Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydration levels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Electrodermal activity as a proxy for sweat rate monitoring during physical and mental activities

Electrodermal activity has long been used for mental activity monitoring by measuring skin conductance at specific locations, such as fingertips, with high sweat gland density. However, electrodermal activity has not been considered useful for physical activity monitoring, where large sweat volumes are generated, resulting in the accumulation of sweat at the skin–electrode interface and, thus, preventing further dynamic response to sweating events. Here we show that electrodermal activity can be used as a proxy for sweat loss measurement under both low and high physical activity levels. We use wearable sweat sensors that consist of water-permeable electrodes and microfluidic-based sweat analysers, and show that skin conductance is proportional to the instantaneous sweat loss. We demonstrate that sweat loss during exercise can be estimated by integrating skin conductance over time, which can be applied to assess the body hydration status of exercisers. From multisite measurements of skin conductance, we show that the wrist, forearm and upper arm are reflective of physical activity levels, whereas the finger is indicative of mental activity. Simultaneous measurement of two different sites selectively decouples mental and physical activities.

Biomedical engineering↗
DOE OSTI2026

Unraveling Grain Boundary Instability in Dense Proton-Conducting Oxides

The long-term stability of protonic ceramic electrolysis cell (PCEC) materials under high-steam operating conditions remains a critical barrier to device commercialization. Here, we investigate the fundamental degradation mechanisms of dense BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3-δ (BCZYYb) electrolytes operated at 550 °C, 50% H 2 O in air. Over 1,000 h, the total electrolyte conductivity decreases by 11.1%, driven primarily by a >130% increase in grain-boundary resistivity. Post-mortem analyses reveal that damage is localized to near-surface grain boundaries extending ∼50 μm into the dense electrolyte pellet. This surface localization indicates that degradation is likely to be severe in thin, device-level electrolytes. Degradation is primarily attributed to chemo-mechanical grain-boundary weakening arising from hydration-induced chemical expansion, culminating in the formation of intergranular cracks oriented parallel to the pellet surface. These internal cracks subsequently react with steam and/or CO 2 , leading to the formation of nanoscale insulating phases, including Ba(OH) 2 , nanocrystalline BaCO 3 , and amorphous Ce/Zr/Y/Yb-containing oxides or hydroxycarbonates. After an initial degradation period of approximately 200 h, the overall conductivity stabilizes. Incorporating NiO sintering aids reduces grain-boundary density by an order of magnitude under identical sintering conditions. Although addition of NiO increases the initial resistivity by >160% at 550 °C, it substantially suppresses grain-boundary instability and mitigates chemical degradation. These findings underscore the urgent need for chemical and/or physical stabilization of BCZYYb electrolytes and offer design guidelines to enable durable, high-performance PCECs.

08 HYDROGEN↗
DOE OSTI2021

Bridging the gap between NMR measured mean silicate chain length and nano-scale silicate polymorphism of calcium silicate hydrates

Variable stoichiometry and silicate polymorphism in calcium-silicate-hydrates (C-S-H) has impeded the revelation of point defects distribution in the silicate tetrahedral network of C-S-H, which resembles tobermorite crystal structure with some bridging tetrahedra (BT) and paired tetrahedra (PT) vacancies in dreierketten chains. Here we use a computational approach to characterize silicate polymorphism by introducing the vacancy ratio of BT to PT (α) and establishing a three-term empirical mean chain length (MCL) formula for different calcium-to‑silicon ratios (Ca/Si) ranging from 1.2 to 2.3. The formula identifies BT and PT controls at low and high α respectively and allows an inverse mapping of polymorphic range based on NMR experiments. The proposed computational framework quantitatively describes silicate polymorphs and links NMR-measured MCL to C-S-H atomistic configurations at the molecular level.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Particle Size Optimization of Thermochemical Salt Hydrates for High Energy Density Thermal Storage

