SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Pulse amplitude discriminator is specially designed for nuclear counting applications. At very high rates, the threshold is stable. The output-pulse width and the dead time change negligibly. The unit incorporates a provision for automatic dead-time correction.
The Second Target Station (STS) at the Oak Ridge National Laboratory Spallation Neutron Source (SNS) is expected to produce a neutron source that is the brightest in the world, having a significantly higher peak brightness compared to the First Target Station (FTS), where the reflectometry instruments already fall short of being able to handle the highest available flux by a factor of ~100. The neutron reflectometers at the SNS FTS are not suitable for the reflectometers planned for the SNS STS because of its unprecedentedly high peak brightness and the already limited capabilities of these instruments at high count rates. Furthermore, the high rate instruments that are now under development are expected to underperform with regard to gamma sensitivity, meaning that signal-to-noise will be reduced and they will be unable to measure weaker reflectance phenomena in the presence of the significant prompt gamma flash at SNS. To address these challenges, we conducted research to advances associated instruments, techniques, and capabilities for the SNS STS reflectometers. More specifically, we investigated the development of a scalable, 2-D positive-sensitive, pixelated, scintillator-based neutron detector module based on a newly developed scintillator. The work has potential for impact on future neutron reflectometry instruments and neutron science performed at the SNS STS. In particular, the improved background rejection capability of the developed detector could extend the available experimental dynamic Q range, allowing it to measure weak reflectance phenomena.
We present a fault-tolerant Bell-pair distillation scheme achieving constant overhead through high-rate quantum low-density parity-check (qLDPC) codes. Our approach maintains a constant distillation rate equal to the code rate while requiring no additional overhead beyond the physical qubits of the code. Full circuit-level analysis demonstrates fault-tolerance for input Bell-pair infidelities below a threshold ∼10%, readily achievable with near-term capabilities. Unlike previous proposals, our scheme keeps the output Bell pairs encoded in qLDPC codes at each node, eliminating unencoding overhead and enabling direct use in distributed quantum applications through recent advances in qLDPC computation. These results establish qLDPC-based distillation as a practical route toward resource-efficient quantum networks and distributed quantum computing.
Numerical and experimental results are presented on the pullout phenomenon in composite materials at a high rate of loading. The finite element method was used, taking into account the existence of a virtual shear deformation layer as the interface between fiber and matrix. Experimental results agree well with those obtained by the finite element method. Numerical results show that the interlaminar shear stress is time dependent, in addition, it is shown to depend on the applied load time history. Under step pulse loading, the interlaminar shear stress fluctuates, finally decaying to its value under static loading.
This report documents the analysis and experimental validation of the performance of various aspects of a high rate bit synchronizer.
The performance and abuse characteristics of 55 D-size lithium-thionyl chloride (Li-SOCl2) cells are evaluated at relatively high rates. Results from the following tests are presented: shock test, vibration test, capacity performance, uninsulated short circuit, high temperature exposure, and overdischarge.
Abstract Li‐air batteries are considered strong candidates for the next‐generation energy storage systems designed for electrical transportation. However, low cyclability and current rates are two major drawbacks that hinder them from further realization. These issues necessitate the discovery of novel materials to significantly enhance the redox process of discharge products. In this study, a novel catalytic system comprised of tin sulfide (SnS) nanoflakes as a solid catalyst and tin iodide (SnI 2 ) as a dual‐functional electrolyte additive is discovered. This system enables operating the battery at high current rates up to 10 000 mA g −1 (corresponding to 1 mA cm −2 ). The SnS catalyst shows outstanding catalytic activity for both oxygen reduction and evolution reactions compared to carbon, noble metals, and other transition metal dichalcogenides. It also exhibits good structural integrity at high rates. The computations indicate numerous possible oxygen reduction sites without oxygen dissociations on the SnS surface through solution mechanism that is likely responsible for the formation of Li 2 O 2 . The calculations also indicate that the role of the SnI 2 is not only reacting with the lithium anode to provide protection but reducing the charge potential by promoting catalytic decomposition of the Li 2 O 2 . This work provides new novel additives for designing high‐rate Li‐air batteries.
