Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “room temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Mitigating Heavy Ion Irradiation‐Induced Degradation in p‐type SnO Thin‐Film Transistors at Room Temperature

The study investigates the mitigation of radiation damage on p‐type SnO thin‐film transistors (TFTs) with a fast, room‐temperature annealing process. Atomic layer deposition is utilized to fabricate bottom‐gate TFTs of high‐quality p‐type SnO layers. After 2.8 MeV Au 4+ irradiation at a fluence level of 5.2 × 10 12 ions cm −2 , the output drain current and on/off current ratio ( I on / I off ) decrease by more than one order of magnitude, field‐effect mobility ( μ FE ) reduces more than four times, and subthreshold swing (SS) increases more than four times along with a negative shift in threshold voltage. The observed degradation is attributed to increased surface roughness and defect density, as confirmed by scanning electron microscopy (SEM), high‐resolution micro‐Raman, and transmission electron microscopy (TEM) with geometric phase analysis (GPA). A technique is demonstrated to recover the device performance at room temperature and in less than a minute, using the electron wind force (EWF) obtained from low‐duty‐cycle high‐density pulsed current. At a pulsed current density of 4.0 × 10 5 A cm −2 , approximately four times increase in I on / I off is observed, 41% increase in μ FE , and 20% decrease in the SS of the irradiated TFTs, suggesting effectiveness of the new annealing technique.

Al-Mamun, Nahid Sultan↗
DOE OSTI2021

Growth of Cd 0.9 Zn 0.1 Te 1-y Se y Single Crystals for Room Temperature Gamma-Ray Detection

Quaternary Cd 0.9 Zn 0.1 Te 1-y Sey (CZTS) single crystals, a novel room-temperature nuclear radiation detector semiconductor material, have been grown using a modified vertical Bridgman method (VBM) and a travelling heater method (THM). The percentage concentration of selenium in the VBM-grown crystal was 3% and that in the THM-grown crystal was 2%. While the THM Frisch collar detector (4.4 × 4.4 × 10.7 mm 3 ) produced a highly resolved pulse height spectra (PHS) with a resolution of ~1.06% for 662-keV gamma rays without any correction, the VBM-grown detector (10 × 10 × 2 mm 3 ) offered a high energy resolution of ~2% after application of a digital biparametric correction. The high-resolution performance of these detectors has been attributed to the addition of Se in the Cd 0.9 Zn 0.1 Te (CZT) matrix. Ab-initio calculations based on density functional theory (DFT) also confirmed that the addition of Se in the CZT matrix helps to reduce the formation of TeCd and the TeZn anti-sites. The VBM-grown crystals were characterized using powder x-ray diffraction (XRD) and energy dispersive x-ray spectroscopy (EDS). While XRD results revealed sharp diffraction peaks confirming the crystalline nature of the grown crystal, the EDS results confirmed the targeted stoichiometry of the elemental composition. The bulk resistivity of the grown crystal was calculated to be ~3 × 10 10 Ω-cm from current-voltage characteristics recorded at room temperature in a planar configuration, ensuring that the grown CZTS crystals have low dark current as required for detector-grade crystals.

42 ENGINEERING↗
DOE OSTI2025

Solution-Processed Ultrafast, Room-Temperature Single-Photon Source at 1550 nm

Single photons are cornerstones of quantum technologies. The need for an ultrafast, bright, and stable photon source emitting in the telecom-band at ∼1550 nm, ideally operating at room temperature, has resulted in a decades-long quest. However, to date, telecom sources are hampered by inherently long radiative lifetimes that severely limit brightness and speed, material instability, or the need for cryogenic operation. Here, in this study, stable colloidal PbS/CdS quantum dots emitting at 1550 nm (C-band) or 1350 nm (O-band) are embedded in a solution-synthesized nanoparticle-on-mirror cavity. Single cavity-coupled quantum dots experience extreme Purcell factors up to 10,700, resulting in ultrafast emission lifetimes of 65 ps, along with near-complete blinking suppression. As a result, 12 million single photons are emitted per second affording a single photon source at 1550 nm that is more than two orders of magnitude brighter than previously possible at room-temperature. These telecom-band single photon sources are solution-processable and lithography-free and may leverage mature colloidal fabrication technologies for future quantum applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Low-temperature liquid-phase synthesis of lithium thiophosphate-borohydride solid electrolyte with high room-temperature ionic conductivity

Embodiments relate to a scalable liquid-phase synthesis technique of lithium thiophosphate-borohydride solid electrolytes with high ionic conductivity at room temperature and its use in all-solid-state lithium batteries. A battery comprises an anode, a cathode, and a solid electrolyte layer positioned between the anode and the cathode. The liquid-phase synthesized solid electrolyte material can be used as the solid electrolyte layer or incorporated into anodes or cathodes.