Thermal energy storage (TES) solutions offer opportunities to reduce energy consumption, greenhouse gas emissions, and cost. Specifically, they can help reduce the peak load and address the intermittency of renewable energy sources by time shifting the load, which are critical toward zero energy buildings. Thermochemical materials (TCMs) as a class of TES undergo a solid–gas reversible chemical reaction with water vapor to store and release energy with high storage capacities (600 kWh m −3 ) and negligible self‐discharge that makes them uniquely suited as compact, stand‐alone units for daily or seasonal storage. However, TCMs suffer from instabilities at the material (salt particles) and reactor level (packed beds of salt), resulting in poor multi‐cycle efficiency and high‐levelized cost of storage. In this study, a model is developed to predict the pulverization limit or R crit of various salt hydrates during thermal cycling. This is critical as it provides design rules to make mechanically stable TCM composites as well as enables the use of more energy‐efficient manufacturing process (solid‐state mixing) to make the composites. The model is experimentally validated on multiple TCM salt hydrates with different water content, and effect of R crit on hydration and dehydration kinetics is also investigated.

25 ENERGY STORAGE↗
DOE OSTI2021

Analysis of the Amorphous and Interphase Influence of Comononomer Loading on Polymer Properties toward Forwarding Bioadvantaged Copolyamides

In this paper we present an approach for selectively modifying the properties of semicrystalline polymers by introducing “bioadvantaged” counits. With this approach, the unique functionality of biomass can be leveraged to tailor the properties of the amorphous phase of semicrystalline polymers with minimal impact on crystallinity and thermomechanical properties. As a model case, PA 6,6 copolyamides were produced using the bioadvantaged monomer trans-3-hexenedioic acid (t3HDA). The analogous structure of t3HDA to adipic acid, a PA 6,6 monomer, allows for seamless integration. Screening over the entire composition range identified the t3HDA loading (20 mol%) beyond which properties deviate appreciably from Nylon 6,6. Once identified, copolyamides of suitable compositions were upgraded to commercial quality and fully characterized to assess the influence of counit loading and polymer structure on thermal and mechanical properties. Samples were characterized using gel permeation chromatography (GPC), proton nuclear magnetic resonance spectroscopy (1H NMR), heteronuclear single quantum coherence spectroscopy (HSQC), wide-angle X-ray scattering (WAXS), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), tensile testing, flexural testing, and water absorption testing. t3HDA units were shown to hydrate during the harsh polycondensation to 3-hydroxyhexanedioic acid (3HHDA) and fully incorporate into the polymer backbone. Loading levels up to 20% were shown to have comparable thermal and mechanical properties in the dry state, yet moisture absorption—a known method for improving the toughness, yield strain, and elongation of polyamides—was enhanced by over 100% at 20% loading. This case study on bioadvantaged copolymers elucidates the governing structure-function principles that can be leveraged to forward value-added renewable polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Using Methyl Bromide for Interspecies Cell–Cell Signaling and As a Reporter in a Model Soil Consortium

Synthetic microbial communities are emerging as model systems for studying consortia-scale phenotypes. To establish synthetic biology tools for studying these communities in hard-to-image environmental materials, we evaluated whether a single member of a model soil consortium (MSC) can be programmed to report on gene expression without requiring matrix disruption. For these studies, we targeted a five member MSC that includes Dyadobacter fermentans, Ensifer adhaerens, Rhodococcus sp003130705, Streptomyces sp001905665, and Variovorax beijingensis. By coupling the expression of a methyl halide transferase to a constitutive promoter, we show that Variovorax beijingensis can be programmed to synthesize methyl halides that accumulate in the soil headspace at levels that are ≥24-fold higher than all other MSC members across a range of environmentally-relevant hydration conditions. We find that methyl halide production can report on a MSC promoter that is activated by changes in water potential, and we demonstrate that a synthetic gas signal can be read out directly using gas chromatography and indirectly using a soil-derived Methylorubrum that is programmed to produce a visual output in response to methyl halides. Finally, these tools will be useful for future studies that investigate how MSC respond to dynamic hydration conditions, such as drought and flood events induced by climate change, which can alter soil water potential and induce the release of stored carbon.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

