Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gust load control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression

of a two part document. Part 2 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models, Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation." A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a semispan, aeroelastically scaled, wind tunnel model of a flying wing SensorCraft vehicle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree of freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid body modes. Gust load alleviation (GLA) and Body freedom flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.

Scott, Robert C.↗
NASA NTRS1980

Design for active flutter suppression and gust alleviation using state-space aeroelastic modeling

An analytical design technique for an active flutter-suppression and gust-alleviation control system is presented. It is based on a rational approximation of the unsteady aerodynamic loads in the entire Laplace domain, which yields matrix equations of motion with constant coefficients. Some existing rational approximation schemes are reviewed, and a new technique which yields a minimal number of augmented states for a desired accuracy is presented. The state-space aeroelastic model is used to design a constant gain, partial-feedback control system, which simultaneously assures stability and optimizes any desired combination of gust response parameters throughout the entire flight envelope.

Karpel, M.↗
NASA NTRS1957

Investigation at Low Speeds of Deflectors and Spoilers as Gust Alleviators on a Model of the Bell X-5 Airplane with 35 Degree Swept Wings and on a High-aspect-ratio 35 Degree Swept-wing-fuselage Model

Results of an investigation at low speeds to determine the gust-alleviation capabilities (reduction in lift-curve slope) of spoilers and deflectors on a 35 degree swept-wing model of high aspect ratio and on a 1/4-scale model of the X-5 airplane with 35 degree swept wings indicate that deflector and spoiler-deflector types of controls can be designed to provide considerable gust alleviation for a swept-wing airplane while still maintaining stability and control.

CONTROLS, SPOILER - COMPLETE WINGS↗
NASA NTRS2013

Optimal Recursive Digital Filters for Active Bending Stabilization

In the design of flight control systems for large flexible boosters, it is common practice to utilize active feedback control of the first lateral structural bending mode so as to suppress transients and reduce gust loading. Typically, active stabilization or phase stabilization is achieved by carefully shaping the loop transfer function in the frequency domain via the use of compensating filters combined with the frequency response characteristics of the nozzle/actuator system. In this paper we present a new approach for parameterizing and determining optimal low-order recursive linear digital filters so as to satisfy phase shaping constraints for bending and sloshing dynamics while simultaneously maximizing attenuation in other frequency bands of interest, e.g. near higher frequency parasitic structural modes. By parameterizing the filter directly in the z-plane with certain restrictions, the search space of candidate filter designs that satisfy the constraints is restricted to stable, minimum phase recursive low-pass filters with well-conditioned coefficients. Combined with optimal output feedback blending from multiple rate gyros, the present approach enables rapid and robust parametrization of autopilot bending filters to attain flight control performance objectives. Numerical results are presented that illustrate the application of the present technique to the development of rate gyro filters for an exploration-class multi-engined space launch vehicle.

Orr, Jeb S.↗
NASA NTRS1981

Design for active and passive flutter suppression and gust alleviation

Analytical design techniques for active and passive control of aeroelastic systems are based on a rational approximation of the unsteady aerodynamic loads in the entire Laplace domain, which yields matrix equations of motion with constant coefficients. Some existing schemes are reviewed, the matrix Pade approximant is modified, and a technique which yields a minimal number of augmented states for a desired accuracy is presented. The state-space aeroelastic model is used to design an active control system for simultaneous flutter suppression and gust alleviation. The design target is for a continuous controller which transfers some measurements taken on the vehicle to a control command applied to a control surface. Structural modifications are formulated in a way which enables the treatment of passive flutter suppression system with the same procedures by which active control systems are designed.

