SEARCH · Engineering Papers

Results for “plastic substrates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Heterogeneous microstructural evolution during hydrodynamic penetration of a high-velocity copper microparticle impacting copper

Microparticle hydrodynamic penetration (HDP) may be associated with the erosion regime in cold spray processing and other high-velocity impact events. Here, in an experimental approach where we can individually launch particles and study the impact sites, we explore copper microparticles impacted on copper substrates at velocities above 900 m/s where HDP begins. We lift cross-sectional lamellae from the impact sites with a focused-ion beam for further microstructural characterization using electron backscatter diffraction and scanning transmission electron microscopy. Due to the gradients of strain, strain rate, and temperature associated with HDP, heterogeneous microstructures result. The structural evolution processes observed include deformation twinning and multiple dislocation-mediated grain recrystallization mechanisms—geometric dynamic recrystallization (gDRX), discontinuous DRX (dDRX), and meta DRX (mDRX). The higher strains at the interface lead to the most significant structural changes and complex mechanisms. In contrast, there is a gradient to more conventional dislocation plasticity away from the interface (on either the particle or substrate side). Here, these microstructural observations are consistent with the deformation map for copper and extend the observations of impact-induced recrystallization across new regimes of behavior.

Cold spray process↗

NASA NTRS1979

Glass fiber reinforced concrete for terrestrial photovoltaic arrays

The use of glass-fiber-reinforced concrete (GRC) as a low-cost structural substrate for terrestrial solar cell arrays is discussed. The properties and fabrication of glass-reinforced concrete structures are considered, and a preliminary design for a laminated solar cell assembly built on a GRC substrate is presented. A total cost for such a photovoltaic module, composed of a Korad acrylic plastic film front cover, an aluminum foil back cover, an ethylene/vinyl acetate pottant/adhesive and a cotton fabric electrical isolator in addition to the GRC substrate, of $9.42/sq m is projected, which is less than the $11.00/sq m cost goal set by the Department of Energy. Preliminary evaluations are concluded to have shown the design capabilities and cost effectiveness of GRC; however, its potential for automated mass production has yet to be evaluated.

Maxwell, H.↗

DOE OSTI2021

Comparative performance of PETase as a function of reaction conditions, substrate properties, and product accumulation

There is keen interest to develop new technologies to recycle the plastic poly(ethylene terephthalate) (PET). To this end, the use of PET-hydrolyzing enzymes has shown promise for PET deconstruction to its monomers, terephthalate (TPA) and ethylene glycol (EG). Here, we compare the Ideonella sakaiensis PETase wild-type enzyme to a previously reported improved variant (W159H/S238F). We compare the thermostability of each enzyme and describe a 1.45 Å resolution structure of the mutant, highlighting changes in the substrate binding cleft compared to the wild-type enzyme. Subsequently, the performance of the wild-type and variant enzyme was compared as a function of temperature, substrate morphology, and reaction mixture composition. These studies show that reaction temperature has the strongest influence on performance between the two enzymes. We also show that both enzymes achieve higher levels of PET conversion for substrates with moderate crystallinity relative to amorphous substrates. Finally, we assess the impact of product accumulation on reaction progress for the hydrolysis of both PET and bis(2-hydroxyethyl) terephthalate (BHET). Each enzyme displays different inhibition profiles to mono(2-hydroxyethyl) terephthalate (MHET) and TPA, while both are sensitive to inhibition by EG. Overall, this work highlights the importance of reaction conditions, substrate selection, and product accumulation for catalytic performance of PET-hydrolyzing enzymes, which have implications for enzyme screening in the development of enzyme-based polyester recycling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Microstructure effects on high velocity microparticle impacts of copper

