Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of heat treatment on creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

The objective of this study is to understand the thermal stability of microstructure and its effect on the creep behavior of additively-manufactured 316L stainless steel (AM 316L SS). Creep specimens were fabricated from rods printed by a laser powder bed fusion process. Six different heat treatments, namely 650 °C/1 h, 700 °C/1 h, 750 °C/1 h, 800 °C/1 h, 900 °C/1 h and 1050 °C/1 h were applied to the creep specimens. The heat-treated specimens were creep-tested under the same condition, 550 °C/275 MPa to evaluate the effect of post-build heat treatment on the creep behavior of AM 316L SS. In the temperature range of 650-750 °C, dislocation density within cells, and cell size and wall thickness were affected by the heat treatment, while elemental segregation at boundaries remained unchanged and Mn-enriched Si oxide particles remained stable. In the temperature range of 750-900 °C, concurrent changes were observed in dislocation cell structures, elemental segregation and oxide particles. The 1050 °C-heat treatment removed cell structures and boundary solute segregations, leading to formation of equiaxed grains; Mn-enriched Si oxide particles in the as-built specimen were replaced by more stable Mn-enriched Cr oxides. The creep life of AM 316L SS increased after the heat treatment at 650 °C and then decreased with increasing temperature up to 900 °C where cell/subgrain structures still existed. The creep rate and creep elongation followed an opposite trend. The creep rate can be correlated with the structural parameters of cell/subgrain size and cell wall/boundary thickness and can be rationalized by different strengthening mechanisms of dislocation cells and subgrains. The heat treatment affected strongly the primary and secondary creep but had a minimal effect on the tertiary creep of AM 316L SS.

316L stainless steel↗
DOE OSTI2026

Comparative neutron-irradiation effects on thermal conductivity degradation and dimensional stability of TiC, TiB 2 , and ZrB 2 at 200–1000 °C

Ultra-high-temperature ceramics (UHTCs), including TiC, Ti 11 B₂, and Zr 11 B₂, show great potential for plasma-facing components due to their excellent high-temperature properties prior to irradiation. However, their response to neutron irradiation remains insufficiently understood, limiting robust assessment of their viability for fusion energy applications. Here, this study examines the thermal conductivity, dimensional stability and microstructure of TiC, TiB₂, and ZrB₂ following neutron irradiation at temperatures of 200–1000 °C and fast neutron fluences of 2.0 × 10 25 to 1.1 × 10 26 n/m 2 (E > 0.1 MeV). Lattice swelling measured by synchrotron X-ray diffraction in all three UHTCs was maximized at 200 °C and decreased with increasing irradiation temperature, with no evidence of amorphization observed at 200 °C. Above 600 °C, significant macroscopic volume swelling was observed in irradiated Ti 11 B₂ and Zr 11 B₂, but not in TiC, likely due to cavity formation in the diborides. The post-irradiation thermal conductivity, measured at the irradiation temperature, ranged from 28 to 45 W/m·K, representing a 34–45% reduction relative to the unirradiated material. Notably, neutron-irradiated UHTCs exhibit recoverable thermal conductivity at elevated temperatures, comparable to ferritic–martensitic steels and potentially superior to W when transmutation effects are considered, highlighting promise for shielding or armor plasma-facing components. At 600 °C, both thermal conductivity degradation and lattice swelling saturated at doses exceeding 2–4 dpa.

