SEARCH · Engineering Papers

Results for “slots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1934

The effects of equal-pressure fixed slots on the characteristics of a Clark Y Airfoil

A type of fixed open slot so arranged that no flow would pass through it at a lift coefficient corresponding to high-speed flight was investigated in the N.A.C.A. 7 by 10 foot wind tunnel to determine the possibilities of such a high-lift device for increasing the speed-range ratio of a wing. The condition of no through flow was achieved by locating the slot openings at points of equal static pressure at the design lift coefficient as determined from the pressure distribution about the plain wing. Two models of Clark Y wings with such equal-pressure slots were tested and the smoke-flow patterns about them observed. The results of this investigation show that the condition of no air flow through the slot at the desired lift coefficient is attainable. The surface discontinuities produced by the slot openings have, however, such a large effect on the drag that such slots show little promise. An appreciable increase is produced in the maximum lift and the speed-range can be as high as for the plain wing.

Harris, Thomas A↗

NASA NTRS1939

Tests of an N.A.C.A. 23012 Airfoil with a slotted deflector flap

Section aerodynamic characteristics of a large-chord N.A.C.A. 23012 airfoil with a slotted deflector flap were obtained in the N.A.C.A. 7- by 10-foot wind tunnel. The characteristics of an N.A.C.A. slotted flap and of a simple split flap are included for comparison. The slotted deflector flap was found to have a somewhat lower maximum lift coefficient and somewhat higher drag at high lift coefficients than the N.A.C.A. slotted flap. The high drag of the open slot with the deflector flap neutral indicates that the slot should be closed for this condition.

House, R O↗

NASA NTRS1996

Flowfield Measurements Inside a Boundary-Layer Bleed Slot

An experimental investigation was conducted to determine the flowfield inside a bleed slot used to control an oblique shock-wave and turbulent boundary-layer interaction. The slot was oriented normal to the primary flow direction and had a width of 1.0 cm (primary flow direction) and a length of 2.54 cm and spanned 16.5 cm. The approach boundary layer upstream of the interaction was nominally 3.0 cm thick. Two operating conditions were studied: M = 1.98 with a shock generator deflection angle of 6 deg and M = 2.46 with a shock generator deflection angle of 8 deg. Measurements include surface and flowfield static pressure, pitot pressure, and total mass flow through the slot. The results show that despite an initially two-dimensional interaction for the zero-bleed-flow case, the slot does not remove mass uniformly in the spanwise direction. Inside the slot, the flow is characterized bv two separation regions, which significantly reduce the effective flow area. The upper separation region acts as an aerodynamic throat, resulting in supersonic flow through much of the slot.

Davis, D. O.↗

NASA NTRS1998

Flowfield Measurements in a Slot-Bled Oblique Shock Wave and Turbulent Boundary-Layer Interaction

An experimental investigation was conducted to determine the flowfield inside a bleed slot used to control an oblique shock-wave and turbulent boundary-layer interaction. The slot was oriented normal to the primary flow direction and had a width of 1.0 cm (primary flow direction), a length of 2.54 cm, and spanned 16.5 cm. The approach boundary layer upstream of the interaction was nominally 3.0 cm thick. Two operating conditions were studied: M = 1.98 with a shock generator deflection angle of 6 deg and M= 2.46 with a shock generator deflection angle of 8 deg. Measurements include surface and flowfield static pressure, Pitot pressure, and total mass-flow through the slot. The results show that despite an initially two-dimensional interaction for the zero bleed-flow case, the slot does not remove mass uniformly in the spanwise direction. Inside the slot, the flow is characterized by two separation regions which significantly reduce the effective flow area. The upper separation region acts as an aerodynamic throat resulting in supersonic flow through much of the slot.