Constitutive models can fail to predict high-rate deformation behavior due to their inability to account for microstructural effects. In part, this is because of a dearth of experimental benchmarking data in the high strain-rate, low pressure regime, since many high-rate experiments also probe a region of strong shockwaves, at which point microstructure effects no longer play a primary role. This work uses laser-induced particle impact testing to quantitatively study high velocity impacts of small, rigid alumina microspheres on flat copper substrates with varying amounts of initial cold work in the weak shock regime, but at very high strain rates up to ~10 7 s –1 . Through paired experiments and numerical simulations, this work shows that the initial microstructure condition can have significant influence on dynamical mechanical properties in this range. Specifically, prior work hardening of the copper substrate leads to increased rebounding of the microparticles (i.e., less plastic dissipation in the impact) as well as smaller craters. Each of these experimental measurables can be converted into a strength measure, i.e., the dynamic yield strength or dynamic hardness, respectively, neither of which is well predicted consistently by existing constitutive laws. The general trend of hardening can be captured by such models by incorporating an existing “pre-strain,” suggesting that future calibration of the materials parameters may yield a good fit over a broader range of conditions. Our results emphasize the importance of reporting the microstructural condition in dynamic studies, as well as the necessity of accounting for these factors when formulating and optimizing constitutive models.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Sliding dynamics for bubble phases on periodic modulated substrates

We analyze a bubble-forming system composed of particles with competing long-range repulsive and short-range attractive interactions driven over a quasi-one-dimensional periodic substrate. We find various pinned and sliding phases as a function of substrate strength and drive amplitude. When the substrate is weak, a pinned bubble phase appears that depins elastically into a sliding bubble lattice. For stronger substrates, we find anisotropic bubbles, disordered bubbles, and stripe phases. Plastic depinning occurs via the hopping of individual particles from one bubble to the next in a pinned bubble lattice, and as the drive increases, there is a transition to a state where all of the bubbles are moving but are continuously shedding and absorbing individual particles. This is followed at high drives by a moving bubble lattice in which the particles can no longer escape their individual bubbles. The transition between the plastic and elastic sliding phases can be detected via signatures in the velocity-force curves, differential conductivity, and noise. When the bubbles shrink due to an increase in the attractive interaction term, they fit better inside the pinning troughs and become more strongly pinned, leading to a reentrant pinning phase. For weaker attractive terms, the size of the bubbles becomes greater than the width of the pinning troughs and the depinning becomes elastic with a reduced depinning threshold. Published by the American Physical Society 2024

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2024

Sliding Dynamics for Bubble Phases on Periodic Modulated Substrates

We analyze a bubble-forming system composed of particles with competing long-range repulsive and short range attractive interactions driven over a quasi-one-dimensional periodic substrate. We find various pinned and sliding phases as a function of substrate strength and drive amplitude. When the substrate is weak, a pinned bubble phase appears that depins elastically into a sliding bubble lattice. For stronger substrates, we find anisotropic bubbles, disordered bubbles, and stripe phases. Plastic depinning occurs via the hopping of individual particles from one bubble to the next in a pinned bubble lattice, and as the drive increases, there is a transition to a state where all of the bubbles are moving but are continuously shedding and absorbing individual particles. This is followed at high drives by a moving bubble lattice in which the particles can no longer escape their individual bubbles. The transition between the plastic and elastic sliding phases can be detected via signatures in the velocity-force curves, differential conductivity, and noise. When the bubbles shrink due to an increase in the attractive interaction term, they fit better inside the pinning troughs and become more strongly pinned, leading to a reentrant pinning phase. For weaker attractive terms, the size of the bubbles becomes greater than the width of the pinning troughs and the depinning becomes elastic with a reduced depinning threshold.

36 MATERIALS SCIENCE↗

NASA NTRS1983

FSA field test report, 1980 - 1982

Photovoltaic modules made of new and developing materials were tested in a continuing study of weatherability, compatibility, and corrosion protection. Over a two-year period, 365 two-cell submodules have been exposed for various intervals at three outdoor sites in Southern California or subjected to laboratory acceptance tests. Results to date show little loss of maximum power output, except in two types of modules. In the first of these, failure is due to cell fracture from the stresses that arise as water is regained from the surrounding air by a hardboard substrate, which shrank as it dried during its encapsulation in plastic film at 150 C in vacuo. In the second, the glass superstrate is sensitive to cracking, which also damages the cells electrostatically bonded to it; inadequate bonding of interconnects to the cells is also a problem in these modules. In a third type of module, a polyurethane pottant has begun to yellow, though as yet without significant effect on maximum power output.

