Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxygen stoichiometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

High-Performance Monopropellants and Catalysts Evaluated

The NASA Glenn Research Center is sponsoring efforts to develop advanced monopropellant technology. The focus has been on monopropellant formulations composed of an aqueous solution of hydroxylammonium nitrate (HAN) and a fuel component. HAN-based monopropellants do not have a toxic vapor and do not need the extraordinary procedures for storage, handling, and disposal required of hydrazine (N2H4). Generically, HAN-based monopropellants are denser and have lower freezing points than N2H4. The performance of HAN-based monopropellants depends on the selection of fuel, the HAN-to-fuel ratio, and the amount of water in the formulation. HAN-based monopropellants are not seen as a replacement for N2H4 per se, but rather as a propulsion option in their own right. For example, HAN-based monopropellants would prove beneficial to the orbit insertion of small, power-limited satellites because of this propellant's high performance (reduced system mass), high density (reduced system volume), and low freezing point (elimination of tank and line heaters). Under a Glenn-contracted effort, Aerojet Redmond Rocket Center conducted testing to provide the foundation for the development of monopropellant thrusters with an I(sub sp) goal of 250 sec. A modular, workhorse reactor (representative of a 1-lbf thruster) was used to evaluate HAN formulations with catalyst materials. Stoichiometric, oxygen-rich, and fuelrich formulations of HAN-methanol and HAN-tris(aminoethyl)amine trinitrate were tested to investigate the effects of stoichiometry on combustion behavior. Aerojet found that fuelrich formulations degrade the catalyst and reactor faster than oxygen-rich and stoichiometric formulations do. A HAN-methanol formulation with a theoretical Isp of 269 sec (designated HAN269MEO) was selected as the baseline. With a combustion efficiency of at least 93 percent demonstrated for HAN-based monopropellants, HAN269MEO will meet the I(sub sp) 250 sec goal.

Reed, Brian D.↗
DOE OSTI2020

The structural information filtered features (SIFF) potential: Maximizing information stored in machine-learning descriptors for materials prediction

Machine learning inspired potentials continue to improve the ability for predicting structures of materials. However, many challenges still exist, particularly when calculating structures of disordered systems. These challenges are primarily due to the rapidly increasing dimensionality of the feature-vector space which in most machine-learning algorithms is dependent on the size of the structure. In this article, we present a feature-engineered approach that establishes a set of principles for representing potentials of physical structures (crystals, molecules, and clusters) in a feature space rather than a physically motivated space. Our goal in this work is to define guiding principles that optimize information storage of the physical parameters within the feature representations. In this manner, we focus on keeping the dimensionality of the feature space independent of the number of atoms in the structure. Our Structural Information Filtered Features (SIFF) potential represents structures by utilizing a feature vector of low-correlated descriptors, which correspondingly maximizes information within the descriptor. We present results of our SIFF potential on datasets composed of disordered (carbon and carbon–oxygen) clusters, molecules with C 7 O 2 H 2 stoichiometry in the GDB9-14B dataset, and crystal structures of the form (Al x Ga y In z ) 2 O 3 as proposed in the NOMAD Kaggle competition. Our potential's performance is at least comparable, sometimes significantly more accurate, and often more efficient than other well-known machine-learning potentials for structure prediction. However, primarily, we offer a different perspective on how researchers should consider opportunities in maximizing information storage for features.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Control of Surface Chemical Reactions through Solid Stiffness

Control of surface reactions is commonly achieved by modification of surface electronic structures. Here, we discover an alternative pathway for controlling surface reactions by tuning the mechanical stiffness of the underlying material. We find that in addition to the typically assumed surface electronic contribution right at the reactive site, the contribution from the deformation of the bulk region plays a vital role in controlling surface reactions. The underlying mechanism is an elastic relaxation of the solid, which depends on the material’s stiffness and can be modified by tuning bulk stoichiometry. The effect of bulk stiffness on surface reactions has been demonstrated by considering hydrogen scission reaction and oxygen incorporation reaction during corrosion of amorphous SiC in water and air, respectively. Finally, our results imply that tuning of bulk stiffness by modifying stoichiometry can provide an effective method for controlling surface reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Application of machine learning to discover new intermetallic catalysts for the hydrogen evolution and the oxygen reduction reactions

