Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reading error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Experimental techniques for evaluating steady-state jet engine performance in an altitude facility

Jet engine calibration tests were conducted in an altitude facility using a contoured bellmouth inlet duct, four fixed-area water-cooled exhaust nozzles, and an accurately calibrated thrust measuring system. Accurate determination of the airflow measuring station flow coefficient, the flow and thrust coefficients of the exhaust nozzles, and the experimental and theoretical terms in the nozzle gross thrust equation were some of the objectives of the tests. A primary objective was to develop a technique to determine gross thrust for the turbojet engine used in this test that could also be used for future engine and nozzle evaluation tests. The probable error in airflow measurement was found to be approximately 0.6 percent at the bellmouth throat design Mach number of 0.6. The probable error in nozzle gross thrust measurement was approximated 0.6 percent at the load cell full-scale reading.

Smith, J. M.↗
NASA NTRS1972

Effect of operating conditions on the exhaust emissions from a gas turbine combustor

Exhaust concentrations of total unburned hydrocarbons, carbon monoxide, and nitric oxide were measured from a single J-57 combustor liner installed in a 30 diameter test section. Tests were conducted over a range of inlet total pressures from 1 to 20 atmospheres, inlet total temperatures from 310 to 590 K, reference velocities from 8 to m/sec, and fuel-air ratios from 0.004 to 0.015. Most of the data were obtained using ASTM A-1 fuel; however, a limited number of tests was performed with natural gas fuel. Combustion efficiency and emission levels are correlated with operating conditions. Sampling error at operating conditions for which combustion efficiency was below about 90 percent resulted in abnormally low readings for hydrocarbon emissions.

Briehl, D.↗
NASA NTRS1961

The Smoke-Trail Method for Obtaining Detailed Measurements of the Vertical Wind Profile for Application to Missile-Dynamic-Response Problems

Detailed measurements of the vertical profile of the wind are urgently needed f o r studies of the response of rising missiles, but conventional wind-measuring systems cannot provide the accuracy and detail required over the necessary range of altitudes. A method is presented for obtaining a detailed, accurate profile over a large altitude range. The method utilizes photogrammetric measurement of successive positions of the t rail of an ascending rocket. Construction of a rocketborne smoke generator is discussed and the photography, film reading, and data-reduction procedures are described. The accuracy of the method i s examined and error equations are derived. Finally, some examples of wind profiles measured by this method are shown, and their implications for missile response are indicated.

Henry, Robert M.↗
NASA NTRS2019

GOES-17 Magnetometer On-Orbit Calibration Design and Results

The Geostationary Operational Environmental Satellite-R (GOES-R) is a series of four NOAA weather satellites. Each spacecraft flies a Magnetometer instrument which includes two boom mounted fluxgate sensors located 6.3 and 8.5 meters from the spacecraft. Sensor readings are corrupted by both internal (bias and scale factor) and external (spacecraft emitted fields and misalignments) error sources. In order to estimate the bias, an on-orbit calibration is performed, slewing the spacecraft about multiple axes and then performing a fit of the data to determine zero offset and misalignment terms. The first satellite in the series, GOES-16 was launched in November 2016. Its magnetometer calibration maneuver was found to be inadequate providing insufficient rotation about orthogonal axes. The uncertainty in the estimated biases was found to be in the 3-5 nanotesla range, exceeding the magnetometer accuracy requirement of 1.0 nanotesla. Based on lessons learned, the maneuver was redesigned to provide multiple 360 degree rotations about two orthogonal axes, providing optimal visibility into bias and misalignment. Varying ambient fields over the duration of the calibration maneuvers, corrupts the ability to accurately determine parameters of interest. To address this issue, rather than assuming a constant field for the duration of the maneuver, a non-linear least squares filter was employed that uses a series of spline functions to better fit the ambient field. The number of splines can be varied to minimize the least squares filter residuals. Simulations were performed using 360 days of GOES-16 data to bound the uncertainty in the biases for given residuals of the fit to the ambient field. Following the launch of the second satellite in the series, GOES-17 in March 2018, the new calibration maneuver and enhanced bias estimation algorithm were exercised twice. Based on the residuals of the fit, the uncertainty of the estimated zero offset was reduced by an order of magnitude from 3-5 nanotesla to approximately 0.4 nanotesla per axis. This paper provides details of the maneuver design and the innovative algorithm used to estimate the GOES-17 biases and misalignments.