Wang, Donghai [Pennsylvania State Univ., Universit↗
DOE OSTI2020

Diffusivity and Structure of Room Temperature Ionic Liquid in Various Organic Solvents

Room-temperature ionic liquids (RTILs) hold promise for applications in electric double layer capacitors (EDLCs), owing to a much wider potential window, lower vapor pressure, and better thermal and chemical stabilities compared to conventional aqueous and organic electrolytes. However, because the low diffusivity of ions in neat RTILs negates the EDLCs’ advantage of high power density, the ionic liquids are often used in mixture with organic solvents. In this study, we measured the diffusivity of cations and anions in RTIL, 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) ([BMIM + ][TFSI – ]), mixed with 10 organic solvents, by using the pulsed-field gradient NMR method. The ion diffusivity was found to follow that of neat solvents and in most studied solvents showed an excellent agreement with the predicted values reported in the recent molecular dynamics (MD) study [Thompson, M. W.; J. Phys. Chem. B 2019, 123, 1340-1347]. In two solvents consisting of long-chain molecules, however, the MD simulations predictions slightly underestimated the ionic diffusivities. The degree of ion dissociation was also estimated for each solvent by comparing the ionic conductivity with the molar conductivity derived from the diffusion measurements. The degree of ion dissociation and the hydrodynamic radius of ions suggest that the ions are coordinated by ~1 solvent molecule. Finally, the scarcity of solvent–ion interactions explains the fact that the diffusivity of ions in the mixture significantly depends on the viscosity of the solvent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A capillary-based microfluidic device enables primary high-throughput room-temperature crystallographic screening

A novel capillary-based microfluidic strategy to accelerate the process of small-molecule-compound screening by room-temperature X-ray crystallography using protein crystals is reported. The ultra-thin microfluidic devices are composed of a UV-curable polymer, patterned by cleanroom photolithography, and have nine capillary channels per chip. The chip was designed for ease of sample manipulation, sample stability and minimal X-ray background. 3D-printed frames and cassettes conforming to SBS standards are used to house the capillary chips, providing additional mechanical stability and compatibility with automated liquid- and sample-handling robotics. These devices enable an innovative in situ crystal-soaking screening workflow, akin to high-throughput compound screening, such that quantitative electron density maps sufficient to determine weak binding events are efficiently obtained. This work paves the way for adopting a room-temperature microfluidics-based sample delivery method at synchrotron sources to facilitate high-throughput protein-crystallography-based screening of compounds at high concentration with the aim of discovering novel binding events in an automated manner.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Spin-Glass-like State and Reversible Room-Temperature Magnetocaloric Effect in Double Distorted Perovskites Nd(Cu 3– x Mn x )Mn 4 O 12

The preparation, complex magnetic properties and room-temperature magnetocaloric effect in Nd(Cu 3–x Mn x )Mn 4 O 12 with cation distribution (Nd 3+ ) A (Cu 3–x 2+x Mn x 3+ ) A' (Mn 1+x 3+ Mn 3–x 4+ ) B O 12 2– (x = 1 and 1.5) have been reported. Both compounds show a sharp paramagnetic-ferromagnetic (FM) transition at T C of 300 and 280 K, respectively. The substitution of Cu by Mn at the A' site induces the emergence of a spin glass state below ≈63 K for x = 1 and ≈72 K for x = 1.5 compound. Another antiferromagnetic-like magnetic transition is also observed in both compounds at 23 and 28 K, respectively, which is discussed as the antiferromagnetic coupling between Nd 3+ at the A' site and (Mn 3+ /Mn 4+ ) at the B site. These two compounds exhibit room-temperature magnetocaloric effect. For a small field of 2 T, the maximum magnetic entropy changes –ΔS M are 1.5 J/kg K at 300 K and 1.4 J/kg K at 280 K, respectively. Furthermore, the –ΔS M (T) curves show an asymmetric distribution, resulting in high refrigerant capacity values for both compounds. We further demonstrate the distinct roles of the A'- and B-site spins on the magnetic properties and the origin of the spin-glass-like state in double distorted perovskites Ln(Cu 3–x Mn x )Mn 4 O 12 family of compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Room‐Temperature Mid‐Infrared Detection Using Metasurface‐Absorber‐Integrated Phononic Crystal Oscillator