The primary gas phase hydration shell of hydroxide

The number of water molecules in hydroxide’s primary hydration shell has been long debated to be three from the interpretation of experimental data and four from theoretical studies. Here, we provide direct evidence for the presence of a fourth water molecule in hydroxide’s primary hydration shell from a combined study based on high-resolution cryogenic experimental photoelectron spectroscopy and high-level quantum chemical computations. Well-defined spectra of OH - (H 2 O) n clusters (n = 2 to 5) yield accurate electron binding energies, which are, in turn, used as key signatures of the underlying molecular conformations. Although the smaller OH - (H 2 O) 3 and OH - (H 2 O) 4 clusters adopt close-lying conformations with similar electron binding energies that are hard to distinguish, the OH - (H 2 O) 5 cluster clearly has a predominant conformation with a four-coordinated hydroxide binding motif, a finding that unambiguously determines the gas phase coordination number of hydroxide to be four.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Observation of Potential-Induced Hydration on the Surface of Ceramic Proton Conductors Using In Situ Near-Ambient Pressure X-ray Photoelectron Spectroscopy

Interactions of ceramic proton conductors with the environment under operating conditions play an essential role on material properties and device performance. It remains unclear how the chemical environment of material, as modulated by the operating condition, affects the proton conductivity. Combining near-ambient pressure X-ray photoelectron spectroscopy and impedance spectroscopy, we investigate the chemical environment changes of oxygen and the conductivity of BaZr 0.9 Y 0.1 O 3-δ under operating condition. Changes in O 1s core level spectra indicate that adding water vapor pressure increases both hydroxyl groups and active proton sites at undercoordinated oxygen. Applying external potential further promotes this hydration effect, in particular, by increasing the amount of undercoordinated oxygen. The enhanced hydration is accompanied by improved proton conductivity. Here, this work highlights the effects of undercoordinated oxygen for improving the proton conductivity in ceramics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Thermodynamics of Metal Carbonates and Bicarbonates and Their Hydrates for Mg, Ca, Fe, and Cd Relevant to Mineral Energetics

The heats of formation of carbonate, bicarbonate and bicarbonate/hydroxide metal complexes and hydrated versions these complexes of Mg 2+ , Ca 2+ , Fe 2+ , and Cd 2+ are predicted from atomization energies using correlated molecular orbital theory at the CCSD(T) level extrapolated to the complete basis set limit following the Feller-Peterson-Dixon (FPD) approach. Using the calculated gas phase values and the available experimental solid state values, the cohesive energies of selected minerals were calculated. The gas phase decomposition energies into MO, CO 2 and H 2 O follow the order Mg ~ Ca > Cd ~ Fe, and correlate with the hardness of the metal +2 ions. Gas phase hydration energies show that the order is Mg > Fe > Ca ~ Cd. There are a number of bulk hydrated Mg and Ca complexes that occur as minerals but there are few if any for Fe and Cd, suggesting that a number of factors are important in determining the stability of the bulk mineral hydrates. The FPD heats of formation were used to benchmark a range of density functional theory exchange-correlation functionals, including those commonly used in solid state mineral calculations. None of the functionals provided chemical accuracy agreement (± 1 kcal/mol) with the FPD results The best functionals are ωB97X and ωB97X-D with mean average unsigned errors of 10 kcal/mol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Natural carbonation of portland cement with synthetic zeolite Y as a supplementary cementitious material

