Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hardening rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Multiscale Richtmyer-Meshkov instability experiments to isolate the strain rate dependence of strength

Theoretical analysis of Richtmyer-Meshkov instability (RMI) experiments for solid strength shows that the strain rate for a given shock should be inversely proportional to the length scale of the sine wave perturbations when η 0 k , the nondimensional amplitude to wavelength ratio, is held fixed. To isolate the effect of strain rate on strength, free-surface RMI specimens of annealed copper were prepared with three perturbation regions with the same η 0 k but different length scales, characterized by the wavelength λ varying by a factor of 4.9 from 65 to 130 to 320 µ m . Three such targets with different fixed η 0 k ′ s were impacted to a shock pressure of 25 GPa, and the instability evolution was measured with photon Doppler velocimetry. Strengths estimated by comparing hydrocode simulation to the data increased from 700 to 1200 MPa as λ decreased. The different η 0 k targets exercised increasing amounts of plastic strain yet showed no evidence of strain hardening. Physical regime sensitivity analysis determined that for 320 − 65 µ m wavelength perturbations, the effective strain rates increased from 8.7 × 10 6 to 3.3 × 10 7 s − 1 , a factor of 3.8. Thus, the predicted strain rate scaling was mostly achieved but slightly suppressed by increased strength at higher rates. The RMI strength estimates were plotted against constitutive testing data on copper from the literature to show striking evidence of the strength upturn at higher strain rates. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 6061-T651 Aluminum Alloy from Plate

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The matters of interest here are the elastic-plastic response and ductile failure behavior of 6061-T651 aluminum alloy under the conditions described above. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of a modular $J_2$ plasticity model with isotropic hardening as well as a ductile failure model. Both included modules that accounted for temperature and strain rate dependence. The models were coupled with an adiabatic heating module to calculate the temperature rise due to the conversion of plastic work to heat. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s as well as four geometries of notched tension specimens and two tests on specimens with shear-dominated deformations. The test data collected allowed the calibration of both the plasticity and the ductile failure models. Most test specimens were extracted from a single piece of plate to maintain consistency. Notched tension tests came from a possibly different plate, but from the same lot. When using the model in structural finite element calculations, element formulations and sizes different from those used to model the test specimens in the calibration are likely to be used. A brief investigation demonstrated that the failure model can be particularly sensitive to the element selection and provided an initial guide to compensate in a specific example.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Irradiation effects on Al 0.3 CoCrFeNi and CoCrMnFeNi high-entropy alloys, and 316H stainless steel at 500 °C

To evaluate the potential of high entropy alloys (HEAs) for nuclear applications, two HEAs, Al 0.3 CoCrFeNi and CoCrFeMnNi, and a conventional Type 316H stainless steel (SS) were irradiated with 1 MeV krypton ions at 500 degrees C up to 1 dpa, and examined in-situ with a transmission electron microscope (TEM). After irradiation, a high density of ordered L1 2 nanoparticles was observed in Al 0.3 CoCrFeNi. In contrast, no phase transformation was observed in CoCrFeMnNi and 316H SS. In the thin foil regions of TEM samples, stacking-fault tetrahedra were observed in the HEAs. In the thick foil regions, interstitial dislocation loops were observed for all alloys, and the areal loop density increased linearly with foil thickness. The Al 0.3 CoCrFeNi had the largest loop size (the lowest density), followed by the CoCrFeMnNi and then the 316H SS. The higher loop nucleation rate in the 316H SS was attributed to carbon content. Finally, the degree of irradiation hardening was slightly lower for the HEAs than for the 316H SS, which is a promising sign for the nuclear application of HEAs at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simulation of dislocation evolution in microparticle impacts over a wide range of impact velocities

We report the dynamic loading environment created by high velocity microparticle impacts is very difficult to model. The extremely high strain rates, large deformations, and high temperatures affect the flow stress of the material in ways that standard flow stress models cannot capture. Plastic deformation and strain hardening in metals is controlled by the motion of dislocations. Dislocations can be nucleated, stored as forest dislocations, or be annihilated as loading progresses. A comprehensive accounting of dislocation density change is needed to accurately describe rate and temperature dependent dislocation glide and evolution across the wide rage of loading conditions present in microparticle impact problems. Therefore, we implement and apply a newly proposed flow stress model (Hunter and Preston, 2015, 2022) that is then coupled with mobile and immobile dislocation density evolution equations. This model is implemented in Los Alamos National Laboratory’s hydrodynamics code, FLAG, to model copper-on-copper microparticle impacts. This new strength model allows for accurate simulation of particle rebound and flattening across a wide range of impact velocities.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Response of Sulfonated Polystyrene Melts to Nonlinear Elongation Flows

