Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ice physics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Effects of Ice Accretion on Aircraft Aerodynamics

The primary objective of this research was to support the development of a new ice accretion model by improving our physical understanding of the ice accretion process through experimental measurements. The focus was on the effect of the initial ice roughness (smooth/rough boundary) on the accretion process. This includes understanding the boundary-layer development over the roughness and especially its effect on the heat transfer which is fundamental to the ice accretion process. The research focused on acquiring the experimental data needed to formulate a new ice accretion physical model. Research was conducted to analyze boundary-layer data taken on a NACA 0012 airfoil with roughness to simulate the smooth/rough boundary. The effect of isolated roughness on boundary-layer transition was studied experimentally to determine if the classical critical roughness Reynolds number criteria could be applied to transition in the airfoil leading-edge area. The effect of simulated smooth/rough boundary roughness on convective heat transfer was studied to complete the study. During the course of this research the effect of free-stream wind tunnel turbulence on the boundary layer was measured. Since this quantity was not well known, research to accurately measure the wind tunnel turbulence in an icing cloud was undertaken. Preliminary results were attained and the final data were acquired, reduced and presented under a subsequent grant.

Bragg, Michael B.↗
NASA NTRS2013

A Systems-Level Perspective on Engine Ice Accretion

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation sector. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. This work focuses on developing an accurate and reliable algorithm for detecting the accretion of ice in the low pressure compressor of a generic 40,000 lbf thrust class engine. The algorithm uses only the two shaft speed sensors and works regardless of engine age, operating condition, and power level. In a 10,000-case Monte Carlo simulation, the detection approach was found to have excellent capability at determining ice accretion from sensor noise with detection occurring when ice blocks an average of 6.8% of the low pressure compressor area. Finally, an initial study highlights a potential mitigation strategy that uses the existing engine actuators to raise the temperature in the low pressure compressor in an effort to reduce the rate at which ice accretes.

May, Ryan D.↗
NASA NTRS2013

An Approach to Detect and Mitigate Ice Particle Accretion in Aircraft Engine Compression Systems

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation sector. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. This work focuses on developing an accurate and reliable algorithm for detecting the accretion of ice in the low pressure compressor of a generic 40,000 lbf thrust class engine. The algorithm uses only the two shaft speed sensors and works regardless of engine age, operating condition, and power level. In a 10,000-case Monte Carlo simulation, the detection approach was found to have excellent capability at determining ice accretion from sensor noise with detection occurring when ice blocks an average of 6.8 percent of the low pressure compressor area. Finally, an initial study highlights a potential mitigation strategy that uses the existing engine actuators to raise the temperature in the low pressure compressor in an effort to reduce the rate at which ice accretes.

May, Ryan D.↗
NASA NTRS2013

An Approach to Detect and Mitigate Ice Particle Accretion in Aircraft Engine Compression Systems

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation sector. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. This work focuses on developing an accurate and reliable algorithm for detecting the accretion of ice in the low pressure compressor of a generic 40,000 lbf thrust class engine. The algorithm uses only the two shaft speed sensors and works regardless of engine age, operating condition, and power level. In a 10,000-case Monte Carlo simulation, the detection approach was found to have excellent capability at determining ice accretion from sensor noise with detection occurring when ice blocks an average of 6.8% of the low pressure compressor area. Finally, an initial study highlights a potential mitigation strategy that uses the existing engine actuators to raise the temperature in the low pressure compressor in an effort to reduce the rate at which ice accretes.

May, Ryan D.↗
NASA NTRS2014

Detection of the Impact of Ice Crystal Accretion in an Aircraft Engine Compression System During Dynamic Operation

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation community. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. Here a detection algorithm is developed which has the capability to detect the impact of ice accretion in the Low Pressure Compressor of an aircraft engine during steady flight as well as during changes in altitude. Unfortunately, the algorithm as implemented was not able to distinguish throttle changes from ice accretion and thus more work remains to be done.

high ice water content↗
NASA NTRS2014

Detection of the Impact of Ice Crystal Accretion in an Aircraft Engine Compression System During Dynamic Operation