The adsorption energies for hydrogen, oxygen, and hydroxyl were calculated by means of density functional theory on the lowest energy surface of 24 pure metals and 332 binary intermetallic compounds with stoichiometries AB, A 2 B, and A 3 B taking into account the effect of biaxial elastic strains. This information was used to train two random forest regression models, one for the hydrogen adsorption and another for the oxygen and hydroxyl adsorption, based on 9 descriptors that characterized the geometrical and chemical features of the adsorption site as well as the applied strain. All the descriptors for each compound in the models could be obtained from physico-chemical databases. The random forest models were used to predict the adsorption energy for hydrogen, oxygen, and hydroxyl of ≈2700 binary intermetallic compounds with stoichiometries AB, A 2 B, and A 3 B made of metallic elements, excluding those that were environmentally hazardous, radioactive, or toxic. This information was used to search for potential good catalysts for the HER and ORR from the criteria that their adsorption energy for H and O/OH, respectively, should be close to that of Pt. Further, this investigation shows that the suitably trained machine learning models can predict adsorption energies with an accuracy not far away from density functional theory calculations with minimum computational cost from descriptors that are readily available in physico-chemical databases for any compound. Moreover, the strategy presented in this paper can be easily extended to other compounds and catalytic reactions, and is expected to foster the use of ML methods in catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Precipitation of dopants on acceptor-doped LaMnO3±δ revealed by defect chemistry from first principles

Perovskite oxides degrade at elevated temperatures while precipitating dopant-rich particles on the surface. A knowledge-based improvement of surface stability requires a fundamental and quantitative understanding of the dopant precipitation mechanism on these materials. We propose that dopant precipitation is a consequence of the variation of dopant solubility between calcination and operating conditions in solid oxide fuel cells (SOFCs) and electrolyzer cells (SOECs). To study dopant precipitation, we use 20% (D = Ca, Sr, Ba)-doped LaMnO3+δ (LDM20) as a model system. We employ a defect model taking input from density functional theory calculations. The defect model considers the equilibration of LDM20 with a reservoir consisting of dopant oxide (DO), peroxide (DO2), and O2 in the gas phase. The equilibrated non-stoichiometry of the A-site and B-site as a function of temperature, T, and oxygen partial pressure, p(O2), reveals three regimes for LDM20: A-site deficient (oxidizing conditions), A-site rich (atmospheric conditions), and near-stoichiometric (reducing conditions). Assuming an initial A/B non-stoichiometry, we compute the dopant precipitation boundaries in a p–T phase diagram. Our model predicts precipitation both under reducing (DO) and under highly oxidizing conditions (DO2). We found precipitation under anodic, SOEC conditions to be promoted by large dopant size, while under cathodic, SOFC conditions precipitation is promoted by initial A-site excess. The main driving forces for precipitation are oxygen uptake by the condensed phase under oxidizing conditions and oxygen release assisted by B-site vacancies under reducing conditions. Possible strategies for mitigating dopant precipitation under in electrolytic and fuel cell conditions are discussed.

Hess, Franziska (ORCID:000000024460643X)↗
NASA NTRS1991

Detonability of hydrocarbon fuels in air

Studies were conducted of the detonation of gas-phase mixtures of n-hexane and JP-4, with oxidizers as varied as air and pure oxygen, measuring detonation velocities and cell sizes as a function of stoichiometry and diluent concentration. The induction length of a one-dimensional Zeldovich-von Neumann-Doering detonation was calculated on the basis of a theoretical model that employed the reaction kinetics of the hydrocarbon fuels used. Critical energy and critical tube diameter are compared for a relative measure of the heavy hydrocarbon fuels studied; detonation sensitivity appears to increase slightly with increasing carbon number.

Beeson, H. D.↗
DOE OSTI2023

High‐Nickel Heterostructured Cathodes with Local Stoichiometry Control for High‐Voltage Operation

The growing demand for lithium‐ion batteries to power electric vehicles and other energy‐dense devices continues to fuel the need for cathodes of increasingly higher nickel in cathodes. The relentless pursuit of high Ni content, however, raises concerns on compromising cell lifetime and safety, especially under high‐voltage operation. Alternative to the traditional design of uniform or core–shell composition, we report a rational control of local stoichiometry in high‐Ni cathodes, enabling their high thermal and cycling stabilities—up to 258 °C at the fully charged state and 91.4% capacity retention for 100 cycles between 2.7 and 4.4 V. Multimodal synchrotron X‐ray characterization unveils the heterostructure of secondary particles, featuring a high‐Ni core (LiNi 0.90 Mn 0.05 Co 0.05 O 2 ) covered by a thin Ni‐gradient layer that remains stable over prolonged cycling due to suppressed oxygen release and structural deterioration. This work underlines, the intricate interplay between local stoichiometry and redox reactions in stabilizing high‐Ni cathodes for high‐voltage operation while ensuring safety.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Steam-Assisted Ammonolysis of MoO2 as a Synthetic Pathway to Oxygenated δ-MoN

