Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “packing density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

Evolution of surface stress during oxygen exposure of clean Si(111), Si(100), and amorphous Si surfaces

The evolutions of the surface stress of Si(111)-7 × 7, Si(100)-2 × 1, and a-Si surfaces upon oxygen exposure at pO{sub 2} = 1 × 10{sup −4} Pa and room temperature have been investigated in a comparative manner using a specimen-curvature based technique. To this end, a generally applicable, dedicated set of experiments has been devised and performed to deduce and correct for the surface stress change owing to oxygen reaction(s) at the (poorly-defined) back face of the specimen only. On this basis, it could be demonstrated that exposure of clean Si(111)-7 × 7, Si(100)-2 × 1 and a-Si surfaces to pure oxygen gas results in compressive surface stress changes for all three surfaces due to the incorporation of oxygen into Si backbonds. The measured surface stress change decreases with decreasing atomic packing density at the clean Si surfaces, which complies well with the less-densily packed Si surface regions containing more free volume for the accommodation of adsorbed O atoms.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1976

Design automation for complex CMOS/SOS LSI hybrid substrates

A design automated approach used to develop thick-film hybrid packages is described. The hybrid packages produced combine thick-film and silicon on sapphire (SOS) laser surface interaction technologies to bring the on-chip performance level of SOS to the subsystem level. Packing densities are improved by a factor of eight over ceramic dual in-line packing; interchip wiring capacitance is low. Due to significant time savings, the design automated approach presented can be expected to yield a 3:1 reduction in cost over the use of manual methods for the initial design of a hybrid.

Ramondetta, P. W.↗
DOE OSTI2019

The Effect of Ring Expansion in Thienobenzo[ b ]indacenodithiophene Polymers for Organic Field-Effect Transistors

A fused donor, thienobenzo[b]indacenodithiophene (TBIDT), was designed and synthesized using a novel acid-promoted cascade ring closure strategy, and then copolymerized with a benzothiadiazole (BT) monomer. The backbone of TBIDT is an expansion of the well-known indacenodithiophene (IDT) unit and was expected to enhance the charge carrier mobility by improving backbone planarity and facilitating short contacts between polymer chains. However, the optimized field-effect transistors demonstrated an average saturation hole mobility of 0.9 cm 2 V -1 s -1 , lower than the performance of IDT-BT (~1.5 cm 2 V -1 s -1 ). Mobilities extracted from time-resolved microwave conductivity measurements were consistent with the trend in hole mobilities in organic field-effect transistor devices. Scanning tunneling microscopy measurements and computational modeling illustrated that TBIDT-BT exhibits a less ordered microstructure in comparison to IDT-BT. This reveals that a regular side-chain packing density, independent of conformational isomers, is critical to avoid local free volume due to irregular packing, which can host trapping impurities. DFT calculations indicated that TBIDT-BT, despite containing a larger, planar unit, showed less stabilization of planar backbone geometries in comparison to IDT-BT. This is due to the reduced electrostatic stabilizing interactions between the peripheral thiophene of the fused core and the BT unit, resulting in a reduction of the barrier to rotation around the single bond. Finally, these insights provide a greater understanding of the general structure-property relationships required for semiconducting polymer repeat units to ensure optimal backbone planarization, as illustrated with IDT-type units, guiding the design of novel semiconducting polymers with extended fused backbones for high-performance field-effect transistors.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Surfactant Facilitated Spreading of Aqueous Drops on Hydrophobic Surfaces