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation community. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. Here a detection algorithm is developed which has the capability to detect the impact of ice accretion in the Low Pressure Compressor of an aircraft engine during steady flight as well as during changes in altitude. Unfortunately, the algorithm as implemented was not able to distinguish throttle changes from ice accretion and thus more work remains to be done.

detection↗
NASA NTRS2014

Climate Sensitivity in the Anthropocene

Climate sensitivity in its most basic form is defined as the equilibrium change in global surface temperature that occurs in response to a climate forcing, or externally imposed perturbation of the planetary energy balance. Within this general definition, several specific forms of climate sensitivity exist that differ in terms of the types of climate feedbacks they include. Based on evidence from Earth's history, we suggest here that the relevant form of climate sensitivity in the Anthropocene (e.g. from which to base future greenhouse gas (GHG) stabilization targets) is the Earth system sensitivity including fast feedbacks from changes in water vapour, natural aerosols, clouds and sea ice, slower surface albedo feedbacks from changes in continental ice sheets and vegetation, and climate-GHG feedbacks from changes in natural (land and ocean) carbon sinks. Traditionally, only fast feedbacks have been considered (with the other feedbacks either ignored or treated as forcing), which has led to estimates of the climate sensitivity for doubled CO2 concentrations of about 3 C. The 2×CO2 Earth system sensitivity is higher than this, being approx. 4-6 C if the ice sheet/vegetation albedo feedback is included in addition to the fast feedbacks, and higher still if climate-GHG feedbacks are also included. The inclusion of climate-GHG feedbacks due to changes in the natural carbon sinks has the advantage of more directly linking anthropogenic GHG emissions with the ensuing global temperature increase, thus providing a truer indication of the climate sensitivity to human perturbations. The Earth system climate sensitivity is difficult to quantify due to the lack of palaeo-analogues for the present-day anthropogenic forcing, and the fact that ice sheet and climate-GHG feedbacks have yet to become globally significant in the Anthropocene. Furthermore, current models are unable to adequately simulate the physics of ice sheet decay and certain aspects of the natural carbon and nitrogen cycles. Obtaining quantitative estimates of the Earth system sensitivity is therefore a high priority for future work.

Anthropocene↗
NASA NTRS2019

Analysis of Experimental Ice Accretion Data and Assessment of a Thermodynamic Model During Ice Crystal Icing

This paper evaluates a thermodynamic ice crystal icing model that has been previously presented to describe the possible mechanisms of icing within the core of a turbofan jet engine. The model functions between two distinct ice accretions based on a surface energy balance: freeze-dominated icing and melt-dominated icing. Freeze-dominated icing occurs when liquid water (from melted ice crystals) freezes and accretes on a surface along with the existing ice of the impinging water and ice mass. This freeze-dominated icing is characterized as having strong adhesion to the surface. The amount of ice accretion is partially dictated by a freeze fraction, which is the fraction of impinging liquid water that freezes. Melt-dominated icing occurs as unmelted ice on a surface accumulates. This melt-dominated icing is characterized by weakly bonded surface adhesion. The amount of ice accumulation is partially dictated by a melt fraction, which is the fraction of impinging ice crystals that melts. Experimentally observed ice growth rates suggest that only a small fraction of the impinging ice remains on the surface, implying a mass loss mechanism such as splash, runback, bounce, or erosion. The fraction of mass loss must be determined in conjunction with the fraction of freezing liquid water or fraction of melting ice on an icing surface for a given ice growth rate. This mass loss parameter, however, along with the freeze fraction and melt fraction, are the only experimental parameters that are currently not measured directly. Using icing growth rates from ice crystal icing experiments, a methodology that has been previously proposed is used to determine these unknown parameters. This work takes ice accretion data from tests conducted by the National Aeronautics and Space Administration (NASA) at the Glenn Research Center in 2018 that examined the fundamental physics of ice crystal icing. This paper continues evaluation of the thermodynamic model from a previous effort, with additions to the model that account for sub-freezing temperatures that have been observed at the leading edge of the airfoil during icing. The predicted temperatures were generally in good agreement with measured temperatures. Other key findings include the total wet-bulb temperature being a good first order indicator of whether icing is freeze-dominated (sub-freezing values) or melt-dominated (above freezing). Maximum sticking efficiency values, the fraction of impinging mass that adheres to a surface, was calculated to be about 0.2, and retained this maximum value for a range of melt ratios (0.3 to 0.65 and possibly higher), which is defined as the ratio of liquid water content to total water content. Higher air velocities reduced the maximum sticking efficiency and shifted the icing regime to higher melt ratio values. Finally, the leading edge ice accretion angle was found to be related to ice growth (lower growth rates for smaller angles) and melt ratio (smaller melt ratios resulted in smaller angles, likely due to erosion effects).