fusion materials↗
DOE OSTI2021

Microstructure and creep properties of cast near-eutectic Al–Ce–Ni alloys

This study investigates the as-cast and aged microstructures, thermal stability, ambient temperature strengthening, and creep resistance of three ternary Al–Ce–Ni alloys (wt%): near-eutectic Al–10Ce–5Ni (with both eutectic and hypoeutectic regions), hypoeutectic Al-7.5Ce-3.75Ni (with numerous primary Al dendrites), and hypereutectic Al-12.5Ce-6.25Ni (with coarse, blocky primary Al3Ni and Al11Ce3 precipitates and some primary Al dendrites). Depending on the alloy composition and local solidification conditions, the following eutectic morphologies are found: (i) coarse Al–Ce eutectic colonies where Al 11 Ce 3 is in the form of “Chinese script”, (ii) intermingled regions of binary Al–Ce and Al–Ni eutectic colonies, with finer Al 3 Ni and Al 11 Ce 3 fibers, (iii) large ternary eutectic colonies, where the binary Al 3 Ni and Al 11 Ce 3 phases are alternating or intertwining within the individual, fine fibers (diameters of ~60–170 nm, depending on solidification rates), and (iv) ternary eutectic zones (between primary Al dendrites), where fine Al 3 Ni and Al 11 Ce 3 build up a 3D-interconnected network. The high volume fraction of intermetallic phases and extremely fine eutectic spacing/fiber diameter both contribute to high ambient strengthening (higher as-cast microhardness than binary Al–Ce or Al–Ni), and also provide enhanced creep resistance at 300 and 350 °C. Additionally, the alloys are coarsening-resistant up to 425 °C for extended periods, with a gradual decrease in microhardness. The alloys aged at 400 °C to 1050 h show fiber fragmentation and coarsening of the resulting particles, with the faster-diffusing Ni driving more rapid coarsening of the Al 3 Ni particles which engulf finer, more stable Al 11 Ce 3 particles. Severe overaging (performed at 590 °C for 24 h) leads to Al 3 Ni and Al 11 Ce 3 spheroids which remain submicron-sized in eutectic colonies, but micron-sized at colony boundary and at Al dendrite-eutectic interface. Creep resistance at 300 °C of overaged Al–10Ce–5Ni remains substantial, consistent with load-transfer based composite strengthening being an important strengthening mechanism in these alloys, making them excellent candidates for replacement of heavier steel or titanium parts operating under stress up to 300 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hexagonal boron nitride (h-BN) irradiated with 140 MeV protons

Here, hexagonal boron nitride was irradiated with 140 MeV protons to a fluence of ~6 10 20 p/cm 2 at T irr ~200 °C. Isotropic graphite was also irradiated alongside h-BN under similar conditions and fluence to enable direct comparison of the two similar structures. The effects of proton irradiation on dimensional stability and microstructure were studied using precision dilatometry and energy dispersive Xray diffraction techniques revealing by direct comparison to graphite that h-BN can better resist radiation damage from bombardment when irradiated with protons impinging normal to the crystallographic planes or along the crystallographic c-axis. X-ray diffraction experiments also revealed a preferred orientation of the crystallites in bulk samples near the sample surface, an orientation influenced by irradiation. Thermal studies using differential scanning calorimetry and thermogravimetric analysis to 740 °C, augmented by precision dilatometry, provided evidence of subtle phase transitions attributed to residual w-BN in the matrix. Irradiation appears to induce shifting of such transitions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Relativistically transparent magnetic filaments: scaling laws, initial results and prospects for strong-field QED studies

Abstract Relativistic transparency enables volumetric laser interaction with overdense plasmas and direct laser acceleration of electrons to relativistic velocities. The dense electron current generates a magnetic filament with field strength of the order of the laser amplitude (>10 5 T). The magnetic filament traps the electrons radially, enabling efficient acceleration and conversion of laser energy into MeV photons by electron oscillations in the filament. The use of microstructured targets stabilizes the hosing instabilities associated with relativistically transparent interactions, resulting in robust and repeatable production of this phenomenon. Analytical scaling laws are derived to describe the radiated photon spectrum and energy from the magnetic filament phenomenon in terms of the laser intensity, focal radius, pulse duration, and the plasma density. These scaling laws are compared to 3D particle-in-cell (PIC) simulations, demonstrating agreement over two regimes of focal radius. Preliminary experiments to study this phenomenon at moderate intensity ( a 0 ∼ 30) were performed on the Texas Petawatt Laser. Experimental signatures of the magnetic filament phenomenon are observed in the electron and photon spectra recorded in a subset of these experiments that is consistent with the experimental design, analytical scaling and 3D PIC simulations. Implications for future experimental campaigns are discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Atomic Diffusivities of Yttrium, Titanium and Oxygen Calculated by Ab Initio Molecular Dynamics in Molten 316L Oxide-Dispersion-Strengthened Steel Fabricated via Additive Manufacturing