Microgravity technologies often require aqueous phases to spread over nonwetting hydrophobic solid surfaces. Surfactants facilitate the wetting of water on hydrophobic surfaces by adsorbing on the water/air and hydrophobic solid/water interfaces and lowering the surface tensions of these interfaces. The tension reductions decrease the contact angle, which increases the equilibrium wetted area. Hydrocarbon surfactants; (i.e., amphiphiles with a hydrophobic moiety consisting of an extended chain of (aliphatic) methylene -CH2- groups attached to a large polar group to give aqueous solubility) are capable of reducing the contact angles on surfaces which are not very hydrophobic, but do not reduce significantly the contact angles of the very hydrophobic surfaces such as parafilm, polyethylene or self assembled monolayers. Trisiloxane surfactants (amphiphiles with a hydrophobe consisting of methyl groups linked to a trisiloxane backbone in the form of a disk ((CH3)3-Si-O-Si-O-Si(CH3)3) and an extended ethoxylate (-(OCH2CH2)a-) polar group in the form of a chain with four or eight units) can significantly reduce the contact angle of water on a very hydrophobic surface and cause rapid and complete (or nearly complete) spreading (termed superspreading). The overall goal of the research described in this proposal is to establish and verify a theory for how trisiloxanes cause superspreading, and then use this knowledge as a guide to developing more general hydrocarbon based surfactant systems which superspread. We propose that the trisiloxane surfactants superspread because their structure allows them to strongly lower the high hydrophobic solid/aqueous tension when they adsorb to the solid surface. When the siloxane adsorbs, the hydrophobic disk parts of the molecule adsorb onto the surface removing the surface water. Since the cross-sectional area of the disk is larger than that of the extended ethoxylate chain, the disks can form a space-filling mat on the surface which removes a significant amount of the surface water. In this presentation, we report the results of measurements of the molecular packing and rates of kinetic exchange of the trisiloxane surfactants at the air/water interface in order to confirm our picture of trisiloxane packing, and provide additional insight into the superspreading process. We used the pendant bubble technique as a Langmuir trough to measure the trisiloxane equation of state which relates the tension to the surface concentration. From these measurements we obtain accurate values for the maximum packing density. We find that trisiloxanes with 4 and 8 ethoxylate groups have the same maximum packing concentration, indicating that the maximum packing is controlled by the cross section of the head group. For trisiloxanes with larger than eight ethoxylates, the maximum packing increases with ethoxylate number, indicating that the disposition of the ethoxylate chain (i.e., its effective size) is controlling. This supports our picture of superspreading: The superspreading ability of trisiloxanes decreases considerably for trisiloxanes with larger than eight ethoxylates; the packing measurements indicate that for the higher ethoxylate number trisiloxanes, the compact nonpolar head groups are pushed apart by the ethoxylate chain. They leave spaces of surface water on adsorption and do not lower the solid tension as much as their lower chain analogues. Finally the report measurements of the dynamic tension reduction accompanying the adsorption of trisiloxanes onto an initially clean interface using the pendant bubble technique, and we obtain from these relaxations, the equation of state and a mass transfer model, the rate constants for kinetic exchange. We find that the rate constants for desorption of trisiloxanes are generally much slower than for analogous aliphatic polyethoxylate surfactants with identical ethoxylate chain lengths. When an aqueous drop of a superspreader solution is placed on a hydrophobic surface and begins to spread, the lower desorption rates allows the tension at the drop center to remain reduced relative to the tension of the expanding periphery, thus strengthening Marangoni forces which can assist the spreading. Marangoni forces can be especially significant in the case of superspreaders because their maximum equilibrium reduction in tension is several dynes/cm lower than for aliphatic surfactants.

Kumar, Nitin↗
DOE OSTI2021

Additive Lithography–Organic Monolayer Patterning Coupled with an Area-Selective Deposition

The combination of area-selective deposition (ASD) with a patternable organic monolayer provides a versatile additive lithography platform, enabling the generation of a variety of nanoscale feature geometries. Stearate hydroxamic acid self-assembled monolayers (SAMs) were patterned with extreme ultraviolet (λ = 13.5 nm) or electron beam irradiation and developed with ASD to achieve line space patterns as small as 50 nm. Density functional theory was employed to aid in the synthesis of hydroxamic acid derivatives with optimized packing density to enhance the imaging contrast and improve dose sensitivity. Near-edge X-ray absorption fine structure spectroscopy and infrared spectroscopy reveal that the imaging mechanism is based on improved deposition inhibition provided by the cross-linking of the SAM to produce a more effective barrier during a subsequent deposition step. With patterned substrates composed of coplanar copper lines and silicon spacers, hydroxamic acids selectively formed monolayers on the metal portions and could undergo a pattern-wise exposure followed by ASD in the first combination of a patternable monolayer with ASD. This material system presents an additional capability compared to traditional ASD approaches that generally reflect a starting patterned surface. Finally, this bottoms-up additive approach to lithography may be a viable alternative to subtractive nanoscale feature generation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Ultrastructure of Shewanella oneidensis MR-1 nanowires revealed by electron cryotomography

Significance Recent findings from in vivo fluorescence and immunolabeling measurements hinted at the possible role of outer membrane (OM) extensions as Shewanella oneidensis MR-1 nanowires. However, a detailed understanding of the architecture and electron transport mechanism along OM extensions was lacking. In this work, we report a unique setup for correlative light and electron microscopy of Shewanella OM extensions and demonstrate that they are chains of interconnected outer membrane vesicles with densities, consistent with periplasmic and OM cytochromes, distributed along their length. We propose, based on the packing density of cytochromes measured from electron cryotomograms, that the electron transport mechanism involves a combination of direct electron hopping and diffusion of electron carriers.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Maximum CO 2 diffusion inside leaves is limited by the scaling of cell size and genome size