Mid-infrared (MIR) detectors find extensive applications in chemical sensing, spectroscopy, communications, biomedical diagnosis, and space exploration. Alternative to semiconductor MIR photodiodes and bolometers, mechanical-resonator-based MIR detectors show advantages in higher sensitivity and lower noise at room temperature, especially toward longer wavelength infrared. Here, uncooled room-temperature MIR detectors based on lithium niobate surface acoustic wave phononic crystal (PnC) resonators integrated with wavelength-and-polarization-selective metasurface absorber arrays are demonstrated. The detection is based on the resonant frequency shift induced by the local temperature change due to MIR absorptions. The PnC resonator is configured in an oscillating mode, enabling active readout and low-frequency noise. The 1-GHz oscillator-based MIR detector shows a relative frequency deviation of 5.24 × 10 −10 Hz −1/2 at an integration time of 50 µs, leading to an incident noise equivalent power of 197 pW Hz −1/2 when input 6-µm MIR light is modulated at 1.8 kHz, and a large dynamic range of 10 7 in incident MIR power. The device architecture is compatible with the scalable manufacturing process and can be readily extended to a broader spectral range by tailoring the absorbing wavelengths of metasurface absorbers.

Xi, Zichen [Virginia Polytechnic Inst. and State U↗
DOE OSTI2025

Heterogenous Integration of Boron-Doped p -Diamond with Monolayer n -MoS 2 for PN Junctions Operating at Room Temperature

Diamond has tremendous potential for power electronics, due to its superior thermal conductivity, large electric field strength, and high carrier mobilities. However, the absence of a reliable room temperature n-type transport has impeded any advancements in diamond-based electronics. Here, we circumvent this bottleneck by integrating n-type two-dimensional (2D) monolayers of molybdenum disulfide (MoS 2 ) with boron doped p-type single crystal diamond and demonstrate 2D/3D heterostructure-based PN junction diodes that operate at room temperature with excellent rectification characteristics. Our diodes achieve a maximum forward current density (J D ) of ∼4000 A/cm 2 , an ideality factor (η) value of ∼3.7, and a rectification ratio (RR) of 10 6 . We find that the origin of current rectification stems from the interlayer recombination of majority carriers driven by direct tunnelling (DT) and Fowler Nordheim (FN) tunnelling mechanisms. In conclusion, our demonstration can open new avenues for diamond-based power electronics through its integration with 2D materials.

2D/3D integration↗
DOE OSTI2023

Revealing protonation states and tracking substrate in serine hydroxymethyltransferase with room-temperature X-ray and neutron crystallography

Pyridoxal 5’-phosphate (PLP)-dependent enzymes utilize a vitamin B 6 -derived cofactor to perform a myriad of chemical transformations on amino acids and other small molecules. Some PLP-dependent enzymes, such as serine hydroxymethyltransferase (SHMT), are promising drug targets for the design of small-molecule antimicrobials and anticancer therapeutics, while others have been used to synthesize pharmaceutical building blocks. Understanding PLP-dependent catalysis and the reaction specificity is crucial to advance structure-assisted drug design and enzyme engineering. Here we report the direct determination of the protonation states in the active site of Thermus thermophilus SHMT (TthSHMT) in the internal aldimine state using room-temperature joint X-ray/neutron crystallography. Conserved active site architecture of the model enzyme TthSHMT and of human mitochondrial SHMT (hSHMT2) were compared by obtaining a room-temperature X-ray structure of hSHMT2, suggesting identical protonation states in the human enzyme. The amino acid substrate serine pathway through the TthSHMT active site cavity was tracked, revealing the peripheral and cationic binding sites that correspond to the pre-Michaelis and pseudo-Michaelis complexes, respectively. At the peripheral binding site, the substrate is bound in the zwitterionic form. By analyzing the observed protonation states, Glu53, but not His residues, is proposed as the general base catalyst, orchestrating the retro-aldol transformation of L-serine into glycine.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Room temperature sodium diffusion in sodium iron phosphate investigated with neutron scattering

Sodium iron phosphate, Na x FePO 4 , is currently one of the most promising cathode materials for sodium ion batteries. Here we employ a systematic approach using three neutron scattering techniques to investigate temperature dependent properties with a focus on the charge transfer processes. Two distinct Na + diffusive motions are observed with quasielastic neutron scattering, including room temperature motion. These processes correspond to rapid double jumps through extrinsic vacancy sites of ∼6 Å along with the more fundamental nearest neighbor jumps of 3.1 Å. Experimental observations of room temperature ionic diffusion are highly desirable, as the diffusion pathways are naturally well suited for efficient transport. Inelastic neutron scattering was used to probe the vibrational density of states that assist in the ionic and electronic (polaronic) transport processes, which are further supported with density functional theory. Neutron diffraction examines the disordering of the sodium sublattice upon transition to the solid-solution phase, which is believed to enhance the overall kinetics during sodium insertion/extraction. Finally, 57 Fe Mössbauer spectroscopy measurements probes polaron hopping and the local structural evolution that modifies the electron density surrounding the redox active iron sites. This study sheds light on the temperature induced atomic scale dynamics that occur in olivine Na x FePO 4 .

