Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interlayer bonding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Synergistic Coupling of CO2 and H2O during Expansion of Clays in Supercritical CO2-CH4 Fluid Mixtures

A combination of in operando IR and XRD methods were used to investigate the interaction of variably hydrated supercritical CO2-CH4 fluids with Na/NH4/Cs substituted montmorillonites. Comparing the behavior of Na-clay exposed to CH4 versus CO2 dominant fluid phases demonstrated that CO2 disrupts the H-bond network of intercalated H2O. At relatively low potentials of H2O, CO2 facilitates H2O intercalation and expansion of the interlayer region of the Na-clay. In contrast, CO2 inhibited H2O intercalation but promoted expansion of the Cs-clay. The NH4-clay displayed intermediated behavior. Methane likely intercalated the clays but opportunistically, filling unoccupied space after CO2 and H2O actively expanded the interlayer region. By comparing and contrasting the behavior of the Cs and NH4 clays to the Na Clay we conclude that, whereas H2O is required for initial Na-clay expansion, CO2 synergistically facilitated expansion and hydration of Na-clay by mixing with H2O (the entropic contribution) and participating in the outer solvation sphere of Na (the enthalpic contribution). In contrast, CO2 can directly solvate interlayer Cs and NH4 and cause expansion in the absence of H2O; nonetheless, H2O and CO2 also act synergistically to facilitate expansion of the Cs and NH4 clays at low H2O concentrations.

Loring, John S.↗

Structural Implications of Interfacial Hydrogen Bonding in Hydrated Wyoming-Montmorillonite Clay

Montmorillonite (MMT) clay - a layered porous nanomaterial used as seals in engineered waste containment barriers for spent nuclear fuel - adopts discrete hydration/swelling states depending upon surrounding water and ion activities and confining pressure. The structure of nanoconfined water and charge-balancing counterions in the clay mineral interlayers dictate the swelling and mechanical behavior of MMT, so a molecular model for this clay with high structural fidelity is required to accurately predict the reliability of long-term nuclear waste storage. Here, we present a molecular model for MMT that is based on high resolution transmission electron microscopy of Wyoming-MMT single crystals. Imaging data unambiguously show a cis-vacant arrangement of structural hydroxyl groups in the octahedral sheet, whereas existing molecular models assume a centrosymmetric trans-vacant configuration for MMT. Furthermore, using atomistic simulations, we find that the cis-vacant arrangement of structural hydroxyl groups significantly affects the structure of adsorbed water yielding a larger population of hydrogen bonds with bridging oxygens on the tetrahedral sheet and weak hydrogen bonding between the hydroxyl groups in the octahedral sheet and water in the clay mineral interlayers. As a result, water adsorbed in the interlayer is more "ice-like", with stronger ordering and lower density, although the diffusivity of the interlayer species is not significantly diminished. Our improved structural model for MMT provides insight into the energetics of water adsorption, which ultimately dictates its pore- to macro-scale swelling, transport, and fracture properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Advanced reinforcement systems for intermetallic applications

A 2-D axisymmetric model was employed to determine the magnitude of the radial, axial, and hoop stresses caused by the thermal expansion difference between fiber and matrix and which result from the fabrication temperature cycle. Finite element analysis was conducted for single fiber model systems based on SCS-6/Ti3Al+Nb and Al2O3/NiAl. The stress distribution due to the imposition of a graded intermediate layer for each system was determined and included variables of layer thickness and gradation in interlayer chemistry in order to vary the expansion gradient between fiber and matrix. Thermal cycling tests were conducted on sputter coated SCS-6 fibers selectively coated with Ti3Al+Nb, with and without an intermediate layer. Cracking of the Ti3Al+Nb layers was prevented by an interlayer based on Ti-TiN-Ti. The interlayer thickness appeared critical to its efficiency. Similarly, for the case of Al2O3/NiAl, an intermediate layer consisting of a Ni bond coat on the sapphire fiber followed by a graded Al2O3-NiAl layer did not crack when given a thermal excursion to 1100 C and then cooled to room temperature. Acoustic emission tests on single fiber specimens were unsuccessful in detecting load drops associated with the successive fracture of the fiber. For the SCS-6/Ti3Al system this was the result of several factors which included the matrix/fiber ratio and poor bonding of the matrix and fiber. In the case of the Al2O3/NiAl system brittle failure of the NiAl matrix precluded fiber breakdown during tensile loading.

