SEARCH · Engineering Papers

Results for “microwaves”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS2011

Chromospheric Signatures of the Subdued Cycle 23/24 Solar Minimum in Microwaves

Coronal holes appear brighter than the quiet Sun in microwave images, with a brightness enhancement of 500 to 2000 K. The brightness enhancement corresponds to the upper chromosphere, where the plasma temperature is about 10000 K. We constructed a microwave butterfly diagram using the synoptic images obtained by the Nobeyama radio-heliograph (NoRH) showing the evolution of the polar and low latitude brightness temperature. While the polar brightness reveals the chromospheric conditions, the low latitude brightness is attributed to active regions in the corona. When we compared the microwave butterfly diagram with the magnetic butterfly diagram, we found a good correlation between the microwave brightness enhancement and the polar field strength. The microwave butterfly diagram covers part of solar cycle 22, whole of cycle 23, and part of cycle 24, thus enabling comparison between the cycle 23/24 and cycle 22/23 minima. The microwave brightness during the cycle 23/24 minimum was found to be lower than that during the cycle 22/23 minimum by approx.250 K. The reduced brightness temperature is consistent with the reduced polar field strength during the cycle 23/24 minimum seen in the magnetic butterfly diagram. We suggest that the microwave brightness at the solar poles is a good indicator of the speed of the solar wind sampled by Ulysses at high latitudes.

Yashiro, S.↗

NASA NTRS2011

Broadband Via-Less Microwave Crossover Using Microstrip-CPW Transitions

The front-to-back interface between microstrip and CPW (coplanar waveguide) typically requires complex fabrication or has high radiation loss. The microwave crossover typically requires a complex fabrication step. The prior art in microstrip-CPW transition requires a physical vias connection between the microstrip and CPW line on a separate layer. The via-less version of this transition was designed empirically and does not have a close form solution. The prior art of the micro wave crossover requires either additional substrate or wire bond as an air bridge to isolate two microwave lines at the crossing junction. The disadvantages are high radiation loss, no analytical solution to the problem, lengthy simulation time, and complex fabrication procedures to generate air bridges or via. The disadvantage of the prior crossover is a complex fabrication procedure, which also affects the device reliability and yield. This microstrip-CPW transition is visualized as two microstrip-slotline transitions combined in a way that the radiation from two slotlines cancels each other out. The invention is designed based on analytical methods; thus, it significantly reduces the development time. The crossover requires no extra layer to cross two microwave signals and has low radiation loss. The invention is simple to fabricate and design. It produces low radiation loss and can be designed with low insertion loss, with some tradeoff with signal isolation. The microstrip-CPW transition is used as an interface to connect between the device and the circuit outside the package. The via-less microwave crossover is used to allow two signals to cross without using an extra layer or fabrication processing step to enable this function. This design allows the solution to be determined entirely though analytical techniques. In addition, a planar via-less microwave crossover using this technique was proposed. The experimental results show that the proposed crossover at 5 GHz has a minimum isolation of 32 dB. It also has low in-band insertion loss and return loss of 1.2 dB and 18 dB, respectively, over more than 44 percent of bandwidth at room temperature. This microstrip-CPW transition requires the microstrip line to be split into two sections. Each section is connected to a microstrip quarter-wavelength openended stub. A slotline is also placed perpendicular to the microstrip section. The slot is connected to a grounded-end quarter-wavelength slotline and generates a microstrip-slotline transition. When two of these sections are placed in parallel and with the microstrip section combined at transition, a microstrip- CPW transition is formed. The slotline radiation is suppressed as two slots are excited with the electric field in an opposite direction, which cancels the radiation in far field. The invention on the crossover consists of the invented microstrip-CPW transitions combined back-to-back and a microstrip low-pass filter. One signal is crossed through to the microstrip layer, while the other signal is crossed through the CPW line located on the ground plane of the microstrip line. The microstrip low-pass filter produces a narrow line at the crossing point to enhance the system isolation. It also produces broadband response in the operating frequency band. The microstrip-CPW transition allows a microwave signal to travel from microstrip line to CPW line with low radiation loss. The crossover allows two microwave signals to cross with minimal parasitic coupling.

