Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phosphide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Electronic impact of Ni2P nanoparticle size on hydrogenation rates

Nickle phosphide, Ni2P, nanoparticles supported on SiO2 show a marked volcano shaped size dependence. Kinetic analysis and physicochemical characterization shows the electron density of Ni to increase with increasing Ni2P size, enhancing in turn the H2 adsorption strength. For particles below 15 nm, H adsorbs weakly causing a low surface coverage of H, gradually increasing with particle size. For large particles, hydrogen binds too strongly causing a high coverage but low catalytic activity. The remarkable size dependence of the electronic properties show that Ni2P particle size can be used to fine-tune its activity for hydrogenation.

Ni2P size effect, Electron density, H2 adsorption ↗
DOE OSTI2022

On the Effects of Aliovalent Substitutions in Thermoelectric Zintl Pnictides. Varied Polyanionic Dimensionality and Complex Structural Transformations–The Case of Sr 3 ZnP 3 vs Sr 3 Al x Zn 1– x P 3

The structures and the transport properties of a novel family of Zintl phosphides and arsenides with the formula AE 3 ZnPn 3 and the solid solutions AE 3 Al x Zn 1–x Pn 3 , AE 3 ZnAs y P 1–y (AE = Sr, Eu; Pn = P, As) are reported. Crystals of nine new phases have been obtained via Pb-flux reactions and used for structural work by means of single-crystal X-ray diffraction methods. The derived orthorhombic structure is without a direct analog, and features unusual structural units, where the Zn atoms are in both distorted tetrahedral and trigonal-planar coordination of pnictogens. Electronic structure calculations reveal moderately wide bandgaps for Sr 3 ZnP 3 and Sr 3 ZnAs 3 , on the order of 0.70 and 0.63 eV, respectively. Electrical transport measurements above room temperature indicate relatively high resistivity values above 500 K (ρ ≈ 4.8 Ω cm and above), but some of the samples exhibit very high Seebeck coefficients, as large as 300 μV/K at 560 K for Sr 3 ZnAs 3 . Aliovalent substitutions in AE 3 ZnPn 3 , achieved by the partial replacement of Zn 2+ with Al 3+ cations promote occupational and positional disorder, which causes structural transformation towards the disordered variant of the Sr 5 Al 2 Sb 6 structure type. Such substitutions also change the dimensionality of the polyanionic sub-lattice in the resulting quaternary AE 3 Al x Zn 1–x Pn 3 phases. Furthermore, preliminary transport property data on the latter reveal nine times lower electrical resistivity (ρ 500 ≈ 0.5 Ω cm) together with a significantly enhanced Seebeck coefficient, αmax ≈ 430 μV/K at 560 K.

36 MATERIALS SCIENCE↗
DOE OSTI2024

FeSi 4 P 4 and CoSi 3 P 3 : Hidden Gems of Ternary Tetrel Pnictides with Outstanding Nonlinear Optical Properties

Metal silicon phosphides have shown promise as nonlinear optical materials. To be practically useful and cheap, earth-abundant 3d transition metals are preferred over their scarcer and more expensive 4d and 5d counterparts. Here, we developed a synthetic method to produce polycrystalline bulk powders and millimeter-sized single crystals of ternary compounds FeSi 4 P 4 and CoSi 3 P 3 . Both studied compounds have noncentrosymmetric and chiral crystal structures with ordered Si/P arrangements as was confirmed by single-crystal X-ray diffraction and solid-state NMR. Despite the presence of the transition metal, FeSi 4 P 4 and CoSi 3 P 3 are semiconductors with direct band gaps of 1.3 and 1.6 eV, respectively, indicating low-spin d 6 electronic configuration for octahedral Fe 2+ and Co 3+ . Relative to reported sulfide materials, FeSi 4 P 4 and CoSi 3 P 3 small band gap semiconductors demonstrate an outstanding combination of second-harmonic generation (SHG) activity and laser damage threshold (LDT). Both studied materials are phase-matchable with a 2.09 μm laser and not only exhibit 2.5–3.0 times stronger SHG signal than that of the state-of-the-art AgGaS 2 standard but also demonstrate an LDT response of 2.3–2.5 times higher than that of AgGaS 2 (at 1.09 μm laser with a pulse width of 10 ns)-which is unprecedented for small band gap semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Crystal Structure and Properties of Layered Pnictides BaCuSi2Pn3 (Pn = P, As)