Merrick, Howard F.↗

Coulombically-stabilized oxygen hole polarons enable fully reversible oxygen redox

Stabilizing high-valent redox couples and exotic electronic states necessitates an understanding of the stabilization mechanism. In oxides, whether they are being considered for energy storage or computing, highly oxidized oxide-anion species rehybridize to form short covalent bonds and are related to significant local structural distortions. In intercalation oxide electrodes for batteries, while such reorganization partially stabilizes oxygen redox, it also gives rise to substantial hysteresis. In this work, we investigate oxygen redox in layered Na 2-x Mn 3 O 7 , a positive electrode material with ordered Mn vacancies. We prove that coulombic interactions between oxidized oxide-anions and the interlayer Na vacancies can disfavor rehybridization and stabilize hole polarons on oxygen (O-) at 4.2 V vs. Na/Na + . These coulombic interactions provide thermodynamic energy saving as large as O–O covalent bonding and enable ~40 mV voltage hysteresis over multiple electrochemical cycles with negligible voltage fade. As such, our results establish a complete picture of redox energetics by highlighting the role of coulombic interactions across several atomic distances and suggest avenues to stabilize highly oxidized oxygen for applications in energy storage and beyond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Joining and Integration of Silicon Carbide-Based Ceramic Materials for Aerospace Applications: An Overview

In order to fully utilize silicon carbide-based ceramics and ceramic matrix composites (CMCs) for aerospace and ground based applications, advanced joining and integration technologies are critically needed for achieving large, complex shaped, and integrated components. Careful material selection of joining inter-layers needs to consider chemical and thermal compatibilities with the parent materials that are being joined. Also, optimization needs to be conducted to select the proper processing conditions for achieving robust joints that are well adhered, strong, uniform, crack free, and have minimal residual stresses. NASA GRC developed pressureless and pressure aided approaches for joining ceramics and CMCs include brazing, diffusion bonding, refractory eutectic phase joining, and Single-step Elevated Temperature (SET) Joining. For joining ceramics and CMCs to metals, several brazes have been utilized. Brazing approaches for joining ceramics and metals have also included tailored brazes with multiple interlayers and particle additions. An overview of the joining approaches will be provided. In addition, processing-microstructure-property relationships will be discussed.

Silicon carbide↗

Interspace and Vacancy Modulation: Promoting the Zinc Storage of an Alcohol-Based Organic–Inorganic Cathode in a Water–Organic Electrolyte

Expanding interspace and introducing vacancies are desired to promote the mobility of Zn ions and unlock the inactive sites of layered cathodes. However, this two-point modulation has not yet been achieved simultaneously in vanadium phosphate. Here, in this work, a strategy is proposed for fabricating an alcohol-based organic–inorganic hybrid material, VO 1–x PO 4 ·0.56C 6 H 14 O 4 , to realize the conjoint modulation of the d-interspace and oxygen vacancies. Peculiar triglycol molecules with an inclined orientation in the interlayer also boost the improvement in the conversion rate of V 5+ to V 4+ and the intensity of the P—O bond. Their synergism can ensure steerable adjustment for intercalation kinetics and electron transport, as well as realize high chemical reactivity and redox-center optimization, leading to at least 200% increase in capacity. Using a water–organic electrolyte, the designed Zn-ion batteries with an ultrahigh-rate profile deliver a long-term durability (fivefold greater than pristine material) and an excellent energy density of ≈142 Wh kg –1 (including masses of cathode and anode), thereby substantially outstripping most of the recently reported state-of-the-art zinc-ion batteries. This work proves the feasibility to realize the two-point modulation by using organic intercalants for exploiting high-performance new 2D materials.