Maxwell, H. G.↗

NASA NTRS1986

Ultrasonic Bonding to Metalized Plastic

New technique makes it possible to bond wires ultrasonically to conductor patterns on such soft substrates as plain or ceramic-filled polytetrafluoroethylene. With ultrasonic bonding, unpackaged chips attached to soft circuit boards. Preferred because chips require substrate area and better matched electrically to circuit board at high frequencies.

Conroy, B. L.↗

DOE OSTI2021

Evolutionary Diversification of Host-Targeted Bartonella Effectors Proteins Derived from a Conserved FicTA Toxin-Antitoxin Module

Proteins containing a FIC domain catalyze AMPylation and other post-translational modifications (PTMs). In bacteria, they are typically part of FicTA toxin-antitoxin modules that control conserved biochemical processes such as topoisomerase activity, but they have also repeatedly diversified into host-targeted virulence factors. Among these, Bartonella effector proteins (Beps) comprise a particularly diverse ensemble of FIC domains that subvert various host cellular functions. However, no comprehensive comparative analysis has been performed to infer molecular mechanisms underlying the biochemical and functional diversification of FIC domains in the vast Bep family. Here, we used X-ray crystallography, structural modelling, and phylogenetic analyses to unravel the expansion and diversification of Bep repertoires that evolved in parallel in three Bartonella lineages from a single ancestral FicTA toxin-antitoxin module. Our analysis is based on 99 non-redundant Bep sequences and nine crystal structures. Inferred from the conservation of the FIC signature motif that comprises the catalytic histidine and residues involved in substrate binding, about half of them represent AMP transferases. A quarter of Beps show a glutamate in a strategic position in the putative substrate binding pocket that would interfere with triphosphate-nucleotide binding but may allow binding of an AMPylated target for deAMPylation or another substrate to catalyze a distinct PTM. The β-hairpin flap that registers the modifiable target segment to the active site exhibits remarkable structural variability. The corresponding sequences form few well-defined groups that may recognize distinct target proteins. The binding of Beps to promiscuous FicA antitoxins is well conserved, indicating a role of the antitoxin to inhibit enzymatic activity or to serve as a chaperone for the FIC domain before translocation of the Bep into host cells. Taken together, our analysis indicates a remarkable functional plasticity of Beps that is mostly brought about by structural changes in the substrate pocket and the target dock. These findings may guide future structure–function analyses of the highly versatile FIC domains.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS2018

Plasticity and Damage Modeling of Stress Asymmetry and Dynamic Behavior of AFS Additive Manufactured Aluminum Alloy 2219