Novak, Eric [Swarthmore College, Swarthmore, PA (U↗
DOE OSTI2025

Low-loss superconducting resonators fabricated from tantalum films grown at room temperature

The use of α-tantalum in superconducting circuits has enabled a considerable improvement in the coherence time of transmon qubits. The standard approach to grow α-tantalum thin films on silicon involves heating the substrate, which takes several hours per deposition and prevents the integration of this material with wafers containing temperature-sensitive components. We report a detailed experimental study of an alternative growth method of α-tantalum on silicon, which is achieved at room temperature through the use of a niobium seed layer. Despite a substantially higher density of oxygen-rich grain boundaries in the films sputtered at room temperature, resonators made from these films are found to have state-of-the-art quality factors, comparable to resonators fabricated from tantalum grown at high temperature. This finding challenges previous assumptions about correlations between material properties and microwave loss of superconducting thin films, and opens a new avenue for the integration of tantalum into fabrication flows with limited thermal budget.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Understanding the reversible electrodeposition of aluminum in low-cost room-temperature molten salts

Aluminum is the most earth-abundant metal, trivalent, and inert in ambient air; it also has a density approximately five times that of lithium at room temperature, making it attractive for cost-effective, long-duration storage in batteries. Here, we investigate structural requirements and physicochemical and transport properties of ionic liquid (IL) electrolytes thought to enable high reversibility of Al battery anodes. We find that intentionally designed, low-cost IL analogs, including ammonium-based molten salts, offer comparable Al anode reversibility to state-of-the-art imidazolium-based IL melts. A critical ratio of solvated Al-ion species is required to balance the effects of Lewis acidity needed to continuously etch native Al 2 O 3 and form a stable solid electrolyte interphase on Al. Our findings open new opportunities for developing simple, cost-effective, room-temperature Al batteries that enable long-duration electrical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2023

Room-Temperature Eutectic Synthesis for Upcycling of Cathode Materials

Ni-rich LiNixMnyCo1−x−yO2 (NMC) materials have been adopted in a range of applications, including electric vehicles. The recycled NMC material from a spent cell would be much more valuable if it could be upgraded to a Ni-rich, more energy-dense version of the material. This work demonstrates a simple, inexpensive, and facile method to upcycle LiNi1/3Mn1/3Co1/3O2 (NMC111, 160 mAh∙g−1), a cathode used in early generations of electric vehicle batteries, to LiNi0.8Mn0.1Co0.1O2 (NMC811, 190 mAh∙g−1), a more energy-dense cathode material. In this study, a preliminary investigation into a room-temperature eutectic synthesis of NMC811 is performed using NMC111, LiOH, and nickel nitrate as precursors. The synthesized material showed the desired crystal structure and stoichiometry, though the cycle life and Li diffusion coefficient need improvement when compared to commercially available NMC811. This study demonstrates an interesting proof of concept of the room-temperature eutectic synthesis process for LIB cathodes and could be improved by tuning the synthesis conditions.

lithium-ion battery↗
DOE OSTI2022

Coupling Two Laser-Cooled Ions via a Room-Temperature Conductor

We demonstrate coupling between the motions of two independently trapped ions with a separation distance of 620 μm. Here, the ion-ion interaction is enhanced via a room-temperature electrically floating metallic wire which connects two surface traps. Tuning the motion of both ions into resonance, we show flow of energy with a coupling rate of 11 Hz. Quantum-coherent coupling is hindered by strong surface electric-field noise in our device. Our ion-wire-ion system demonstrates that room-temperature conductors can be used to mediate and tune interactions between independently trapped charges over distances beyond those achievable with free-space dipole-dipole coupling. This technology may be used to sympathetically cool or entangle remotely trapped charges and enable coupling between disparate physical systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Unconventional room-temperature carriers in the triangular-lattice Mott insulator TbInO3

Abstract The strong correlations between electrons in Mott insulator materials may produce highly entangled many-body states with unconventional emergent excitations. The signatures of such excitations, if any, are commonly believed to be observable only at low temperatures. Here, we challenge this common belief and show using terahertz time-domain spectroscopy that exotic carriers exist even at room temperature in TbInO 3 , a candidate material for realizing a low-temperature quantum spin-liquid phase. In particular, over the entire temperature range of 1.5–300 K, we observe a quadratic frequency dependence in the real part of the in-plane optical conductivity as well as Fano asymmetry of an optical phonon mode strongly interacting with the excitation continuum. These features are robust even under external magnetic fields of up to 7 T. Our data confirm the presence of emergent charge carriers within the Mott charge gap of TbInO 3 , suggesting that it is possible to probe and manipulate highly entangled quantum many-body states at room temperature.

Physics↗