Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ink”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Direct ink writing of shear exfoliated two-dimensional nanomaterial- elastomeric multifunctional nanocomposite

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman analysis. Incorporating exfoliated graphene (40 wt%) increased viscosity by ∼6 orders of magnitude due to enhanced particle–matrix interactions, leading to pronounced yield stress behavior and a yield stress of approximately 1598 Pa, which enabled excellent shape retention during extrusion. Using the DIW technique, porous structures such as desalination membranes, self-sensing bone scaffolds, thermal management coating, and serpentine strain sensors were fabricated. When tested in a direct contact membrane distillation setup, the fabricated membrane demonstrated a promising permeate flux of 21.85 Lm −2 h −1 and a salt rejection of 74.3 %. The fabricated serpentine sensor exhibited stable signal variations under cyclic tensile loading, with a working range of 0–200 % strain and a maximum gauge factor of 43,735. A cell culture test using the printed bone scaffold demonstrated promising cell attachment and proliferation. The DIW printed hBN nanocomposite exhibited reversible shape change under heat, demonstrating potential 4D printing capability and efficient thermal management when exposed to high heat or flame.

Desalination↗
DOE OSTI2020

Three-dimensional hierarchical nanoporous copper via direct ink writing and dealloying

Three-dimensional (3D) hierarchical nanoporous Cu (3DHNP-Cu) is synthesized using a combination of direct ink writing (DIW) based 3D printing, thermal sintering, and chemical dealloying of Mn–Cu alloys. Through tuning processing conditions such as ink composition and cooling rate (after sintering), with consideration of Mn loss during sintering, 3DHNP-Cu with fully bicontinuous nanostructures and negligible residual Mn can be produced after dealloying. The 3DHNP-Cu is comprised of structural features that span seven orders of magnitude, where DIW digitally controls macroscale porous features, thermal sintering and degradation of the binding polymer determines microscale porous features, and dealloying gives rise to nanoscale pores.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Corrosion of novel reactive silver ink and commercial silver-based metallizations in diluted acetic acid

Silver-based metallizations in photovoltaic modules are susceptible to corrosion by acetic acid generated in ethylene vinyl acetate encapsulated modules, resulting in power losses over time. Here, three silver-based metallizations are exposed to diluted acetic acid, in concentrations representative of that found in field-exposed modules. Compositional, morphological, and structural changes of the metallizations are studied over 3000 h of exposure to diluted acetic acid using Raman spectroscopy mapping, X-ray diffraction, and scanning electron microscopy. The three metallizations studied are: 1) a commercial high-temperature fire-through Ag paste, commonly used for Si diffused junction solar cells; 2) a commercial low-temperature paste normally used for silicon heterojunction cells; and 3) a novel low-temperature reactive silver ink shown to be suitable for photovoltaic applications. We find distinct corrosion rates for the high-temperature silver paste and reactive silver ink in the presence of diluted acetic acid. However, the low-temperature silver paste appears to be more corrosion resistant, likely due to a polymer layer that protects the silver particles.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Unveiling the Role of In Situ Al 2 O 3 Passivation in Molecular-Ink-Processed CuIn(S,Se) 2 Photovoltaics