The Solid State Additive Manufacturing (AM) process referred as MELD that fabricated the samples in this study, provides a new path for repairing, coating, joining and additive manufacturing metals and metal matrix composites. This research will be the first application of a physics-based microstructure dependent internal state variable (ISV) plasticity and damage material model to capture the mechanical response of an AM Aluminum Alloy (AA) 2219 via the MELD process. In this research, a microstructure-based internal state variable (ISV) plasticity-damage model was used to capture the mechanical behavior of AFS 2219 aluminum alloy. Aeroprobe Corporation, creator and patent holder for the MELD process, fabricated the material by pushing a solid filler rod of AA2219-T861 material through a hollow rotating tool onto an AA2219 T851 plate substrate. As feedstock, solid or powder precursor metals are pushed through a nonconsumable rotating cylindrical tool. Herein, added layers are deposited and metallurgically bonded to substrate material or previously deposited layers by the heat generated from the rotating tool through plastic deformation of the filler material. Once a layer has been added, the tool height increases, and starts the deposition of the next layer. This process results in beneficial properties such as grain refinement, homogenization and reduced porosity (fully dense). This process will experience temperatures similar to those in the weld nugget zone (WNZ) in friction stir welding (FSW), ranging from 0.6-0.9 Tm, with Tm being the melting point of the material. MELD is highly scalable with AA deposition rates reaching over 1000 cm3/hr, which allows for MELD being used for repairs, coatings, and building components. A motivating factor driving the research for physics-based history dependent material modeling of MELD components is the ability to accurately capture the stress-state and strain rate dependence in the material caused by variations in material microstructure from the MELD processing of new or repaired components. The ISV model incorporates microstructural content and is consistent with continuum level kinematics, kinetics, and thermodynamics. These features allow the ISV model to capture large deformations at the structural scale using the kinematic and isotropic hardening, while microscale damage is obtained from the microstructural features. The benefits of the ISV model arise from the inclusion of structure-property relationships identified from microstructural characterization and experimentation. The Bauschinger effect (BE) is an important concept, vital in the accurate prediction of cyclic stress-strain response of ductile materials such as metals. The ISV model has been successfully used to capture the behavior and damage, and the BE of different aluminum alloys and steels. The ISV model uses kinematic and isotropic hardening to help capture deformations of the material at the macro scale. To understand this hardening relationship, calculating the kinematic and isotropic hardening relationship in the material is warranted for a high-fidelity model. Electron Backscattered Diffraction (EBSD) was used to characterize the as-fabricated microstructure, where a fully-dense equiaxed grain morphology with average grain size of 2.5 μm was observed. Microhardness mapping of the as-built structures, monotonic tension and compression experiments at both quasi-static (0.001/s) strain rates, tension-followed-by-compression and compression-followed-by-tension experiments were performed to obtain the set of plasticity and damage constants necessary to capture strain rate and stress state behavior of this additive material. To calibrate the plasticity-damage model, a single set of constants were determined to capture the different stress states the MELD AA2219. One set of the constants was determined from experimental true stress-strain curves for the tension and compression data. Additionally, microstructural information and data from the open literature were used as the other model constants. This research is a first of its kind for AFS AA2219, includes correlating the ISV model to the monotonic experimental results that capture the isotropic and kinematic plasticity mechanical response.

Rivera, O. G.↗

NASA NTRS1976

Material and design considerations of encapsulants for photovoltaic arrays in terrestrial applications

Procedures for analyzing cyclic mechanical stresses in encapsulated photovoltaic arrays designed for terrestrial application are discussed. The concept of 'thermal stiffness', the product of alpha and Young's modulus, is presented, and its usefulness for minimizing mechanical stresses is demonstrated. The concept of the 'proportional-limit' helps indicate the upper limit of design stress for plastics. System design is considered with attention to cell dimensions, cell to substrate adhesive, single encapsulant system, double layer encapsulant, and stresses in the interconnects. The permeability of polymeric materials to gases is examined.

Carroll, W.↗

NASA NTRS2001

Development of a fully integrated analysis system for ions based on ion-selective optodes and centrifugal microfluidics

A fully integrated, miniaturized analysis system for ions based on a centrifugal microfluidics platform and ion-selective optode membranes is described. The microfluidic architecture is composed of channels, five solution reservoirs, a measuring chamber, and a waste reservoir manufactured onto a disk-shaped substrate of poly(methyl methacrylate). Ion-selective optode membranes, composed of plasticized poly(vinyl chloride) impregnated with an ionophore, a proton chromoionophore, and a lipophilic anionic additive, were cast, with a spin-on device, onto a support layer and then immobilized on the disk. Fluid propulsion is achieved by the centrifugal force that results from spinning the disk, while a system of valves is built onto the disk to control flow. These valves operate based on fluid properties and fluid/substrate interactions and are controlled by the angular frequency of rotation. With this system, we have been able to deliver calibrant solutions, washing buffers, or "test" solutions to the measuring chamber where the optode membrane is located. An analysis system based on a potassium-selective optode has been characterized. Results indicate that optodes immobilized on the platform demonstrate theoretical responses in an absorbance mode of measurement. Samples of unknown concentration can be quantified to within 3% error by fitting the response function for a given optode membrane using an acid (for measuring the signal for a fully protonated chromoionophore), a base (for fully deprotonated chromoionophore), and two standard solutions. Further, the ability to measure ion concentrations by employing one standard solution in conjunction with acid and base and with two standards alone were studied to delineate whether the current architecture could be simplified. Finally, the efficacy of incorporating washing steps into the calibration protocol was investigated.