Karpel, M.↗
NASA NTRS1974

Specialists Meeting on Rotorcraft Dynamics, Moffett Field, Calif., February 13-15, 1974, Proceedings

Analysis of specific problems in rotorcraft dynamics. Topics include hingeless rotor theory, dynamic stall modelling, periodic systems identification, analysis of complex systems with phasing matrices, flapping stability, flap-lag dynamics at high advance ratios, finite element analysis and fuselage free-vibration characteristics, coupled rotor/frame vibration methods, gust response characteristics with unsteady stall effects, antiresonance theory, cyclic feathering motions and dynamic loads, control load envelope shaping, rotor aeroelasticity, use of Floquet theory, theory of proprotors and tilt-rotors, two-bladed teetering rotors, stability of air and ground resonance, vertical-plane pendulum absorbers, multicyclic jet-flap control, engine/frame interface dynamics, and others. The minutes of the question and answer periods following the presentations are presented in the supplement. Individual items are announced in this issue.

Source record↗
NASA NTRS1988

Digital active control law synthesis for aeroservoelastic systems

This paper presents a formulation for synthesis of digital active control laws for aeroservoelastic systems, which are typically modeled by large order equations in order to accurately represent the rigid and flexible body modes, unsteady aerodynamic forces, actuator dynamics, and gust spectra. The control law is expected to satisfy multiple design requirements on the dynamic loads, responses, actuator deflection and rate limitations, as well as maintain certain stability margins, yet should be simple enough to be implemented by an onboard digital microprocessor. The synthesis procedure minimizes a linear quadratic Gaussian type cost function, by updating selected free parameters of the control law, while satisfying a set of inequality constraints on the design loads, responses and stability margins. A stable classical control law or an estimator based full or reduced order control law can be used as an initial design starting point. The gradients of the cost function and the constraints, with respect to the digital control law design variables are derived analytically, to facilitate rapid convergence. Selected design responses can be treated as constraints instead of lumping them into the cost function, in order to satisfy individual root-mean-square load and response limitations. Constraints are also imposed on the minimum singular value requirements for stability robustness improvement.

Mukhopadhyay, Vivekananda↗
NASA NTRS1958

A Method for the Calculation of the Lateral Response of Airplanes to Random Turbulence

In this method, the gust velocities are represented as rolling gusts, yawing gusts, and side gusts. Random distributions of gust velocities across the span are taken into account in defining the rolling and yawing gusts. Complex stability derivatives are used to account for the random distribution of side gusts along the fuselage and vertical tail and the lag effects in gust penetration. A sample calculation procedure is presented for obtaining the response of the airplane in each degree of freedom.

LOADS, GUST - WINGS↗
NASA NTRS1977

Study of synthesis techniques for insensitive aircraft control systems

Insensitive flight control system design criteria was defined in terms of maximizing performance (handling qualities, RMS gust response, transient response, stability margins) over a defined parameter range. Wing load alleviation for the C-5A was chosen as a design problem. The C-5A model was a 79-state, two-control structure with uncertainties assumed to exist in dynamic pressure, structural damping and frequency, and the stability derivative, M sub w. Five new techniques (mismatch estimation, uncertainty weighting, finite dimensional inverse, maximum difficulty, dual Lyapunov) were developed. Six existing techniques (additive noise, minimax, multiplant, sensitivity vector augmentation, state dependent noise, residualization) and the mismatch estimation and uncertainty weighting techniques were synthesized and evaluated on the design example. Evaluation and comparison of these six techniques indicated that the minimax and the uncertainty weighting techniques were superior to the other six, and of these two, uncertainty weighting has lower computational requirements. Techniques based on the three remaining new concepts appear promising and are recommended for further research.

Harvey, C. A.↗
DOE OSTI2021

Design of a 3.4-MW wind turbine with integrated plasma actuator-based load control

Historically, cost reduction in wind energy has been accomplished by increasing hub heights and rotor diameters to capture more energy per turbine. The growth in rotor and turbine costs with increasing turbine sizes is also driven by the additional structure that must be added to withstand unsteady aerodynamic loads caused by turbulence, gusts, wind shear, misaligned yaw, upwind wakes, and the tower shadow. In this paper, we present a holistic design solution to integrate active load control using a controllable Gurney flap based on plasma actuators. We illustrate the design solution for a land-based 3.4-MW wind turbine rotor. Comparisons to a baseline reference 3.4-MW wind turbine show significant load reduction (15–18% DEL reduction for flap-wise blade root moments), rotor mass reduction (5–8%), and LCOE reduction (1.16–3.11%). To achieve these results, a comprehensive sequential-iterative design procedure is introduced to integrate the controllable Gurney flap into the turbine design and to drive the design solution toward the best LCOE reduction solution. Results are presented for mapping fatigue load reductions into cost reductions. In addition, an evaluation of active load control extended from Region-III to also include Region-II showed a further 34% reduction in DEL.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1999