Ice-Crystal Icing↗
NASA NTRS1982

Aircraft icing research at NASA

Research activity is described for: ice protection systems, icing instrumentation, experimental methods, analytical modeling for the above, and in flight research. The renewed interest in aircraft icing has come about because of the new need for All-Weather Helicopters and General Aviation aircraft. Because of increased fuel costs, tomorrow's Commercial Transport aircraft will also require new types of ice protection systems and better estimates of the aeropenalties caused by ice on unprotected surfaces. The physics of aircraft icing is very similar to the icing that occurs on ground structures and structures at sea; all involve droplets that freeze on the surfaces because of the cold air. Therefore all icing research groups will benefit greatly by sharing their research information.

Reinmann, J. J.↗
NASA NTRS1984

Observing the polar regions from space

The use of active and passive microwave sensors to provide information on the ice cover in the earth's polar regions is described, along with the ice characteristics that can be measured by such techniques. The continental ice sheets of Greenland and Antarctica represent vast reservoirs of fresh water that can significantly impact sea level if the ice sheets are changing in size. Satellite remote sensing gives information on: sea ice extent and physical characteristics; detailed images of ice flows and open-water leads within the ice pack; sea-ice movement; zones of summer melting and snow-accumulation rates on the continental ice sheets; accurate estimates of ice-surface elevation and detection of zones on the ice sheet that are either thickening or thinning; accurate, all-weather mapping of ice coastlines and large crevasses, and estimates of ice discharge rates from the ice sheets.

Thomas, R. H.↗
NASA NTRS2018

Evaluation of a Thermodynamic Ice Crystal Icing Model Using Experimental Ice Accretion Data

This paper presents the evaluation of a thermodynamic ice crystal icing model, previously presented to describe the possible mechanisms of icing within the core of a turbofan jet engine. It has been proposed that there are two types of distinct ice accretions based on a surface energy balance: freeze-dominated icing and melt-dominated icing. In the former, ice accretion occurs where a freeze fraction (0 to 1) of melted ice crystals freezes on a surface, along with the existing ice of the impinging water and ice mass. This freeze-dominated icing is characterized by having strong adhesion to the surface. In the latter, icing occurs from accumulated unmelted ice on a surface, where a melt fraction (0 to 1) dictates the amount of unmelted impinged ice. This melt-dominated icing is characterized by weakly bonded surface adhesion. The experimentally observed ice growth rates suggest that only a small fraction of the impinging ice remains on the surface, implying a mass loss mechanism such as splash, runback, bounce, or erosion. This mass loss parameter must be determined in conjunction with the fraction of freezing liquid water or fraction of melting ice on an icing surface. This loss parameter, however, along with the freeze and melt fraction, are the only experimental parameters that are currently not measured directly. Using reported icing growth rates from published ice crystal icing experiments, a methodology is proposed to determine these unknown parameters. This work takes reported ice accretion data from tests conducted by the National Aeronautics and Space Administration (NASA) in 2016 and tests NASA collaborated on with the National Research Council (NRC) of Canada in 2012 that examined the fundamental physics of ice crystal icing. Those research efforts sought to generate icing conditions representative of those that occur inside a jet engine when ingesting ice crystals. This paper presents the fundamental equations of the thermodynamic model, the methodology used to determine the aforementioned unknown icing parameters, and results from model evaluation using experimental data. In addition, this paper builds on the previously proposed model by adding a transient conduction term to explain ice growth behavior at the onset of experimental tests that was observed to be different from steady-state ice growth that occurred later in the test run.With the addition of this energy term, this becomes a quasi-steady model. A key finding from this work suggests that mass loss fractions can exceed 0.90 for steady ice growth periods. In addition, due to conductive heat fluxes when using a warmer-than-freezing airfoil, lower mass loss fraction values were calculated during the initial transient period.

