Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “large-scale forcing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Large-scale wind-tunnel tests of inverting flaps on a STOL utility aircraft model

A unique inverting flap system was investigated on a large scale deflected slipstream model in the Ames 40 by 80 foot wind tunnel. The subject tests utilized 33% chord double-slotted flaps on a low aspect ratio wing that was fully immersed in the propeller slipstream. Evaluation of the flap effectiveness is aided by comparisons with the results of tests of other flap systems on the same twin propeller, twin tail boom STOL utility aircraft mode. No extreme or abrupt force or moment increments were encountered when the flaps were deflected through a wide range, corresponding to the complete retraction/extension spectrum. The lift and descent capability of the inverting flaps compared very favorably with that of the other flap systems that have been tested on this model, including some with much greater mechanical complexity. As expected, the flaps caused large nose down, pitching moment increments at the high lift settings; however, the trimmed characteristics are still competitive with those obtained from the more complicated flap systems. It is believed that these flaps may have promising potential application to the design of relatively simple STOL utility aircraft with improved performance capabilities. In addition, they may merit consideration as retrofits to existing aircraft with less effective flap systems.

Feistel, T. W.↗

Development of a facility for large-scale testing of multistory buildings

Current experimental research pertaining to response of structures subjected to lateral loads such as strong winds or earthquake motions is limited to either tests of single structural components or small scale multistory structures. The feasibility of developing a facility where large scale multistory structures could be loaded to failure is discussed. The test facility would consist of a series of hydraulic actuators mounted on reaction frames currently in use at the Marshall Space Flight Center for structural testing of spacecraft components. The actuators would be controlled from signals computed by an on-line analysis of measured data. This method of loading could be used to simulate inertial forces resisted by a structure behaving in the non linear range of response subjected to motion at the base or to impulses along the height as would occur during a strong earthquake or wind.

Abrams, D. P.↗

Neutral winds and electric fields in the dust auroral oval. II - Theory and model

A two-dimensional numerical model of the thermosphere is applied to the auroral zone neutral wind, electric field, and plasma density data set, presented in an earlier paper. The model shows that the action of the Lorentz force can be responsible to a great extent for the large zonal velocities near the 150-km altitude. Model equations are described, an explanation of the use of the geophysical conditions is given, and model integrations are compared to the wind measurements. However, for the two-dimensional model to be effective, the atmosphere must not cross too many meridians of local time during the integration period, so that the background state should remain fairly uniform. It is concluded that the two-dimensional model cannot accurately explain the details of the wind profiles because of the three-dimensional character of the physical situation. Thus it is noted that the observed winds were part of a large-scale three-dimensional flow which is only weakly coupled to short-term variations in magnetospheric conditions.

Mikkelsen, I. S.↗

Large-scale wind tunnel tests of a sting-supported V/STOL fighter model at high angles of attack

A new sting model support has been developed for the NASA/Ames 40- by 80-Foot Wind Tunnel. This addition to the facility permits testing of relatively large models to large angles of attack or angles of yaw depending on model orientation. An initial test on the sting is described. This test used a 0.4-scale powered V/STOL model designed for testing at angles of attack to 90 deg and greater. A method for correcting wake blockage was developed and applied to the force and moment data. Samples of this data and results of surface-pressure measurements are presented.

Stoll, F.↗

The development and verification of shuttle orbiter random vibration test requirements

The unique space shuttle vehicle size, weight, and configuration gave rise to problems in determining vibration requirements and in verifying structural integrity for anticipated mission environments. The applications of large-scale vibration testing played a prominent part in qualifying the shuttle for its intended missions. Severe vibration excitation from rocket engines, aerodynamic noise, and onboard equipment are expected on each shuttle flight. Scale-model wind tunnel and rocket firing tests, as well as full-size rocket engine tests were relied on to define the random forcing functions. The determination of structural response to these environments is described as well as evaluations of measured flight data and comparison with predicted design and test criteria.