Here, we report on the optimization of in situ passivation of ink-based CuIn(S,Se) 2 thin-film solar cells via controlled incorporation of Al 2 O 3 in CuIn(S,Se) 2 films by the addition of Al(NO 3 ) 3 to the molecular ink precursor. For this purpose, the Al/(Al + In) (AAI) metal ratio was varied from 0.05 to 0.30. We observe that the efficiency of the cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 is consistently higher than those without Al 2 O 3 , especially due to an improvement in open-circuit voltage (V OC ) and fill factor (FF), for all tested AAI ratios. With an AAI of 0.05, a maximum efficiency of 11.2% and an average efficiency of 8.5% (measured across 18 cells) was achieved, compared to 8.5% maximum efficiency and 6.5% average efficiency for Al-free CuIn(S,Se) 2 . Furthermore, we find that cells made of Al 2 O 3 -incorporated CuIn(S,Se) 2 with an AAI of 0.2 show a narrow distribution in the photovoltaic performance, indicating higher reproducibility and higher FF. Energy-dispersive X-ray spectroscopy shows that, at AAI = 0.2, Al 2 O 3 is distributed more homogeneously at the surface of the Al 2 O 3 -incorporated CISSe. Capacitance-voltage measurements reveal a reduced defect density by incorporation of Al 2 O 3 , which could be partly responsible for the higher V OC . Furthermore, using detailed surface analysis with various X-ray and electron spectroscopy methods, we derive chemical and electronic structure information from the surface. With ultraviolet photoelectron (UPS) and inverse photoemission spectroscopies (IPES), the electronic band gap of the CuIn(S,Se) 2 thin-film surface is found to increase from 1.22 to 1.88 eV (+-0.12 eV) with Al 2 O 3 incorporation. This is accompanied by a clear reduction of the conduction band spike at the CdS/CISSe interface due to Al 2 O 3 addition, as derived by both UPS and IPES as well as temperature-dependent V OC measurements.

14 SOLAR ENERGY↗
DOE OSTI2025

Fluid Mechanics Challenges in Direct-Ink-Writing Additive Manufacturing

Direct-ink writing (DIW) has rapidly become a versatile 3D fabrication method due to its ability to deposit a wide range of complex fluids into customizable 3D geometries. This review highlights key fundamental fluid mechanics and soft matter challenges across the different stages of the DIW printing process. The rheology of fluids and suspensions governs the flow behavior through narrow nozzles, posing questions about extrudability, confined flow dynamics, and clogging mechanisms. Downstream, the formation and deposition of extruded filaments involve extensional flows and potential instabilities, while postdeposition dynamics introduces complexities related to yield stress and structural stability. These stages are inherently interdependent, as optimizing material composition without considering filament stability risks compromising the final structure. As DIW applications expand through advanced ink formulations, developing fundamental fluid mechanics frameworks is essential to replace trial-and-error approaches with predictive design methodologies to enable more precise control and improved reliability of the printing process.

3D printing↗
DOE OSTI2021

Direct ink writing techniques for in situ gelation and solidification

Direct ink writing (DIW) is an extrusion-based 3D printing method which prints near ambient temperatures and has one of the broadest printable material selections among additive manufacturing techniques. However, DIW uses viscoelastic materials susceptible to collapse during printing. Overall, one promising route to improve the structural integrity of viscoelastic inks is using in situ curing methods to increase the yield strength of the printed structures after deposition. This review summarizes progress in three representative methods of in situ curing for DIW, including ultra-violet-induced crosslinking, rapid cure of reactive ingredients, and flash vaporization of a solution’s solvent to coagulate dissolved polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Nickel Interlayer for Improved Silver Complex Inks Metallization in GaAs Photovoltaic Devices

Large areas of III-V photovoltaic panels are essential to supplying operational energy for a growing demand of satellites of strategic importance to the United States military, covering a range of applications. High fabrication costs and low manufacturing throughput are key barriers to meeting the necessary supply, which can in turn jeopardize mission success. At the device level, metallization based on printing of complex metal inks has attracted significant research interest due to its potential to substantially reduce processing costs and increase throughput while achieving electrical performance comparable to those of conventional metallization schemes. For GaAs photovoltaic devices, however, reliable electrical contacting remains challenging due to the formation of an interfacial oxide layer at the metal-semiconductor interface. This oxide barrier severely limits current extraction from the PV absorber, resulting in unacceptably high contact resistance. In this study, we report the introduction of a reactive nickel (Ni) interfacial layer between the silver metal fingers and the GaAs substrate to suppress oxide formation while maintaining a low-resistance electrical interface, and show performance data from fully fabricated GaAs devices incorporating the Ni interlayer. These results demonstrate the potential of reactive Ni ink as an effective interfacial layer for improved electrical contacting in low-cost PV metallization schemes.