Risks associated with carbonation are a key limitation to greater replacement levels of ordinary portland cement (OPC) by supplementary cementitious materials (SCMs). The addition of pozzolanic SCMs in OPC alters the hydrate assemblage by forming phases like calcium-(alumina)-silicate-hydrate (C-(A)-S-H). The objective of the present study was to elucidate how such changes in hydrate assemblage influence the chemical mechanisms of carbonation in a realistic OPC system. Here, in this paper, we show that synthetic zeolite Y (faujasite) is a highly reactive pozzolan in OPC that reduces the calcium content of hydration products via prompt consumption of calcium hydroxide from the evolving phase assemblage prior to CO 2 exposure. Suppression of portlandite at moderate to high zeolite Y content led to a more damaging mechanism of carbonation by disrupting the formation of a passivating carbonate layer. Without this layer, carbonation depth and CO 2 uptake are increased. Binders containing 12–18% zeolite Y by volume consumed all the calcium hydroxide from OPC during hydration and reduced the Ca/(Si+Al) ratio of the amorphous products to near 0.67. In these cases, higher carbonation depths were observed after exposure to ambient air with decalcification of C-(A)-S-H as the main source of CO 2 buffering. Binders with either 0% or 4% zeolite Y contained calcium hydroxide in the hydrated microstructure, had higher Ca/(Si+Al) ratios, and formed a calcite-rich passivation layer that halted deep carbonation. Although the carbonated layer in the samples with 12% and 18% zeolite Y contained 70% and 76% less calcite than the OPC respectively, their higher carbonation depths resulted in total CO 2 uptakes that were 12x greater than the OPC sample. Passivation layer formation in samples with calcium hydroxide explains this finding and was further supported by thermodynamic modeling. High Si/Al zeolite additives to OPC should be balanced with the calcium content for optimal carbonation resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Site-Selective Atomic Layer Deposition on Rutile TiO 2 : Selective Hydration as a Route to Target Point Defects

Routes to area-and especially site-selective atomic layer deposition (ALD) remain an enticing challenge in precision surface science, despite the potentially game-changing capability for many energy applications. An unparalleled level of surface reaction control is required to direct ALD to select sites on the same nominal material, for example, targeted growth on distinct phases, facets, step-edges, and/or defects. However, as a sequential surface synthesis method, ALD is uniquely suited to these challenges, including the possibility of selective deposition at defective surface atom arrangements. Here, we computationally identify conditions for site-selective ALD through hydration of surface defects, including oxygen vacancies and titanium interstitials on low-index rutile TiO 2 facets. First-principles computation is used to predict, as a function of temperature, the hydroxylation of defects that are targeted by proton-exchange-mediated ALD processes. In situ ellipsometric measurements of ALD Al 2 O 3 nucleation on TiO 2 (110) single crystals prepared with and without abundant oxygen vacancies demonstrate striking contrast, corroborating computational predictions and revealing a mechanistically clear path to site-selective ALD.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Influence of mixing on the generation of nanoparticles in cement systems

In this work, we study the effect of mixing intensity on the size and concentration of nanoparticles in quartz and cement systems. We vary the local shear rate in the studied suspensions induced by mixing by either changing solid volume fraction or mixing speed. Our results obtained on quartz, cement and quartz-cement suspensions provide a master curve relating the concentration of nanoparticles in the pore solution as a function of the local shearing conditions computed at a micromechanical level. Our results suggest, in accordance with literature, that high mixing intensity is at the origin of a detachment of nano-hydrates from the surface of cement particles. These nanoparticles can be stabilized and therefore detected in the pore-solution only in the presence of superplasticizers, which inhibit their agglomeration to other particles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Plastic deformation mechanism of calcium-silicate hydrates determined by deviatoric-stress Raman spectroscopy

Highlights: • C-(A-)S-H samples under stress were characterized at the bond and grain level. • Small angle scattering showed that 720 MPa reduced grain thickness by 30%. • In-situ Raman showed that cross-linked C-A-S-H slips along its intralayer. • However, in-situ Raman showed that C-S-H slips along the interlayer. • In-situ Raman also showed a growth in CaCO{sub 3}, indicating fracture in both samples. Creep of the cement matrix affects the structural stability of concrete. In Portland cements, the creep is largely controlled by the binding phase calcium-(aluminum-)silicate-hydrate, or C-(A-)S-H. This phase has a lamellar structure and under deviatoric stress aligns its c-axis with the principal stress. However, the limiting resistance to this reorientation is unknown at the nanocrystalline level. Small-angle X-ray scattering shows that the lamellae thickness decreases under 100's MPa deviatoric stress. Deviatoric stress Raman spectroscopy shows that there are two ways that this break-up can occur. If the material's silicate chains are cross-linked, then strain in SiO bonds does not increase above certain stresses, indicating a relaxation adjacent to the SiO bond. If the chains are not cross-linked, then the silicate chains are broken up by rastering against each other, introducing defects. These results show that the plastic deformation of C-(A-)S-H is relevant for Portland cement creep.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structure and thermodynamics of water adsorption in NU-1500-Cr