Two novel layered compounds BaCuSi 2 Pn 3 (Pn = P, As) adopting new structure types are reported. As revealed by single-crystal X-ray diffraction, both compounds are composed of unique Cu–Si–Pn layers featuring CuPn 3 and Si 2 Pn 6 structural motifs found in other archetypal pnictide materials. The stacking of the isostructural Cu–Si–Pn layers is different for phosphide and arsenide compounds. Synthesis from elements aided by in situ synchrotron powder X-ray diffraction resulted in the obtainment of bulk powders with a minimized amount of admixtures. Experimentally measured physical properties of BaCuSi 2 As 3 unexpectedly showed metal-like behavior at temperatures above 15 K, despite the fact that density functional theory calculations predict a small band gap of 0.4 eV. BaCuSi 2 As 3 exhibits ultralow thermal conductivity, which can be explained by the combination of a layered crystal structure with alternating covalent and ionic bonding, which feature rattling of Cu atoms similar to that in tetrahedrites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

From Serendipity to Exploration: Synthesis and Properties of PtSiSb

PtSiSb is a compound with covalent Si–Sb bonds, which are relatively rare instances in solid-state materials. The original report on PtSiSb indicates synthetic challenges for the isolation of single-phase samples, as well as potential discrepancies in the predicted electronic structure and experimental transport properties. In this work, we considered PtSiSb as a case study with the objective of demonstrating the importance of synthesis as a bridge between theoretical predictions and experimental properties. Using guidance from in situ powder X-ray diffraction, the synthesis of single-phase polycrystalline samples was developed, allowing further experimental characterization of transport and catalytic properties. Thermal conductivity and heat capacity demonstrated anomalous behavior, indicating an unconventional phonon scattering mechanism in PtSiSb. Charge transport measurements indicated semimetallic behavior. Hydrogen evolution reaction (HER) tests in acidic electrolyte revealed that the PtSiSb cathode needs an overpotential η 10 = 120 mV to achieve a current density j = −10 mA/cm 2 . This is lower activity than elemental Pt but comparable to known and active transition-metal phosphide HER catalysts, such as CoP, with η 10 = 93 mV when measured at identical conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Creation of an Fe 3 P Schreibersite Density Functional Tight Binding Model for Astrobiological Simulations

The mineral schreibersite, e.g., Fe 3 P, is commonly found in iron-rich meteorites and could have served as an abiotic phosphorus source for prebiotic chemistry. However, atomistic calculations of its degradation chemistry generally require quantum simulation approaches, which can be too computationally cumbersome to study sufficient time and length scales for this process. In this regard, we have created a computationally efficient semiempirical quantum density functional tight binding (DFTB) model for iron and phosphorus-containing materials by adopting an existing semiautomated workflow that represents many-body interactions by linear combinations of Chebyshev polynomials. Here, we have utilized a relatively small training set to optimize a DFTB model that is accurate for schreibersite physical and chemical properties, including its bulk properties, surface energies, and water absorption. We then show that our model shows strong transferability to several iron phosphide solids as well as multiple allotropes of iron metal. Our resulting DFTB parametrization will allow us to interrogate schreibersite aqueous decomposition at longer time and length scales than standard quantum approaches, providing for more detailed investigations of its role in prebiotic chemistry on early Earth.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In Situ Studies of the Formation of MoP Catalysts and Their Structure under Reaction Conditions for Higher Alcohol Synthesis: The Role of Promoters and Mesoporous Supports