A four-port magic-T hybrid waveguide junction serves as the central component of a high-efficiency two-way power combiner circuit for transmitting a high-rate phase-modulated digital signal at a carrier frequency in the Ka-band (between 27 and 40 GHz). This power combiner was developed to satisfy a specific requirement to efficiently combine the coherent outputs of two traveling-wavetube (TWT) amplifiers that are typically characterized by power levels on the order of 100 W or more. In this application, the use of a waveguide-based power combiner (instead of a coaxial-cable- or microstrip-based power combiner, for example) is dictated by requirements for low loss, high power-handling capability, and broadband response. Combiner efficiencies were typically 90 percent or more over both the linear and saturated output power regions of operation of the TWTs . Figure 1 depicts the basic configuration of the magic-T hybrid junction. The coherent outputs of the two TWTs enter through ports 1 and 4. As a result of the orientations of the electromagnetic fields, which also provides a needed high port-to-port isolation, of these two input signals and the interior design of the magic-T junction, the input powers are divided so as to add in phase at one output port (port 2), and to be opposite in phase and hence cancel each other at the opposite coplanar output port (port 3). The net result is that the output power at port 2 is essentially double that of the output of one TWT, minus the power lost in the magic-T hybrid junction. Optimum performance as a high-efficiency power combiner thus requires a balance of both power and phase at the input ports of the magic-T. Replicas of this two-way combiner can be arranged in a binary configuration to obtain a 2n-way (where n is an integer) combiner. For example, Figure 2 illustrates the use of three two-way combiners to combine the outputs of four TWTs.
We present performance data for low-noise free-running high-rate photon counting method for space optical communication and ranging. NASA GSFC is testing the performance of two types of novel photon-counting detectors 1) a 2x8 mercury cadmium telluride (HgCdTe) avalanche array made by DRS Inc., and a 2) a commercial 2880-element silicon avalanche photodiode (APD) array. We successfully measured real-time communication performance using both the 2 detected-photon threshold and logic AND-gate coincidence methods. Use of these methods allows mitigation of dark count, after-pulsing and background noise effects without using other method of Time Gating The HgCdTe APD array routinely demonstrated very high photon detection efficiencies ((is) greater than 50%) at near infrared wavelength. The commercial silicon APD array exhibited a fast output with rise times of 300 ps and pulse widths of 600 ps. On-chip individually filtered signals from the entire array were multiplexed onto a single fast output. NASA GSFC has tested both detectors for their potential application for space communications and ranging. We developed and compare their performances using both the 2 detected photon threshold and coincidence methods.
We present performance data for low-noise free-running high-rate photon counting method for space optical communication and ranging. NASA GSFC is testing the performance of two types of novel photon-counting detectors 1) a 2x8 mercury cadmium telluride (HgCdTe) avalanche array made by DRS Inc., and a 2) a commercial 2880-element silicon avalanche photodiode (APD) array. We successfully measured real-time communication performance using both the 2 detected-photon threshold and logic AND-gate coincidence methods. Use of these methods allows mitigation of dark count, after-pulsing and background noise effects without using other method of Time Gating The HgCdTe APD array routinely demonstrated very high photon detection efficiencies (50) at near infrared wavelength. The commercial silicon APD array exhibited a fast output with rise times of 300 ps and pulse widths of 600 ps. On-chip individually filtered signals from the entire array were multiplexed onto a single fast output. NASA GSFC has tested both detectors for their potential application for space communications and ranging. We developed and compare their performances using both the 2 detected photon threshold and coincidence methods.
A neighbor discovery protocol that enables the dynamic discovery of nodes for NASA Glenn Research Center’s High Rate Delay Tolerant Networking (HDTN) project is needed to satisfy mission scalability and interoperability objectives. The purpose of this study is to primarily examine a DTN IP neighbor discovery (IPND) implementation to understand the inner workings of the protocol before approaching a neighbor discovery implementation for the HDTN project. Using a rust-based DTN IPND implementation, this study analyzed the neighbor discovery process. DTN IPND was found to help meet both mission scalability and interoperability objectives by enabling dynamic routing capabilities. This study definitively answers the question regarding mission scalability and interoperability concerns. Further studies are needed to establish the most optimal neighbor discovery implementation for HDTN.
