↗
DOE OSTI2024

Surface Passivation to Improve the Performance of Perovskite Solar Cells

Perovskite solar cells (PSCs) suffer from a quick efficiency drop after fabrication, partly due to surface defects, and efficiency can be further enhanced with the passivation of surface defects. Herein, surface passivation is reviewed as a method to improve both the stability and efficiency of PSCs, with an emphasis on the chemical mechanism of surface passivation. Various molecules are utilized as surface passivants, such as halides, Lewis acids and bases, amines (some result in low-dimensional perovskite), and polymers. Multifunctional molecules are a promising group of passivants, as they are capable of passivating multiple defects with various functional groups. This review categorizes these passivants, in addition to considering the potential and limitations of each type of passivant. Additionally, surface passivants for Sn-based PSCs are discussed since this group of PSCs has poor photovoltaic performance compared to their lead-based counterpart due to their severe surface defects. Lastly, future perspectives on the usage of surface passivation as a method to improve the photovoltaic performance of PSCs are addressed to provide a direction for upcoming research and practical applications.

14 SOLAR ENERGY↗
NASA NTRS1981

Silicon solar cell process development, fabrication, and analysis

Two large cast ingots were evaluated. Solar cell performance versus substrate position within the ingots was obtained and the results are presented. Dendritic web samples were analyzed in terms of structural defects, and efforts were made to correlate the data with the performance of solar cells made from the webs.

Yoo, H. I.↗
NASA NTRS1971

Radiation damage annealing kinetics

Various spectral response studies are reported that assess lithium doping effects on the recovery process of electron damaged silicon solar cells. Measurements of both the minority carrier lifetimes and the energy level spectrum of the defects are used to predict lifetime damage constants and carrier removal rates relevant to the operation of the solar lithium-doped cell and its annealing kinetics.

Dresselhaus, M. S.↗
NASA NTRS2001

Annealing of Solar Cells and Other Thin Film Devices

Annealing is a key step in most semiconductor fabrication processes, especially for thin films where annealing enhances performance by healing defects and increasing grain sizes. We have employed a new annealing oven for the annealing of CdTe-based solar cells and have been using this system in an attempt to grow US on top of CdTe by annealing in the presence of H2S gas. Preliminary results of this process on CdTe solar cells and other thin-film devices will be presented.

Escobar, Hector↗
NASA NTRS1995

High and low energy proton radiation damage in p/n InP MOCVD solar cells

InP p(+)nn(+) MOCVD solar cells were irradiated with 0.2 MeV and 10 MeV protons to a fluence of 10(exp 13)/sq cm. The degradation of power output, IV behavior, carrier concentration and defect concentration were observed at intermediate points throughout the irradiations. The 0.2 MeV proton irradiated solar cells suffered much greater and more rapid degradation in power output than those irradiated with 10 meV protons. The efficiency losses were accompanied by larger increases in the recombination currents in the 0.2 MeV proton irradiated solar cells. The low energy proton irradiations also had a larger impact on the series resistance of the solar cells. Despite the radiation induced damage, the carrier concentration in the base of the solar cells showed no reduction after 10 MeV or 0.2 MeV proton irradiations and even increased during irradiation with 0.2 MeV protons. In a DLTS study of the irradiated samples, the minority carrier defects H4 and H5 at E(v) + 0.33 and E(v) + 0.52 eV and the majority carrier defects E7 and E10 at E(c)- 0.39 and E(c)-0.74 eV, were observed. The defect introduction rates for the 0.2 MeV proton irradiations were about 20 times higher than for the 10 MeV proton irradiations. The defect E10, observed here after irradiation, has been shown to act as a donor in irradiated n-type InP and may be responsible for obscuring carrier removal. The results of this study are consistent with the much greater damage produced by low energy protons whose limited range causes them to stop in the active region of the solar cell.

Rybicki, George↗
DOE OSTI2025

Controlling Preferred Grain Orientation in Vapor-Deposited Metal-Halide Perovskite Thin Films