Coody, M. C.↗

Large-scale motions of the tropics in observations and theory

Charney (1963) characterized the tropical atmosphere in terms of a superposition of large regions of nearly nondivergent circulations containing local subdomains, or 'fissures', of active convection and latent heating. Tropical wave evolution is then appropriately treated in terms of quasi-rotational waves, to the extent that the divergent contribution is small. An attempt is presently made to interpret recent tropical analyses in the aforementioned terms, suggesting extensions of the simplest quasi-rotational model capable of reconciling observations and theory. First GARP Global Experiment (FGGE) observations suggest that strongly divergent local tropical circulations are forced by latent heating and produce important direct modifications of the total wind field; after describing the extent to which the resulting field consists of divergent and rotational components in different analyses of the FGGE data, independent supporting documentation of the results in terms of heating estimates and rainfall observations are given.

Paegle, J.↗

Magnetic reconnection and magnetic activity

A large-scale magnetic field extending through a highly conducting tenuous fluid may become distorted on a small scale as a consequence of slow small-scale shuffling of the magnetic lines of force at the boundaries of the tenuous fluid. Any slow wrapping and winding introduced at the boundaries is distributed along the field (at the Alfven speed). It is a curious and little-known fact that such wrapping and winding possesses no static equilibrium (except for a set of solutions of extreme symmetry). The result is neutral-point reconnection of the strains in the field, rapidly dissipating the wrapping and winding. It is suggested that this is the principal cause of the extreme heating that produces the active corona of the sun and other stars. The shuffling of the footpoints of the magnetic field in the photospheric turbulence introduces small-scale wrapping and twisting into the coronal loops. The work done by the turbulence in twisting the fields is dissipated within a matter 10-20 hours by neutral-point reconnection, introducing heat into the corona at a rate of about 10 Mergs/sq cm sec for photospheric turbulence of 0.5 km/sec. It is suggested that this is the basic cause of the X-ray corona.

Parker, E. N.↗

Sea surface temperature anomalies, planetary waves, and air-sea feedback in the middle latitudes

Current analytical models for large-scale air-sea interactions in the middle latitudes are reviewed in terms of known sea-surface temperature (SST) anomalies. The scales and strength of different atmospheric forcing mechanisms are discussed, along with the damping and feedback processes controlling the evolution of the SST. Difficulties with effective SST modeling are described in terms of the techniques and results of case studies, numerical simulations of mixed-layer variability and statistical modeling. The relationship between SST and diabatic heating anomalies is considered and a linear model is developed for the response of the stationary atmosphere to the air-sea feedback. The results obtained with linear wave models are compared with the linear model results. Finally, sample data are presented from experiments with general circulation models into which specific SST anomaly data for the middle latitudes were introduced.

Frankignoul, C.↗

Continuum calculations of continental deformation in transcurrent environments

A thin viscous sheet approximation is used to investigate continental deformation near a strike-slip boundary. The vertically averaged velocity field is calculated for a medium characterized by a power law rheology with stress exponent n. Driving stresses include those applied along boundaries of the sheet and those arising from buoyancy forces related to lateral differences in crustal thickness. Exact and approximate analytic solutions for a region with a sinusoidal strike-slip boundary condition are compared with solutions for more geologically relevant boundary conditions obtained using a finite element technique. The across-strike length scale of the deformation is approximately 1/4pi x sq rt n times the dominant wavelength of the imposed strike-slip boundary condition for both the analytic and the numerical solutions; this result is consistent with length scales observed in continental regions of large-scale transcurrent faulting. An approximate, linear relationship between displacement and rotation is found that depends only on the deformation length scale and the rheology. Calculated displacements, finite rotations, and distribution of crustal thicknesses are consistent with those observed in the region of the Pacific-North America plate boundary in California.

Sonder, L. J.↗

Large-scale static investigation of circulation-control-wing concepts applied to upper surface-blowing aircraft

The use of a circulation control to deflect turbofan engine thrust beyond 90 deg. has been proven in full-scale static ground tests of the circulation-control-wing/upper-surface-blowing (CCW/USB) concept. This powered high-lift system employs a circular, blown trailing edge to replace the USB mechanical flaps to entrain engine-exhaust flow, and to obtain both a vertical-thrust component and an augmented circulation lift for short takeoff and landing (STOL) applications. Previous tests (Phase 1), done in 1982, of a basic configuration installed on the Quiet Short Haul Research Aircraft confirmed these CCW/USB systems capabilities. A second phase (Phase 2) of full-scale, static, thrust-deflection investigations has reconfirmed the ability to deflect engine thrust from 40 to 102 deg., depending on thrust level. Five new configurations were evaluated and performance improvements noted for those configurations with larger blown span, fences or favorable engine interactions, smaller slot height, and larger radii with less than 180 deg. of CCW surface arc. In general, a 90 deg. circular arc with a smaller slot height provided the best performance, demonstrating that adequate thrust turning can be produced by a trailing-edge shape which may have minimal cruise-performance penalty. Thrust deflections were achieved at considerably lower blowing momentum than was required for the baseline case of Phase 1. Improved performance and versatility were thus confirmed for the CCW/USB system applied to STOL aircraft, where the potential for developing a non-moving-parts pneumatic thrust deflector to rapidly vary horizontal force from thrust to drag, while maintaining constant vertical force, appears quite promising. The conversion from high-lift to lower-drag cruise mode by merely terminating the blowing provides an effective STOL aircraft system.