A common route for the synthesis of molybdenum nitrides is through the temperature-programmed reaction of molybdenum oxides with NH3, or ammonolysis. In this work, the role of precursor phase, gas phase chemistry (impact of H2O), and temperature profile on the reaction outcome (700 °C) was examined, which resulted in varying amounts of MoO2, H2MoO5, and the nitride phases—cubic γ (nominally Mo2N) and hexagonal δ (nominally MoN). The phase fraction of the δ phase increased with precursor in the sequence MoO2 > MoO3 > H2MoO5. Steam in the reaction gas also favored the production of δ over γ, but with too much steam, MoO2 was obtained in the product. Synthesis conditions for obtaining nearly phase-pure δ were identified: MoO2 as the precursor, 2% H2O in the gas stream, and a moderate heating rate (3 °C/min). In situ X-ray diffraction provided insights into the reaction pathway. Extensive physico-chemical analysis of the δ phase, including synchrotron X-ray and neutron diffraction, electron microscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, and prompt gamma activation analysis, revealed its stoichiometry to be MoO0.108(8)N0.892(8)H0.012(5), indicating non-trivial oxygen incorporation. The presence of N/O ordering and an impurity phase Mo5N6 were also revealed, detectable only by neutron diffraction. Notably, a computationally predicted MoON phase (doi: 10.1103/PhysRevLett.123.236402), of interest due to its potential to display a metal-insulator transition, did not appear under any reaction condition examined.

Pandey, Shobhit↗
DOE OSTI2020

Dicarboxylic acid emissions from a GDI engine equipped with a catalytic gasoline particulate filter

Dicarboxylic acids play an important role in atmospheric chemistry, yet their emissions from primary sources, such as internal combustion engines, has not been extensively studied. In this paper, KOH impregnated quartz filters were loaded with exhaust gases from a gasoline direct injection (GDI) engine equipped with a catalytic gasoline particulate filter (GPF). All filters were analyzed for carboxylic and dicarboxylic acids using a derivatized gas chromatography-mass spectroscopy method. Exhaust gas was sampled from pre-GPF and post-GPF locations to determine the performance of the GPF regarding acid conversion. Lean and stoichiometric engine modes were considered with non-oxygenated gasoline and 10% splash blended ethanol in gasoline (E10) to examine the impact of stoichiometry and fuel type. Acid emissions represented as much as 0.51% of total unburned hydrocarbon emissions for total monocarboxylic acids and as much as 0.40% for total dicarboxylic acids. Individual acid concentrations were as high as 38 mg/kg-fuel for monocarboxylic acids and as high as 29 mg/kg-fuel for dicarboxylic acids. Overall, the study found that fuel oxygenates had mixed impact on the acid emissions. Engine-out monocarboxylic acids were reduced when using the E10 fuel by approximately 30–45% for the stoichiometric condition and increased marginally for the lean condition. Dicarboxylic acid emissions were generally insensitive to ethanol content. However, the engine condition significantly affected the acid emissions. Lean operation produced a factor of two to an order of magnitude higher emissions rates of both monocarboxylic and dicarboxylic acids than the stoichiometric condition. The catalytic GPF eliminated between 80 and 92% of the acids emitted from the engine, allowing some acids to be emitted into the environment.

42 ENGINEERING↗
DOE OSTI2020

Local lattice distortions and dynamics in extremely overdoped superconducting YSr 2 Cu 2.75 Mo 0.25 O 7.54

A common characteristic of many “overdoped” cuprates prepared with high-pressure oxygen is T c values ≥ 50 K that often exceed that of optimally doped parent compounds, despite O stoichiometries that place the materials at the edge or outside of the conventional boundary between superconducting and normal Fermi liquid states. X-ray absorption fine-structure (XAFS) measurements at 52 K on samples of high-pressure oxygen (HPO) YSr 2 Cu 2.75 Mo 0.25 O 7.54 , T c = 84 K show that the Mo is in the (VI) valence in an unusually undistorted octahedral geometry with predominantly Mo neighbors that is consistent with its assigned substitution for Cu in the chain sites of the structure. Perturbations of the Cu environments are minimal, although the Cu X-ray absorption near-edge structure (XANES) differs from that in other cuprates. The primary deviation from the crystal structure is therefore nanophase separation into Mo- and Cu-enriched domains. There are, however, indications that the dynamical attributes of the structure are altered relative to YBa 2 Cu 3 O 7 , including a shift of the Cu-apical O two-site distribution from the chain to the plane Cu sites. Another effect that would influence T c is the possibility of multiple bands at the Fermi surface caused by the presence of the second phase and the lowering of the Fermi level.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1978

