Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “propeller aerodynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Aerodynamic Characteristics of a Four-Propeller Tilt-Wing VTOL Model with Twin Vertical Tails, Including Effects of Ground Proximity

Results are presented of a wind-tunnel investigation of the aerodynamic stability, control, and performance characteristics of a model of a four-propeller tilt-wing VTOL airplane employing flaps and speed brakes through the transition speed range. The results indicate that the wing was stalled for steady level flight for all conditions of the investigation; however, the flapped configuration did produce a higher maximum lift. The effectiveness of the flap in delaying the stall in the present investigation was not as great as in some previous investigations because the flap used was smaller than that used previously. The wing stall resulted in an appreciable reduction of aileron effectiveness during the transition. Out of ground effect the low horizontal tail did not appear to be in an adverse flow field as had been expected and showed no erratic changes in effectiveness; however, in ground effect a large nose-down moment was experienced by the model. In general, the lateral aerodynamic data indicate that the configuration is directionally stable and possesses positive dihedral effect throughout the transition, and the data show no signs of erratic flow at the vertical tails.

Grunwald, Kalman J.↗
NASA NTRS1956

An Analysis of Once-per-revolution Oscillating Aerodynamic Thrust Loads on Single-Rotation Propellers on Tractor Airplanes at Zero Yaw

A simplified procedure is shown for calculating the once-per-revolution oscillating aerodynamic thrust loads on propellers of tractor airplanes at zero yaw. The only flow field information required for the application of the procedure is a knowledge of the upflow angles at the horizontal center line of the propeller disk. Methods are presented whereby these angles may be computed without recourse to experimental survey of the flow field. The loads computed by the simplified procedure are compared with those computed by a more rigorous method and the procedure is applied to several airplane configurations which are believed typical of current designs. The results are generally satisfactory.

Rogallo, Vernon L↗
NASA NTRSDate not supplied

Comparison of Aerodynamic Analysis Tools Applied to a Propeller-Blown Wing

This paper describes initial results from an ongoing activity comparing two aerodynamic analysis tools: OVERFLOW, a Navier-Stokes flow solver, and FlightStream, a viscous surface-vorticity, unstructured panel method flow solver. Both tools are applied to analyses of an unblown wing and a propeller-blown wing, and then comparisons are performed between the predicted aerodynamic loads and moments from each tool. Computational performance and efficiencies of each tool and their usability in conceptual and preliminary air vehicle design are also discussed. A description of the workflow, underlying theoretical foundations, and best practices are provided. In comparing FlightStream and OVERFLOW, reasonable agreement between predicted performance is observed for flow regimes of interest at high angle of attack prior to stall, including blown wing aero-propulsive effects on lift augmentation and stall delay. In the post-stall regions, FlightStream appears to underestimate the effects of turbulent flow separation that contribute heavily to drag. However, as expected for a high-fidelity, time-accurate solver, the setup and computation time are substantially greater for OVERFLOW than for FlightStream.

Vivek Ahuja↗
NASA NTRSDate not supplied

Comparison of Aerodynamic Analysis Tools Applied to a Propeller-Blown Wing

This paper describes initial results from an ongoing activity comparing two aerodynamic analysis tools: OVERFLOW, a Navier-Stokes flow solver, and FlightStream, a viscous surface-vorticity, unstructured panel method flow solver. Both tools are applied to analyses of an unblown wing and a propeller-blown wing, and then comparisons are performed between the predicted aerodynamic loads and moments from each tool. Computational performance and efficiencies of each tool and their usability in conceptual and preliminary air vehicle design are also discussed. A description of the workflow, underlying theoretical foundations, and best practices are provided. In comparing FlightStream and OVERFLOW, reasonable agreement between predicted performance is observed for flow regimes of interest at high angle of attack prior to stall, including blown wing aero-propulsive effects on lift augmentation and stall delay. In the post-stall regions, FlightStream appears to underestimate the effects of turbulent flow separation that contribute heavily to drag. However, as expected for a high-fidelity, time-accurate solver, the setup and computation time are substantially greater for OVERFLOW than for FlightStream.