NASA Discipline Life Sciences Technologies↗

DOE OSTI2026

A Catabolic Powerhouse for Biorefineries: Characterization and Engineering Erwinia spp. Strain LJJL01 to Produce Bioproducts

Nonmodel microbial hosts can efficiently biotransform unconventional organic feedstocks into advanced bioproducts, leveraging their superior metabolic capabilities and resilience to process-relevant physicochemical conditions. In this study, we domesticated Erwinia spp. strain. LJJL01 (Er LJJL01) as a potent microbial chassis to advance the emerging biorefinery strategy for the valorization of lignin-rich biomass and plastic, thereby enabling the circular economy. The strain exhibits remarkable chemical tolerance and can biofunnel various substrates, including sugars, acids, polyols, and aromatics, in minimal salt media to produce native fine chemicals such as acetoin, 2,3-butanediol, and lactic acid. As a proof of concept, engineering this strain with advanced genetic tools enables the production of tailored high-value chemicals, such as cis,cis-muconate from plastic-derived terephthalate and polyhydroxybutyrate from lignocellulosic hydrolysate. We established Er LJJL01 as a potent microbial chassis for the green synthesis of bioproducts from unconventional organic feedstocks.

09 BIOMASS FUELS↗

NASA NTRS1983

Development of a large scale bipolar NiH2 battery

The bipolar battery concept, developed in cooperation with NASA, is described in the context of the advantages afforded by near-term IPV and CVP cell technology. The projected performance, development requirements, and a possible approach to bipolar battery design are outlined. Consideration is given to packaging electrodes within a common hydrophobic plastic frame, electrode technology that involves a photochemically etched 0.1 mm thick nickel substrate coated with a 10 mg/sq cm mixture of platinum powder and TFE30, and an electrode design that eliminates the screen and doubles the electrode thickness (from the currently used 0.8 mm) while retaining the active material loading of 1.6-1.8 gm/cu cm. Also covered are thermal management, and electrolyte and oxygen management. It is concluded that a high voltage, high capacity, bipolar NiH2 cell can be configured with proper development for use in large power systems, and that it can provide considerable weight savings.

Adler, E.↗

DOE OSTI2025

Interlayer Exciton Polarons in Mesoscopic V 2 O 5 for Broadband Optoelectronic Synapses

Persistent photoconductivity and optoelectronic synaptic behavior are demonstrated in solution-processed mesoscopic α-phase vanadium pentoxide (V 2 O 5 ) thin films. First-principles simulations coupled with the two-site Holstein polaron hopping model show that vacancies at the terminal oxygen position lead to long recombination times because photoexcited electrons and holes reside on different layers separated by the van der Waals gap, forming a weakly coupled interlayer exciton polaron. Mid-gap polaronic states also significantly broaden the photoresponse of the films to span across visible and infrared wavelengths. By controlling the amplitude/intensity, duration, and/or number of optical pulses, tunable optoelectronic memory functions, such as short-term and long-term plasticity, are experimentally established in V 2 O 5 -based optoelectronic synapses. Furthermore, device fabrication was extended to mechanically flexible ultrathin glass substrates. Flexible optoelectronic synapses maintained high performance after 150 bending cycles.

Phan, Thanh Luan [National Renewable Energy Labora↗

NASA NTRSDate not supplied

Alternative Setup for Long-Duration Low-Duty-Cycle 600°C Ambient Testing of SiC Integrated Circuits