In order to meet ever-increasing data return requirements, more satellites are using the near-Earth Ka-band (25.5 – 27.0 GHz) to achieve higher downlink rates. The paper discusses the Universal Space Transponder - Ka-band Modulator (UST-KaM) developed at the NASA Jet Propulsion Laboratory for the NASA-ISRO SAR (NISAR) mission, which is capable of transmitting up to 1.74 Gbps with 7/8 LDPC encoding. The UST-KaM utilizes OQPSK with both baseband and RF filtering to contain the 1 Gsps transmission spectrum within the 1.5 GHz Ka-band, even with the use of an external, saturated amplifier. Due to the high data rates involved, several technical hurdles were overcome in both the digital and RF designs. The UST-KaM is a software defined radio with two digital circuit board assemblies: a low speed housekeeper board for commanding and telemetry, and a high-rate signal processing board known as the Signal Processing Module (SPM). The SPM receives data from the spacecraft via a SERDES interface at up to 2 Gbps, processes and encodes the data using a Xilinx Virtex-5 FPGA, and produces 1 Gsps OQPSK I and Q waveforms via synchronized, multiplexed DACs. The RF Electronics in the UST-KaM employ a heterodyne architecture in which the I/Q digital waveforms are filtered and then up-converted using a sub-harmonic IQ mixer. The LO of the converter, which is included in the exciter assembly, is at 13.125GHz, and the RF output is a 26.25GHz carrier which is modulated with the OQPSK waveforms. The output of the mixer is then filtered using low loss quartz thinfilm edge coupled Chebyshev filters and amplified through a series of low gain Ka-Band amplifiers. The exciter assembly also has a 2GHz, low-phase-noise, PLL synthesizer to supply the clock to the DACs for the high rate digital waveforms.
New physical insights and a robust approach are provided to develop super-MIEC anodes for high-rate batteries, which would bridge two materials families—nanoporous framework materials and conductive oxides.
The heat dissipation problem occurring in the lithium thionyl chloride cells discharged at relatively high rates under normal discharge conditions is examined. Four heat flow paths were identified, and the thermal resistances of the relating cell components along each flow path were accordingly calculated. From the thermal resistance network analysis, it was demonstrated that about 90 percent of the total heat produced within the cell should be dissipated along the radial direction in a spirally wound cell. In addition, the threshold value of the heat generation rate at which cell internal temperature could be maintained below 100 C, was calculated from total thermal resistance and found to be 2.9 W. However, these calculations were made only at the cell components' level, and the transient nature of the heat accumulation and dissipation was not considered. A simple transient model based on the lumped-heat-capacity concept was developed to predict the time-dependent cell temperature at different discharge rates. The overall objective was to examine the influence of cell design variable from the heat removal point of view under normal discharge conditions and to make recommendations to build more efficient lithium cells.
Ni-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathodes are investigated to realize high energy density Li ion batteries for long life electric vehicle applications. However, capacity decay and thermal instability due to cathode-electrolyte interfacial degradation remain challenges that require sophisticated surface stabilization methods to address. Here, we propose a strategy, for the first time, to form an artificial Li + -conducting cathode-electrolyte interphase (ALCEI) on the NCM811 cathode surface using a nucleophilic reaction between polysulfides and vinylene carbonate (VC). Furthemore, the as-formed ALCEI layer simultaneously protects the NCM particles from electrolyte corrosion and facilitates Li + ion transport, thus enabling stable and high rate cycling of NCM811. As a result, the ALCEI-modified NCM811 cathode exhibits a high capacity (211.6 mA h g -1 at 0.1C), notable rate capability (134 mA h g -1 at 10C), and superior cycle stability (94.2% over 200 cycles at 1C). These results underscore the use of interfacial engineering in high voltage cathode material development and provide a feasible strategy for stabilizing Ni-rich cathode interfaces in practical Li ion battery applications.