Control Design Strategies to Enhance Long-Term Aircraft Structural Integrity

Over the operational lifetime of both military and civil aircraft, structural components are exposed to hundreds of thousands of low-stress repetitive load cycles and less frequent but higher-stress transient loads originating from maneuvering flight and atmospheric gusts. Micro-material imperfections in the structure, such as cracks and debonded laminates, expand and grow in this environment, reducing the structural integrity and shortening the life of the airframe. Extreme costs associated with refurbishment of critical load-bearing structural components in a large fleet, or altogether reinventoring the fleet with newer models, indicate alternative solutions for life extension of the airframe structure are highly desirable. Increased levels of operational safety and reliability are also important factors influencing the desirability of such solutions. One area having significant potential for impacting crack growth/fatigue damage reduction and structural life extension is flight control. To modify the airframe response dynamics arising from command inputs and gust disturbances, feedback loops are routinely applied to vehicles. A dexterous flight control system architecture senses key vehicle motions and generates critical forces/moments at multiple points distributed throughout the airframe to elicit the desired motion characteristics. In principle, these same control loops can be utilized to influence the level of exposure to harmful loads during flight on structural components. Project objectives are to investigate and/or assess the leverage control has on reducing fatigue damage and enhancing long-term structural integrity, without degrading attitude control and trajectory guidance performance levels. In particular, efforts have focused on the effects inner loop control parameters and architectures have on fatigue damage rate. To complete this research, an actively controlled flexible aircraft model and a new state space modeling procedure for crack growth have been utilized. Analysis of the analytical state space model for crack growth revealed the critical mathematical factors, and hence the physical mechanism they represent, that influenced high rates of airframe crack growth. The crack model was then exercised with simple load inputs to uncover and expose key crack growth behavior. To characterize crack growth behavior, both "short-term" laboratory specimen test type inputs and "long-term" operational flight type inputs were considered. Harmonic loading with a single overload revealed typical exponential crack growth behavior until the overload application, after which time the crack growth was retarded for a period of time depending on the overload strength. An optimum overload strength was identified which leads to maximum retardation of crack growth. Harmonic loading with a repeated overload of varying strength and frequency again revealed an optimum overload trait for maximizing growth retardation. The optimum overload strength ratio lies near the range of 2 to 3 with dependency on frequency. Experimental data was found to correlate well with the analytical predictions.

Newman, Brett A.↗
NASA NTRS1977

Detection by pilots of system failures during instrument landings

The effects of gust disturbances and the pilot's participation mode in the control task on his work-load level and failure detection performance during a simulated low visibility landing approach are examined. We found that the participation mode had a strong effect on the pilot's work load, the induced work load being lowest when the pilot acted as a monitoring element during a coupled approach and highest when the pilot was an active element in the control loop. The effects of differential work load and participation mode on failure detection were separated. The participation mode was shown to have a dominant effect on the failure detection performance, with a failure in a monitored (coupled) axis being detected significantly faster than a comparable failure in a manually controlled axis.

Ephrath, A. R.↗
NASA NTRS1975

Optimal control alleviation of tilting proprotor gust response

Optimal control theory is applied to the design of a control system for alleviation of the gust response of tilting proprotor aircraft. Using a proprotor and cantilever wing analytical model, the uncontrolled and controlled gust response is examined over the entire operating range of the aircraft except for hover: helicopter mode, conversion, and airplane mode flight. Substantial improvements in the loads, ride quality, and aeroelastic stability are possible with a properly designed controller. A single controller, nominally optimal only at the design point speed (160 knots here), operated efficiently over the entire speed range, with the possible exception of very low speed in helicopter mode. Kalman-Bucy filters were used as compensation networks to provide state estimates from various measurements in the wing motion, rotor speed perturbation, and tip-path-plane tilt.