Stevenson, Thomas↗

NASA NTRS2012

The Advanced Technology Microwave Sounder (ATMS): The First 10 Months On-Orbit

The Advanced Technology Microwave Sounder (ATMS) is a new satellite microwave sounding sensor designed to provide operational weather agencies with atmospheric temperature and moisture profile information for global weather forecasting and climate applications. A TMS will continue the microwave sounding capabilities first provided by its predecessors, the Microwave Sounding Unit (MSU) and Advanced Microwave Sounding Unit (AMSU). The first ATMS was launched October 28, 2011 on board the NPOESS Preparatory Project (NPP) satellite. Microwave soundings by themselves are the highest-impact input data used by Numerical Weather Prediction (NWP) models, especially under cloudy sky conditions. ATMS has 22 channels spanning 23-183 GHz, closely following the channel set of the MSU, AMSU-A1/2, AMSU-B, Microwave Humidity Sounder (MHS), and Humidity Sounder for Brazil (HSB). All this is accomplished with approximately 1/4 the volume, 1/2 the mass, and 1/2 the power of the three AMSUs. A description of ATMS cal/val activities will be presented followed by examples of its performance after its first 10 months on orbit.

Kim, Edward↗

NASA NTRS2012

The Advanced Technology Microwave Sounder (ATMS): A New Operational Sensor Series

ATMS is a new satellite microwave sounding sensor designed to provide operational weather agencies with atmospheric temperature and moisture profile information for global weather forecasting and climate applications. ATMS will continue the microwave sounding capabilities first provided by its predecessors, the Microwave Sounding Unit (MSU) and Advanced Microwave Sounding Unit (AMSU). The first ATMS was launched October 28, 2011 on board the Suomi National Polar-orbiting Partnership (S-NPP) satellite. Microwave soundings by themselves are the highest-impact input data used by Numerical Weather Prediction (NWP) models; and ATMS, when combined with the Cross-track Infrared Sounder (CrIS), forms the Cross-track Infrared and Microwave Sounding Suite (CrIMSS). The microwave soundings help meet NWP sounding requirements under cloudy sky conditions and provide key profile information near the surface

Kim, Edward↗

NASA NTRS2015

Hyperspectral Microwave Atmospheric Sounder (HyMAS) - New Capability in the CoSMIR-CoSSIR Scanhead

Lincoln Laboratory and NASA's Goddard Space Flight Center have teamed to re-use an existing instrument platform, the CoSMIR/CoSSIR system for atmospheric sounding, to develop a new capability in hyperspectral filtering, data collection, and display. The volume of the scanhead accomodated an intermediate frequency processor(IFP), that provides the filtering and digitization of the raw data and the interoperable remote component (IRC) adapted to CoSMIR, CoSSIR, and HyMAS that stores and archives the data with time tagged calibration and navigation data. The first element of the work is the demonstration of a hyperspectral microwave receiver subsystem that was recently shown using a comprehensive simulation study to yield performance that substantially exceeds current state-of-the-art. Hyperspectral microwave sounders with approximately 100 channels offer temperature and humidity sounding improvements similar to those obtained when infrared sensors became hyperspectral, but with the relative insensitivity to clouds that characterizes microwave sensors. Hyperspectral microwave operation is achieved using independent RF antenna/receiver arrays that sample the same area/volume of the Earth's surface/atmosphere at slightly different frequencies and therefore synthesize a set of dense, finely spaced vertical weighting functions. The second, enabling element of the proposal is the development of a compact 52-channel Intermediate Frequency processor module. A principal challenge in the development of a hyperspectral microwave system is the size of the IF filter bank required for channelization. Large bandwidths are simultaneously processed, thus complicating the use of digital back-ends with associated high complexities, costs, and power requirements. Our approach involves passive filters implemented using low-temperature co-fired ceramic (LTCC) technology to achieve an ultra-compact module that can be easily integrated with existing radio frequency front-end technology. This IF processor is universally applicable to other microwave sensing missions requiring compact IF spectrometry. The data include 52 operational channels with low IF module volume (less than 100 cubic centimeters) and mass (less than 300 grams) and linearity better than 0.3 percent over a 330,000 dynamic range.

multispectral↗

NASA NTRS2015

Hyperspectral Microwave Atmospheric Sounder (HyMas) - New Capability in the CoSMIR-CoSSIR Scanhead