Abstract Metal-organic frameworks (MOFs) are a class of materials with diverse chemical and structural properties, and have been shown to effectively adsorb various types of guest molecules. The mechanism of water adsorption in NU-1500-Cr, a high-performance atmospheric water harvesting MOF, is investigated using a combination of molecular dynamics simulations and infrared spectroscopy. Calculations of thermodynamic and dynamical properties of water as a function of relative humidity allow for following the adsorption process from the initial hydration stage to complete filling of the MOF pores. Initial hydration begins at the water molecules that saturate the open Cr 3+ sites of the framework, which is then followed by the formation of water chains that extend along the channels connecting the hexagonal pores of the framework. Water present in these channels gradually coalesces and fills the hexagonal pores sequentially after the channels are completely hydrated. The development of hydrogen-bond networks inside the MOF pores as a function of relative humidity is characterized at the molecular level using experimental and computational infrared spectroscopy. A detailed analysis of the OH-stretch vibrational band indicates that the low-frequency tail stems from strongly polarized hydrogen-bonded water molecules, suggesting the presence of some structural disorder in the experimental samples. Strategies for designing efficient water harvesting MOFs are also proposed based on the mechanism of water adsorption in NU-1500-Cr.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Development of an ERT‐Based Framework for Bentonite Buffers Monitoring From Laboratory Tests: 1. Characterizing Thermal–Hydrological–Mechanical Processes

Abstract Bentonite clay is widely used in engineered barrier systems for the permanent disposal of high‐level radioactive waste due to its low permeability, high swelling capacity, and thermal stability. However, the complex thermal‐hydrological‐mechanical (THM) processes induced by heating from decaying radioactive waste and hydration from surrounding rock can lead to heterogeneous changes that are difficult to measure and predict. This study develops an Electrical Resistivity Tomography (ERT)‐based framework for monitoring THM processes, progressing from sample‐scale to bench‐scale tests, to inform field‐scale applications. Sample‐scale tests analyzed small bentonite samples under controlled variations in water content, temperature, and porosity to establish fundamental resistivity relationships. Bench‐scale tests involved larger bentonite columns subjected to heating (up to 200°C) and hydration under controlled pressure, simulating repository conditions. ERT measurements, complemented by X‐ray CT imaging, temperature monitoring, and tracing sensors, revealed coupled THM processes, such as hydration‐induced compression, swelling, and thermal gradients, leading to complex resistivity patterns. The results demonstrate the potential of ERT for capturing THM‐induced resistivity changes, though challenges remain in upscaling and quantitative analysis. This study evaluates laboratory test capabilities and proposes future improvements for understanding THM‐induced resistivity responses. A conceptual framework for ERT implementation in field‐scale monitoring is presented, synthesizing findings from both scales and exploring how ERT data can inform long‐term modeling and reduce prediction uncertainties. Overall, this ERT‐based framework offers a robust method for monitoring bentonite buffers, aiding in early issue detection and supporting the safe long‐term disposal of radioactive waste in geological repositories, while highlighting the need for future development. Plain Language Summary Bentonite clay is crucial in engineered barrier systems (EBS) for containing high‐level radioactive waste due to its ability to absorb water, swell, seal and remain stable under high temperatures. When bentonite absorbs water and heats up from radioactive decay, it experiences complex changes in its physical and mechanical properties. Understanding these changes is important for ensuring the long‐term safety and effectiveness of EBS. This study used Electrical Resistivity Tomography (ERT), a non‐invasive method that measures electrical conductivity to monitor these changes during laboratory experiments. The ERT data revealed significant variations in resistivity corresponding to changes in water content, temperature, and density, providing detailed spatial and temporal insights into the behavior of bentonite. These findings enhance our ability to predict the long‐term performance of bentonite barriers, ensuring the safe containment of radioactive waste. By improving our understanding of bentonite's behavior, this research supports the development of more reliable and effective barrier systems for radioactive waste disposal, protecting the environment and public health. Key Points ERT monitoring was employed to capture resistivity changes in bentonite during controlled heating and hydration experiments, providing insights into THM processes ERT data reveal significant resistivity changes correlated with water content, temperature, and mechanical effects, enhancing the understanding of THM dynamics in bentonite This study explores the potential of the framework for application in field‐scale EBS monitoring, emphasizing the need for integrating additional geophysical methods for comprehensive subsurface imaging