Ionizable polymers form dynamic networks with domains controlled by two distinct energy scales, ionic interactions and van der Waals forces; both evolve under elongational flows during their processing into viable materials. A molecular level insight of their nonlinear response, paramount to controlling their structure, is attained by fully atomistic molecular dynamics simulations of a model ionizable polymer, polystyrene sulfonate. As a function of increasing elongational flow rate, the systems display an initial elastic response, followed by an ionic fraction-dependent strain hardening, stress overshoot, and eventually strain-thinning. As the sulfonation fraction increases, the chain elongation becomes more heterogeneous. Finally, flow-driven ionic assembly dynamics that continuously break and reform control the response of the system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Crystal plasticity modeling of strain-induced martensitic transformations to predict strain rate and temperature sensitive behavior of 304 L steels: Applications to tension, compression, torsion, and impact

This paper advances crystallographically-based Olson-Cohen (direct γ → α’) and deformation mechanism (indirect γ→ε→α’) phase transformation models for predicting strain-induced austenite to martensite transformation. Here, the advanced transformation models enable predictions of not only strain-path sensitive, but also of strain-rate and temperature sensitive deformation of polycrystalline stainless steels (SSs). The deformation of constituent grains in SSs is modeled as a combination of anisotropic elasticity, crystallographic slip, and phase transformation, while the hardening is based on the evolution of dislocation density and explicit shifts in phase fractions. Such grain-scale deformation is implemented within the meso-scale elasto-plastic self-consistent (EPSC) homogenization model, which is coupled with the implicit finite element (FE) method to provide a constitutive response at each FE integration point for solving boundary value problems at the macro-scale. Parameters pertaining to the hardening and transformation models within FEEPSC are calibrated and validated on a suite of data including flow curves and phase fractions for monotonic compression, tension, and torsion as a function of strain-rate and temperature for wrought and additively manufactured (AM) SS304L. To illustrate the potential and accuracy of the integrated multi-level FE-EPSC simulation framework, geometry, mechanical response, phase fractions, and texture evolution are simulated during gas-gun impact deformation of a cylinder and quasi-static tension of a notched specimen made of AM SS304L. Details of the simulation framework, comparison between experimental and simulation results, and insights from the results are presented and discussed.

304L steels↗
DOE OSTI2020

Microscopic dynamics of stress relaxation in a nanocolloidal soft glass

Here, we report x-ray photon correlation spectroscopy (XPCS) experiments with in situ rheometry performed on a soft glass composed of a concentrated suspension of charged silica nanoparticles subjected to step strains that induce yielding and flow. The XPCS measurements characterize the particle-scale and mesoscale motions within the glass that underlie the highly protracted decay of the macroscopic stress following the step strains. These dynamics are anisotropic, with slow, convective particle motion along the direction of the preceding shear that persists for surprisingly large times and that is accompanied by intermittent motion in the perpendicular (vorticity) direction. A close correspondence between the convective dynamics and stress relaxation is demonstrated by power-law scaling between the characteristic velocity of the collective particle motion and the rate of stress decay.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Reduced graphene oxide catalytically enhances the rate of cyanate ester curing under variable frequency microwave heating

Here, the curing of Lonza Primaset PT-30 novolac cyanate ester resin and EPON 826 bisphenol-A diglycidyl ether were investigated using convective thermal heating and variable frequency microwave (VFM) heating. The addition of 1 part per hundred reduced graphene oxide (r-GO) to PT-30 novolac cyanate ester increased the VFM cure rate compared to thermal heating. Curing it at 160°C for 240 min with VFM heating resulted in a 55% degree of cure compared to a 26% degree of cure with thermal heating. This observed VFM rate enhancement is due to selective microwave heating of the r-GO particles in the resin resulting in increased r-GO catalytic activity toward cyanate ester curing. It is both a thermal and catalytic effect, the latter of which is absent when r-GO is added to a bisphenol-A diglycidyl ether resin with o-phenylenediamine hardener. Impurities present in the PT-30 matrix do not appear to contribute to its overall cure kinetics, nor do they participate in the observed VFM rate enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evolution of microstructure and strength of a high entropy alloy undergoing the strain-induced martensitic transformation

In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe 42 Mn 28 Co 10 Cr 15 Si 5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. Here, the peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Rate and temperature independent model calibrations for J2 plasticity and Wilkins failure models for 17-4PH H1150 stainless steel

This memo’s objective is to report a calibration of the J2 plasticity model with the Wilkins ductile failure criterion for 17-4 PH H1150 stainless steel under slow loading at room temperature. The calibration of the hardening function was based on uniaxial tension tests, while that of the failure model included data from tension tests on notched specimens, a butterfly specimen shear test, and a set of interrupted compression tests on shear hat specimens. The procedure was that described in, minus the rate and temperature dependence.

