Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “outdoor lighting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

CO2 MONITORING FOR DEMAND CONTROLLED VENTILATION IN COMMERCIAL BUILDINGS

Carbon dioxide (CO{sub 2}) sensors are often deployed in commercial buildings to obtain CO{sub 2} data that are used, in a process called demand-controlled ventilation, to automatically modulate rates of outdoor air ventilation. The objective is to keep ventilation rates at or above design specifications and code requirements and also to save energy by avoiding excessive ventilation rates. Demand controlled ventilation is most often used in spaces with highly variable and sometime dense occupancy. Reasonably accurate CO{sub 2} measurements are needed for successful demand controlled ventilation; however, prior research has suggested substantial measurement errors. Accordingly, this study evaluated: (a) the accuracy of 208 CO{sub 2} single-location sensors located in 34 commercial buildings, (b) the accuracy of four multi-location CO{sub 2} measurement systems that utilize tubing, valves, and pumps to measure at multiple locations with single CO{sub 2} sensors, and (c) the spatial variability of CO{sub 2} concentrations within meeting rooms. The field studies of the accuracy of single-location CO{sub 2} sensors included multi-concentration calibration checks of 90 sensors in which sensor accuracy was checked at multiple CO{sub 2} concentrations using primary standard calibration gases. From these evaluations, average errors were small, -26 ppm and -9 ppm at 760 and 1010 ppm, respectively; however, the averages of the absolute values of error were 118 ppm (16%) and 138 ppm (14%), at concentrations of 760 and 1010 ppm, respectively. The calibration data are generally well fit by a straight line as indicated by high values of R{sup 2}. The Title 24 standard specifies that sensor error must be certified as no greater than 75 ppm for a period of five years after sensor installation. At 1010 ppm, 40% of sensors had errors greater than {+-}75 ppm and 31% of sensors has errors greater than {+-}100 ppm. At 760 ppm, 47% of sensors had errors greater than {+-}75 ppm and 37% of sensors had errors greater than {+-}100 ppm. A significant fraction of sensors had errors substantially larger than 100 ppm. For example, at 1010 ppm, 19% of sensors had an error greater than 200 ppm and 13% of sensors had errors greater than 300 ppm. The field studies also included single-concentration calibration checks of 118 sensors at the concentrations encountered in the buildings, which were normally less than 500 ppm during the testing. For analyses, these data were combined with data from the calibration challenges at 510 ppm obtained during the multi-concentration calibration checks. For the resulting data set, the average error was 60 ppm and the average of the absolute value of error was 154 ppm. Statistical analyses indicated that there were statistically significant differences between the average accuracies of sensors from different manufacturers. Sensors with a 'single lamp single wavelength' design tended to have a statistically significantly smaller average error than sensors with other designs except for 'single lamp dual wavelength' sensors, which did not have a statistically significantly lower accuracy. Sensor age was not consistently a statistically significant predictor of error.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Evaluating efficacy of different UV-stabilizers/absorbers in reducing UV-degradation of lignin

Abstract Susceptibility of wood to UV degradation decreases the service life of wood products outdoors. Organic UV absorbers (UVAs) and hindered amine light stabilizers (HALSs), as well as inorganic UVAs, are added to coatings to improve the UV stability of coated-wood products. Although about 85% of UV radiation is absorbed by lignin in the wood, it is unclear which UV stabilizers can minimize lignin degradation. In this study, the photodegradation of softwood organosolv lignin was monitored over 35 days of UV exposure. Changes in lignin properties were assessed using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), and phosphorus-31 nuclear magnetic resonance spectroscopy ( 31 P NMR). It was found that the aromatic rings of lignin underwent significant degradation, resulting in increased glass transition temperature and molecular weight of lignin. Subsequently, 18 different additives were mixed with lignin and exposed to UV irradiation. The analysis of samples before and after UV exposure with FTIR revealed that inorganic UVAs (cerium oxide and zinc oxide) and a mixture of organic UVAs and HALSs (T-479/T-292, T-5248, and T-5333) were the most effective additives in reducing lignin degradation. This study can help coating scientists to formulate more durable transparent exterior wood coatings.