GOES-17↗
NASA NTRSDate not supplied

Estimation With Range Depended Sensor Model

This paper focuses on the improvement of object detection accuracy taking into account the sensor’s reading degradation as the relative range increases. The approach is based on the assumption that range measurement error depends on the actual range. Specifically, we model the measurement error as a proportional to the actual range term plus a zero-mean, Gaussian distributed, and uncorrelated process. The tracking problem is considered in a mixed continuous-discrete time domain, where the target dynamics is in continuous-time and the measurements are in discrete-time, which is an optimal choice in many tracking and navigation applications. We adopt a commonly used continuous time coordinate-uncoupled white-noise acceleration model for a point object to describe the target motion, and use Extended Kalman Filter (EKF) framework to estimate the target's state and the unknown proportionality coefficient.

Vahram Stepanyan↗
NASA NTRSDate not supplied

Estimation With Range Dependent Sensor Model

This paper focuses on the improvement of target tracking accuracy taking into account the sensor’s reading degradation as the relative range increases. The approach is based on the assumption that range measurement error depends on the actual range. Specifically, we model the measurement error as a proportional to the actual range term plus a zero-mean, Gaussian distributed, and uncorrelated process. We present two approaches to tracking a target with constant velocity model. The first approach uses Extended Kalman Filter (EKF) framework to estimate target's states and the unknown proportionality coefficient with linearization on the observation model on the predicted states at each time step. The second one uses a measurement conversion method to estimate the target's scaled by the unknown constant term states, which is shown to be unbiased. This conversion results in linear state and observation models, hence the standard Kalman filter can be applied. The actual target state is computed by application of back scaling with the estimate of unknown scale factor. We evaluate the approaches in desktop simulations.

Target tracking↗
NASA NTRS2009

Guaranteeing Failsafe Operation of Extended-Scene Shack-Hartmann Wavefront Sensor Algorithm

A Shack-Hartmann sensor (SHS) is an optical instrument consisting of a lenslet array and a camera. It is widely used for wavefront sensing in optical testing and astronomical adaptive optics. The camera is placed at the focal point of the lenslet array and points at a star or any other point source. The image captured is an array of spot images. When the wavefront error at the lenslet array changes, the position of each spot measurably shifts from its original position. Determining the shifts of the spot images from their reference points shows the extent of the wavefront error. An adaptive cross-correlation (ACC) algorithm has been developed to use scenes as well as point sources for wavefront error detection. Qualifying an extended scene image is often not an easy task due to changing conditions in scene content, illumination level, background, Poisson noise, read-out noise, dark current, sampling format, and field of view. The proposed new technique based on ACC algorithm analyzes the effects of these conditions on the performance of the ACC algorithm and determines the viability of an extended scene image. If it is viable, then it can be used for error correction; if it is not, the image fails and will not be further processed. By potentially testing for a wide variety of conditions, the algorithm s accuracy can be virtually guaranteed. In a typical application, the ACC algorithm finds image shifts of more than 500 Shack-Hartmann camera sub-images relative to a reference sub -image or cell when performing one wavefront sensing iteration. In the proposed new technique, a pair of test and reference cells is selected from the same frame, preferably from two well-separated locations. The test cell is shifted by an integer number of pixels, say, for example, from m= -5 to 5 along the x-direction by choosing a different area on the same sub-image, and the shifts are estimated using the ACC algorithm. The same is done in the y-direction. If the resulting shift estimate errors are less than a pre-determined threshold (e.g., 0.03 pixel), the image is accepted. Otherwise, it is rejected.