Application of ESCA to the determination of stoichiometry in sputtered coatings and interface regions

X-ray photoelectron spectroscopy was used to characterize radiofrequency sputter deposited films of several refractory compounds. Both the bulk film properties such as purity and stoichiometry and the character of the interfacial region between the film and substrate were examined. The materials were CrB2, MoS2, Mo2C, and Mo2B5 deposited on 440C steel. It was found that oxygen from the sputtering target was the primary impurity in all cases. Biasing improves the film purity. The effect of biasing on film stoichiometry is different for each compound. Comparison of the interfacial composition with friction data suggests that adhesion of these films is improved if a region of mixed film and iron oxides can be formed.

Wheeler, D. R.↗
NASA NTRS1978

Application of ESCA to the determination of stoichiometry in sputtered coatings and interface regions

X-ray Photoelectron Spectroscopy (XPS) was used to characterize radiofrequency sputter deposited films of several refractory compounds. Both the bulk film properties such as purity and stoichiometry and the character of the interfacial region between the film and substrate were examined. The materials were CrB2, MoS2, Mo2C, and Mo2B5 deposited on 440C steel. It was found that oxygen from the sputtering target was the primary impurity in all cases. Biasing improves the film purity. The effect of biasing on film stoichiometry is different for each compound. Comparison of the interfacial composition with friction data suggests that adhesion of these films is improved if a region of mixed film and iron oxides can be formed.

Wheeler, D. R.↗
DOE OSTI2022

Densification of the entropy stabilized oxide (Mg 0.2 Co 0.2 Ni 0.2 Cu 0.2 Zn 0.2 )O

The first entropy-stabilized oxide, (Mg 0.2 Co 0.2 Ni 0.2 Cu 0.2 Zn 0.2 )O, was reported in 2015. Initial studies synthesized this material using solid state processing and were limited to densities < 80%. Here, we report a straightforward solid state route to sinter samples to densities up to 98% of the theoretical by identifying the role of oxygen and promoting the resulting mechanisms in densification. Previous works have studied effects of cation stoichiometry on the entropy-driven reaction to form a single phase, but few have explored the associated effects of anion stoichiometry and/or redox chemistry on both phase stability and densification. We demonstrate here that tuning heating rate and pO 2 during heating of initially-homogeneous calcined powders can enhance densifying diffusion processes and enable reliable sintering of dense (Mg 0.2 Co 0.2 Ni 0.2 Cu 0.2 Zn 0.2 )O samples.

MATERIALS SCIENCE↗
DOE OSTI2026

Alkali-Metal Interlocking of 2D V 4 O 10 Sheets Defines Discretized Interlayer Shear Relationships

Low-dimensional materials manifest structural anisotropy, quantum confinement, and tightly bound excitonic states, which make them attractive building blocks that can be assembled within three-dimensional laterally stitched heterostructures, stacked van der Waals solids, and complex moiré superlattices. Ion intercalation in the galleries between layered materials provides a means of modifying interlayer separation and coupling, but it is also known to drive the shearing of the layers. In this article, we explore the distinct ligand coordination environments afforded by vanadyl oxygens of singular [V 4 O 10 ] sheets and examine how the size, polarizability, and stoichiometry of Group I cations sandwiched between such layers determine the interlocking of the sheets in stacked structures. Based on the topochemical insertion of alkali-metal ions into the layered λ-V 2 O 5 , we identify seven types of guest ion coordination sites discretized into four distinct regimes of interlayer shear in units of half octahedral widths. The coordination preferences of intercalated cations govern how they interlock 2D [V 4 O 10 ] sheets and engender specific shear conformations. We present evidence that static and dynamic disorder in guest ion arrangement modulate the magnetic structure of the intercalated compounds based on electrostatic polarization, localization of charge and spin density, and lattice distortion. The results illustrate the use of topochemical ion insertion to modulate stacking relationships and magnetic transition characteristics.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Off-design performance analysis of MHD generator channels

A computer code for performing parametric design point calculations, and evaluating the off-design performance of MHD generators has been developed. The program is capable of analyzing Faraday, Hall, and DCW channels, including the effect of electrical shorting in the gas boundary layers and coal slag layers. Direct integration of the electrode voltage drops is included. The program can be run in either the design or off-design mode. Details of the computer code, together with results of a study of the design and off-design performance of the proposed ETF MHD generator are presented. Design point variations of pre-heat and stoichiometry were analyzed. The off-design study included variations in mass flow rate and oxygen enrichment.