14 SOLAR ENERGY↗
DOE OSTI2023

Eco–Friendly Solvent Engineered CsPbI 2.77 Br 0.23 Ink for Large–Area and Scalable High Performance Perovskite Solar Cells

The performance of large-area perovskite solar cells (PSCs) has been assessed for typical compositions, such as methylammonium lead iodide (MAPbI 3 ), using a blade coater, slot-die coater, solution shearing, ink-jet printing, and thermal evaporation. However, the fabrication of large-area all-inorganic perovskite films is not well developed. This study develops, for the first time, an eco-friendly solvent engineered all-inorganic perovskite ink of dimethyl sulfoxide (DMSO) as a main solvent with the addition of acetonitrile (ACN), 2-methoxyethanol (2-ME), or a mixture of ACN and 2-ME to fabricate large-area CsPbI 2.77 Br 0.23 films with slot-die coater at low temperatures (40–50 °C). The perovskite phase, morphology, defect density, and optoelectrical properties of prepared with different solvent ratios are thoroughly examined and they are correlated with their respective colloidal size distribution and solar cell performance. Here, the optimized slot-die-coated CsPbI 2.77 Br 0.23 perovskite film, which is prepared from the eco-friendly binary solvents dimethyl sulfoxide:acetonitrile (0.8:0.2 v/v), demonstrates an impressive power conversion efficiency (PCE) of 19.05%. Moreover, the device maintains ≈91% of its original PCE after 1 month at 20% relative humidity in the dark. It is believed that this study will accelerate the reliable manufacturing of perovskite devices.

binary and ternary solvent↗
DOE OSTI2024

Polycaprolactone‐Based Zinc Ink for High Conductivity Transient Printed Electronics and Antennas

Abstract Distributed sensors and electronics can be used in agriculture to optimize crop management and improve environmental outcomes. Electronic devices in these outdoor spaces require medium to long range (>1m) wireless communication of data over several weeks or months, which in turn requires high conductivity (1 × 10 5 Sm −1 ) antennas. Printed bioinert or ecoresorbable conductors, comprising carbon, magnesium, or zinc fillers, typically exhibit conductivity on the order of 10–1000 Sm −1 and lifetimes from a few hours to a few days. A print‐based fabrication process for chemically treated zinc traces, which achieves conductivity of up to 6 × 10 5 Sm −1 is reported here. The ink formulation uses a non‐water‐soluble soil biodegradable polycaprolactone binder. The ink and printing processes reported here led to stable conductive traces that are used in ultra high frequency radio frequency identification (UHF‐RFID) folded dipole antennas operating at 915 MHz. The conductivity of the printed traces is maintained for over 70 days in ambient environments when traces are protected by a biodegradable beeswax encapsulation layer.

Baumbauer, Carol L.↗
DOE OSTI2023

PDMS ‐silica composite gas separation membranes by direct ink writing

Abstract Polydimethylsiloxane (PDMS)‐based membranes containing amine‐functionalized and unfunctionalized silica particles were fabricated via direct ink writing for CO 2 /N 2 gas separation. The printability of the inks was evaluated by rheological measurements, while spectroscopy, microscopy, thermal measurements, and mechanical testing were employed to characterize the printed membranes. The surface morphology of the membranes revealed the absence of voids, demonstrating their suitability for gas separation. The printed membranes also exhibited desirable thermal and mechanical properties (i.e., thermal degradation temperature of 518 °C and tensile strength as high as 1.178 MPa with 529% elongation). The PDMS‐based membranes generally displayed high permeability for CO 2 but slightly low selectivity for the CO 2 /N 2 gas pair. The best‐combined permeability‐selectivity performance of 8794 barrer and selectivity of 11.64 was demonstrated by the printed PDMS membrane containing no SiO 2 fillers. The inclusion of unfunctionalized SiO 2 particles generally increased the membrane's gas permeability but compromised the selectivity. In contrast, membranes with amine‐functionalized silica showed improved selectivity compared to membranes containing unfunctionalized silica. Overall, the performance and characteristics offered by the PDMS/silica composite membranes demonstrated the potential of 3D printing as an economical and sustainable fabrication approach to developing materials for carbon capture applications.