Vivek Ahuja↗
NASA NTRSDate not supplied

Static and Forced Oscillation Wind Tunnel Tests of A Tandem Propeller Configuration

A series of static and forced oscillation tests were conducted using a tandem propeller configuration in the NASA Langley 12-Foot Low-Speed Tunnel. The primary objectives were to quantify the effect of aerodynamic interactions on propeller thrust and identify conditions where the effect is most significant. A secondary objective was to obtain a preliminary data set from dynamic testing to assess the impact of angular rate on thrust performance. This paper presents analysis of the experimental data, which includes propeller performance measurements and qualitative flow visualization. The static results show that the rear propeller in the tandem configuration can experience thrust degradations greater than 30%. The extent of the wake interaction is a function of the hub separation distance and the advance ratio of the front propeller. Forced oscillation results showed that the front propeller exhibited primarily linear behavior across the conditions tested, whereas the rear propeller exhibited dynamic nonlinearity in the region of significant thrust degradation. These results are intended to support high-fidelity modeling research, particularly for flight dynamics simulation development to aid trajectory prediction, control design, and identification of hazardous conditions for multirotor vehicles.

Aerodynamic Interactions↗
NASA NTRS1996

PROP3D: A Program for 3D Euler Unsteady Aerodynamic and Aeroelastic (Flutter and Forced Response) Analysis of Propellers. Version 1.0

This guide describes the input data required, for steady or unsteady aerodynamic and aeroelastic analysis of propellers and the output files generated, in using PROP3D. The aerodynamic forces are obtained by solving three dimensional unsteady, compressible Euler equations. A normal mode structural analysis is used to obtain the aeroelastic equations, which are solved using either time domain or frequency domain solution method. Sample input and output files are included in this guide for steady aerodynamic analysis of single and counter-rotation propellers, and aeroelastic analysis of single-rotation propeller.

Srivastava, R.↗
NASA NTRS1988

NASA advanced propeller research

Acoustic and aerodynamic research at NASA Lewis Research Center on advanced propellers is reviewed including analytical and experimental results on both single and counterrotation. Computational tools used to calculate the detailed flow and acoustic fields are described along with wind tunnel tests to obtain data for code verification. Results from two kinds of experiments are reviewed: (1) performance and near field noise at cruise conditions as measured in the NASA Lewis 8- by 6-foot Wind Tunnel; and (2) far field noise and performance for takeoff/approach conditions as measured in the NASA Lewis 9- by 15-foot Anechoic Wind Tunnel. Detailed measurements of steady blade surface pressures are described along with vortex flow phenomena at off-design conditions. Near field noise at cruise is shown to level out or decrease as tip relative Mach number is increased beyond 1.15. Counterrotation interaction noise is shown to be a dominant source at takeoff but a secondary source at cruise. Effects of unequal rotor diameters and rotor-to-rotor spacing on interaction noise are also illustrated. Comparisons of wind tunnel acoustic measurements to flight results are made. Finally, some future directions in advanced propeller research such as swirl recovery vanes, higher sweep, forward sweep, and ducted propellers are discussed.

Groeneweg, John F.↗
NASA NTRS1988

NASA Advanced Propeller Research

Acoustic and aerodynamic research at NASA Lewis Research Center on advanced propellers is reviewed including analytical and experimental results on both single and counterrotation. Computational tools used to calculate the detailed flow and acoustic i e l d s a r e described along with wind tunnel tests to obtain data for code verification . Results from two kinds of experiments are reviewed: ( 1 ) performance and near field noise at cruise conditions as measured in the NASA Lewis 8-by 6-Foot Wind Tunnel and ( 2 ) farfield noise and performance for takeoff/approach conditions as measured in the NASA Lewis 9-by 15-Font Anechoic Wind Tunnel. Detailed measurements of steady blade surface pressures are described along with vortex flow phenomena at off design conditions . Near field noise at cruise is shown to level out or decrease as tip relative Mach number is increased beyond 1.15. Counterrotation interaction noise is shown to be a dominant source at take off but a secondary source at cruise. Effects of unequal rotor diameters and rotor-to-rotor spacing on interaction noise a real so illustrated. Comparisons of wind tunnel acoustic measurements to flight results are made. Finally, some future directions in advanced propeller research such as swirl recovery vanes, higher sweep, forward sweep, and ducted propellers are discussed.

Groeneweg, John F.↗
NASA NTRS1983

Propeller noise prediction

Analytic propeller noise prediction involves a sequence of computations culminating in the application of acoustic equations. The prediction sequence currently used by NASA in its ANOPP (aircraft noise prediction) program is described. The elements of the sequence are called program modules. The first group of modules analyzes the propeller geometry, the aerodynamics, including both potential and boundary layer flow, the propeller performance, and the surface loading distribution. This group of modules is based entirely on aerodynamic strip theory. The next group of modules deals with the actual noise prediction, based on data from the first group. Deterministic predictions of periodic thickness and loading noise are made using Farassat's time-domain methods. Broadband noise is predicted by the semi-empirical Schlinker-Amiet method. Near-field predictions of fuselage surface pressures include the effects of boundary layer refraction and (for a cylinder) scattering. Far-field predictions include atmospheric and ground effects. Experimental data from subsonic and transonic propellers are compared and NASA's future direction is propeller noise technology development are indicated.