36 MATERIALS SCIENCE↗

Multifunctional Integrated Sensors (MFISES)

Many emerging IoT applications require sensing of multiple physical and environmental parameters for: completeness of information, measurement validation, unexpected demands, improved performance. For example, a typical outdoor weather station measures temperature, humidity, barometric pressure, light intensity, rainfall, wind speed and direction. Existing sensor technologies do not directly address the demand for cost, size, and power reduction in multi-paramater sensing applications. Industry sensor manufacturers have developed integrated sensor systems for inertial measurements that combine accelerometers, gyroscopes, and magnetometers, but do not address environmental sensing functionality. In existing research literature, a technology gap exists between the functionality of MEMS sensors and the real world applications of the sensors systems.

42 ENGINEERING↗

Domestication of Algae for Increasing Biomass Productivity

Microalgae cultivation processes have been developed for the production of a variety of bioproducts, however currently only a few species are used in commercial applications. Their domestication, that is strain improvements, is still in its infancy, with major advances required, specifically to maximize biomass productivity a limiting factor in microalgae production. This requires a deep understanding of algal biology, in particular to develop superior strains without the need of genetic technologies that would require lengthy regulatory permits, and often limit consumer acceptance. Adaptive Laboratory Evolution techniques, alone or in conjunction with sexual recombination, can allow for rapid develop of improved strains and their industrial production. Light harvesting antenna reduction has been a major approach to achieve increased photon utilization efficiency by cultures operating under full sunlight conditions due to higher light saturation levels, allowing for higher productivities under outdoor conditions. Decades of research yielded some promising results under controlled conditions with a few specific mutant strains. However, these failed to achieve the anticipated higher productivities in actual algal mass cultures, in part due to the inability of single mutations to overcome photoinhibition, reactive oxygen species, and other pleiotropic impacts on the complex metabolic processes of photosynthesis. Higher productivity strains will require multiple genetic improvements. We report on recent Adaptive Laboratory Evolution with the green alga Scenedesmus obliquus resulting in higher biomass productivity in open pond cultivation. Coupling our approach with sexual recombination and genome sequencing provides a path to algal domestication suitable for large-scale, low-cost biomass production.

09 BIOMASS FUELS↗

Domesticating the green alga Scenedesmus obliquus

Microalgae cultivation processes exist only for a few species used in commercial applications. Their domestication is still in its infancy, with major advances required, specifically to overcome limiting factors in microalgae production. The goal is to develop superior strains without the need of genetic technologies that would require lengthy regulatory permits, and often limit consumer acceptance. Adaptive Laboratory Evolution techniques, alone or in conjunction with sexual recombination, can allow for rapid develop of improved strains and their industrial production. Approaches include increased photon utilization efficiency by cultures operating under full sunlight conditions due to higher light saturation levels, allowing for higher productivities under outdoor conditions. Decades of research yielded some promising results under controlled conditions with a few specific mutant strains. However, these failed to achieve the anticipated higher productivities in actual algal mass cultures, in part due to the inability of mutations to overcome photoinhibition, reactive oxygen species, and other pleiotropic impacts on photosynthesis.