Chen, Hang↗
DOE OSTI2021

Molecular level study of uni/multi-axial deformation response of tobermorite 11 Å: A force field comparison study

Molecular deformation response of tobermorite 11 Å (a mineral analogue to C-S-H, the primary constituent of hydrated cement paste) under uni/tri-axial loading (both tension and compression) has been investigated in this manuscript using empirical and reactive force fields. A comparison has been chalked out amongst the responses using different force fields. Evolution of atomic environment during the deformation have studied using reactive force field. This study demonstrate the key observations on the application of different force fields to study the large deformation behaviour of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structure of Water Adsorbed on Nanocrystalline Calcium Silicate Hydrate Determined from Neutron Scattering and Molecular Dynamics Simulations

Calcium silicate hydrate (C-S-H) is a disordered, nanocrystalline material that acts as a primary binding phase in Portland cement. Thin films of water are present on the surfaces and in nanopores of C-S-H, impacting many of its chemical and mechanical properties, such as ion transport, creep, or thermal behavior. Despite decades of research, a full understanding of the structural details of adsorbed, confined, and bulk water in C-S-H remains elusive. In this work, we applied a multitechnique study involving molecular dynamics (MD) simulations validated by neutron diffraction with isotopic substitution (NDIS) and X-ray scattering methods to investigate the structure of water in C-S-H and C-A-S-H (an Al-bearing, low-CO 2 C-S-H substitute). Direct comparison of NDIS data with the MD results reveals that the structure of confined and interfacial water differs significantly from the bulk water and exhibits a larger degree of mesoscale ordering for more hydrated C-S-H structures. As a result, this observation suggests an important role of water as a stabilizer of the atomistic-level structure of C-S-H.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The Anisotropic Adsorption of De Novo Allosteric Two‐Component Protein Fibers on Mica Surfaces

Protein adsorption at solid–liquid interfaces underlies many biomedical and materials applications, yet the mechanisms governing adsorption of proteins and their assemblies remain poorly understood. Here we investigate de novo–designed proteins that self-assemble into three fibrillar morphologies — small (S), large (L), and helical (H)—on muscovite mica. S-fibers are metastable, forming first but diminishing as L- and H-fibers develop and deposit. Adsorption of both fibers and monomers depends on fiber morphology and solvent environment, which is modulated by the substrate. The anisotropic surface features of the fiber types—long axis of S- and L-fibers and helical grooves of H-fibers—correlate with specific crystallographic directions on mica (001). S- and L-fibers align along the unique lattice axis, while the substrate-facing groove of H-fibers preferentially aligns along the remaining symmetry-related directions. Increasing potassium chloride (KCl) concentrations to molar levels alters adsorption, decreasing monomer coverage relative to fibers. These observations, interpreted through the effect of interfacial interface, indicate that ion-mediated modulation of hydration layers governs electrostatic interactions and alignment. This study reveals how coupling between protein topography, substrate crystallography, and hydration structure dictates selective adsorption and orientation of protein assemblies, offering insights for rational biomolecular material design.

AFM↗