Oxide-dispersion-strengthened (ODS) steels have long been viewed as a prime solution for harsh environments. However, conventional manufacturing of ODS steels limits the final product geometry, is difficult to scale up to large components, and is expensive due to multiple highly involved, solid-state processing steps required. Additive manufacturing (AM) can directly incorporate dispersion elements (e.g., Y, Ti and O) during component fabrication, thus bypassing the need for an ODS steel supply chain, the scale-up challenges of powder processing routes, the buoyancy challenges associated with casting ODS steels, and the joining issues for net-shape component fabrication. In the AM process, the diffusion of the dispersion elements in the molten steel plays a key role in the precipitation of the oxide particles, thereby influencing the microstructure, thermal stability and high-temperature mechanical properties of the resulting ODS steels. In this work, the atomic diffusivities of Y, Ti, and O in molten 316L stainless steel (SS) as functions of temperature are determined by ab initio molecular dynamics simulations. The latest Vienna Ab initio Simulation Package (VASP) package that incorporates an on-the-fly machine learning force field for accelerated computation is used. At a constant temperature, the time-dependent coordinates of the target atoms in the molten 316L SS were analyzed in the form of mean square displacement in order to obtain diffusivity. The values of the diffusivity at multiple temperatures are then fitted to the Arrhenius form to determine the activation energy and the pre-exponential factor. Given the challenges in experimental measurement of atomic diffusivity at such high temperatures and correspondingly the lack of experimental data, this study provides important physical parameters for future modeling of the oxide precipitation kinetics during AM process.

Chemistry↗
DOE OSTI2026

Improving creep resistance of Al-0.27Zr-0.08Sn (wt%) via cold swaging while maintaining high electrical conductivity

This study investigates the effect of mechanical cold work (0, 50, and 90% cross-sectional area reduction via swaging) on the creep properties of cast aluminum alloys with high electrical conductivity including high-purity Al (HP-Al), Al-0.15Zr (Al-Zr), and Al-0.27Zr-0.08Sn (Al-Zr-Sn, wt%). The Al-Zr alloy is strengthened by Zr in solid solution while the Al-Zr-Sn alloy is additionally strengthened by Al3Zr nanoprecipitates (8 nm diameter). After 90% cold swaging, the alloys exhibit grains elongated along the swaging direction with their widths ranging between 8 and 152 μm perpendicular to the swaging direction. Creep testing at 200 °C shows that the minimum creep rate of all 90% swaged alloys shows high sensitivity to stress, which can be modeled via a threshold stress σth. Increasing swaging magnitude from 0 to 50 to 90% in Al-Zr-Sn improves the creep resistance without reducing electrical conductivity. The formation of subgrains, increased dislocation density, and columnar grain structure in swaged alloys all enhance creep resistance. HP-Al swaged to 90% exhibits much lower creep resistance (σth = 18 MPa) due to subgrain coarsening and the absence of precipitates compared to Al-Zr (σth = 40 MPa) and Al-Zr-Sn (σth = 40 MPa), which maintain stable subgrain structures and benefit from solid solution strengthening and Al3Zr nanoprecipitates, respectively. Although Al3Zr precipitates are known to stabilize the deformed microstructure by pinning grain-boundaries, this work demonstrates that Zr in solid solution alone can effectively stabilize the deformed microstructure resulting in enhanced creep resistance. This effect of Zr solute on stabilizing grain boundaries for creep performance was not previously well-defined in the literature. Despite similar creep performances of Al-Zr and Al-Zr-Sn, the latter shows 70% higher room-temperature microhardness and slightly improved electrical conductivity (56%IACS (International Annealed Copper Standard) vs. 57%IACS, respectively). This work provides new insights into creep mechanisms of cold-worked Al–Zr alloys that will guide the design of heat-resistant Al conductors for high-demand applications.