Sidick, Erikin↗
NASA NTRS2009

Effects of Transverse Seat Vibration on Near-Viewing Readability of Alphanumeric Symbology

We measured the impacts on human visual function of a range of vibration levels (0.15, 0.3, 0.5, and 0.7 g) at the frequency and along the axis of the anticipated Ares thrust oscillation. We found statistically significant and equivalent decrements in performance on a reading and a numeric processing task at tested vibration levels above 0.3 g (0-to-peak), but no evidence of after-effects. At the smallest font and highest vibration level tested, the average effect was a 50 percent increase in response time and six-fold increase in errors. Our findings support a preliminary trade space in which currently planned Orion font sizes and text spacing appear to be too small to support accurate and efficient reading at the tested vibration levels above 0.3 g, but not too small to support reading at 0.3 g. This study does not address potential impacts on crew cognitive decision-making or motor control and does not test either the full induced Orion-Ares environment with its sustained Gx-loading or the full complexity of the final Orion seat-helmet-suit interface. A final determination of the Orion-Ares program limit on vibration must take these additional factors into consideration and, thus, may need to be lower than that needed to support effective reading at 1-Gx bias.

Readability↗
NASA NTRS1990

Flight motor set 360L007 (STS-33R)

Flight motor set 360L007 was launched as part of NASA space shuttle mission STS-33R. As with all previous redesigned solid rocket motor launches, overall motor performance was excellent. There were no debris concerns for either motor. Both motors exhibited unbonds on one factory joint weatherseal. All ballistics contract end item specification parameters were verified, with the exception of ignition interval and rise rates. Ignition interval and rise rates could not be verified due to the elimination of developmental flight instrumentation from fourth flight and subsequent, but the low sample rate data that were available showed nominal propulsion performance. All ballistic and mass property parameters closely matched the predicted values and were well within the required contract end item specification levels that could be assessed. All 108 Ground Environment Instrumentation (GEI) measurements performed properly throughout the prelaunch phase. Evaluation of the GEI measurements again verified thermal model analysis data and showed agreement with predicted environmental effects. No launch commit criteria thermal violations occurred. All joint heaters operated normally, but a high voltage reading was noted on the left hand aft heater, which was immediately determined to be a voltage sensor error and not a heater anomaly due to no current increase. Postflight inspection again verified superior performance of the insulation, phenolics, metal parts, and seals. Postflight evaluation indicated both nozzles performed as expected during flight. All combustion gas was contained by insulation in the field and case-to-nozzle joints.

Garecht, Diane↗
NASA NTRS2011

The Western Aeronautical Test Range. Chapter 10 Tools

The Western Aeronautical Test Range (WATR) staff at the NASA Dryden Flight Research Center is developing a translation software called Chapter 10 Tools in response to challenges posed by post-flight processing data files originating from various on-board digital recorders that follow the Range Commanders Council Inter-Range Instrumentation Group (IRIG) 106 Chapter 10 Digital Recording Standard but use differing interpretations of the Standard. The software will read the date files regardless of the vendor implementation of the source recorder, displaying data, identifying and correcting errors, and producing a data file that can be successfully processed post-flight

Knudtson, Kevin↗
NASA NTRS2006

Clustering and Recurring Anomaly Identification: Recurring Anomaly Detection System (ReADS)

This viewgraph presentation reviews the Recurring Anomaly Detection System (ReADS). The Recurring Anomaly Detection System is a tool to analyze text reports, such as aviation reports and maintenance records: (1) Text clustering algorithms group large quantities of reports and documents; Reduces human error and fatigue (2) Identifies interconnected reports; Automates the discovery of possible recurring anomalies; (3) Provides a visualization of the clusters and recurring anomalies We have illustrated our techniques on data from Shuttle and ISS discrepancy reports, as well as ASRS data. ReADS has been integrated with a secure online search