25 ENERGY STORAGE↗

Core-shell structured tow-pregs enabled additive manufacturing of continuously reinforced thermoset composites

One of the major challenges in thermally curable polymer composite additive manufacturing is the slow curing time of thermally curable resins, coupled with a significant drop in thermoset viscosity upon heating, making the formation of complex shapes difficult. To tackle these issues, we have introduced a novel rapid composite preformation strategy called Tow-Preg Cladding (TPC). This technique involves the use of a thin and rapidly curable dual-cure resin, which combines a thermally curable resin (such as epoxy) with a fast photo-curable resin. The dual-cure resin is applied as a coating over a thermally curable resin tow-preg, enabling the formation of a rigid cladding that supports and shapes the tow-pregs into the desired geometries and patterns. The key advantage of this approach lies in the sequential formation of an interpenetrating polymer network (IPN) at the interlayer between laminates, resulting from the curing of the photocurable resin and the thermally curable resin sequentially. This IPN formation enhances interlaminar bonding in the composite, contributing to its overall strength and performance. The composites produced using this technique exhibited impressive mechanical properties, including longitudinal tensile strength of 1058.2 MPa, longitudinal tensile modulus of 74.2 GPa, flexural strength of 1080.4 MPa, and flexural modulus of 41.7 GPa. Overall, our Tow-Preg Cladding approach shows great promise in overcoming the challenges associated with thermally curable polymer composite additive manufacturing. It offers a viable solution to creating strong, shape-specific thermoset composites efficiently with enhanced mechanical properties.

42 ENGINEERING↗

Trigonal symmetry breaking and its electronic effects in the two-dimensional dihalides MX 2 and trihalides MX 3

We study the consequences of the approximately trigonal (D 3d ) point symmetry of the transition metal (M) site in two-dimensional van der Waals MX 2 dihalides and MX 3 trihalides. The trigonal symmetry leads to a 2-2-1 orbital splitting of the transition metal d shell, which is best represented by d orbitals that describe the trigonal rather than Oh symmetry. The ligand-ligand bond length differences (rather than metal-ligand) take the role of a Jahn-Teller-like mode and in combination with interlayer distances and dimensionality effects tune the crystal field splittings and bandwidths. These effects, in turn, are amplified by electronic correlation effects—leading to crystal field splittings of the order of 0.1–1 eV between the singlet and the lowest orbital doublet—as opposed to the often assumed degenerate 3 t 2g states. Our calculations explain why most of the materials in this family are insulating, and why these considerations have to be taken into account in realistic models of them. Further, orbital order coupled to various lower symmetry lattice modes may lift the remaining orbital degeneracies, and we explain how these may support unique electronic states using ZrI 2 and CuCl 2 as examples, and offer a brief overview of possible electronic configurations in this class of materials. By building and analyzing Wannier models adapted to the appropriate symmetry we examine how the interplay among trigonal symmetry, electronic correlation effects, and – d orbital charge transfer leads to insulating, orbitally polarized magnetic and/or orbital-selective Mott states, and we provide a simple framework and numerical tool for others. Our paper establishes a rigorous framework to understand, control, and tune the electronic states in low-dimensional correlated halides. Furthermore, our analysis shows that trigonal symmetry and its breaking is a key feature of the two-dimensional halides that needs to be accounted for in search of novel electronic states in materials ranging from CrI 3 to α–RuCl 3 .

2-dimensional systems↗

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improved adherence of sputtered titanium carbide coatings on nickel- and titanium-base alloys

Rene 41 and Ti-6Al-4V alloys were radio frequency sputter coated with titanium carbide by several techniques in order to determine the most effective. Coatings were evaluated in pin-on-disk tests. Surface analysis by X-ray photoelectron spectroscopy was used to relate adherence to interfacial chemistry. For Rene 41, good coating adherence was obtained when a small amount of acetylene was added to the sputtering plasma. The acetylene carburized the alloy surface and resulted in better bonding to the TiC coating. For Ti-6Al-4V, the best adherence and wear protection was obtained when a pure titanium interlayer was used between the coating and the alloy. The interlayer is thought to prevent the formation of a brittle, fracture-prone, aluminum oxide layer.