Coello ramirez, Ismael [Northwestern University,]↗
DOE OSTI2022

High Temperature Thick Film Sensor Development Based on Refractory Oxide Semiconductors

Solid-state, high-temperature sensing devices are required for accurate temperature, strain/stress, and failure monitoring for a range of advanced manufacturing, transportation, and military applications. High temperature conditions limit sensing strategies, where typically traditional metal and semiconductor materials are unstable, and the sensing options are limited to optical spectroscopy methods. In addition, strategies to embed the sensors directly within active components and protective thermal refractory are of interest that permit near-environment sensing which is not possible with the traditional electronic materials and components. Rare-earth chromite semiconductors exhibit some properties of interest for high temperature sensing technologies, such as: high microstructure and chemical stability, relatively high electronic conductivity at high temperatures, and relative thermal expansion coefficient matching to refractory thermal protective insulation (such as high-zirconia and -alumina ceramics). In this work, n-type and p-type doped lanthanum chromites compositions were computationally modelled and prepared, and the electrical, thermoelectric, and thermomechanical properties were measured for the obtained material systems. A few compositions were then processed into thick film health and temperature sensors and tested at high temperatures. To establish relative stability under harsh environment conditions, post- mortem microstructure and chemical composition was characterized after extended and cycle testing at high temperatures.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗
DOE OSTI2025

Back to functional hydrides: Effects of neutron-irradiated microstructure on hydrogen retention in yttrium hydride

Functional hydrides are promising candidates for advanced nuclear reactors, particularly in portable or transportable applications, due to their high hydrogen-retention capabilities, enabling efficient neutron moderation, and compact reactor design. However, hydrogen mobility in hydrides at elevated irradiation temperatures poses significant technological challenges, necessitating a comprehensive understanding of their irradiation behavior. Furthermore, this study investigated the microstructural and chemical stability of neutron-irradiated yttrium hydrides to assess their hydrogen-retention capacity. A targeted literature review was also conducted to contextualize neutron-irradiation effects on functional hydrides with regards to structural stability and hydrogen retention. Experimental characterizations revealed that, at high temperatures, irradiated hydrides retained their phase stability, which was likely enhanced by irradiation-induced microstructure evolution. Notably, an amorphous yttrium and oxygen -rich surface layer was present at the free surface of the hydride. Its thickness decreased while a continuous crystalline Y-O-rich layer was formed with increasing neutron damage. Additionally, the number density of dislocation loops and cavities generally increased as a function of neutron dose. First-principles calculations of hydrogen behavior within yttrium vacancy clusters in yttrium hydrides demonstrated vacancy-size-dependent hydrogen stability and configuration, highlighting the role of vacancy geometry in regulating hydrogen retention. Thus, the presence of irradiation-induced dislocation loops and cavities were hypothesized to improve hydrogen retention. Collectively, these findings advance the understanding of hydride behavior under neutron irradiation as well as their technological readiness for portable or transportable nuclear reactors.

Defect clusters↗
DOE OSTI2024

Influence of Joule Heating on the Stability of High Temperature Irradiation-resistant Thermocouples

Development of in-core instrumentation is driven by the pursuit of safer, more economic energy production from the perspective of both existing nuclear reactors and Generation IV reactor designs. Idaho National Laboratory has developed high-temperature irradiation-resistant thermocouples (HTIR-TCs) for temperature sensing inside Generation IV nuclear reactors. These thermocouples are composed of phosphorus-doped niobium (Nb-P) and lanthana-doped molybdenum (Mo-LaO) thermoelements, an alumina (Al2O3) insulation, and a niobium sheath. HTIR-TCs require an initial heat treatment exceeding the maximum service temperature to stabilize the generated electromotive force (EMF) signal. The mechanism behind the stabilization of the HTIR-TCs through traditional heat treatment methods is understood; however, the traditional heat treatment method is expensive, time consuming, and results in a heterogeneous microstructure. Therefore, we investigated a rapid method for stabilization and microstructure homogeneity, through Joule heating. This work evaluates the impact of Joule heating on the thermoelements’ microstructures, chemical stability, and mechanical properties so as to determine the mechanisms by which stabilization of the EMF signal occurs. Accordingly, during the Joule heat treatment, a secondary Nb3P phase coarsened along the length of the Nb-P thermoelement, along with the formation of an interaction region at the Al2O3/niobium interface. The interaction between the alumina insulation and the Nb-P thermoelement was also observed within the Mo-LaO thermoelement. Joule heating induced stability within the generated HTIR-TC EMF signal via the formation of secondary phases within the Nb-P and the interaction between the alumina insulation and the thermoelements.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2022