36 MATERIALS SCIENCE↗
DOE OSTI2025

X-Ray Spectra from General Relativistic Radiation Magnetohydrodynamic Simulations of Thin Disks

We compare X-ray emission from several general relativistic, multifrequency, radiation magnetohydrodynamic simulations of thin black hole accretion disks with different accretion rates and spins. The simulations were performed using the M1 closure scheme, resolved with 12 frequency (energy) bins logarithmically spaced from 5 × 10 −3 to 5 × 10 3 ​​​ keV. We apply a general relativistic Monte Carlo transport code to postprocess the simulation data with greater fidelity in frequency resolution and Compton scattering treatment. Despite the relatively few energy bins and Kompaneets approximation to Compton scattering utilized in the M1 method, we find generally good agreement between the methods. Both produce prominent thermal profiles with peaks around 2–2.5 keV, where agreement is particularly strong and representative of the soft state. Both also find weaker (lower-luminosity) thermally sourced emission extending out to 100 keV due to the hotter innermost regions of the disks. Inverse Compton scattering becomes increasingly effective at hardening spectral outputs with increasing black hole spin, and becomes the dominant mechanism for photons that escape with energies between 10 to several hundred keV. At very high rates of spin, the radiation flux in this upscattered component becomes comparable to the thermal flux, a phenomenon typically associated with intermediate states. Beyond 10 4 keV, we observe faint, free–free emission from hot, optically thin coronal regions developing near the horizon, common to both spinning and nonspinning black holes.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Additive friction stir deposition of SS316: Effect of process parameters on microstructure evolution

Solid state nature of additive friction stir deposition (AFSD) additive manufacturing process is very advantageous in terms of defect formation and microstructural refinement in the material. Current study presents the process optimization, microstructural evolution and kinetics of recrystallization for AFSD deposited low stacking fault energy material - SS316. As deposited microstructure shows equiaxed ultra fine grains with an average grain size of ~5.0 ± 0.5 μm. Shear deformation at high temperature during processing leads to the operation of restoration mechanisms. Observation of necklace type microstructure in the as deposited SS316 is attributed to discontinuous dynamic recrystallization during processing. Recrystallization kinetics of the AFSD SS316 is characterized using Johnson-Mehl-Avarami-Kolmogorov (JMAK) model. Deformation – thermal cycling during AFSD process resulted in inconsistent recrystallization kinetics. Variation in strain, strain rate and temperature during processing with processing parameters result in varying microstructure and tool wear. Further, high strength-ductility combination and sustained work hardening in as deposited SS316 appear to arise from transformation and twinning during deformation, leading to the formation of hierarchical twins and martensitic phase after deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microscopic Mechanisms of Glasslike Lattice Thermal Transport in Cubic Cu 12 Sb 4 S 13 Tetrahedrites

Materials based on cubic tetrahedrites (Cu 12 Sb 4 S 13 ) are useful thermoelectrics with unusual thermal and electrical transport properties, such as very low and nearly temperature-independent lattice thermal conductivity (κ L ). We explain the microscopic origin of the glasslike κ L in Cu 12 Sb 4 S 13 by explicitly treating anharmonicity up to quartic terms for both phonon energies and phonon scattering rates. We show that the strongly unstable phonon modes associated with trigonally coordinated Cu atoms are anharmonically stabilized above approximately 100 K and continue hardening with increasing temperature in accord with experimental data. This temperature-induced hardening effect reduces scattering of heat carrying acoustic modes by reducing the available phase space for three-phonon processes, thereby balancing the conventional ∝ T increase in scattering due to phonon population and yielding nearly temperature independent κ L . Furthermore, we find that very strong phonon broadening leads to a qualitative breakdown of the conventional phonon-gas model and modify the dominant heat transport mechanism from the particlelike phonon wave packet propagation to incoherent contributions described by the off-diagonal terms in the heat-flux operator, which are typically prevailing in glasses and disordered crystals. Furthermore, our work paves the way to a deeper understanding of glasslike thermal conductivity in complex crystals with strong anharmonicity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Crack Growth Rate and Fracture Toughness Tests on Irradiated Ex-Plant Materials