Davis, D. O.↗

NASA NTRS1994

Computational Analysis of Forebody Tangential Slot Blowing on the F/A-18

An overview of the computational effort to analyze forebody tangential slot blowing for use on the F/A-18 aircraft is presented. Tangential slot blowing generates side force and yawing moment which may be used to control the aircraft flying at high angle of attack. Computations using the isolated forebody are obtained at full-scale wind tunnel test conditions for direct comparison with available experimental data. The effects of jet exit conditions, jet length, and jet location are also studied using the isolated forebody. In addition, these computations are used to predict the effect of slot blowing at transonic maneuvering flight conditions. The effects of over- and under-blowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side force and yawing moments generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. The effect of blowing on the burst point location are then analyzed by obtaining computations using the aircraft geometry, which includes the wing, empennage, and faired-over inlets. The effect of blowing on the buffet loads on the vertical tails are analyzed using time-accurate computations. Comparison with available experimental data from full-scale wind tunnel and sub-scale wind tunnel tests are made. This computational analysis compliments the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about the F/A-18.

Gee, Ken↗

NASA NTRS1961

Effects of Various Arrangements of Slotted and Round Jet Exits on the Lift and Pitching-Moment Characteristics of a Rectangular-Base Model at Zero Forward Speed

An investigation was made to determine some of the effects of various arrangements of slotted and round jet exits on the lift and pitching-moment characteristics of a rectangular-base model at zero forward speed. Jet-exit slots near the perimeter of the model usually gave larger lift-thrust ratios than slots nearer the center line when the model was near the ground, but away from the ground perimeter jets forming almost a closed jet curtain induced negative pressures on the bottom of the model and resulted in less lift than that obtained with more centrally located jets or jets with large gaps in the jet curtain. Most models with jet slots symmetrical about the pitch axis gave approximately zero pitching moments through the range of ground-board distances, but under some conditions unstable flow direction caused positive or negative pitching moments to occur. With wings attached to the models, the lift close to the ground was 10 to 20 percent less than the lift away from the ground for various configurations. The round jets gave poorer lift-thrust ratios than the slotted jets in the region of ground effect. Out of the region of ground effect the round jets gave the greatest lift-thrust ratio per unit of weight rate of flow of air, for equal jet-exit areas, and the thinnest slotted jet gave the least.

Vogler, Raymond D.↗

NASA NTRS2011

Spreadsheet Calculation of Jets in Crossflow: Opposed Rows of Slots Slanted at 45 Degrees

The purpose of this study was to extend a baseline empirical model to the case of jets entering the mainstream flow from opposed rows of 45 degrees slanted slots. The results in this report were obtained using a spreadsheet modified from the one posted with NASA/TM--2010-216100. The primary conclusion in this report is that the best mixing configuration for opposed rows of 45 degrees slanted slots at any down stream distance is a parallel staggered configuration where the slots are angled in the same direction on top and bottom walls and one side is shifted by half the orifice spacing. Although distributions from perpendicular slanted slots are similar to those from parallel staggered configurations at some downstream locations, results for perpendicular slots are highly dependent on downstream distance and are no better than parallel staggered slots at locations where they are similar and are worse than parallel ones at other distances.

Holderman, James D.↗

NASA NTRS2011

Spreadsheet Calculation of Jets in Crossflow: Opposed Rows of Slots Slanted at 45 Degrees

Holderman, James D.↗

NASA NTRSDate not supplied

Design Exploration of a Transonic Cruise Slotted Airfoil

A knowledge-based aerodynamic design method, CDISC, has been leveraged for the computational design exploration of the cruise slotted airfoil as a drag-saving technology for single aisle, transonic transport aircraft. Aerodynamic predictions were generated using the NASA USM3D Reynolds-averaged Navier-Stokes flow solver, and laminar flow assessments were conducted using the NASA BLSTA3D boundary layer profile solver paired with the LASTRAC stability analysis and transition prediction software. The CDISC design method was used to parametrically vary several slotted-airfoil design variables to understand their impact on aerodynamic performance. In addition to establishing best practices for slotted airfoil design, it was observed that the historically noted skin-friction penalty for cruise slotted airfoils was attributed to the low-Reynolds-number boundary layer of the flap. At cruise, this skin-friction penalty negated any potential decrease in pressure drag enabled by the cruise slotted airfoil architecture. This observation led to the development of an Aft-Laminar Multi-element Airfoil concept that uses airfoil shaping to promote natural laminar flow on the flap. At cruise conditions, the concept is predicted to offer a 2.7% reduction in sectional drag relative to a fully turbulent supercritical airfoil. Off-design analyses showed that laminar flow could be maintained with near-cruise variations in angle of attack and Mach number, resulting in sustained aerodynamic efficiency improvements and a delay in the drag rise Mach number. A low-speed, high-lift analysis at takeoff conditions predicted a maximum lift coefficient of 2.4 could be achieved by use of a variable-camber leading edge on the main element and simple deflection of the flap. These computationally-predicted benefits have motivated future research toward an aft-laminar cruise slotted wing design as an incremental step toward the application of natural laminar flow technology on transonic commercial transports.