Evaluating the Rheo-electric Performance of Aqueous Suspensions of Oxidized Carbon Black

Here, the macroscopic properties of carbon black suspensions are primarily determined by the agglomerate microstructure built of primary aggregates. Conferring colloidal stability in aqueous carbon black suspensions should thus have a drastic impact on their viscosity and conductivity. Carbon black was treated with strong acids following a wet oxidation procedure. An analysis of the resulting particle surface chemistry and electrophoretic mobility was performed in evaluating colloidal stability. Changes in suspension microstructure due to oxidation were observed using small-angle X-ray scattering. Utilizing rheo-electric measurements, the evolution of the viscosity and conductivity of the carbon black suspensions as a function of shear rate and carbon content was thoroughly studied. The carboxyl groups installed on the carbon black surface through oxidation increased the surface charge density and enhanced repulsive interactions. Electrostatic stability inhibited the formation of the large-scale agglomerates in favor of the stable primary aggregates in suspension. While shear thinning, suspension conductivities were found to be weakly dependent on the shear intensity regardless of the carbon content. Most importantly, aqueous carbon black suspensions formulated from electrostatically repulsive primary aggregates displayed a smaller rise in conductivity with carbon content compared to those formulated from attractive agglomerates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Assessment of binary eutectic Ni alloys for high-temperature applications via laser remelting

It has been recently demonstrated that eutectic alloys processed by additive manufacturing have excellent high-temperature mechanical properties. We suggest that nickel-base eutectic alloys may enable new combinations of structural and functional properties. To this end, we investigate the processability, microstructure, and thermal stability of five, binary near-eutectic Ni-X (X = B, Ce, La, Y, and Zr) alloys processed via surface laser-remelting. The microstructure of all alloys contain a two-phase lamellar eutectic microstructure consisting of γ-Ni and intermetallic phases; this microstructure is significantly finer (100–200 nm lamellar spacing) in the laser-remelted alloys than in the cast substrate (0.5–1.0 µm lamellar spacing). The microhardness of the laser-remelted alloys (550–770 HV) is 35–50% higher than that of the cast alloys (370–570 HV) due to this finer eutectic spacing. An anomalous eutectic microstructure appears at the meltpool boundaries, containing globular and lamellar γ-Ni phases. The alloys contain a high volume fraction (>50 vol%) of intermetallic phase which forms a continuous network, causing brittleness. Following laser-remelting trials, the alloys showed a high density of solid-state cracks, except for the Ni-Zr alloy which processed well. During thermal exposure at 700 and 900°C for up to 500 h, the eutectic microstructure coarsens. Coarsening occurs heterogeneously and initiates at the meltpool boundaries. This process occurs more slowly in the Ni-Zr and Ni-Y alloys, and more rapidly in the remaining alloys, resulting in greater microhardness retention in the Ni-Zr and Ni-Y alloys following thermal exposure at 700°C. Thus, among the five alloys, the Ni-Zr system exhibits a good combination of high-temperature mechanical properties and processability. Here, we conclude with recommendations for future work on designing additively manufactured alloys based on these eutectic Ni systems.

Additive manufacturing↗
DOE OSTI2022

Multi-principal element grain boundaries: Stabilizing nanocrystalline grains with thick amorphous complexions

Amorphous complexions have recently been demonstrated to simultaneously enhance the ductility and stability of certain nanocrystalline alloys. In this study, three quinary alloys (Cu–Zr–Hf–Mo–Nb, Cu–Zr–Hf–Nb–Ti, and Cu–Zr–Hf–Mo–W) are studied to test the hypothesis that increasing the chemical complexity of the grain boundaries will result in thicker amorphous complexions and further stabilize a nanocrystalline microstructure. Significant boundary segregation of Zr, Nb, and Ti is observed in the Cu–Zr–Hf–Nb–Ti alloy, which creates a quaternary interfacial composition that limits average grain size to 63 nm even after 1 week at ~ 97% of the melting temperature. This high level of thermal stability is attributed to the complex grain boundary chemistry and amorphous structure resulting from multi-component segregation. Furthermore, high-resolution transmission electron microscopy reveals that the increased chemical complexity of the grain boundary region in the Cu–Zr–Hf–Nb–Ti alloy results in an average amorphous complexion thickness of 2.44 nm, approximately 44% and 32% thicker than amorphous complexions previously observed in Cu–Zr and Cu–Zr–Hf alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Oxygen Effects and Selective Oxidation of Group IV Alloying Additions in Group V-Based Refractory Multi-principal Element Alloys