McIntosh, Dawn↗
NASA NTRSDate not supplied

NOR Flash Memory Scrubbing Application for Boot File Preservation of NASA’s Descent and Landing Computer (DLC)

Progress on NASA’s Safe and Precise Landing Integrated Capabilities Evolution (SPLICE)project continues, specifically with this development of the Descent and Landing Computer(DLC). One of the DLC’s primary contributions as a SPLICE technology is its implementationof algorithms and operation of sensors to autonomously guide a spacecraft in performing moreprecise and safer landings on celestial bodies such as the Moon and Mars. The second iterationof the DLC is known as the Engineering Test Unit (ETU) and one of its desired functionalitiesis the ability to preserve the fidelity of the system’s boot file through the use of memoryscrubbing. The ETU has two primary boards, one for housing a Multi-Processor System ona Chip (MPSoC) and the other for housing a Xilinx Kintex Ultrascale FPGA3. To emulate amemory scrubbing function implemented on the ETU’s FPGA board, the design and testingof a software application was performed on a Xilinx KCU105 FPGA evaluation board. Thememory scrubbing application had to meet certain key criteria such as (1) properly utilize withthe flash memory’s Serial Peripheral Interface (SPI) to read, write, and erase flash memoryproperly, (2) be able to detect arbitrarily large or small amounts of bit-errors, (3) be able tocorrect all detected errors, and (4) perform memory scrubbing indefinitely and autonomously.A prototype implementation was constructed and tested, demonstrating successful detectionand correction of bit errors in multiple configurations. In the form of burst errors or singularbit flips, and in amounts of errors ranging from one to fifteen (per 256 Bytes), the applicationwas successful in preserving memory fidelity.

Radiation tolerant↗
NASA NTRSDate not supplied

NOR Flash Memory Scrubbing Application for Boot File Preservation of NASA’s Descent and Landing Computer (DLC)

Progress on NASA’s Safe and Precise Landing Integrated Capabilities Evolution (SPLICE) project continues, specifically with this development of the Descent and Landing Computer (DLC). One of the DLC’s primary contributions as a SPLICE technology is its implementation of algorithms and operation of sensors to autonomously guide a spacecraft in performing more precise and safer landings on celestial bodies such as the Moon and Mars [1]. The second iteration of the DLC is known as the Engineering Test Unit (ETU) and one of its desired functionalities is the ability to preserve the fidelity of the system’s boot file through the use of memory scrubbing [2]. The ETU has two primary boards, one for housing a Multi-Processor System on a Chip (MPSoC) and the other for housing a Xilinx Kintex Ultrascale FPGA*. To emulate a memory scrubbing function implemented on the ETU’s FPGA board, the design and testing of a software application was performed on a Xilinx KCU105 FPGA evaluation board. The memory scrubbing application had to meet certain key criteria such as (1) properly utilize with the flash memory’s Serial Peripheral Interface (SPI) to read, write, and erase flash memory properly, (2) be able to detect arbitrarily large or small amounts of bit-errors, (3) be able to correct all detected errors, and (4) perform memory scrubbing indefinitely and autonomously. A prototype implementation was constructed and tested, demonstrating successful detection and correction of bit errors in multiple configurations. In the form of burst errors or singular bit flips, and in amounts of errors ranging from one to fifteen (per 256 Bytes), the application was successful in preserving memory fidelity.

Flash memory↗
NASA NTRS1986

New short-time alignment technique for 70-meter antenna surface panels

With severely limited field modification time for upgrading the 64-m antenna to 70-m diameter, a new shorter time method for aligning the surface panels of the main reflector was needed. For each target on the surface panel, both distance (or range) and elevation angle measurements are made. A new technique for setting the surface panels at zenith look has been devised. This article describes the software required to convert the computed target distortions obtained from the JPL-IDEAS structural analysis computer program (defining the gravity load change from a 45-deg elevation angle to zenith look) into the theodolite reading at zenith look. The technique results in a perfectly shaped reflector at the 45-deg rigging elevation, with acceptable surface error tolerance.