The performance of structural materials is critical for the safe and economic operation of light water reactors. Exposed to neutron irradiation during service, the reactor core internal materials can undergo significant microstructural and microchemical changes, leading to irradiation hardening and embrittlement. To ensure the structural integrity and functionality of nuclear reactor components during long-term operation, material degradation and damage mechanisms must be understood and managed adequately. In this work, irradiated materials harvested from the decommissioned Zorita reactor were studied for their cracking susceptibility and fracture resistance as a function of irradiation dose up to 47 displacement per atom (dpa). The material is a Type 304 stainless steel sectioned from the baffle plates of this pressurized water reactor with 38 years of service. Crack growth rate and fracture toughness J-resistance (J-R) curve tests were performed in low-corrosion-potential environments at ~315°C. All samples behaved similarly under cyclic loading, and no deteriorated corrosion-fatigue behavior was observed in the test environments. Under constant stress intensity factors, most samples did not show elevated crack growth rates, suggesting an adequate stress corrosion cracking resistance in the test environments. However, an unstable cracking behavior was observed in a 47-dpa sample, resulting in significantly higher crack growth rates than expected at high stress intensity factors. Crack instability was also observed in a 0.06-dpa sample but did not lead to a sustained high crack growth rate. The impact of neutron irradiation was more evident in the fracture toughness J-R curve tests. As the dose increased, the J-R curve declined considerably and became very shallow at high doses. A fully intergranular fracture morphology was also observed among the high-dose samples ruptured in an air atmosphere at room temperature. This brittle fracture mode in the absence of high temperature water environment confirmed a high degree of embrittlement of this material resulting from its service exposure to neutron irradiation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

100 Gb/s High Throughput Serial Protocol (HTSP) for data acquisition systems with interleaved streaming

Demands on Field-Programmable Gate Array (FPGA) data transport have been increasing over the years as frame sizes and refresh rates increase. As the bandwidths requirements increase the ability to implement data transport protocol layers using "soft" programmable logic becomes harder and start to require harden IP blocks implementation. To reduce the number of physical links and interconnects, it is common for data acquisition systems to require interleaving of streams on the same link (e.g. streaming data and streaming register access). Further, this paper presents a way to leverage existing FPGA harden IP blocks to achieve a robust, low latency 100 Gb/s point-to-point link with minimal programmable logic overhead geared towards the needs of data acquisition systems with interleaved streaming requirements.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Defect-specific strength factors and superposition model for predicting strengthening of ion irradiated Fe18Cr alloy

Here, a high-purity binary alloy Fe18Cr was subjected to heavy-ion irradiation in order to provide improved understanding of the irradiation effect on radiation hardening associated with dislocation loop and network formation, α’ precipitation. The specimens were irradiated with 8 MeV Fe ions (~2 μm ion range) to midrange doses of 0.37 and 3.7 dpa at 300, 350 and 450 °C using dose rates of ~10 –5 –10 –3 dpa/s. Nanoindentation testing was performed to extract the bulk equivalent hardness at low depth from these ion irradiated specimens. High-quality transmission electron microscopy (TEM) images were acquired by utilizing a flash electropolishing method on the Focused Ion Beam (FIB) prepared liftouts. An accurate calculation of the strength factor was provided based on detailed TEM characterization of the irradiated microstructures. A newly refined hardening superposition method was applied to combine the strengthening components from each microstructure. The good agreement between microstructure predicted strength and measured strength further demonstrated the fidelity to use hardening model to quantify the mechanical properties of ion irradiated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Second Target Station Target Segment PIE Dose Estimates

The purpose of the analysis described in this document is to support post irradiation examination (PIE) future decisions as related to the Second Target Station (STS) Project. The STS Project is discussing plans for future PIE studies, and the radionuclide inventories and dose rates included in this study will aid decision makers as they consider the need for various PIE-related machinery. Three configurations of the lasagna-type target segment are evaluated for this analysis: a single bare tungsten plate, a slice of the segment containing a single tungsten plate, and the upstream half of a segment. The lasagna type target segment used in this analysis has a precipitation hardenable nickel alloy (UNS N07718 or inconel 718) shroud, copper (C10100) cladding, and pure tungsten plates. The target segment is evaluated for 10 years of operation followed by two decay periods: 6 months and 2 years. For each decay period, decay gamma dose rates are tallied 30 cm from the upstream, downstream, top, bottom, and sides of the configurations. Radionuclide inventories are also provided in this report separated by material. The highest dose rates calculated in this study are 2872 rem/hr 30 cm away from the top and bottom of the half-target configuration after 6 months of decay.

36 MATERIALS SCIENCE↗