Lincoln Laboratory and NASA's Goddard Space Flight Center have teamed to re-use an existing instrument platform, the CoSMIRCoSSIR system for atmospheric sounding, to develop a new capability in hyperspectral filtering, data collection, and display. The volume of the scanhead accomodated an intermediate frequency processor(IFP), that provides the filtering and digitization of the raw data and the interoperable remote component (IRC) adapted to CoSMIR, CoSSIR, and HyMAS that stores and archives the data with time tagged calibration and navigation data.The first element of the work is the demonstration of a hyperspectral microwave receiver subsystem that was recently shown using a comprehensive simulation study to yield performance that substantially exceeds current state-of-the-art. Hyperspectral microwave sounders with 100 channels offer temperature and humidity sounding improvements similar to those obtained when infrared sensors became hyperspectral, but with the relative insensitivity to clouds that characterizes microwave sensors. Hyperspectral microwave operation is achieved using independent RF antennareceiver arrays that sample the same areavolume of the Earths surfaceatmosphere at slightly different frequencies and therefore synthesize a set of dense, finely spaced vertical weighting functions. The second, enabling element of the proposal is the development of a compact 52-channel Intermediate Frequency processor module. A principal challenge in the development of a hyperspectral microwave system is the size of the IF filter bank required for channelization. Large bandwidths are simultaneously processed, thus complicating the use of digital back-ends with associated high complexities, costs, and power requirements. Our approach involves passive filters implemented using low-temperature co-fired ceramic (LTCC) technology to achieve an ultra-compact module that can be easily integrated with existing RF front-end technology. This IF processor is universally applicable to other microwave sensing missions requiring compact IF spectrometry.The data include 52 operational channels with low IF module volume (100cm3) and mass (300g) and linearity better than 0.3 over a 330K dynamic range.

sounding↗

DOE OSTI2024

Microwave-assisted ammonia decomposition over metal nitride catalysts at low temperatures

The negative environmental impact of fossil fuel-based energy systems has unveiled the need to develop a CO x -free sustainable hydrogen (H 2 ) economy. Employing a microwave-assisted route, a ternary metal nitride catalyst (i.e., Co 2 Mo 3 N), and a low-temperature-pressure NH 3 decomposition process, this study investigated the possibility of developing a distributed H 2 production process. Here, this study not only explored lower cost-based catalyst systems but also the use of a microwave reactor to increase the energy efficiency of the process. Results from catalytic NH 3 decomposition experiments, performed in microwave reactors on Co 2 Mo 3 N catalyst, demonstrated the peak energy efficiency (of ~0.006 kgH 2 /kWh) at 400 °C in ambient pressure (with an NH 3 conversion >90%) which was around ninety times (~90 x) more efficient than a conventional system. Activation energy calculation also displayed a 20% less energy requirement for the microwave-based process (~31 kJ mol -1 ) than the conventional system (~37 kJ mol -1 ), indicating the advantage of the microwave-based process. Further microwave-assisted catalytic measurements and characterization of the Co 2 Mo 3 N catalyst, using x-ray diffraction (XRD) technique and scanning electron microscopic (SEM) images, revealed the excellent stability of this material at its peak performance (at 400 °C) and illustrated the potential of using this catalyst for a sustainable, economic, and energy-efficient approach for producing CO x -free H 2 .

08 HYDROGEN↗

DOE OSTI2025

Strain-tunable microwave-resonance technique for quantum materials

By integrating a dielectric microwave resonator with a piezoelectric-based strain device, we develop an in situ strain-tunable microwave spectroscopy technique that enables contactless measurements of material properties under strain. To demonstrate the capability of this device, we measure the strain-dependent microwave surface impedance of the representative iron-based superconductor Ba⁢Fe 2 (As 1−𝑥 ⁢P 𝑥 ) 2 at the slightly overdoped composition. We successfully control and observe the suppression of superconductivity under both compressive and tensile anisotropic lattice distortions along the tetragonal [110] T direction, as manifested by changes in the quality factor and resonance frequency shifts of microwave resonance. Furthermore, strain-induced changes in microwave surface resistivity, an extension of conventional DC-limit transport elastoresistivity to the microwave regime, provide information on electronic anisotropy equivalent to that of DC elastoresistivity, while offering a contactless alternative. Furthermore, our strain-tunable cavity therefore serves as a powerful, contactless probe of fundamental material properties under strain and may also potentially facilitate the design of hybrid quantum systems with strain-engineered quantum degrees of freedom.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

Microwave-assisted catalytic conversion of waste biomass and plastic feedstocks via thermochemical routes

Microwave-assisted catalytic conversion of waste feedstocks to fuels and value-added chemicals shows incredible promise as an efficient pathway to support the U.S. Department of Energy’s vision toward strengthening the nation’s energy independence. Microwave-heated systems have the potential to outperform conventional technologies through energy-efficient heating and improved product selectivity. This chapter emphasizes microwave-assisted catalytic approaches for waste conversion, allowing maximum energy recovery and extraction of valuable chemicals from waste feedstock such as biomass and plastics while reducing undesired byproducts. A gap remains in understanding how microwaves interact with materials to enable rapid and selective heating, which is crucial for improving catalytic efficiency. This chapter attempts to address this knowledge gap by proposing mechanisms that explain the microwave-catalytic interactions for efficient conversion of biomass-plastic wastes. In addition, comparisons with conventional catalytic technologies as well as the potential for scale ups and future commercialization of microwave-catalytic waste conversion technologies are also discussed.