Wheeler, D. R.↗

Joining and Integration of Silicon Carbide-Based Materials for High Temperature Applications

Advanced joining and integration technologies of silicon carbide-based ceramics and ceramic matrix composites are enabling for their implementation into wide scale aerospace and ground-based applications. The robust joining and integration technologies allow for large and complex shapes to be fabricated and integrated with the larger system. Potential aerospace applications include lean-direct fuel injectors, thermal actuators, turbine vanes, blades, shrouds, combustor liners and other hot section components. Ground based applications include components for energy and environmental systems. Performance requirements and processing challenges are identified for the successful implementation different joining technologies. An overview will be provided of several joining approaches which have been developed for high temperature applications. In addition, various characterization approaches were pursued to provide an understanding of the processing-microstructure-property relationships. Microstructural analysis of the joint interfaces was conducted using optical, scanning electron, and transmission electron microscopy to identify phases and evaluate the bond quality. Mechanical testing results will be presented along with the need for new standardized test methods. The critical need for tailoring interlayer compositions for optimum joint properties will also be highlighted.

Ceramic Matrix Composites↗

Large-gap insulating dimer ground state in monolayer IrTe2

Abstract Monolayers of two-dimensional van der Waals materials exhibit novel electronic phases distinct from their bulk due to the symmetry breaking and reduced screening in the absence of the interlayer coupling. In this work, we combine angle-resolved photoemission spectroscopy and scanning tunneling microscopy/spectroscopy to demonstrate the emergence of a unique insulating 2 × 1 dimer ground state in monolayer 1 T -IrTe 2 that has a large band gap in contrast to the metallic bilayer-to-bulk forms of this material. First-principles calculations reveal that phonon and charge instabilities as well as local bond formation collectively enhance and stabilize a charge-ordered ground state. Our findings provide important insights into the subtle balance of interactions having similar energy scales that occurs in the absence of strong interlayer coupling, which offers new opportunities to engineer the properties of 2D monolayers.

36 MATERIALS SCIENCE↗

A novel design of transitional layer structure between reduced activation ferritic martensitic steels and tungsten for plasma facing materials

Plasma-facing components (PFCs) are among the most critical gaps for fusion energy to establish technical and economic feasibility. Tungsten as a first wall/blanket material in PFCs requires to be integrating with reduced activation ferritic martensitic (RAFM) steels as a structural component. Currently, major drawbacks are the requirement of brazing, the formation of a brittle interface, and a large difference between the coefficients of thermal expansion of tungsten and steel. Here, a novel transitional multilayer structure was designed and investigated to join tungsten and RAFM steels using three interlayers. The composition of each interlayer was selected based on computational thermodynamics and diffusion kinetics to ensure a body-centered cubic (bcc) single-phase structure and prevent the formation of a brittle intermetallic phase region in the temperature range of 600–1150 °C. Although the transitional layer structure was designed for additive manufacturing, spark plasma sintering (SPS) as proof of concept was used to bond the individual layers. Interfaces were investigated using scanning and transmission electron microscopy methods but no layered intermetallic phase was observed. Nanoindentation maps across the interface suggest major hardness differences at the interface between tungsten and the vanadium interlayer, as well as the interface between RAFM steel and the FeCrAl interlayer.

36 MATERIALS SCIENCE↗

Expanding the interlayer spacing of MXene through nanoarchitecture design

MXenes, a diverse class of two-dimensional transition metal carbides and nitrides with distinct surface chem istries, offer remarkable electrochemical and physicochemical properties. Yet, their performance can be hindered by the intrinsic restacking of layers, which restricts surface activity. This review outlines recent advances in interlayer spacing modulation strategies designed to overcome this limitation. A wide range of guest spe cies–including mono- and polyatomic ions, small molecules, low-dimensional nanomaterials, and polymers–are discussed with respect to their intercalation mechanisms, structural effects, and capacity to introduce functional enhancements. These intercalating species interact with MXene via electrostatic forces, hydrogen bonding, redox reactions, or covalent linkages, resulting in stable, expanded nanoarchitectures. The influence of expanded spacing on capacitive behavior is briefly highlighted to illustrate its practical relevance. Although Ti 3 C 2 T x is currently the most extensively investigated MXene, applying these interlayer engineering strategies to other MXene compositions will be essential for accessing a wider range of properties and functionalities.