Shovlin, M. D.↗

Clump 1 - An unusual molecular cloud complex near the Galactic center

The properties of the (C-12)O and (C-13)O emission from Clump I, a complex of molecular clouds which shows the largest noncircular velocities of any molecular material known in the Milky Way, are studied. Observations of the J = 1-0 rotational transitions of the above molecules are reported, and the large-scale distribution and kinematics of the molecular gas in the direction of Clump I are discussed. The small-scale structure is described based on one arcmin resolution of (C-13)O data. Physical properties of the molecular material are derived, and the dynamics of the Clump I clouds are discussed in the context of their stability against Galactic tidal forces. It is concluded that all the clouds in the complex are gravitationally bound, although their outer envelopes may be tidally disrupted by the Galactic potential. The relative motion of the clouds is qualitatively similar to giant molecular cloud complexes in spiral arms of the outer Galactic disk, but the velocities are higher.

Bania, T. M.↗

Zonal wave number variance spectra of stratospheric microwave brightness temperatures

Well-known theoretical predictions suggest that variances of large-scale atmospheric fluctuations, for scales somewhat shorter than those of the forcing mechanisms, should obey a power law, k exp -b, where k is the horizontal wave number. The invariance of the exponent b with season, hemisphere, and latitude is tested using satellite-measured brightness temperatures. Global grids of Tiros-N Microwave Sounding Unit channel 4 measurements, which closely approximate the 30- to 150-mbar layer mean temperature, are constructed for January, March, and August 1979. These grids are zonally Fourier-transformed, and the resulting spectra are averaged over four 18 deg-wide latitude bands. Fits of a power law to these spectra over wave numbers 10-36 and 10-26 give values of b which are independent of season, hemisphere, and latitude band, to within statistical uncertainties. The observed values of b are about 3.6, as compared to theoretical predictions of 3.

Martin, Russell L.↗

A comparative study of rapidly and slowly rotating dynamical regimes in a terrestrial general circulation model

As a preliminary step in the development of a general circulation model for general planetary use, a simplified vesion of thef GISS Model I GCM has been run at various rotation periods to investigate differences between the dynamical regimes of rapidly and slowly rotating planets. To isolate the dynamical processes, the hydrologic cycle is suppressed and the atmosphere is forced with perpetual annual mean solar heating. All other parameters except the rotation period remain fixed at their terrestrial values. Experiments were conducted for rotation periods of 2/3, 1, 2, 4, 8, 16, 64 and 256 days. The results are in qualitative agreement with similar experiments carried out previously with other GCMs and with certain aspects of one Venus GCM simulation. As rotation rate decreases, the energetics shifts from baroclinc to quasi-barotropic when the Rossby radius of deformation reaches planetary scale. The Hadley cell expands poleward and replaces eddies as the primary mode of large-scale heat transport. Associated with this is a poleward shift of the baroclinic zone and jet stream and a reduction of the equator-pole temperature contrast. Midlatitude jet strength peaks at 8 days period, as does the weak positive equatorial zonal wind which occurs at upper levels at all rotation periods. Eddy momentum transport switches from poleward to equatorward at the same period. Tropospheric mean static stability generally increases in the tropics and decreases in midlatitudes as rotation rate decreases, but the global mean static stability is independent of rotation rate. The peak in the eddy kinetic energy spectrum shifts toward lower wavenumbers, reaching wavenumber 1 at a period of 8 days. Implications of these results for the dynamics of Venus and Titan are discussed. Specifically, it is suggested that the extent of low-level convection determines whether the Gierasch mechanism contributes significantly to equatorial superrotation on these planets.