Maintaining high rates of photosynthesis in leaves requires efficient movement of CO 2 from the atmosphere to the mesophyll cells inside the leaf where CO 2 is converted into sugar. CO 2 diffusion inside the leaf depends directly on the structure of the mesophyll cells and their surrounding airspace, which have been difficult to characterize because of their inherently three-dimensional organization. Yet faster CO 2 diffusion inside the leaf was probably critical in elevating rates of photosynthesis that occurred among angiosperm lineages. Here we characterize the three-dimensional surface area of the leaf mesophyll across vascular plants. We show that genome size determines the sizes and packing densities of cells in all leaf tissues and that smaller cells enable more mesophyll surface area to be packed into the leaf volume, facilitating higher CO 2 diffusion. Measurements and modelling revealed that the spongy mesophyll layer better facilitates gaseous phase diffusion while the palisade mesophyll layer better facilitates liquid-phase diffusion. Our results demonstrate that genome downsizing among the angiosperms was critical to restructuring the entire pathway of CO 2 diffusion into and through the leaf, maintaining high rates of CO 2 supply to the leaf mesophyll despite declining atmospheric CO 2 levels during the Cretaceous.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2018

Sn-MOF derived bimodal-distributed SnO2 nanosphere as a high performance anode of sodium ion batteries with high gravimetric and volumetric capacities

Highlights: • Sn-MOF is used to prepare a bimodal-distributed SnO{sub 2} nanosphere. • The SnO{sub 2} nanosphere reveals a high tap density of 2.42 g cm{sup −3}. • The SnO{sub 2} nanosphere exhibits both of high gravimetric and volumetric capacity. • Excellent performances relate to structural stability and high Na{sup +} diffusion rates. - Abstract: This paper reported a high tap density SnO{sub 2} nanosphere with bimodal sizes distribution, which derived from Sn-based metal-organic frameworks (Sn-MOF) precursors. When used as anodes for Na-ion batteries, the SnO{sub 2} nanosphere was demonstrated with a high reversible sodium storage capacity of 417 mAh g{sup −1} at a current density of 50 mA g{sup −1} after 100 cycles. Even at a high current density of 1200 mA g{sup −1}, a reversible capacity of 105 mAh g{sup −1} can be obtained. Additionally, regarding to the packed volumetric capacity, the SnO{sub 2} nanosphere electrode demonstrated a high value of around 970 mAh cm{sup −3}, can be considered as a high volumetric capacity anode material. The excellent electrochemical performance could be ascribed to aspects of structural stability, high packing density and high Na{sup +} diffusion rates of the SnO{sub 2} nanosphere electrode. This work provides a new pathway to prepared nanostructured SnO{sub 2} materials, and demonstrated a high performance anode material for Na-ion battery with great specific capacity and cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2019

Saturated random packing built of arbitrary polygons under random sequential adsorption protocol

Random packings and their properties are a popular and active field of research. Numerical algorithms that can efficiently generate them are useful tools in their study. This paper focuses on random packings produced according to the random sequential adsorption (RSA) protocol. Developing the idea presented by G. Zhang, where saturated random packings built of regular polygons were studied, we create an algorithm that generates strictly saturated packings built of any polygons. Then, the algorithm was used to determine the packing fractions for arbitrary triangles. In this work, the highest mean packing density, 0.552 814 ± 0.000 063, was observed for triangles of side lengths 0.63 : 1 : 1. Additionally, microstructural properties of such packings, kinetics of their growth, as well as distributions of saturated packing fractions and the number of RSA iterations needed to reach saturation were analyzed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Binder Jet Additive Manufacturing of Silicon Carbide Solar Reactor (CRADA Report)

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Binder jet additive manufacturing of silicon carbide solar reactor

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Increasing the density of passive photonic-integrated circuits via nanophotonic cloaking