Gutierrez, Dianne B.↗
DOE OSTI2024

Sustainable Production of Biomass‐Derived Graphite and Graphene Conductive Inks from Biochar

Abstract Graphite is a commonly used raw material across many industries and the demand for high‐quality graphite has been increasing in recent years, especially as a primary component for lithium‐ion batteries. However, graphite production is currently limited by production shortages, uneven geographical distribution, and significant environmental impacts incurred from conventional processing. Here, an efficient method of synthesizing biomass‐derived graphite from biochar is presented as a sustainable alternative to natural and synthetic graphite. The resulting bio‐graphite equals or exceeds quantitative quality metrics of spheroidized natural graphite, achieving a RamanI D /I G ratio of 0.051 and crystallite size parallel to the graphene layers (L a ) of 2.08 µm. This bio‐graphite is directly applied as a raw input to liquid‐phase exfoliation of graphene for the scalable production of conductive inks. The spin‐coated films from the bio‐graphene ink exhibit the highest conductivity among all biomass‐derived graphene or carbon materials, reaching 3.58 ± 0.16 × 10 4 S m −1 . Life cycle assessment demonstrates that this bio‐graphite requires less fossil fuel and produces reduced greenhouse gas emissions compared to incumbent methods for natural, synthesized, and other bio‐derived graphitic materials. This work thus offers a sustainable, locally adaptable solution for producing state‐of‐the‐art graphite that is suitable for bio‐graphene and other high‐value products.

Chemistry↗
DOE OSTI2025

Development of direct ink write radially graded alumina/zirconia

Functionally graded materials (FGMs) are of interest in multiple fields, yet many materials combinations are limited by coefficient of thermal expansion (CTE) mismatch. Here, a radially graded alumina/yttria-doped zirconia (Al 2 O 3 /8YZ) FGM is used to demonstrate processing strategies to mitigate CTE and sintering behavior differences between these oxides. FGM materials are especially sensitive to ink stability during printing, as all components (in this case, Al 2 O 3 and 8YZ) must be stabilized in the same dispersant or additive solution. Thus, this system is also ideal to demonstrate ink optimization best practices. Materials were characterized throughout processing to correlate the effects of common additives on both the ceramic particle suspensions and final sintered components. Aggregation observed in the initial additive-containing suspensions were present in the sintered component. The differences in sintering onset temperature and shrinkage rate resulted in internal stresses within the sintered component, which ultimately caused mechanical failure of the component under low stress. In conclusion, a processing strategy was recommended to mitigate the sintering behavior mismatch of alumina and 8 wt% yttria-stabilized zirconia.

Lamm, Benjamin W. [Oak Ridge National Laboratory (↗
DOE OSTI2022

Evaluating the effect of ionomer chemical composition in silver-ionomer catalyst inks toward the oxygen evolution reaction by half-cell measurements and water electrolysis

The effect of anion exchange ionomer (AEI) chemistry on the kinetics of the oxygen evolution reaction (OER) was systematically studied in both half-cell and single-cell electrolysis experiments. OER was studied in 1 M K 2 CO 3 at 50°C using an array of ionomer-silver catalyst inks deposited on Ni foam. Different ionomer modifications were investigated to optimize the OER performance. The AEI used in this work features a block copolymer backbone of polychloromethylstyrene-b-polycyclooctene-b-polychloromethylstyrene which was functionalized with either benzyltrimethylammonium (TMA) or benzylmethylpiperidinium (MPRD) quaternary ammonium cations. Here, using an MPRD quaternary ammonium cation shifted the rate determining step at high overpotentials, ultimately providing enhanced performance. Increasing the catalyst ink dilution was also found to substantially improve mass activity and catalyst utilization (increase from 35 to 88 A g –1 Ag), likely by reducing the ionomer thickness and decreasing transport resistances. In the final ionomer modification, the Ni foam substrate was leveraged to partially hydrogenate the polycyclooctene midblock to be polyethylene-like at the Ni interface. A significant increase in the electrochemical surface area (Cdl increased from 8.8 to 20.8 mF cm –2 ) and performance (by 47 mA cm –2 or 29 A g –1 Ag) was observed with the incorporation of polyethylene. Kinetic results from half-cell experiments were validated via single-cell anion exchange membrane electrolysis experiments, where the optimized electrode displayed enhanced performance in both 1 M K 2 CO 3 and DI H 2 O.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Functional Nano-to-Microstructures by Jet Printing and Direct Ink Writing