Refractory multi-principal element alloys (RMPEAs) hold significant potential for advancing ultra-high-temperature technologies due to their remarkable strength retention under these conditions. However, the beneficial effects of alloying on microstructural evolution and mechanical properties are often obscured by the presence of interstitial alloying elements. The intricate interactions between substitutional alloying elements of Groups IV, V, and VI and interstitial content, whether intentional or incidental, remain poorly understood. In this study, we investigate the impact of dissolved oxygen on the microstructural evolution and stability of RMPEAs primarily composed of Group V elements, Nb and V, along with Group IV elements Ti, Zr, and Hf. We show that the strong affinity of oxygen for Group IV elements Zr and Hf leads to the internal precipitation of oxides during heat treatment, which competes with the homogenization of the as-cast dendritic microstructure. Here, we demonstrate that careful control and design of oxygen content and Group IV alloying additions are essential to minimize micro-segregation and prevent the detrimental precipitation of internal oxides. To address these challenges, we propose employing non-equilibrium solidification calculations to predict and optimize as-cast solidification structures, thereby reducing the reliance on homogenization processes.

Alloy design↗
DOE OSTI2024

Alloying effects on the microstructure and properties of laser additively manufactured tungsten materials

A large body of literature within the additive manufacturing (AM) community has focused on successfully creating stable tungsten (W) microstructures due to significant interest in their application for extreme environments. However, cracking and additional embrittling features at grain boundaries have resulted in poorly performing materials, stymying the application of AM as a manufacturing technique for W. Several alloying strategies, such as ceramic particles and ductile elements, have emerged with the promise to eliminate cracking while simultaneously enhancing stability against recrystallization. Here, in this work, we provide new insights regarding the defects and microstructural features that result from the introduction of ZrC for grain refinement and NiFe as a ductile reinforcement phase – in addition to the resulting thermophysical and mechanical properties. ZrC is shown to promote microstructural stability with increased hardness due to the formation of ZrO 2 dispersoids. Conversely, NiFe forms into micron-scale FCC phase regions within a BCC W matrix, producing enhanced toughness relative to pure AM W. A combination of these effects is realized in the WNiFe + ZrC system and demonstrates that complex chemical environments coupled with the tuning of AM microstructures provides an effective pathway for enabling laser AM W materials with enhanced stability and performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural Transitions during Powder Metallurgical Processing of Solute Stabilized Nanostructured Tungsten Alloys

Exploiting grain boundary engineering in the design of alloys for extreme environments provides a promising pathway for enhancing performance relative to coarse-grained counterparts. Due to its attractive properties as a plasma facing material for fusion devices, tungsten presents an opportunity to exploit this approach in addressing the significant materials challenges imposed by the fusion environment. Here, we employ a ternary alloy design approach for stabilizing W against recrystallization and grain growth while simultaneously enhancing its manufacturability through powder metallurgical processing. Mechanical alloying and grain refinement in W-10 at.% Ti-(10,20) at.% Cr alloys are accomplished through high-energy ball milling with transitions in the microstructure mapped as a function of milling time. We demonstrate the multi-modal nature of the resulting nanocrystalline grain structure and its stability up to 1300 °C with the coarser grain size population correlated to transitions in crystallographic texture that result from the preferred slip systems in BCC W. Field-assisted sintering is employed to consolidate the alloy powders into bulk samples, which, due to the deliberately designed compositional features, are shown to retain ultrafine grain structures despite the presence of minor carbides formed during sintering due to carbon impurities in the ball-milled powders.

36 MATERIALS SCIENCE↗