A scalable, compact oven testbed system for simultaneously evaluating a multitude of high temperature integrated circuits (ICs) for prolonged operating times of up to 600 °C has been prototyped. The new testbed system enables long-duration high temperature testing in sufficient statistical quantities consistent with standard aerospace electronics engineering standards. This setup is comprised of multiple compact ovens housing chips or packages mounted to ceramic circuit boards. Each oven is a compact 15.2 cm length by 15.2 cm width by 12.7 cm depth with a maximum 400 Watts of heating power. The custom-made silicon oxide ceramic heating block inside each oven is based on a 3D printed design adapted for the easy insertion of the IC device under test (DUT). This innovative design provides the quick insertion of ICs with or without a ceramic package into a 600 °C environment by utilizing a movable 11.43 cm long ceramic substrate with electrical traces extending from the oven hot zone to external standard plastic-based board connectors. Another key oven design feature is the minimization of the DUT exposure to electromagnetic interference (EMI) by utilizing a filtered DC power source to reduce heating element noise. Additionally, the ovens can be configured in a parallel arrangement allowing global data monitoring over a single industrial RS422 serial port. This feature is important for scaling up to test multiple ICs semi-simultaneously. A USB serial port is provided to independently control the operating parameters of each oven such as the oven target temperature and oven ramp rate. The oven temperature can reach up to 600 °C with a confirmed +/- 4 °C maximum deviation across the test zone region. The ramp rate can be programmed from 1 °C/minute up to 10 °C/minute. Furthermore, a programmable switchboard is used to interface with the DUT. This switchboard comprises a National Instruments Peripheral Component Interconnect eXtension for Instrumentation (NI PXI) system and a breakout board to send and receive power, analog or digital test signals. By using this unique oven testbed system, a variety of ICs can now be tested in parallel using the same test components configured for a diverse set of requirements.

DC Powered Oven↗

DOE OSTI2023

Carbon Fiber Reinforced Plastic with Substantially Improved Through-plane Thermal Conductivity

Thermal conductivity of carbon fiber support structures that also serve as cooling substrates is of increasing importance for high energy physics detectors. One of the shortcomings of current carbon fiber laminates is that they exhibit excellent thermal conductivity of order several hundred W/(m*K) along the fiber direction, whereas the through plane thermal conductivity perpendicular to the fibers is orders of magnitude lower, and at about 1 W/(m*K) more in the range of thermal insulators. This proposal aims to significantly improve the through plane thermal conductivity, by at least a factor five, changing CFRP from being a thermal insulator to a thermal conductor in the through plane direction. Between June 2021 and December 2022, a total of 36 carbon fiber laminate test samples and two carbon loaded epoxy test samples were manufactured and analyzed for thermal performance. Unfortunately, the promising results obtained with a similar sample manufactured in 2017 were not reproduced. We believe this to be mainly due the excessive age of the carbon fiber prepreg material used for this SBIR - the same material batch, produced in 2015, was used in 2017 and in 2021/2022, i.e. the material was seven years old when the final samples were produced - , and to a lesser degree to the difference in pressure attainable with the 2017 and 2021/2022 laminate curing setups. While disappointing, the results are not completely discouraging, since for the samples with the highest compression the through-plane thermal conductivities plotted as a function of per-ply thickness extrapolate well to the data point from the 2017 sample.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2026

Elucidating biodegradation of dimethyl terephthalate by two Rhodococcus strains for its valorization applications

Dimethyl terephthalate (DMT) serves as the precursor in the production of polyethylene terephthalate, polytrimethylene terephthalate, and polybutylene terephthalate. The widespread use of DMT in the polymer industry and its ubiquitous existence in end products raise alarms about its potential harm to humans and animals. DMT can enter the environment through the degradation of polymers and their end products, and cause endocrine disruption, oxidative stress, and an elevated risk of cancer. In recent years, DMT has also gained renewed interest in its potential for plastic recycling and upcycling. In this study, we identified two strains of Rhodococcus that possess DMT-degrading capabilities and utilized transcriptomic analysis and gene knockout to elucidate the mechanisms of DMT degradation. R. opacus PD630 and R. jostii RPET were found to convert up to 1 g/L DMT into mono-methyl terephthalate (MMT). A putative DMTase (RS34275) was identified for this conversion. R. jostii RPET also demonstrates the ability to convert DMT into MMT and to utilize MMT for its cellular growth via the terephthalate pathway. A putative MMTase (RS21885) as the sole enzyme was identified for the conversion of MMT into terephthalate in the RPET strain. In addition, we successfully produced lycopene and lipids from an engineered RPET strain using DMT as a substrate. Our findings will facilitate future DMT bioremediation and bio-upcycling of DMT-associated plastics, enabling the production of value-added products.

Biodegradation↗