Jet-based printing techniques and direct ink writing have emerged as complementary, convergent technologies serving as key platforms in additive manufacturing for functional nano- to microscale architectures. This review highlights how these approaches enable fine feature resolution and three-dimensional structures in advanced electronics and biointerfacing applications. The interplay of fluid mechanics, viscoelastic ink rheology, droplet–substrate interactions, and drying dynamics is examined as a critical determinant of printing fidelity. Application-focused case studies, from flexible thin-film transistors to bioprinted artificial tissues, demonstrate how precise structural control via printing translates to enhanced device performance and new functionality in electronic and biological systems. Finally, we discuss the challenges and future opportunities driving the evolution of these printing platforms toward autonomous, adaptive, and intelligent manufacturing systems.

Luo, Junchen [Sichuan Univ. of Arts and Science (C↗
DOE OSTI2022

Charge-Density-Wave Thin-Film Devices Printed with Chemically Exfoliated 1T-TaS 2 Ink

In this work, we report on the preparation of inks containing fillers derived from quasi-two-dimensional charge-density-wave materials, their application for inkjet printing, and the evaluation of their electronic properties in printed thin-film form. The inks were prepared by liquid-phase exfoliation of CVT-grown 1T-TaS 2 crystals to produce fillers with nm-scale thickness and μm-scale lateral dimensions. Exfoliated 1T-TaS 2 was dispersed in a mixture of isopropyl alcohol and ethylene glycol to allow fine-tuning of filler particles thermophysical properties for inkjet printing. The temperature-dependent electrical and current fluctuation measurements of printed thin films demonstrated that the charge-density-wave properties of 1T-TaS 2 are preserved after processing. The functionality of the printed thin-film devices can be defined by the nearly commensurate to the commensurate charge-density-wave phase transition of individual exfoliated 1T-TaS 2 filler particles rather than by electron-hopping transport between them. The obtained results are important for the development of printed electronics with diverse functionality achieved by the incorporation of quasi-two-dimensional van der Waals quantum materials.

1T-TaS2↗
DOE OSTI2026

Multi-material direct ink writing and co-sintering of gadolinium oxide – zirconium oxide components

Methods for fabrication of multi-material or functionally graded ceramic composite architectures are of interest for numerous applications. However, conventional co-sintering of multi-material ceramic parts is a challenge because differences in the sintering behavior of the two materials leads to interfacial strain and, ultimately, component failure. Direct ink writing (DIW) is an extrusion-based additive manufacturing process that excels at multi-material printing because multiple extrusion nozzles can be installed on the same gantry system. Furthermore, the use of DIW as a method to fabricate multi-material ceramic green bodies offers an additional variable for controlling and potentially matching sintering kinetics in the slurry formulation used for two dissimilar feedstocks. In the work documented in this manuscript, we explored two strategies to successfully co-sinter multi-material ceramic oxides: slurry optimization to match sintering kinetics and material gradients to step from one material to another. This manuscript also quantifies the allowable mismatch that avoids part cracking in solid solution forming multi-material systems and discusses best strategies to reduce mismatch during co-sintering. Inks composed of gadolinium oxide (Gd 2 O 3 ) and zirconium oxide (ZrO 2 ), a surrogate for uranium oxide (UO 2 ), were thermally matched, which resulted in a sintering mismatch reduction of over 10%. It was found that ~1% mismatch is tolerable during debind cycles and that ~5% mismatch is manageable during sintering cycles after slurry formulations are optimized to match the sintering behavior. Use of continuous gradients is shown to reduce sintering mismatch, although geometric resolution may be lost due to solid solution formation.