We report the solenoidal large intensity device (SoLID) at Jefferson Lab will push the boundaries of luminosity for a large-acceptance detector, which necessitates the use of a light-gas threshold Cherenkov counter for online event selection. Due to the high luminosity, the single-photon background rate in this counter can exceed 160 kHz/cm 2 at the photosensors. Therefore, it is essential to validate the high-rate limits of the planned photosensors and readout electronics in order to mitigate the risk of failure. We report on the design and an early set of studies carried out using a small Cherenkov counter in a high-rate environment up to 60 kHz/cm 2 , in Hall C at Jefferson Lab. Commercially available multi-anode photomultipliers (MaPMT) and low-cost large-area picosecond photodetectors (LAPPD) were tested using the JLab FADC250 modules for readout. The test beam results show that the MaPMT array and the internal stripline LAPPD can detect and identify single-electron and pair-production events in high-rate environments. Due to its higher quantum efficiency, the MaPMT array provided a better separation between the single-electron and the pair-production events compared to the internal stripline LAPPD. A GEANT4 simulation confirms the beam test performance of our counter device.
Ammonia (NH 3 ) is an essential ingredient in agriculture and a promising source of clean energy as a hydrogen carrier. The current major method for ammonia production, however, is the Haber–Bosch process that leads to massive energy consumption and severe environmental issues. Compared with nitrogen (N 2 ) reduction, electrochemical nitrate reduction reaction (NO 3 RR), with a higher NH 3 yield rate and Faradaic efficiency, holds promise for efficient NH 3 production under ambient conditions. To achieve efficient NO 3 RR, electrocatalysts should exhibit high selectivity and Faradaic efficiency with a high NH 3 yield rate. In this work, we developed two-dimensional (2D) iron-based cyano-coordination polymer nanosheets (Fe-cyano NSs) following in situ electrochemical treatment for high-rate NO 3 RR. Owing to the strong adsorption of nitrate on Fe0 active sites generated via topotactic conversion and in situ electroreduction, 2D Fe-cyano electrocatalyst exhibits high catalytic activity with a yield rate of 42.1 mg h –1 mgcat –1 and a Faradaic efficiency of over 90% toward NH 3 production at –0.5 V (vs reversible hydrogen electrode, RHE). Further electrochemical characterizations revealed that superhydrophilic surface and enhanced electrochemical surface area of the 2D porous nanostructures also contributed to the high-rate NO 3 RR activity. Finally, an electrolyzer toward NO 3 RR and oxygen evolution reaction (OER) in a two-electrode configuration is constructed based on 2D Fe-cyano, achieving an energy efficiency of 26.2%. This work provides an alternative methodology toward topotactic conversion of transition metal nanosheets for NO 3 RR and reveals the often-overlooked contribution of hydrophilicity of the catalysts for high-rate electrocatalysis.
Hybrid systems that integrate electrochemical CO 2 reduction with microbial upgrading offer a viable route to high value organic compounds from CO 2 at ambient conditions. However, electrocatalyst deactivation in microbial growth media remains a key barrier, limiting efficiency and increasing cost. Here we show that a bioadaptive single-atom nickel catalyst (Ni SAC), coupled with genetically engineered Clostridium ljungdahlii, enables robust electrosynthesis of isopropanol (IPA) from CO 2 via a CO-mediated pathway. Instead of relying on H 2 as an electron carrier, the system applies high-rate CO formation in complex growth media, maintaining a tunable CO Faradaic efficiency up to 92%, which is 9.4 to 52.7 times greater than conventional Ag catalysts. This performance supports stable IPA production at current density of 10.8 A/m 2 and production rate of 161.3 mg/L/day. In situ Raman and X-ray absorption spectroscopy, together with theoretical calculations, indicate that the Ni SAC can resist competing organic adsorption and retain its coordination structure during CO 2 reduction in bioelectrolytes, providing a mechanistic basis for the catalyst stability and integrated process performance.