09 BIOMASS FUELS↗

Estimating the Maximum Achievable Productivity in Outdoor Ponds: Microalgae Biomass Growth Modeling and Climate Simulated Culturing

To address the challenge of determining the maximum achievable monthly, seasonal, and annual biomass productivity for selected promising strains in outdoor ponds at any geographic location of interest, we developed the following four step integrated strategy. First, the strain is characterized in terms of its specific growth rate response to temperature and light, including darkness, as well as its light attenuation characteristics. Second, these species-specific parameters serve as inputs to PNNL’s biomass growth model that, in conjunction with the sunlight and pond water temperature predictions provided by PNNL’s Biomass Assessment Tool, is used to predict the respective biomass productivities for tens of thousands of hypothetical pond locations in the United States. Third, monthly and annual biomass productivity maps are created to identify the geographic location(s) of optimum biomass productivity and to generate light and water temperature “scripts” (time series) for hypothetical ponds at the best site(s). Finally, the maximum achievable biomass productivity for the given strain is confirmed by conducting culture experiments in PNNL’s indoor LED-lighted and temperature-controlled ponds under climate-simulated conditions, using the previously determined light and temperature scripts. This integrated strategy provides an efficient and low risk approach to screen promising strains for their potential to exhibit high biomass productivities, and to validate their model-predicted performance in climate-simulation ponds before transitioning to cultivation in outdoor raceways.

biomass assessment tool↗

Incorporation of salinity, nitrogen, and shading stress factors into the Huesemann Algae Biomass Growth model

The Huesemann Algae Biomass Growth (HABG) model predicts microalgae biomass growth in outdoor raceways as a function of water temperature and incident light intensity. The model over-predicted growth in several Regional Algal Feedstock Testbed (RAFT) experiments. Inspection of the culture conditions suggested that salinity stress, nutrient limitation, and shading reduced growth, which were not included in the original model. Laboratory experiments were carried out to measure growth response of S. obliquus to high salinity and limited nitrogen. In addition, the shading effect was estimated based on raceway geometry, solar angle, albedo and measured light intensity data. In this study, the improvement of model performance is presented step by step as each growth limiting factor is incorporated into the model. The new salinity, shanding, and nutrient stress factors remove most of the over-prediction of the original model. Comparison of the model with observed data indicated that ignoring the lag phase also resulted in overprediction. Delaying the start of the simulation until the end of the lag phase and inclusion of stress factors lowered model inaccuracy from 90% over-prediction to within ±10% in six out of seven batches.

09 BIOMASS FUELS↗

Optimized Illuminance Operation-A Light-Driven Dilution Strategy to Improve Microalgae Biomass Productivity

Periodic dilution is a necessary operation to avoid light limitation due to self-shading as the culture grows dense. However, environmental conditions are constantly changing in outdoor cultivation systems, making it difficult to determine the optimal dilution rate. To address this challenge, this study evaluated a dilution approach based on light penetration to optimize illuminance (OptiLum) in the culture. Biomass concentration was controlled via sensor-feedback directed dilution to ensure that light reaching the bottom of the culture was maintained above the compensation intensity. Under replicated outdoor pond conditions, by keeping the entire culture within a net-positive photosynthetic zone, the OptiLum operation improved the biomass productivities of two top-performing strains, Picochlorum celeri and Tetraselmis striata, by 95 % and 86 %, respectively, compared to conventional semi-continuous batch cultivation. The dilution rate varied daily and was dynamically adjusted based on the light status within the culture, which is concurrently influenced by weather, culture density, and growth rate. The techno-economic analysis showed that the OptiLum operation could reduce biomass production cost by as much as 24 % and 33 % for P. celeri and T. striata, respectively, assuming a low-cost dewatering approach with initial gravity settling of biomass can be realized for both strains. However, a more costly two-stage dewatering strategy, comprising only membranes and centrifuges, may be necessary for non-settling strains, such as P. celeri, which would alternatively increase production costs by 23 % for the OptiLum case. The results demonstrated that the proposed OptiLum operation is a promising approach to improve biomass productivity and lower production cost via weather-responsive and self-adjusting dilution.