Snarr, Patrick L. [Oak Ridge National Laboratory (↗
DOE OSTI2020

Nanomorphology of eco-friendly colloidal inks, relating non-fullerene acceptor surface energy to structure formation

Nanoengineered, eco-friendly, solution-processable electroactive materials are in demand for the growing field of printed electronics, and these material requirements can be achieved by the development of waterborne colloidal dispersions. Functionality in these composite materials can be tuned by thermodynamically modifying the material nanomorphology, often by creation of kinetically stabilized aqueous nanoparticle dispersions. In this work we demonstrate that the internal structure of organic nanoparticles is controlled by the surface energy difference between the polymeric donor material and the non-fullerene acceptor (NFA) material. Nanoparticles of the following donor–acceptor combinations, suitable for printed organic photovoltaics, have been synthesized: TQ1:N2200, TQ1:PNDIT10, P3HT:N2200, P3HT:o-IDTBR and P3HT:eh-IDTBR. Advanced synchrotron-based X-ray spectroscopy and microscopy are used to correlate the formation of core–shell nanoparticle morphology to the material surface energy. We subsequently present a viable avenue for customizing the blended nanoparticle structure into (i) core–shell, (ii) molecularly intermixed, or (iii) inverted shell–core structures. Our results showed that TQ1:PNDIT10 and P3HT:o-IDTBR nanoparticles were comprised of a donor-rich shell and an NFA-rich core, however, interestingly we show a reversal to the inverse NFA shell/donor core structure for TQ1:N2200, P3HT:N2200 and P3HT:eh-IDTBR nanoparticles, driven by the low surface energy of N2200 (23.7 mJ m –2 ) and eh-IDTBR (18.3 mJ m –2 ). This article is the first report of a flipped nanoparticle core–shell morphology comprising an NFA-rich shell for the miniemulsion synthesis route. The composition of the shells and cores was able to be controlled by the differential mismatch in the surface energy of the donor and acceptor materials, with ΔG surface > 0, ΔG surface = 0, and ΔG surface < 0 for acceptor core–donor shell, molecularly intermixed, and acceptor shell–donor core, respectively. Accordingly, we introduce an entirely overlooked new figure of merit (FoM) for customizing nanoparticulate colloidal inks: tunable surface energy of non-fullerene-based semiconductors. Finally, the establishment of this FoM opens up electroactive material design to a wide range of functional printing applications with varying device and ink structure requirements, thereby reshaping the nanoengineering toolkit for waterborne colloidal dispersions and hence printed electronics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Printing thermoelectric inks toward next-generation energy and thermal devices

The ability of thermoelectric (TE) materials to convert thermal energy to electricity and vice versa highlights them as a promising candidate for sustainable energy applications. Despite considerable increases in the figure of merit zT of thermoelectric materials in the past two decades, there is still a prominent need to develop scalable synthesis and flexible manufacturing processes to convert high-efficiency materials into high-performance devices. Scalable printing techniques provide a versatile solution to not only fabricate both inorganic and organic TE materials with fine control over the compositions and microstructures, but also manufacture thermoelectric devices with optimized geometric and structural designs that lead to improved efficiency and system-level performances. In this review, we aim to provide a comprehensive framework of printing thermoelectric materials and devices by including recent breakthroughs and relevant discussions on TE materials chemistry, ink formulation, flexible or conformable device design, and processing strategies, with an emphasis on additive manufacturing techniques. Additionally, we review recent innovations in the flexible, conformal, and stretchable device architectures and highlight state-of-the-art applications of these TE devices in energy harvesting and thermal management. Perspectives of emerging research opportunities and future directions are also discussed. While this review centers on thermoelectrics, the fundamental ink chemistry and printing processes possess the potential for applications to a broad range of energy, thermal and electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