Del Genio, Anthony D.↗

Relationships between persistent large-scale flow anomalies and variation in synoptic-scale eddy activity and cyclogenesis

Observational analyses to study the relationships between large-scale flow anomalies and variations in synoptic-scale eddy activity and cyclogenesis are presented. The way in which changes in the large-scale flow influence the behavior of synoptic-scale eddies and the way in which changes in eddies may feedback to influence the large-scale flow anomalies are examined. Situations characterized by differing large-scale flows are compared, showing well-defined diferences in synoptic-scale eddy activity. The net forcings of anomalous mean flows by eddies as deduced from tendency methods and E-vector analyses suggest that synoptic-scale eddies may play an important role in maintaining certain anomalous flow patterns such as blocking.

Dole, Randall M.↗

The sensitivity of stationary waves to variations in the basic state zonal flow

A linear, primitive equation stationary wave model having high vertical and meridional resolution is used to examine the sensitivity of orographically forced (primarily by Himalayas) stationary waves at middle and high latitudes to variations in the basic state zonal wind distribution. We find relatively little sensitivity to the winds in high latitudes, but remarkable sensitivity to small variations in the subtropical jet. Fluctuations well within the range of observed variability in the jet can lead to large variations in the stationary waves of the high latitude stratosphere, and to large changes even in tropospheric stationary waves. Implications for both sudden warmings and large-scale weather are discussed.

Nigam, Sumant↗

Large-scale Advanced Prop-fan (LAP) static rotor test report

Discussed is Static Rotor Testing of the SR-7L Large Scale Advanced Prop-Fan (LAP). The LAP is an advanced 9 foot diameter, 8 bladed propeller designed and built by Hamilton Standard under contract to the NASA Lewis Research Center. The Prop-Fan employs thin swept blades to provide efficient propulsion at flight speeds up to Mach .85. Static Testing was conducted on a 10,000 HP whirl rig at Wright Patterson Air Force Base. The test objectives were to investigate the Prop-Fan static aerodynamic and structural dynamic performance, determine the blade steady state stressers and deflections and to measure steady and unsteady pressures on the SR-7L blade surface. The measured performance of the LAP correlated well with analytical predictions at blade pitch angles below 30 deg. A stall buffet phenomenon was observed at blade pitch angles above 30 deg. This phenomenon manifested itself by elevated blade vibratory stress levels and lower than expected thrust produced and power absorbed by the Prop-Fan for a given speed and blade angle.

Degeorge, Charles L.↗

Data from a Static-Thrust Investigation of Large-Scale General Research VTOL-STOL Model in Ground Effect

The model was tested at two different elevations with the wing pivot at 1.008 and 2.425 propeller diameters above the ground. The slipstream of the propellers was deflected by tilting the wing and propellers, by deflections of large-chord trailing-edge flaps, and by combinations of flap deflection and wing tilt. Tests were conducted over a range of propeller disk loadings from 7.41 to 29.70 pounds per square foot. Force data for the complete model and pressure distributions for the wing and flaps behind one propeller were recorded and are presented in tabular form without analysis.

Huston, Robert J.↗

STOL Characteristics of a Propeller-Driven, Aspect-Ratio-10, Straight-Wing Airplane with Boundary-Layer Control Flaps, as Estimated from Large-Scale Wind-Tunnel Tests

A study is presented of the improvements in take-off and landing distances possible with a conventional propeller-driven transport-type airplane when the available lift is increased by propeller slipstream effects and by very effective trailing-edge flaps and ailerons. This study is based on wind-tunnel tests of a 45-foot span, powered model, with BLC on the trailing-edge flaps and controls. The data were applied to an assumed airplane with four propellers and a wing loading of 50 pounds per square foot. Also included is an examination of the stability and control problems that may result in the landing and take-off speed range of such a vehicle. The results indicated that the landing and take-off distances could be more than halved by the use of highly effective flaps in combination with large amounts of engine power to augment lift (STOL). At the lowest speeds considered (about 50 knots), adequate longitudinal stability was obtained but the lateral and directional stability were unsatisfactory. At these low speeds, the conventional aerodynamic control surfaces may not be able to cope with the forces and moments produced by symmetric, as well as asymmetric, engine operation. This problem was alleviated by BLC applied to the control surfaces.

Weiberg, James A↗