microwave-assisted catalytic conversion↗

DOE OSTI2024

Reduction of Iron (III) Oxide in Microwaves Toward Gasification Studies

The purpose of this study is to reduce hematite (Fe2O3) using hydrogen (H2), carbon monoxide (CO), and methane (CH4) gases using microwave irradiation. Conventional temperature programmed reduction of iron phase transformation under H2, CO, and CH4 agree with the literature. Furthermore, the activation energy for the iron phase transformation in a conventional reactor was in the order of H2>CO>CH4, suggesting that CH4 was the best reductant to initiate the reduction at a much lower temperature than CO, and CO was significantly better than H2 atmosphere. Due to the uneven temperature distribution, the apparent activation energy of microwave reduction under H2 was approximately 1/4th when compared to the conventional reduction in H2. X-ray diffraction (XRD) analysis showed a mixed oxide phase in microwave reduction as opposed to the clear phase transformation in conventional studies. To combat the temperature measurement issues in microwave studies, fiber optic sensors and Forward Looking InfraRed (FLIR) sensors were used to acquire the actual temperature distribution in the catalyst bed. Therefore, a reasonably accurate activation energy estimation was achieved in the catalyst bed. Combining these with the characterization and quantification of the different iron phases in microwave reduction will provide a blueprint for future microwave-assisted gasification studies.

Aireddy, Divakar Reddy↗

DOE OSTI2024

From Waste to Clean Fuel: Using Microwave Chemistry to Achieve Process Decarbonization

Microwave co-gasification of plastics and biomass has several advantages over conventional gasification, including enhanced hydrogen production and greater solid-to-gas conversion, as opposed to undesirable char and tar -- via process electrification route. A previous study at NETL has revealed the efficient role of microwave heating, which can liberate the oxygenated free radicals and encourage bond cleavage in non-microwave active plastics, if combined with microwave-active corn stover. However, further reduction of the unwanted tar must be achieved for future process scale-up and higher energy efficiency, which can be realized via a microwave-assisted catalytic approach. This continuous study investigates a series of microwave-active Fe catalysts that can efficiently enhance H2 production and reduce tar for plastic-corn stover co-gasification. The results suggest that in presence of magnetite, hydrogen yield increase 100% as compared to non-catalytic system at similar reaction conditions.

Abedin, Ashraf↗

DOE OSTI2024

Microwave-Assisted Gasification of Biochar: Effect of Operational Parameters and Biochar Composition on Syngas Production

The utilization of microwave-assisted gasification for biomass/plastic is a promising route toward clean energy production, contributing to a reduction in carbon footprint. This method facilitates the conversion of biomass into syngas with enhanced hydrogen (H2) yield, surpassing conventional heating approaches. However, the gasification of biochar, a byproduct resulting from the initial rapid pyrolysis of biomass, appears as a rate-determining step in biomass gasification. To ensure high conversion efficiency, particularly in pilot or larger scales, the maintenance of high biochar reactivity is essential, which can be achieved by introducing catalysts to minimize biochar formation. Furthermore, given the susceptibility of biochar to microwave heating, gaining a comprehensive understanding of its behavior in the presence of microwave-active catalysts under microwave conditions is crucial to obtain valuable insights into the underlying mechanisms, thereby improving overall biomass gasification efficiency. In the previous study, magnetite (Fe3O4) was selected for microwave-assisted gasification for biomass/plastic due to its dual role as a catalyst and microwave absorber and demonstrated considerably enhanced hydrogen production. Herein, Fe3O4 is rationally modified with metal promoters and their synergistic effect toward biochar gasification performance is investigated. The data shows that metal promoted Fe3O4 shows a higher syngas yield than that of pristine Fe3O4 in biochar.

Mai, Duy Hien↗

NASA NTRS1980

Monitoring snowpack properties by passive microwave sensors on board of aircraft and satellites

Snowpack properties such as water equivalent and snow wetness may be inferred from variations in measured microwave brightness temperatures. This is because the emerged microwave radiation interacts directly with snow crystals within the snowpack. Using vertically and horizontally polarized brightness temperatures obtained from the multifrequency microwave radiometer (MFMR) on board a NASA research aircraft and the electrical scanning microwave radiometer (ESMR) and scanning multichannel microwave radiometer (SMMR) on board the Nimbus 5, 6, and 7 satellites, linear relationships between snow depth or water equivalent and microwave brightness temperature were developed. The presence of melt water in the snowpack generally increases the brightness temperatures, which can be used to predict snowpack priming and timing of runoff.