Three formulations of a molybdenum phosphide (MoP) catalyst system were characterized for the higher alcohol synthesis (HAS) reaction using in situ X-ray absorption spectroscopy (XAS) and X-ray diffraction (XRD), monitoring the chemical phase evolution during activation and under reaction conditions. Here, the in situ study herein provides important insights into the effect of the support and of K that lead to high performance in HAS for K-promoted MoP supported on carbon, as evidenced by previous studies (ethanol selectivity: 29%; conversion: 5%). During the activation process, XAS shows that the carbon-supported samples reduce and reach a highly crystalline state at a lower temperature than the SBA-15-supported sample, indicating a substantial difference in catalyst activation. After activation, the samples are introduced to relevant reaction conditions resulting in spectra fairly similar to one another. XRD results corroborate the difference in the degree of crystallinity of these samples, in alignment with the XAS, and reveal the formation of crystalline potassium pyrophosphate (K 4 P 2 O 7 ) during the activation period of the K-promoted samples. This K 4 P 2 O 7 phase remains present under reaction conditions. Taken together, these results provide insights into the roles played by the carbon support and K promotion, connecting activity to electronic and crystal structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Magneto-optical Evidence of the Tilting Effect in Coupled Weyl Bands

Theories have revealed the universality of the band tilting effect in topological Weyl semimetals (WSMs) and its implications for the material physical properties. However, the experimental identification of tilted Weyl bands remains less explored. Here, we report the magneto-optical evidence of the tilting effect in WSM niobium phosphide. Specifically, we observe Landau level transitions with rich features that are well reproduced within a model of coupled tilted Weyl points. Our analysis indicates that the tilting effect relaxes the selection rules and leads to transitions that would otherwise be forbidden in the non-tilt case. Additionally, we observe unconventional interband transitions with flat and negative magnetic field dispersions, highlighting the importance of coupling between Weyl points. Our results not only emphasize the significance of the tilting effect in the optical responses of WSMs but also demonstrate magneto-optics as an effective tool for probing the tilting effect in electronic band structures.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Co 2 P-Pt Heterostructure Interfaces for Electrocatalytic Hydrogen Evolution

Pt-based electrocatalysts are effective for the hydrogen evolution reaction (HER); however, their limited ability to facilitate water dissociation and suboptimal hydrogen binding energy (H BE ) in alkaline electrolytes result in slow reaction kinetics, which hinders their cost-efficiency and practical applications. This study reports the synthesis of Co 2 P-Pt heterostructure nanorods using a seed-mediated growth method, producing a high density of Co 2 P-Pt interfacial sites. Density functional theory (DFT) calculations indicate that electronic interactions at these interfaces optimize H BE on Pt, while the interfacial sites promote water dissociation. The Co 2 P-Pt nanorods demonstrate an overpotential of 14 mV at 10 mA cm −2 for the HER, highlighting the potential of precisely engineered metal-metal phosphide interfaces for enhancing electrocatalytic efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Advances in Colloidal InP-Based Quantum Dots for Photocatalytic Hydrogen Evolution

Photocatalytic materials for hydrogen generation are typically categorized into UV-absorbing metal oxides and visible-range semiconductors such as chalcogenides or perovskites, which often incorporate toxic elements. To address environmental concerns of the latter group, indium phosphide (InP)-based quantum dots (QDs) have recently emerged as a less toxic alternative. These nanocrystals (NCs) benefit from a broadband and tunable absorption spectrum, which is well matched for solar photochemistry, and offer suitable electronic characteristics to drive photoinduced charge separation. This perspective provides a comprehensive summary of the recent advancements in developing InP-based NCs with a focus on photocatalytic hydrogen production. We discuss synthetic strategies that enhance the catalytic activity of these materials and highlight key challenges that must be addressed to enhance their performance. Finally, we explore future research directions aimed at improving photocatalytic efficiency and integrating InP-based QDs into practical solar-to-fuel conversion systems.

Hydrogen↗
DOE OSTI2020

Quantized thermoelectric Hall effect induces giant power factor in a topological semimetal

Abstract Thermoelectrics are promising by directly generating electricity from waste heat. However, (sub-)room-temperature thermoelectrics have been a long-standing challenge due to vanishing electronic entropy at low temperatures. Topological materials offer a new avenue for energy harvesting applications. Recent theories predicted that topological semimetals at the quantum limit can lead to a large, non-saturating thermopower and a quantized thermoelectric Hall conductivity approaching a universal value. Here, we experimentally demonstrate the non-saturating thermopower and quantized thermoelectric Hall effect in the topological Weyl semimetal (WSM) tantalum phosphide (TaP). An ultrahigh longitudinal thermopower $$S_{xx} \sim 1.1 \times 10^3 \, \mu \, {\mathrm{V}} \, {\mathrm{K}}^{ - 1}$$ S x x ~ 1.1 × 1 0 3 μ V K − 1 and giant power factor $$\sim 525 \, \mu \, {\mathrm{W}} \, {\mathrm{cm}}^{ - 1} \, {\mathrm{K}}^{ - 2}$$ ~ 525 μ W cm − 1 K − 2 are observed at ~40 K, which is largely attributed to the quantized thermoelectric Hall effect. Our work highlights the unique quantized thermoelectric Hall effect realized in a WSM toward low-temperature energy harvesting applications.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Heteroepitaxial chemistry of zinc chalcogenides on InP nanocrystals for defect-free interfaces with atomic uniformity