09 BIOMASS FUELS↗

Metastable Electrical Characteristics of Polycrystalline Thin-Film Photovoltaic Modules upon Exposure and Stabilization: Preprint

The significant features of a series of stabilization experiments conducted at the National Renewable Energy Laboratory (NREL) between May 2009 and the present are reported. These experiments evaluated a procedure to stabilize the measured performance of thin-film polycrystalline cadmium telluride (CdTe) and copper indium gallium diselenide (CIGS) thin-film photovoltaic (PV) modules. Thecurrent-voltage (I-V) characteristics of CdTe and CIGS thin-film PV devices and modules exhibit transitory changes in electrical performance after thermal exposure in the dark and/or bias and light exposures. We present the results of our case studies of module performance versus exposure: light-soaked at 65 degrees C; exposed in the dark under forward bias at 65 degrees C; and, finally,longer-term outdoor exposure. We find that stabilization can be achieved to varying degrees using either light-soaking or dark bias methods and that the existing IEC 61646 light-soaking interval may be appropriate for CdTe and CIGS modules with one caveat: it is likely that at least three exposure intervals are required for stabilization.

14 SOLAR ENERGY↗

The Energy and Operational Impacts of Using 0-10V Control for LED Streetlights

LED lighting is becoming widely adopted and displacing most traditional lighting technologies. However, the traditional methods used to control light sources have not seen similar displacement. Lighting systems have historically utilized either a proprietary control method, or one of a handful of standardized methods (e.g., 0-10V, DALI, DMX512). The utility and market success of the standardized methods has been limited for a variety of reasons. Analog 0-10V methods have long been popular due to their simplicity and low cost of implementation and are presently the most commonly available control interface for indoor and outdoor LED products in North America. The emergence of “connected lighting systems” with more modern network interfaces and luminaire-level sensors and intelligence was anticipated by many to mark the beginning of the end of analog control. However, 0-10V interfaces continue to be prevalent with these more “digital” systems. The use of 0-10V methods has significant tradeoffs. 0-10V standards have historically not explicitly defined the relationship between the luminaire input control signal and output luminous flux for the full control signal range. As a result, it is difficult to predict relative luminaire light output and input power at any particular control voltage, and in practice the performance across LED drivers and the luminaires power is inconsistent. While this inconsistency has long been acknowledged by experts in the field, it is not accounted for in standard practice deployment, and end-users continue to regularly see unexpected and undesirable performance. It is hoped that the results from this study will help the lighting industry and standards developing organizations better understand and possibly resolve the shortcomings of 0-10V products, and consider what is best for the industry – additional incremental improvements to this fundamentally limited analog technology, or fully moving on to existing digital approaches, such as DALI D4i, that deliver accurate and consistent dimming performance across all luminaires in the system and thus guarantee the delivery of expected light levels, and energy and cost savings. Recommendations consistent with these goals are made to lighting and driver manufacturers, lighting software developers, standard developing organizations, and system designers and specifiers.

0-10V↗

Meta‐Analysis and Regression Modeling of the Impacts of Four Indoor Environmental Quality Metrics on Office Performance

Awareness of how buildings interact with the occupant experience—especially human performance—is becoming more prevalent, as seen by increasing interest and investment in healthy built environments. However, there is a need to synthesize the wide array of existing indoor environmental assessment and performance research in a way that can translate directly to building design and operation. Existing research in this area typically focuses on a single isolated metric and has not focused on making the results utilizable by building practitioners. The aim of this research is to investigate existing office performance literature through meta‐analyses and produce regression models for four indoor environmental quality (IEQ) metrics to support critical decision‐making for building operation and renovation. To reach this aim, a literature review was conducted to identify studies that measure the impact of changing ventilation rate, temperature, horizontal illuminance, and noise level in offices on occupant task performance. This repository of field and laboratory studies was analyzed to visualize the trends between the selected IEQ metrics and task performance. The temperature, ventilation rate, and horizontal illuminance regression models showed clear improvement potential when modifying indoor conditions toward the defined high‐performance range, while the regression model for noise level was inconclusive. The discussion notes the importance of designing holistically for all components of these IEQ categories to utilize the results, for example, good filtration on outdoor air for quantifying ventilation impact and uniform overhead lighting with low contrast for quantifying horizontal illuminance impact. The novelty of this work is in considering multiple facets of the indoor environment under a single, unified analysis schema and producing IEQ‐based performance gains that can directly inform cost‐benefit analyses of building design and renovation.