Chang, A. T. C.↗

NASA NTRS1983

Use of microwaves to improve nutritional value of soybeans for future space inhabitants

Whole soybeans from four different varieties at different moisture contents were microwaved for varying times to determine the conditions for maximum destruction of trypsin inhibitor and lipoxygenase activities, and optimal growth of chicks. Microwaving 150 gm samples of soybeans (at 14 to 28% moisture) for 1.5 min was found optimal for reduction of trypsin inhibitor and lipoxygenase activities. Microwaving 1 kgm samples of soybeans for 9 minutes destroyed 82% of the trypsin inhibitor activity and gave optimal chick growth. It should be pointed out that the microwaving time would vary according to the weight of the sample and the power of the microwave oven. The microwave oven used in the above experiments was rated at 650 watts 2450 MHz.

Singh, G.↗

NASA NTRS1983

A microwave systems approach to measuring root zone soil moisture

Computer microwave satellite simulation models were developed and the program was used to test the ability of a coarse resolution passive microwave sensor to measure soil moisture over large areas, and to evaluate the effect of heterogeneous ground covers with the resolution cell on the accuracy of the soil moisture estimate. The use of realistic scenes containing only 10% to 15% bare soil and significant vegetation made it possible to observe a 60% K decrease in brightness temperature from a 5% soil moisture to a 35% soil moisture at a 21 cm microwave wavelength, providing a 1.5 K to 2 K per percent soil moisture sensitivity to soil moisture. It was shown that resolution does not affect the basic ability to measure soil moisture with a microwave radiometer system. Experimental microwave and ground field data were acquired for developing and testing a root zone soil moisture prediction algorithm. The experimental measurements demonstrated that the depth of penetration at a 21 cm microwave wavelength is not greater than 5 cm.

Newton, R. W.↗

NASA NTRS1984

Active microwave responses - An aid in improved crop classification

A study determined the feasibility of using visible, infrared, and active microwave data to classify agricultural crops such as corn, sorghum, alfalfa, wheat stubble, millet, shortgrass pasture and bare soil. Visible through microwave data were collected by instruments on board the NASA C-130 aircraft over 40 agricultural fields near Guymon, OK in 1978 and Dalhart, TX in 1980. Results from stepwise and discriminant analysis techniques indicated 4.75 GHz, 1.6 GHz, and 0.4 GHz cross-polarized microwave frequencies were the microwave frequencies most sensitive to crop type differences. Inclusion of microwave data in visible and infrared classification models improved classification accuracy from 73 percent to 92 percent. Despite the results, further studies are needed during different growth stages to validate the visible, infrared, and active microwave responses to vegetation.

Rosenthal, W. D.↗

NASA NTRS1985

Great microwave bursts and hard X-rays from solar flares

In the present study of the microwave and hard X-ray characteristics of 13 solar flares emitting microwave fluxes greater than 500 solar flux units, simultaneous 3-35 GHz and hard X-ray observations were conducted in the 30-500 keV energy range. An analysis is conducted to determine whether the same distribution of energetic electrons can explain both emissions; tests for any correlations between them yield results suggesting that optically thick microwave emission, near the peak frequency, originates in the same electron population that produces the hard X-rays. A single temperature model and a multitemperature model were tested for consistency with the coincident X-ray and microwave spectra at microwave burst maximum; neither model, however, attempts to explain the high frequency component of the microwave spectrum.

Wiehl, H. J.↗

NASA NTRS1985

Microwave remote sensing from space

Spaceborne microwave remote sensors provide perspectives of the earth surface and atmosphere which are of unique value in scientific studies of geomorphology, oceanic waves and topography, atmospheric water vapor and temperatures, vegetation classification and stress, ice types and dynamics, and hydrological characteristics. Microwave radars and radiometers offer enhanced sensitivities to the geometrical characteristics of the earth's surface and its cover, to water in all its forms - soil and vegetation moisture, ice, wetlands, oceans, and atmospheric water vapor, and can provide high-resolution imagery of the earth's surface independent of cloud cover or sun angle. A brief review of the historical development and principles of active and passive microwave remote sensing is presented, with emphasis on the unique characteristics of the information obtainable in the microwave spectrum and the value of this information to global geoscientific studies. Various spaceborne microwave remote sensors are described, with applications to geology, planetology, oceanography, glaciology, land biology, meteorology, and hydrology. A discussion of future microwave remote sensor technological developments and challenges is presented, along with a summary of future missions being planned by several countries.

Carver, K. R.↗