36 MATERIALS SCIENCE↗

Highly Recyclable, Mechanically Isotropic and Healable 3D-Printed Elastomers via Polyurea Vitrimers

Delamination of three-dimensional (3D) printed polymer materials by fused deposition modeling (FDM) is a long-standing challenge in additive manufacturing (AM). With numerous efforts devoted to modification of commercially available thermoplastic FDM filaments, developing printing polymeric materials with new chemical design that could intrinsically improve interlayer adhesion, especially combined with other benefits, is in high demand. Herein, we developed a polyurea vitrimer with heat-driven malleability, which is printed to different 3D geometries using FDM. Significantly improved interlayer adhesion was observed by post-annealing the printed samples close to its topology-freezing transition temperature upon which fast associative dynamic covalent bonds exchange reaction occurs. Isotropic mechanical properties were achieved as demonstrated with printed tensile samples with different infill directions. Finally, the printed materials could be fully recycled for five generations with retained mechanical properties. Furthermore, the mechanical performance of the printed sample could also be repaired after damage.

36 MATERIALS SCIENCE↗

Thermodynamics and kinetics of H adsorption and intercalation for graphene on 6 H -SiC(0001) from first-principles calculations

Previous experimental observations for H intercalation under graphene on SiC surfaces motivate the clarification of configuration stabilities and kinetic processes related to intercalation. From first-principles density-functional-theory calculations, we analyze H adsorption and intercalation for graphene on a 6H-SiC(0001) surface, where the system includes two single-atom-thick graphene layers: the top-layer graphene (TLG) and the underling buffer-layer graphene (BLG) above the terminal Si layer. Our chemical potential analysis shows that in the low-H coverage regime (described by a single H atom within a sufficiently large supercell), intercalation into the gallery between TLG and BLG or into the gallery underneath BLG is more favorable thermodynamically than adsorption on top of TLG. However, intercalation into the gallery between TLG and BLG is most favorable. We obtain energy barriers of about 1.3 and 2.3 eV for a H atom diffusing on and under TLG, respectively. From an additional analysis of the energy landscape in the vicinity of a step on the TLG, we assess how readily one guest H atom on the TLG terrace can directly penetrate the TLG into the gallery between TLG and BLG versus crossing a TLG step to access the gallery. Finally, we also perform density functional theory calculations for higher H coverages revealing a shift in favorability to intercalation of H underneath BLG and characterizing the variation with H coverage in interlayer spacings.

36 MATERIALS SCIENCE↗

Altered morphology and diffusivity of water confined in MXenes: Machine learning–accelerated computations combined with experiments

Nanoconfined water exhibits unique properties compared to bulk water due to limited quantities, frustrated hydrogen bonding, and surface interactions, which are fundamental for energy storage and transport applications. We integrate machine learning–accelerated ab initio molecular dynamics with x-ray diffraction (XRD) and inelastic neutron scattering (INS) to systematically analyze the thermodynamic and dynamic behavior of water confined between functionalized (-F, -O, and -OH) two-dimensional (2D) Ti 3 C 2 T x MXene layers. As water intercalates between layers, the interlayer spacing exhibits layer-dependent staging characteristics. The water polarization can be flipped by the count and morphology of intercalated molecules interacting with MXene surface groups, resulting in varying electrostatic potential profiles. On the basis of interfacial electrostatic potential, hydrogen bond lifetime, and molecular orientation, we establish a linear combination of exponential model describing water diffusivity. These computational insights align well with experimental x-ray and neutron measurements, suggesting strategies for tuning water morphology and transport by tailoring MXene surface chemistry and water content for electrochemical energy storage and nanofluidic applications.

Tang, Jiawei [Southeast Univ., Nanjing (China)] (O↗

Selenium Interlayer for High-Efficiency Multijunction Solar Cell

A multi junction solar cell is provided and includes multiple semiconducting layers and an interface layer disposed between the multiple semiconducting layers. The interface layer is made from an interface bonding material that has a refractive index such that a ratio of a refractive index of each of the multiple semiconducting layers to the refractive index of the interface bonding material is less than or equal to 1.5.

Landis, Geoffrey A↗