Heteroepitaxy on colloidal semiconductor nanocrystals is an essential strategy for manipulating their optoelectronic functionalities. However, their practical synthesis typically leads to scattered and unexpected outcomes due to the intervention of multiple reaction pathways associated with complicated side products of reactants. Here, the heteroepitaxy mechanism of zinc chalcogenide initiated on indium phosphide (InP) colloidal nanocrystals is elucidated using the precursors, zinc carboxylate and trialkylphosphine selenide. The high magnetic receptivity of 77 Se and the characteristic longitudinal optical phonon mode of ZnSe allowed for monitoring the sequence of epilayer formation at the molecular level. The investigation revealed the sterically hindered acyloxytrialkylphosphonium and diacyloxytrialkylphosphorane to be main intermediates in the surface reaction, which retards the metal ion adsorption by a large steric hindrance. The transformation of adsorbates to the crystalline epilayer was disturbed by surface oxides. Raman scattering disclosed the pathway of secondary surface oxidation triggered by carboxylate ligands migrated from zinc carboxylate. The surface-initiated heteroepitaxy protocol is proposed to fabricate core/shell heterostructured nanocrystals with atomic-scale uniformity of epilayers. Despite the large lattice mismatch of ZnS to InP, we realised a uniform and interface defect-free ZnS epilayer (~0.3 nm thickness) on InP nanocrystals, as evidenced by a high photoluminescence quantum yield of 97.3%.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Optomechanical ring resonator for efficient microwave-optical frequency conversion

Phonons traveling in solid-state devices are emerging as a universal excitation for coupling different physical systems. Phonons at microwave frequencies have a similar wavelength to optical photons in solids, enabling optomechanical microwave-optical transduction of classical and quantum signals. It becomes conceivable to build optomechanical integrated circuits (OMIC) that guide both photons and phonons and interconnect photonic and phononic devices. Here, we demonstrate an OMIC including an optomechanical ring resonator (OMR), where co-resonant infrared photons and GHz phonons induce significantly enhanced interconversion. The platform is hybrid, using wide bandgap semiconductor gallium phosphide (GaP) for waveguiding and piezoelectric zinc oxide (ZnO) for phonon generation. The OMR features photonic and phononic quality factors of >1 × 10 5 and 3.2 × 10 3 , respectively. The optomechanical interconversion between photonic modes achieved an internal conversion efficiency $η_i$ = (2.1 ± 0.1)% and a total device efficiency $η_{tot}$ = 0.57 x 10 -6 at a low acoustic pump power of 1.6 mW. The efficient conversion in OMICs enables microwave-optical transduction for quantum information and microwave photonics applications.

42 ENGINEERING↗
DOE OSTI2026

Efficient bidirectional quantum frequency conversion between telecom and visible bands using adaptively phase-matched III-V nanophotonic waveguides

Quantum frequency conversion (QFC) is essential for interfacing quantum systems operating at different wavelengths and for realizing scalable quantum networks. Despite extensive progress, achieving QFC with simultaneous high efficiency, low pump power, minimal noise, broad bandwidth, and pump-wavelength flexibility remains challenging. Here, we demonstrate efficient, low-noise, and bidirectional QFC between the telecom (1550-nm) and visible (780-nm) bands using unpoled indium gallium phosphide (InGaP) χ (2) nanophotonic waveguides, eliminating the need for a long-wavelength pump. Leveraging the large nonlinear susceptibility of InGaP together with adaptive phase-matching control, we obtain 27% (55%) internal efficiency in a 6-mm (2.5-mm)-long waveguide with a low pump power of 20 mW (50 mW) and a noise flux spectral density of 10 −4 counts per second per hertz at signal–pump detuning of 20 nm. These results mark a significant advance in integrated nonlinear photonics for high-performance QFC, facilitating the development of versatile and scalable quantum networks.