Johnson, W.↗
NASA NTRS1977

Optimal control alleviation of tilting proprotor gust response

Optimal control theory is applied to the design of a control system for alleviation of the gust response of tilting proprotor aircraft. Using a proprotor and cantilever wing analytical model, the uncontrolled and controlled gust response is examined over the entire operating range of the aircraft except for hover: helicopter mode, conversion, and airplane mode flight. Substantial improvements in the loads, ride quality, and aeroelastic stability are possible with a properly designed controller. A single controller, nominally optimal only at the design point speed (160 knots here), operated efficiently over the entire speed range, with the possible exception of very low speed in helicopter mode. Kalman-Bucy filters were used as compensation networks to provide state estimates from various measurements in the system. Efficient control requires the measurement of the wing motion, rotor speed perturbation, and tip-path-plane tilt.

Johnson, W.↗
NASA NTRS1974

Exploratory tests of a simple aero-mechanical ride comfort system for lightly loaded aircraft

Some exploratory wind tunnel and radio-controlled free-flight tests were made with a small high-wing airplane model (1.23m wing span) to study the concept of a simple aero mechanical system intended to alleviate gust loads and improve ride comfort of lightly loaded aircraft. The system consisted essentially of the outer portions of each wing being hinged in the chordwise direction and connected directly to the wing flaps using internal counter weights to provide neutral mass balance. When the wing experienced a change in velocity or angle of attack, the movable wing panels, acting as sensors and flap actuators, deflected in response to the changes in lift on the wing. The corresponding movements of the interconnected flaps tended to reduce the changes in the wing lift.

Hewes, D. E.↗
NASA NTRS1976

Optimality study of a gust alleviation system for light wing-loading STOL aircraft

An analytical study was made of an optimal gust alleviation system that employs a vertical gust sensor mounted forward of an aircraft's center of gravity. Frequency domain optimization techniques were employed to synthesize the optimal filters that process the corrective signals to the flaps and elevator actuators. Special attention was given to evaluating the effectiveness of lead time, that is, the time by which relative wind sensor information should lead the actual encounter of the gust. The resulting filter is expressed as an implicit function of the prescribed control cost. A numerical example for a light wing loading STOL aircraft is included in which the optimal trade-off between performance and control cost is systematically studied.

Komoda, M.↗
NASA NTRS1981

Army/NASA small turboshaft engine digital controls research program

The emphasis of a program to conduct digital controls research for small turboshaft engines is on engine test evaluation of advanced control logic using a flexible microprocessor based digital control system designed specifically for research on advanced control logic. Control software is stored in programmable memory. New control algorithms may be stored in a floppy disk and loaded directly into memory. This feature facilitates comparative evaluation of different advanced control modes. The central processor in the digital control is an Intel 8086 16 bit microprocessor. Control software is programmed in assembly language. Software checkout is accomplished prior to engine test by connecting the digital control to a real time hybrid computer simulation of the engine. The engine currently installed in the facility has a hydromechanical control modified to allow electrohydraulic fuel metering and VG actuation by the digital control. Simulation results are presented which show that the modern control reduces the transient rotor speed droop caused by unanticipated load changes such as cyclic pitch or wind gust transients.

Sellers, J. F.↗
NASA NTRS2008

Aeroservoelastic Testing of a Sidewall Mounted Free Flying Wind-Tunnel Model

A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three j wind-tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, exible vehicles. In the rst of these three tests, a semispan, aeroelastically scaled, wind-tunnel model of a ying wing SensorCraft vehi- cle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree-of-freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid-body modes. Gust Load Alleviation (GLA) and Body Freedom Flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be own in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.

Scott, Robert C.↗