Brett R Hiller↗

NASA NTRSDate not supplied

Combined Electromagnetic and Thermal Design Optimization Studies of in-Slot Cooling for UAM Electric Motors

Abstract- Urban Air Mobility vehicles will require high specific power and high reliability electric motors. Motor specific power is limited by the temperature limits of stator windings insulation and the motor cooling system’s ability to extract heat from the motor windings. The temperature limits of the stator winding are set by both thermal-chemical aging and thermo-mechanical stresses. In-slot cooling is known to be able to both more effectively reduce the max hotspot temperature in a winding and the thermo-mechanical stress in a winding at a given hotspot temperature relative to external cooling jackets. In this paper, a combined electromagnetic, thermal, and mechanical optimization of in-slot cooled motors for UAM applications is completed. Initial thermal and mechanical studies of in-slot cooling topologies with a reference design were used to down select an in-slot cooled topology for optimization. Optimizations were carried out for a representative UAM mission profile on both the in-slot cooled topology and a traditional externally cooled motor. Results show that the in-slot cooling topology can achieve a smaller mass than a traditional water jacket cooled design, but at the cost of lower efficiency due larger required stator thicknesses and correspondingly larger stator iron loss.

Thomas Tallerico↗

NASA NTRSDate not supplied

Combined Electromagnetic and Thermal Design Optimization Studies of In-Slot Cooling for UAM Electric Motors

Urban Air Mobility vehicles will require high specific power and high reliability electric motors. Motor specific power is limited by the temperature limits of stator winding insulation and the motor cooling system’s ability to extract heat from the motor windings. The temperature limits of the stator winding are set by both thermal-chemical aging and thermo-mechanical stresses. In-slot cooling is known to be able to both more effectively reduce the max hotspot temperature in a winding and the thermo-mechanical stress in a winding at a given hotspot temperature relative to external cooling jackets. In this paper, a combined electromagnetic, thermal, and mechanical optimization of in-slot cooled motors for UAM applications is completed. Initial thermal and mechanical studies of in-slot cooling topologies with a reference design were used to down select an in-slot cooled topology for optimization. Optimizations were carried out for both the in-slot cooled topology and a traditional externally cooled motor. Results show that the in-slot cooling topology can achieve a smaller mass than a traditional water jacket cooled design, but at the cost of lower efficiency due to larger required stator thicknesses and correspondingly larger stator iron loss.

Thomas Tallerico↗

DOE OSTI2023

Fluid dynamic and thermal performance of a slotted cylinder at low Reynolds number

The fluid dynamic and thermal performance of a circular cylinder with a slot parallel to the flow is numerically investigated. The study utilized the semi-implicit finite volume multi-material algorithm MPM-ICE, a component of the Uintah framework. The normalized slot width s/D ranges from 0.1 - 0.3, introducing an additional heat transfer surface area between ~ 10 and ~ 50%, and a mass reduction between ~ 13 and ~ 38% in the cylinder. We assumed two-dimensional incompressible flow and simulated a Reynolds number Re D between 100 and 1000. The slotted cylinders are found to have a total drag force reduction up to ~ 45%, compared to a solid cylinder despite the additional viscous drag force in the slot. Convection heat transfer is enhanced up to ~ 70%. Further, the slotted cylinder performance index, defined as the ratio of the heat rate to the drag force, increases up to maximum of ~ 3, indicating better overall thermal fluid performance. An entropy analysis showed the best performance index occurs at the highest Re D . Correlations for drag coefficient and Nusselt number are proposed along with an entropy optimization method.