Photonic-integrated devices need to be adequately spaced apart to prevent signal cross-talk. This fundamentally limits their packing density. Here we report the use of nanophotonic cloaking to render neighbouring devices invisible to one another, which allows them to be placed closer together than is otherwise feasible. Specifically, we experimentally demonstrated waveguides that are spaced by a distance of ~λ 0 /2 and designed waveguides with centre-to-centre spacing as small as 600 nm (<λ 0 /2.5). Our experiments show a transmission efficiency >–2 dB and an extinction ratio >15 dB over a bandwidth larger than 60 nm. This performance can be improved with better design algorithms and industry-standard lithography. The nanophotonic cloak relies on multiple guided-mode resonances, which render such devices very robust to fabrication errors. Our devices are broadly complimentary-metal-oxide-semiconductor compatible, have a minimum pitch of 200 nm and can be fabricated with a single lithography step. In conclusion, the nanophotonic cloaks can be generally applied to all passive integrated photonics.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Magnetic switching in granular FePt layers promoted by near-field laser enhancement

Light-matter interaction at the nanoscale in magnetic materials is a topic of intense research in view of potential applications in next-generation high-density magnetic recording. Laser-assisted switching provides a pathway for overcoming the material constraints of high-anisotropy and high-packing density media, though much about the dynamics of the switching process remains unexplored. We use ultrafast small-angle X-ray scattering at an X-ray free-electron laser to probe the magnetic switching dynamics of FePt nanoparticles embedded in a carbon matrix following excitation by an optical femtosecond laser pulse. We observe that the combination of laser excitation and applied static magnetic field, 1 order of magnitude smaller than the coercive field, can overcome the magnetic anisotropy barrier between “up” and “down” magnetization, enabling magnetization switching. This magnetic switching is found to be inhomogeneous throughout the material with some individual FePt nanoparticles neither switching nor demagnetizing. The origin of this behavior is identified as the near-field modification of the incident laser radiation around FePt nanoparticles. Furthermore, the fraction of not-switching nanoparticles is influenced by the heat flow between FePt and a heat-sink layer.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Final Report for contract DE-SC0010151, "A Cost-Effective Oxygen Separation System Based on Open Gradient Magnetic Field by Polymer Beads"

At present much of the oxygen enrichment market is based primarily on cryogenic systems, ion transport membranes made of ceramics, or polymer membranes technologies. All these methods have some positive and some negative attributes, but remain too expensive for the cost effective production of pure oxygen needed for clean renewable energy conversion projects. In a very successful Phase I period, the ITN-TAMU team accomplished the completion of most of the sub-tasks on oxygen separation based on our proposed magnetic field gradients. Theoretical and computer simulation data under different conditions of flow rates, magnetic flux, magnetic beads packing density, pressure and temperature have resulted very valuable observations. Chitosan based polymer magnetic beads showed the best results for uniformity and column packing. Due to limited magnetic force of 1 Tesla, we were restricted to use only single small column of magnetic beads and limited air pressure with controlled flow rate. We also fabricated smaller sized beads column with metal and clear plastic frames to be used for more concentrated packed capacity. Beads made with rare earth Neodymium were not uniform and were quite brittle. Different surfactants have minimized the effect of the de-aggregation of polymer magnetic beads. This Phase I development work also included overcoming key packaging hurdles such as high packing capacity of magnetic polymer beads and formation of consistent batch of magnetic beads. Market and commercialization studies were also initiated to show that there is a growing market for the proposed cost-effective oxygen separation system for energy conversion projects.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2019

Method of manufacturing high volumetric density electrodes from self-aligning fiber powders

An electrode and a related method of manufacture are provided. The electrode includes a self-aligning active material having short fiber powders with a cylindrical morphology to increase the packing density from 0.74 to nearly 0.91. The short fiber powders self-align during a slurring coating process as a result of shear forces between a die and a foil. The resulting coating includes parallel short fibers in a closed packed arrangement, providing an increased volumetric capacity of at least approximately 17%.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Heteroatom-Doped Porous Carbon Materials with Unprecedented High Volumetric Capacitive Performance

The design of carbon-based materials with a high mass density and large porosity has always been a challenging goal, since they fulfill the demands of next-generation supercapacitors and other electrochemical devices. We report a new class of high-density heteroatom-doped porous carbon that can be used as an aqueous-based supercapacitor material. The material was synthesized by an in situ dehalogenation reaction between a halogenated conjugated diene and nitrogen-containing nucleophiles. Under the given conditions, pyridinium salts can only continue to perform the dehalogenation if there is residue water remaining from the starting materials. The obtained carbon materials are highly doped by various heteroatoms, leading to high densities, abundant multimodal pores, and an excellent volumetric capacitive performance. Porous carbon tri-doped with nitrogen, phosphorous, and oxygen exhibits a high packing density (2.13 g cm -3 ) and an exceptional volumetric energy density (36.8 Wh L -1 ) in alkaline electrolytes, making it competitive to even some Ni-MH cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