Metal-halide perovskites are promising semiconductor materials for light-absorber layers in solar cells due to their optimized band gap, defect tolerance, and relative ease of synthesis. In this work, we demonstrate the viability of vapor transport deposition (VTD), a solvent-free processing method, to realize polycrystalline films of both lead iodide (PbI 2 ) and methylammonium lead iodide (MAPbI 3 ) perovskites showing preferential crystallographic orientation. Notable is the difference in perovskite film texturing observed for sequentially and co-deposited VTD films of MAPbI 3 , as well as the lack of strong preferential orientation in solution-processed MAPbI 3 films. While sequential deposition of the perovskite precursors PbI 2 and methylammonium iodide (MAI) leads to a MAPbI 3 film with a limited preferential grain orientation, co-deposited MAPbI 3 films mirror the orientation of excess PbI 2 present in the film. The latter is confirmed by the similar dependence of preferential orientation for PbI 2 and co-deposited MAPbI 3 on underlayer roughness, as well as the emergence of preferential orientation in MAPbI 3 only when excess PbI 2 is present. Both MAPbI 3 and PbI 2 films show a strong preferred lattice orientation on smooth substrates, while on rougher substrates, this orientation is disrupted. Furthermore, these results are interpreted as excess PbI 2 frustrating the diffusion of MAI in the film, which would otherwise disrupt the preferred orientation, pointing to a notable difference in lattice orientation arising from processing technique and conditions.

Deposition↗
NASA NTRS1980

Photodegradation in silicon

The state of knowledge concerning the following defects in silicon is briefly surveyed: substitutional impurities; vacancy-related defects; interstitial-related defects; defect pairs. Although a great deal is known, it is argued that not enough is yet known to model radiation damage production in the bulk or in the vicinity of the junction of a solar cell. The results on photon degradation (and enhancement) of solar cells are then reviewed, and it is suggested that defect pairs may be the defects responsible. Mechanisms for photon-induced dissociation of pairs are discussed but a more detailed understanding awaits the identification of the actual defects.

Corbett, J. W.↗
NASA NTRS1983

Analysis of defect structure in silicon. Characterization of SEMIX material. Silicon sheet growth development for the large area silicon sheet task of the low-cost solar array project

Statistically significant quantitative structural imperfection measurements were made on samples from ubiquitous crystalline process (UCP) Ingot 5848 - 13C. Important correlation was obtained between defect densities, cell efficiency, and diffusion length. Grain boundary substructure displayed a strong influence on the conversion efficiency of solar cells from Semix material. Quantitative microscopy measurements gave statistically significant information compared to other microanalytical techniques. A surface preparation technique to obtain proper contrast of structural defects suitable for quantimet quantitative image analyzer (QTM) analysis was perfected and is used routinely. The relationships between hole mobility and grain boundary density was determined. Mobility was measured using the van der Pauw technique, and grain boundary density was measured using quantitative microscopy technique. Mobility was found to decrease with increasing grain boundary density.

Natesh, R.↗
DOE OSTI2024

CIGS Technology Advancement via Fundamental Modeling of Defect/Impurity Interactions (Final Technical Report)

The primary goals of the proposed work were to provide modeling tools (and the associated insight which comes along with model development) for design and optimization of CuIn x Ga 1-x Se 2 (CIGS) and CdSeTe (CST) solar cell manufacturing processes and to establish the foundation for comprehensive end-to-end predictive modeling tools to enable optimization of thin film photovoltaic technology for performance, cost, yield, and reliability. The initial focus of efforts within this project was to develop coupled process/optical/device models for CIGS PV technology and to work with Siva Power to apply that TCAD (technology computer-aided design) system to improve the efficiency and reduce manufacturing costs for CIGS solar cells. Our approach to that end was to generate an extensive database of DFT calculations and to use those calculations via statistical thermodynamics methods and Monte Carlo simulation to develop and characterize models for the behavior of native defects as well as intentional and unintentional impurities, including the redistribution of the primary components of CIGS films. Increased effort went toward coupling those models for defect behavior and composition evolution to the performance of multicrystalline CIGS solar cells via prediction of doping level and recombination lifetime as function of manufacturing process. In the second budget period, the project pivoted to developing a similar system for the CdSeTe system, focused especially on understanding the role of Se/Te alloy concentration. Execution of the project resulted in the successful development of TCAD systems for both CIGS and CdSeTe thin film PV within the Synopsys Sentaurus framework by utilizing the Alagator interface. In the first budget period of the project, we developed quantitative models for the major components of CIGS PV and implemented them within a framework that couples process, optical, and device simulation. From the insights we have gained, we identified novel opportunities for enhancing CIGS solar cell performance and have laid the groundwork to further optimize the layer structure, composition profile, and thermal cycles for substantially improved efficiency and lower manufacturing costs. For the CIGS system, process changes to achieve greater than 1% absolute enhancement in efficiency were identified, but testing of those approaches was stymied by lack of a domestic CIGS manufacturing partner after the closure of Siva Power as well as Miasole. For CdSeTe, a fully capable TCAD system only became ready to apply near the end of the project period, so substantial opportunities remain to apply those models to enhance the leading thin film PV technology.