42 ENGINEERING↗

NASA NTRS2002

Application of a Slotted Airfoil for UH-60A Helicopter Performance

Recently developed forward slotted airfoils were applied to a UH-60A helicopter, and the performance has been estimated. Baseline SC1095 and SC1094 R8 airfoil characteristics were modified based on CFD calculations of an A3c slotted airfoil to incorporate aerodynamic characteristics of a high-lifting airfoil. The slotted airfoil increases maximum thrust of the UH-60A helicopter by up to 25%, but a significant penalty is observed at CTI9 less than 0.11. This penalty results from higher drag than the baseline airfoil at low angles of attack. A drag reduction at high Mach numbers is necessary to fully exploit the airfoil capability in the rotorcraft application. Preliminary comparison of the slotted airfoil with the wide chord blade shows that the slotted airfoil has limited advantages over the wide chord blade.

UH-60A AIRCRAFT↗

NASA NTRS1972

Wind tunnel study of slot spoilers for direct lift control

An investigation was conducted in a 300-mph 7- by 10- foot tunnel to obtain data for a slot spoiler direct lift control system. Slot spoilers are believed to have advantages over flap-type direct lift control (DLC) systems because of the small amount of power required for actuation. These tests, run at a Reynolds number of 1,400,000 showed that up to 78 percent of the lift due to flap deflection could be spoiled by opening several spanwise slots within the flaps. For a given lift change the drag change was significantly less than that which would be obtained by a variable flap DLC system. A nozzle-shaped slot was the most effective of the slot shapes tested.

Andrisani, D., II↗

NASA NTRS1969

Evaluation, construction and endurance testing of compression sealed pyrolytic boron nitride slot insulation

A high-temperature statorette, consisting of an iron-27 percent cobalt magnetic lamination stack and nickel-clad silver conductors, was tested with pyrolytic boron nitride slot insulation. Temperatures were measured in each test to determine characteristics of slot linear heat conductance from statorette conductors. Testing was carried out to temperatures of approximately 1500 F in a vacuum environment of 10-8 torr. Three assemblies were built and tested, each having a different room temperature slot clearance. The final statorette assembly was subjected to a 100-hour vacuum aging test at 1400 F followed by 25 thermal cycles. Temperature data from the three assemblies showed that decreasing slot clearance and increasing compression loading did enhance heat transfer. The temperature difference between slot and lamination at 1400 F increased 4 F during the thermal aging and an additional 10 F during the 25 thermal cycles.

Grant, W. L.↗

NASA NTRS1972

Multiple slot laminar film cooling.

An analytical investigation is presented showing the effect of film cooling using single and double slots. The analysis considers the tangential injection of a gas of the same molecular weight as the main flow into a laminar boundary layer. Results in terms of heat transfer to the wall are presented for different slot heights, and injection velocities for both single and double slot configurations. The results indicate that the double slot is a more effective means of film cooling than the single slot.

Sherman, A.↗

NASA NTRS1973

Full-scale wind-tunnel investigation of effects of slot spoilers on the aerodynamic characteristics of a light twin-engine airplane

A wind-tunnel investigation has been conducted to determine the effects of slot spoilers on the longitudinal and lateral aerodynamic characteristics of a full-scale mockup of a light twin-engine airplane. The slots were located along the leading edge of the flaps and were used to modulate the flap-induced lift as a possible means of achieving direct lift control. The data showed that the slots were effective in spoiling up to 61 percent of the flap-induced lift, but that an adverse pitching-moment change (nose up) accompanied opening the slots. Opening the slots was found to decrease slightly the downwash angle at the tail and to increase slightly the longitudinal stability of the model.

Verstynen, H. A., Jr.↗

NASA NTRS1973

Acoustic testing of a supersonic tip speed fan with acoustic treatment and rotor casting slots. Quiet engine program scale model fan C

Acoustic tests were conducted on a high tip speed (1550 ft/sec, 472.44 m/sec) single stage fan with varying amounts of wall acoustic treatment and with circumferential slots over the rotor blade tips. The slots were also tested with acoustic treatment placed behind the slots. The wall treatment results show that the inlet treatment is more effective at high fan speeds and aft duct treatment is more effective at low fan speeds. Maximum PNL's on a 200-foot (60.96 m) sideline show the untreated slots to have increased the rear radiated noise at approach. However, when the treatment was added to the slots inlet radiated noise was decreased, resulting in little change relative to the solid casing on an EPNL basis.

Kazin, S. B.↗