Zorumski, W. E.↗
NASA NTRS1940

Full-Scale Tests of Several Propellers Equipped with Spinners, Cuffs, Airfoil and Round Shanks, and NACA 16-Series Sections, Special Report

Wind-tunnel tests of several propeller, cuff, and spinner combinations were conducted in the 20 foot propeller-research tunnel. Three propellers, which ranged in diameter from 8.4 to 11.25 feet, were tested at the front end of a streamline body incorporating spinners of two diameters. The tests covered a blade angle range from 20 deg to 65 deg. The effect of spinner diameter and propeller cuffs on the characteristics of one propeller was determined. Test were also conducted using a propeller which incorporated aerodynamically good shank sections and using one which incorporated the NACA 16 series sections for the outer 20 percent of the blades. Compressibility effects were not measured, owing to the low testing speeds. The results indicated that a conventional propeller was slightly more efficient when tested in conjunction with a 28 inch diameter spinner than with a 23 inch spinner, and that cuffs increased the efficiency as well as the power absorption characteristics. A propeller having good aerodynamic shanks was found to be definitely superior from the efficiency standpoint to a conventional round-shank propeller with or without cuffs; this propeller would probably be considered structurally impracticable, however. The propeller incorporating the NACA 16 series sections at the tims were found to have a slightly higher efficiency than a conventional propeller; the take-off characteristics appeared to be equally good. The effects noted above probably would be accentuated at helical speeds at which compressibility effects would enter.

Biermann, David↗
NASA NTRS1978

Analysis and test for space shuttle propellant dynamics: 1/60th scale model test results

During the abort sequence, the ET and orbiter separate under aerodynamic loading, with propellant remaining in the ET. The separation event included a seven second decelerating coast period during which the residual propellant accelerates relative to the ET/orbiter. At separation, ET clearance was primarily provided by aerodynamics acting on the ET to move it away. The motion of the propellant, primarily LOX, significantly influenced the resulting ET motion and could cause the ET to recontact the orbiter. A test program was conducted involving thirty-two drops with 1/60th scale models of the ET LOX tank. The objective was to acquire data on the nature of low g propellant reorientation, in the ET LOX tank, and to measure the forces exerted on the tank by the moving propellant.

Berry, R. L.↗
NASA NTRS2018

Aerodynamic Performance and Acoustic Measurements of a High-Lift Propeller in an Isolated Configuration

A series of aerodynamic performance and acoustic measurements has been made on a high-lift propeller intended for utilization on a distributed electric propulsion (DEP) aircraft. Tests were performed in the NASA Langley Low Speed Aeroacoustic Wind Tunnel (LSAWT), which has recently undergone a capability enhancement for the testing of small propellers/rotors and small unmanned aircraft system (UAS) platforms. The objectives of this testing campaign are two-fold: first to demonstrate the facility capabilities for performing small propeller aeroacoustic testing, and second to compare experimental measurements with computational fluid dynamic (CFD) predictions and CFD-based acoustic predictions of the tested propeller configurations for tool development and validation purposes.

Zawodny, Nikolas S.↗
NASA NTRS1956

Investigation of the Aerodynamic Characteristics of a Model Wing-Propeller Combination and of the Wing and Propeller Separately at Angles of Attack up to 90 Degrees

This report presents the results of an investigation conducted in the Langley 300 mph 7- by 10-foot wind tunnel for the purpose of determining the aerodynamic characteristics of a model wing-propeller combination, and of the wing and propeller separately at angles of attack up to 90 degrees. The tests covered thrust coefficients corresponding to free-stream velocities from zero forward speed to the normal range of cruising speeds. The results indicate that increasing the thrust coefficient increases the angle of attack for maximum lift and greatly diminishes the usual reduction in lift above the angle of attack for maximum lift.

Kuhn, Richard E↗
NASA NTRS1987

Experimental and theoretical study of propeller spinner/shank interference

A fundamental investigation into the aerodynamic interference associated with propeller spinner and shank regions has been conducted. The research program involved a theoretical assessment of solutions previously proposed, followed by a systematic experimental study to supplement the existing data base. As a result, a refined computational procedure has been established for prediction of interference effects in terms of either interference drag or propeller thrust and torque coefficients. These quantities have been examined with attention to engineering parameters such as spinner finess ratio, blade shank form, and number of blades. Also, cascade effects and spinner/shank juncture interference have been semi-empirically modeled using existing theories and placed into a compatible form with an existing propeller performance code.

Cornell, C. C.↗