Hu, Jierui [Univ. of Illinois at Urbana-Champaign,↗
DOE OSTI2021

Transition metal-based bimetallic MOFs and MOF-derived catalysts for electrochemical oxygen evolution reaction

The oxygen evolution reaction (OER) is a critical electrochemical reaction in water splitting and rechargeable metal–air batteries. It plays a pivotal role in achieving high-efficiency clean-energy production and energy storage in these devices. Transition metal-based bimetallic MOFs (TMB MOFs) with two different metal ions possess specific synergistic effects, which could exhibit OER performance and stability superior to those of the corresponding monometallic MOFs for water oxidation. Benefiting from the diversity of chemical composition and structural type, TMB MOFs can also serve as precursors and templates to obtain alloy-particle-decorated carbon materials with high surface area, or metal compounds such as bimetallic sulfides, phosphides, and hydroxides with atomic-level mixing of heterometallic elements. These materials with high-density active sites exhibit much improved catalytic activity in the water oxidation reaction. Furthermore, this article aims to review the recent progress with TMB MOFs and their derivatives in relation to applications as electrocatalysts in OER, including analysis of the mechanism of the OER process with the assistance of DFT calculations and in situ or operando techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantifying the reaction mechanisms of a high-capacity CuP 2 /C composite anode for potassium ion batteries

Introducing metals into phosphorus to form metal phosphide materials as anodes for potassium ion batteries (PIBs) is an effective strategy to improve the electronic conductivity and alleviate the volume change during cycling, although with a compromise of capacity. Here in this paper, we explore a CuP 2 /C composite as a novel anode for PIBs, which delivers a high reversible capacity of >450 mA h g -1 . Unexpectedly, our results reveal that the POx components existing in the prepared composite are reversible, through a quantitative analysis via high-resolution solid-state 31 P NMR and synchrotron X-ray diffraction tests. Their potassiation products K 3 PO 4 and K 4 P 2 O 7 can react with K–P alloys and turn back to PO x during depotassiation, which probably accounts for the high capacity of the prepared material. The results also illustrate a crystallization–amorphization evolution process during cycling involving nanocrystalline α-K 4 P 6 , K 4 P 3 and KP, and amorphous K 4 P 6 , KP and K 3 P phases, among which, the amorphous phases are identified for the first time.

25 ENERGY STORAGE↗
DOE OSTI2022

Enabling technologies for the continuous electrically driven conversion of CO 2 and water to multi-carbon products at high current densities

Here, we demonstrate greatly improved conversion of CO 2 using a gas diffusion electrode (GDE) with flowing electrolyte configuration for CO 2 gas delivery in combination with a high surface area nickel phosphide electrocatalyst. This configuration achieves 40–50% selectivity for total carbon products over H 2 formation (HER) at total current densities ranging from 50 to 300 mA cm -2 . We developed a soft-templating method using CTAB detergent micelles for synthesis of phase-pure Ni 2 P, achieving a 260-fold larger surface area (BET) and porous sponge-like morphology that produces stable currents. This catalyst produces mainly one C-product, methylglyoxal (MG, C 3 H 4 O 2 ) with 38–47% overall selectivity, the highest reported selectivity for a 12-electron reduction product. The versatile soft-templating method for electrocatalyst synthesis uses low-temperature (185 °C) that is permissive for incorporation of co-catalysts that are otherwise destroyed by the high temperatures used in traditional solid-state synthesis (SSS). The non-porous Ni 2 P-SSS catalyst produces mainly H 2 at these current densities. Achieving these high currents and C/H selectivity benefits from use of hydrophobic polymers as co-catalyst binders (cationic = Nafion, anionic = PFAEM and neutral = PTFE) to improve CO 2 conversion. PFAEM is the better ionomer for the CO 2 RR at high current density, postulated as due to suppressing CO 2 conversion to inactive bicarbonate. Precipitation of the carbon products as a polycarbonate polymer occurs at high currents.

36 MATERIALS SCIENCE↗