Ice-Crystal Ice Accretion↗
NASA NTRS1999

Composition, Physical State, and Distribution of Ices at the Surface of Triton

This paper presents the analysis of near-infrared observations of the icy surface of Triton, recorded on 1995 September 7, with the cooled grating spectrometer CGS4 at the United Kingdom Infrared Telescope (Mauna Kea, HI). This analysis was performed in two steps. The step consisted of identifying the molecules composing Triton's surface by comparing the observations with laboratory transmission spectra (direct spectral analysis ); this also gives information on the physical state of the components.

deBergh, Catherine↗
NASA NTRS2013

ISSM: Ice Sheet System Model

In order to have the capability to use satellite data from its own missions to inform future sea-level rise projections, JPL needed a full-fledged ice-sheet/iceshelf flow model, capable of modeling the mass balance of Antarctica and Greenland into the near future. ISSM was developed with such a goal in mind, as a massively parallelized, multi-purpose finite-element framework dedicated to ice-sheet modeling. ISSM features unstructured meshes (Tria in 2D, and Penta in 3D) along with corresponding finite elements for both types of meshes. Each finite element can carry out diagnostic, prognostic, transient, thermal 3D, surface, and bed slope simulations. Anisotropic meshing enables adaptation of meshes to a certain metric, and the 2D Shelfy-Stream, 3D Blatter/Pattyn, and 3D Full-Stokes formulations capture the bulk of the ice-flow physics. These elements can be coupled together, based on the Arlequin method, so that on a large scale model such as Antarctica, each type of finite element is used in the most efficient manner. For each finite element referenced above, ISSM implements an adjoint. This adjoint can be used to carry out model inversions of unknown model parameters, typically ice rheology and basal drag at the ice/bedrock interface, using a metric such as the observed InSAR surface velocity. This data assimilation capability is crucial to allow spinning up of ice flow models using available satellite data. ISSM relies on the PETSc library for its vectors, matrices, and solvers. This allows ISSM to run efficiently on any parallel platform, whether shared or distrib- ISSM: Ice Sheet System Model NASA's Jet Propulsion Laboratory, Pasadena, California uted. It can run on the largest clusters, and is fully scalable. This allows ISSM to tackle models the size of continents. ISSM is embedded into MATLAB and Python, both open scientific platforms. This improves its outreach within the science community. It is entirely written in C/C++, which gives it flexibility in its design, and the power/speed that C/C++ allows. ISSM is svn (subversion) hosted, on a JPL repository, to facilitate its development and maintenance. ISSM can also model propagation of rifts using contact mechanics and mesh splitting, and can interface to the Dakota software. To carry out sensitivity analysis, mesh partitioning algorithms are available, based on the Scotch, Chaco, and Metis partitioners that ensure equal area mesh partitions can be done, which are then usable for sampling and local reliability methods.

Larour, Eric↗
NASA NTRS2003

Influence of Ice-phase of Hydrometeors on Moist-Convection

Climate models often ignore the influence of ice-phase physics (IPP) of hydrometeors as a second order effect. This has also been true for McRAS (Microphysics of clouds with Relaxed Arakawa Schubert Scheme) developed by the authors. Recognizing that the temperature sounding is critical for moist-convection, and, that IPP would modify it, we investigated the influence of introducing IPP into McRAS coupled to FvGCM (finite volume General Circulation Model with NCAR physics). We analyzed three 3-yr long simulations; the first called Control Case, CC and had no IPP; the other two called Experiments El and E2 had IPP introduced with two different in-cloud freezing assumptions. Simulation El assumed that all hydrometeors remain liquid in the updraft and freeze upon detrainment. Simulation E2 invoked the in-cloud freezing of new condensate generated at subfreezing temperatures in the updraft while old cloud water continued to ascend as liquid. Upon detrainment, this cloud water also froze like in E1. With these assumptions, about 50% of hydrometeors froze in the tower and the rest froze in the anvil. However, in both El and E2, the frozen hydrometeors melted during fall at the first encounter of above freezing ambient temperature. Comparative analysis revealed that El simulated far more mid-level and far less deep clouds while E2 had modified deep and more mid-level clouds as compared to CC along with some major changes around the melt-level. We infer that IPP produced a more realistic response in E2. At the basic level, the results show that ice-phase processes influence convective detrainment at mid- and deep levels in accord with TOGAGOARE observations. The results suggest that IPP can help to mitigate less-than-observed mid-level and over-abundance of deep convective clouds in McRAS.