60 APPLIED LIFE SCIENCES↗

Can Reflector Panel Technologies Tame Terrible Lunar Lighting Environments?

This project investigated the usage of reflector panel technology to redirect collimated sunlight to make it more usable for the lunar surface EVAs. When astronauts travel to the Moon’s South Pole, they will find a terrible exterior work environment to carry out EVA tasks. The location creates a situation where collimated light from the Sun illuminates the surface at low inclination angles, and the problem that the crew will often shadow their own workspace. Artificial lighting countermeasures will be marginally beneficial because the Sun’s illumination level is orders of magnitude higher than intensities possible from battery driven lighting systems. These conditions will persist because the latitude of the polar worksite, and the Moon’s orbit around the Earth. Photographers, on Earth, battle similar problems in their studios and outdoor worksites. To solve this problem, they use large portable reflectors to redirect light towards the object they are imaging.

Toni Anne Clark↗

Temperature-Sensitive Coating Sensor Based on Hematite

A temperature-sensitive coating, based on hematite (iron III oxide), has been developed to measure surface temperature using spectral techniques. The hematite powder is added to a binder that allows the mixture to be painted on the surface of a test specimen. The coating dynamically changes its relative spectral makeup or color with changes in temperature. The color changes from a reddish-brown appearance at room temperature (25 C) to a black-gray appearance at temperatures around 600 C. The color change is reversible and repeatable with temperature cycling from low to high and back to low temperatures. Detection of the spectral changes can be recorded by different sensors, including spectrometers, photodiodes, and cameras. Using a-priori information obtained through calibration experiments in known thermal environments, the color change can then be calibrated to yield accurate quantitative temperature information. Temperature information can be obtained at a point, or over an entire surface, depending on the type of equipment used for data acquisition. Because this innovation uses spectrophotometry principles of operation, rather than the current methods, which use photoluminescence principles, white light can be used for illumination rather than high-intensity short wavelength excitation. The generation of high-intensity white (or potentially filtered long wavelength light) is much easier, and is used more prevalently for photography and video technologies. In outdoor tests, the Sun can be used for short durations as an illumination source as long as the amplitude remains relatively constant. The reflected light is also much higher in intensity than the emitted light from the inefficient current methods. Having a much brighter surface allows a wider array of detection schemes and devices. Because color change is the principle of operation, the development of high-quality, lower-cost digital cameras can be used for detection, as opposed to the high-cost imagers needed for intensity measurements with the current methods. Alternative methods of detection are possible to increase the measurement sensitivity. For example, a monochrome camera can be used with an appropriate filter and a radiometric measurement of normalized intensity change that is proportional to the change coating temperature. Using different spectral regions yields different sensitivities and calibration curves for converting intensity change to temperature units. Alternatively, using a color camera, a ratio of the standard red, green, and blue outputs can be used as a self-referenced change. The blue region (less than 500 nm) does not change nearly as much as the red region (greater than 575 nm), so a ratio of color intensities will yield a calibrated temperature image. The new temperature sensor coating is easy to apply, is inexpensive, can contour complex shape surfaces, and can be a global surface measurement system based on spectrophotometry. The color change, or relative intensity change, at different colors makes the optical detection under white light illumination, and associated interpretation, much easier to measure and interpret than in the detection systems of the current methods.