14 SOLAR ENERGY↗
NASA NTRS1978

Effect of copper impurity on polycrystalline silicon solar cells

The presence of copper impurity, up to 10 to the 15th atoms/cc, in single crystal silicon has been shown to have no deleterious effect on the p-n junction solar cell performance. However, in polycrystalline silicon, copper atoms tend to migrate to the defect sites because of the structural sensitive properties of copper. This study was undertaken to investigate the influence of this behavior of copper impurity on the performance of p-n junction solar cells fabricated from structurally imperfect silicon. Two sets of polycrystalline silicon substrates containing copper were examined. In one set of samples, copper was incorporated during growth, whereas in the other, copper was diffused. Solar cells were fabricated on both the sets of substrates by a standard process. Dark and light I-V and spectral response characteristics of the cells were measured and compared with copper-free polycrystalline silicon solar cells. The results and the model are discussed.

Daud, T.↗
NASA NTRS1995

High and Low Energy Proton Radiation Damage in p/n InP MOCVD Solar Cells

InP p(+)/n/n(+) solar cells, fabricated by metal organic chemical vapor deposition, (MOCVD) were irradiated with 0.2 MeV and 10 MeV protons to a fluence of 10(exp 13)/sq cm. The power output degradation, IV behavior, carrier concentration and defect concentration were observed at intermediate points throughout the irradiations. The 0.2 MeV proton-irradiated solar cells suffered much greater and more rapid degradation in power output than those irradiated with 10 MeV protons. The efficiency losses were accompanied by larger increases in the recombination currents in the 0.2 MeV proton-irradiated solar cells. The low energy proton irradiations also had a larger impact on the series resistance of the solar cells. Despite the radiation induced damage, the carrier concentration in the base of the solar cells showed no reduction after 10 MeV or 0.2 MeV proton irradiations and even increased during irradiation with 0.2 MeV protons. In a deep level transient spectroscopy (DLTS) study of the irradiated samples, the minority carrier defects H4 and H5 at E(sub v) + 0.33 and E(sub v) + 0.52 eV and the majority carrier defects E7 and El0 at E(sub c) - 0.39 and E(sub c) - 0.74 eV, were observed. The defect introduction rates for the 0.2 MeV proton irradiations were about 20 times higher than for the 10 MeV proton irradiations. The defect El0, observed here after irradiation, has been shown to act as a donor in irradiated n-type InP and may be responsible for obscuring carrier removal. The results of this study are consistent with the much greater damage produced by low energy protons whose limited range causes them to stop in the active region of the solar cell.

Rybicki, George↗
DOE OSTI2026

Quantification of Shallow Defect Suppression in Aminosilane-Passivated Lead Halide Perovskites via Optical and Electrochemical Methods

We combine fluence-dependent photoluminescence (PL) and electrochemical characterization to estimate defect-dependent trapping rates, energetic distributions, and densities of defects, in lead halide perovskite films Cs 0.1 FA 0.9 PbI 3 and Cs 0.17 FA 0.83 Pb­(I 0.75 Br 0.25 ) 3 , before and after trap passivation with vapor-deposited (3-aminopropyl)­trimethoxysilane (APTMS). For both compositions, the PL studies show that energetically shallow subgap near-valence defect densities lead to bimolecular nonradiative recombination which is reduced by 92% after APTMS treatment. Electrochemical characterization of these same active layers shows for the first time that APTMS passivation impacts mainly on near-valence (mobile anionic) defects that decrease in density by 4 orders of magnitude, from 10 18 cm –3 to 10 14 cm –3 , as a result of silane modification. Here, the combination of PL and electrochemical characterization promises a unique approach to speciation and quantification of a broader distribution of trap states in perovskites and provides straightforward assessments of the efficacy of defect mitigation strategies.

Defects↗
NASA NTRS1980

Simultaneous radiation damage and annealing of GaAs solar cells

In this report, concepts and equations are developed to describe the simultaneous radiation damage and annealing of solar cells. The annealing characteristics of three types of defects are employed to study three examples of continuous irradiation and annealing. One example shows that the effective damage could be reduced by a factor of fifty. The difficulty of a laboratory experiment properly simulating the effects in space are discussed. Potential advantages of continuous annealing such as reduction of stable defect formation and omission of radiation cover glasses are presented.

Heinbockel, J. H.↗