Sud, Y. C.↗
NASA NTRS1997

Ice velocity at the ice front of the Filchner-Ronne Ice Shelf, Antarctica, as observed with ERS interferometry

ERS images of the two ends of the ice front of the Filchner-Ronne ice shelf (Antarctica) were utilized interferometrically to study the deformation rate of the ice shelf in response to viscous creep. On the western bank of Berkner Island (BI), near Hemmen Ice Rise (HIR), a time series of ERS data acquired in February 1992, in both ascending and descending mode, and with a three-day time interval, were utilized to map the ice velocity in two dimensions. Finite-element ice-shelf flow simulations are compared with the ERS interferograms to interpret the ice motion in terms of the physical constraints on ice-shelf flow. The efforts to fit artificial interferograms generated with model velocity output suggest that the flow regime is strongly influenced by three processes. First, a void-creation process responsible for rifts at coastal margins tends to uncouple the ice shelf from the ice rise and neighboring coast of BI. Secondly, sea ice within the void space appears to act as a binding agent between discrete ice-shelf fragments, allowing rigid-body rotations of these fragments. Third, strain rates appear to be enhanced in a narrow zone adjacent to HIR, implying significant strain softening along the boundary. It is believed that synthetic aperture radar (SAR) interferogram/model intercomparison represents a powerful impetus towards the development of better, more physically realistic ice-shelf flow models.

Rignot, Eric↗
NASA NTRS1988

Physical processes in polar stratospheric ice clouds

A one dimensional model of cloud microphysics was used to simulate the formation and evolution of polar stratospheric ice clouds. Some of the processes which are included in the model are outlined. It is found that the clouds must undergo preferential nucleation upon the existing aerosols just as do tropospheric cirrus clouds. Therefore, there is an energy barrier between stratospheric nitric acid particles and ice particles implying that nitric acid does not form a continuous set of solutions between the trihydrate and ice. The Kelvin barrier is not significant in controlling the rate of formation of ice particles. It was found that the cloud properties are sensitive to the rate at which the air parcels cool. In wave clouds, with cooling rates of hundreds of degrees per day, most of the existing aerosols nucleate and become ice particles. Such clouds have particles with sizes on the order of a few microns, optical depths on order of unity and are probably not efficient at removing materials from the stratosphere. In clouds which form with cooling rates of a few degrees per day or less, only a small fraction of the aerosols become cloud particles. In such clouds the particle radius is larger than 10 microns, the optical depths are low and water vapor is efficiently removed. Seasonal simulations show that the lowest water vapor mixing ratio is determined by the lowest temperature reached, and that the time when clouds disappear is controlled by the time when temperatures begin to rise above the minimum values.

Toon, Owen B.↗
NASA NTRS1989

Physical processes in polar stratospheric ice clouds

The formulation and evolution of polar stratospheric ice clouds are simulated using a one-dimensional model of cloud microphysics. It is found that the optical thickness and particle size of ice clouds depend on the cooling rate of the air in which the cloud formed. It is necessary that there be an energy barrier to ice nucleation upon the preexisting aerosols in order to account for the cooling rate dependence of the cloud properties.

Toon, Owen B.↗
NASA NTRS1986

Biologically relevant physical measurements in the ice-free valleys of southern Victoria Land: soil temperature profiles and ultraviolet radiation

As part of the ongoing comprehensive study of the cryptoendolithic microbial community in the ice-free valleys of southern Victoria Land, thermal properties of the soil and the ultraviolet radiation regime were measured. Although soil temperature profiles have been measured in the ice-free valleys (e.g., Cameron et al. 1970; Cameron 1972), these are the first such data from higher elevations. This is apparently the first time the ultraviolet radiation regime has been measured in the Antarctic.

NASA Program Exobiology↗