Bencic, Timothy J.↗

Intraday Outdoor Efficiency Changes in Metal-Halide Perovskite Photovoltaic Modules

Here, we present outdoor observations of metal-halide perovskite modules deployed in the Photovoltaic Accelerator for Commercializing Technologies center, which houses one of the world's broadest efforts to test metal-halide perovskite photovoltaic modules outdoors. As of January 2025, outdoor testing has encompassed over 150 modules from 14 different partners. Our findings illustrate how daily changes in efficiency, driven by exposure to light, affect field performance in real-world conditions. These effects cannot be explained by existing outdoor performance models and frustrate the notion of a traditional temperature coefficient.

14 SOLAR ENERGY↗

Reliability of solid-state lighting electrical drivers subjected to WHTOL accelerated aging

An investigation of a solid-state lighting (SSL) luminaire with the focus on the electronic driver which has been exposed to a standard wet hot temperature operating life (WHTOL) of 85% RH and 85°C in order to assess reliability of prolonged exposer to a harsh environment has been conducted. SSL luminaires are beginning introduced as head lamps in some of today's luxury automobiles and may also be fulfilling a variety of important outdoor applications such as overhead street lamps, traffic signals and landscape lighting. SSL luminaires in these environments are almost certain to encounter excessive moisture from humidity and high temperatures for a persistent period of time. The lack of accelerated test methods for LEDs to assess long-term reliability prior to introduction into the marketplace, a need for SSL physics based PHM modeling indicators for assessment and prediction of LED life, as well as the U.S. Department of Energy's R&D roadmap to replace todays lighting with SSL luminaires makes it important to increase the understanding of the reliability of SSL devices, specifically, in harsh environment applications. In this work, a set of SSL electrical drivers were investigated to determine failure mechanisms that occur during prolonged harsh environment applications. Each driver consists of four aluminum electrolytic capacitors (AECs) of three different types and was considered the weakest component inside the SSL electrical driver. The reliability of the electrical driver was assessed by monitoring the change in capacitance and the change in equivalent series resistance for each AEC, as well as monitoring the luminous flux of the SSL luminaire or the output of the electrical driver. The luminous flux of a pristine SSL electrical driver was also monitored in order to detect minute changes in the electrical drivers output and to aid in the investigation of the SSL luminaires reliability. The failure mechanisms of the electrical drivers have been determined and are presented in this paper.

42 ENGINEERING↗

Hybrid Composite Coatings for Durable and Efficient Solar Hydrogen Generation under Diverse Operating Conditions

Safe and practical solar-driven hydrogen generators must be capable of efficient and stable operation under diurnal cycling with full separation of gaseous H 2 and O 2 products. In this paper, a novel architecture that fulfills all of these requirements is presented. The approach is inherently scalable and provides versatility for operation under diverse electrolyte and lighting conditions. The concept is validated using a 1 cm 2 triple-junction photovoltaic cell with its illuminated photocathode protected by a composite coating comprising an organic encapsulant with an embedded catalytic support. The device is compatible with operation under conditions ranging from 1 M H 2 SO 4 to 1 M KOH, enabling flexibility in selection of semiconductor, electrolyte, membrane, and catalyst. Stable operation at a solar-to-hydrogen conversion efficiency of >10% is demonstrated under continuous operation, as well as under diurnal light cycling for at least 4 d, with simulated sunlight. Operational characteristics are validated by extended time outdoor testing. A membrane ensures products are separated, with nonexplosive gas streams generated for both alkaline and acidic systems. Finally, analysis of operational characteristics under different lighting conditions is enabled by comparison of a device model to experimental data.

14 SOLAR ENERGY↗

A mobile apparatus for solar collector testing

The design, construction, and operation of a mobile apparatus for solar collector testing (MASCOT) is described. The MASCOT is a self-contained test unit costing about $10,000 whose only external requirement for operation is electrical power and which is capable of testing two water-cooled flat-plate solar collectors simultaneously. The MASCOT is small enough and light enough to be transported to any geographical site for outdoor tests at the location of collector usage. It has been used in both indoor solar simulator tests and outdoor tests.

Hotchkiss, G. B.↗