Katow, M. S.↗
NASA NTRS1988

Engine-Monitoring Algorithm

Allowances made for erroneous sensor readings. Algorithm developed to increase reliability of digital electronic control systems for aircraft turbine engines. Detects, isolates, and accommodates failures or errors in engine sensors. Generates engine-output estimates based on measurements of inputs and outputs and detects failures of input- and output-measuring sensors.

Merrill, Walter C.↗
NASA NTRS1986

Optical Scanner for Linear Arrays

Optical scanner instantaneously reads contiguous lines forming scene or target in object plane. Reading active or passive and scans, continuous or discrete. Scans essentially linear with scan angle and symmetric about axial ray. Nominal focal error, resulting from curvature of scan, well within Rayleigh limit. Scanner specifically designed to be fully compatible with general requirements of linear arrays.

Finkel, M. W.↗
NASA NTRS2004

Implicit and Explicit Spacecraft Gyro Calibration

This paper presents a comparison between two approaches to sensor calibration. According to one approach, called explicit, an estimator compares the sensor readings to reference readings, and uses the difference between the two to estimate the calibration parameters. According to the other approach, called implicit, the sensor error is integrated to form a different entity, which is then compared with a reference quantity of this entity, and the calibration parameters are inferred from the difference. In particular this paper presents the comparison between these approaches when applied to in-flight spacecraft gyro calibration. Reference spacecraft rate is needed for gyro calibration when using the explicit approach; however, such reference rates are not readily available for in-flight calibration. Therefore the calibration parameter-estimator is expanded to include the estimation of that reference rate, which is based on attitude measurements in the form of attitude-quaternion. A comparison between the two approaches is made using simulated data. It is concluded that the performances of the two approaches are basically comparable. Sensitivity tests indicate that the explicit filter results are essentially insensitive to variations in given spacecraft dynamics model parameters.

Bar-Itzhack, Itzhack Y.↗
NASA NTRS2015

Technology Development for the Advanced Technology Large Aperture Space Telescope (ATLAST) as a Candidate Large UV-Optical-Infrared (LUVOIR) Surveyor

The Advanced Technology Large Aperture Space Telescope (ATLAST) team has identified five key technologies to enable candidate architectures for the future large-aperture ultraviolet/optical/infrared (LUVOIR) space observatory envisioned by the NASA Astrophysics 30-year roadmap, Enduring Quests, Daring Visions. The science goals of ATLAST address a broad range of astrophysical questions from early galaxy and star formation to the processes that contributed to the formation of life on Earth, combining general astrophysics with direct-imaging and spectroscopy of habitable exoplanets. The key technologies are: internal coronagraphs, starshades (or external occulters), ultra-stable large-aperture telescopes, detectors, and mirror coatings. Selected technology performance goals include: 1x1010 raw contrast at an inner working angle of 35 milli-arcseconds, wavefront error stability on the order of 10 pm RMS per wavefront control step, autonomous on-board sensing & control, and zero-read-noise single-photon detectors spanning the exoplanet science bandpass between 400 nm and 1.8 μm. Development of these technologies will provide significant advances over current and planned observatories in terms of sensitivity, angular resolution, stability, and high-contrast imaging. The science goals of ATLAST are presented and flowed down to top-level telescope and instrument performance requirements in the context of a reference architecture: a 10-meter-class, segmented aperture telescope operating at room temperature (~290 K) at the sun-Earth Lagrange-2 point. For each technology area, we define best estimates of required capabilities, current state-of-the-art performance, and current Technology Readiness Level (TRL) - thus identifying the current technology gap. We report on current, planned, or recommended efforts to develop each technology to TRL 5.

Technology Development↗