Wilson, D. R.↗
DOE OSTI2022

Overcoming significant challenges in extracting off-stoichiometric thermodynamics using the compound energy formalism through complementary use of experimental and first principles data: A case study of Ba 1-x Sr x FeO 3-δ

The compound energy formalism (CEF) is a powerful framework to describe the thermodynamics of metal oxides as a function of off-stoichiometry, temperature, and composition. The thermodynamic properties are crucial materials design attributes in metal oxide-based oxygen-exchange chemical processes. Despite the richness of information an accurate CEF model provides, a method to determine a unique and accurate fit for oxygen exchange materials remains elusive. This contribution details a method for fitting the CEF model that overcomes the current fitting challenges through three innovations: 1) the combination of density functional theory calculations with experimental data decorrelates excess terms and delineates the enthalpic/entropic contributions to the Gibbs free energy; 2) a systematic determination of the important CEF model terms, removing thermodynamic predetermining human intervention; 3) a self-consistent solution of the starting oxygen offstoichiometry (δ 0 ) of thermogravimetric measurements. Thus, our method enables the reliable extraction of off-stoichiometric metal oxide thermodynamic properties and facilitates rapid materials compositional screening, and reliable process design of systems dependent on off-stoichiometric redox-active metal oxides. We apply this method to a Ba x Sr 1-x FeO 3-δ test case. We find by systematically examining the performance of the CEF model fit with and without each innovation that all three innovations are necessary for an accurate fit. We determined that reduction enthalpy is higher and more sensitive to off-stoichiometry when the Sr fraction is large (139.5 and 185.3 kJ/mol O 2 for SrFeO 3 at δ = 0 and δ = 0.5, respectively vs. nearly constant 83 kJ/mol O 2 for BaFeO 3 ). However, the reduction entropy is mostly insensitive to Sr fraction, but highly dependent on δ suggesting larger contributions in the non-configurational entropy parameters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Molecular beam epitaxy of PdO on MgO (001)

PdO, widely used in catalysis in powder form for decades, has been predicted recently to be a Dirac semimetal. Synthesis of high-quality single crystals of this material is thus of great interest. Here, by using ozone-assisted molecular beam epitaxy, PdO thin films were grown on a MgO (001) substrate. X-ray diffraction and transmission electron microscopy indicate the film is a / b axis oriented, with the c axis lying in plane. Fully oxygenated PdO films have a low density of holelike carriers, and are insulating at the lowest temperatures. Our density functional theory calculations using the Heyd-Scuseria-Ernzerhof exchange-correlation functional suggest a ~1.0 eV band gap at the M point, where the gap can be reduced by tensile strain along the c axis and the bands begin to invert when the tensile strain is as high as 18%. Although tensile strain of this magnitude is experimentally not viable using epitaxy, electrons can be doped by oxygen reduction. Finally, our results emphasize the need for careful consideration of electron correlation effects and stoichiometry in ab initio modeling of topological semimetals involving transition metal oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Freestanding epitaxial SrTiO 3 nanomembranes via remote epitaxy using hybrid molecular beam epitaxy

The epitaxial growth of functional oxides using a substrate with a graphene layer is a highly desirable method for improving structural quality and obtaining freestanding epitaxial nanomembranes for scientific study, applications, and economical reuse of substrates. However, the aggressive oxidizing conditions typically used in growing epitaxial oxides can damage graphene. Here, we demonstrate the successful use of hybrid molecular beam epitaxy for SrTiO 3 growth that does not require an independent oxygen source, thus avoiding graphene damage. This approach produces epitaxial films with self-regulating cation stoichiometry. Furthermore, the film (46-nm-thick SrTiO 3 ) can be exfoliated and transferred to foreign substrates. These results open the door to future studies of previously unattainable freestanding oxide nanomembranes grown in an adsorption-controlled manner by hybrid molecular beam epitaxy. This approach has potentially important implications for the commercial application of perovskite oxides in flexible electronics and as a dielectric in van der Waals thin-film electronics.

36 MATERIALS SCIENCE↗